Search Documents

By H. Higuchi

The Sumitomo Metal Mining Company Ltd. (SMM) started to produce electrolytic nickel at the Niihama Nickel Refinery in 1939. In 1992, the conventional matte electrorefining process was converted to the matte chlorine leach electrowinning (MCLE) process, which is currently in practice. SMM has mainly used two kinds of nickel matte as the raw material for the MCLE process. Treatment of new raw materials, which have different impurity contents from the original nickel matte, has become mandatory because of changes in the market. Therefore, the MCLE process has been required to increase its flexibility to treat the different impurity contents in the new raw materials. An increase in the capacity for iron removal is included in such requirements. A new iron removal circuit in the MCLE process, based on a process development study, was recently installed. The iron removal circuit is in operation, and efforts are currently underway to optimize the performance of the circuit by changing the present operating parameters. In addition to the removal of the iron, the application is also expected to improve the nickel recovery. The outline of the new circuit and the current iron balance in the MCLE process are described in this paper, together with the effect of the circuit on iron treatment capacity.

Jan 1, 2006

By J. Kramer, T. Hartmann

In the Hydrometallurgical processes, the presence of the so-called “crud” is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design. The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the seriesconnected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation. The transfer of the organic phase into the electrolysis cell can result in a “burnout” of the cathode. The carry-over of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show. To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl®. By this means, we can guarantee our customers the maximum possible solvent recovery and minimise the solvent costs in this process step. This system is presented in detail in this paper.

Jan 1, 2012

By K Komori

Naoshima Smelter and Refinery has treated shredder residue and incinerator fly ash in Japan since 2003. As a highlight, a new incinerating and melting furnace, as well as fly ash washing treatment plant were newly constructed for pre-treatment of shredder residue and fly ash respectively, and the pre-treated materials are ultimately treated in the existing Mitsubishi continuous copper smelting and converting process line. Since wastes such as shredder residue tend to vary in size and in shape, and contain some chlorine, the installation of a new pre-treatment line was required. The combination of the new pre-treatment line with the existing Mitsubishi Continuous Copper Process line has created a highly efficient and environmentally friendly system for recovering and recycling of valuable metals that previously used to be sent to a landfill. This paper reviews the approach that Naoshima took to establish its current recycling business strategy.

Jan 1, 2007

The effect of long term exposure of full size bolts to corrosive environments is presented. A special test rig was used to test four bolts under different loading conditions. Four, X-grade identical profile bolts, each of 21.7 mm core diameters (23.7 mm full diameter) were subjected to prolonged corrosion testing using acid sulphate water. The pH value of the circulated water varied between 3.4 and 4.3. The corrosion exposure test period lasted three and half years. Two bolts were axially loaded to 10 and 20 tonnes force respectively, the third bolt was subjected to a 360 Nm torsion load and the fourth bolt was left unstressed to act as a reference bolt. After the test period ended, the bolts were stripped of their corroded coatings and weighted for weight loss. The diameter of each bolt was subsequently measured, and the loaded bolt samples were first tested non-destructively for tensile cracks and then tested for tensile failure. No cracks were found on post corrosion bolts tested non-destructively. The failure strength reduction on all four post-corroded bolts was significant, varying between 21% and 39%. The onset of corrosion was not confined to the targeted mid-section length of the bolt, however, the severest corrosion occurred at the anchored ends of the bolts.

Aug 1, 2013

By M. S. Alam, Jae-Chun Lee, M. Tanaka, K. Koyama

Extensive research work is being carried out at AIST for developing energy saving green technology for base and precious metals recovery. In the present work, a new flowsheet is developed for copper recycling from waste electronic circuit board where copper was recovered by leaching followed by solution purification and direct electrowinning of Cu(I) from ammoniacal alkaline solution. In this new technology, power consumption in EW circuit was greatly reduced. This paper describes the overall process with an emphasis on different aspects of solution purification where impurities were selectively removed by cementation and solvent extraction techniques under nitrogen atmosphere.

Jan 1, 2004

By P. C. Benedict, J. A. Titcomb

"The following description of the geology of the Northern Empire mine is recorded by the senior author, but is based on the observations and complementary mapping of both authors.The Northern Empire mine is a mile east of Beardmore, and 100 miles northeast of Port Arthur, Thunder Bay district, Ontario.Production started in March, 1934, and terminated in September, 1941. The total number of tons milled was 425,866, from which 153,103 oz. gold was recovered. The lowest level from which ore was mined was the 1,900- foot, but considerable drifting was performed on the 2,075-foot and 800 feet on the 2,415-foot, the deepest level,The vein strikes about N.72°E. and has an average dip of80°S. In stoped sections the quartz averaged about 2 feet wide. On the 1,725-foot level it was drifted on continuously for more than 7,000 feet. In the mine as a whole, practically no commercial ore was found beyond points 1,400 feet west and 1,800 feet east of the shaft. Conspicuous wall-rock alteration extended throughout this section, but not much beyond these limits. There was some splitting of the vein and widening of the alteration halo on the lower levels. The average general colour of the quartz changes with depth .The vein is in 'Keewatin' lava flows, to which it is almost conformable. It lies only a short distance south from the 'Timiskaming-Keewatin' contact ( Fig. 2). This contact is marked by a black graphitic fault. So far as is known the fault is parallel, or nearly parallel, with the flows in strike, but dips at 72°S., which is 5° flatter than the average dip of the overturned flows. A post-vein, almost flat sheet of diabase about 550 feet thick cuts outthe vein from about the 650- to the 1,200-foot level ( Figs . 1 and 3). If it was intruded along a fault, the fault had only minor displacement. A strong alteration halo extends to 200 feet above and below the diabase. The vein was conspicuous but in large part it was below ore grade for 100 feet or more above and below the diabase.-"

Jan 1, 1954

By M. A. Hardie

"CASES and mixtures of them are so common and so much a part of everyday existence that they become so taken for granted that their individual characteristics and idiosyncrasies rarely become of curiosity to others than those involved in tl1eir production, processing, treatment, transportation, and for utilization. The use of the most common and universal mixture of gases -air -is begun at birth by ail living creatures and their discontinuation of its use terminates existence. Modern man rides on air in his tires, rides through it for high-speed transportation, and uses it for his comfort in the heating and air conditioning of his domicile. It is neither the aim nor the in-tent, in the next few moments, to provide a panacea for even a portion of the problems inherent in the gas industry nor to delve deeply into any particular facet of its diversities. The purpose is primarily to touch upon some of the peculiarities and generally to consider approaches to employ in the pursuit of solutions."

Jan 1, 1959

By M. Santaluce

"The revamp of critical process assets that require a significant plant outage (shutdown) presents a unique and demanding set of challenges for plant operators. They are executed in a more complex Brownfield environment, typically with limited working space and often involve unknown conditions or scope. For plant operators, such a project is often a high cost event both in terms of opportunity cost of lost production and the resource cost of labor and materials. It can also be a high risk event in terms safety, environment, and future plant reliability/availability. This impacts current and future performance or Overall Equipment Effectiveness (OEE). In our experience, the sequential nature of the EPCM approach does not provide the proper framework to facilitate the level of coordination, stakeholder cooperation and detailed planning required to adequately address the construction and shutdown complexity of a critical asset revamp projects. This paper proposes a more integrated approach to handling shutdown revamps of critical assets. Its main thesis is to involve the key performing stakeholder groups early in the project lifecycle (engineering team, procurement team, construction team and plant operations) to form an integrated shutdown management team that is focused on ensuring delivered results are aligned with project objectives. In this model, the construction team executing the shutdown/construction is preparing the detailed shutdown/construction planning concurrently with detailed engineering and procurement planning. This allows construction/shutdown requirements to influence engineering and procurement, with the desire to optimize safety, speed, quality and cost. The paper also discusses how to overcome the procurement hurdle in applying such an approach. The outcome of this integrated approach is better planning, coordination, communication and alignment between the project stakeholders, a shutdown/construction driven planning approach that more fully addresses the challenges of these projects and delivered results that are aligned with project objectives."

Jan 1, 2015

By R. D. H. Wigmore

"The title of this paper probably sounds quite simple and self-explanatory. The problem, however, was not a simple one, and proved somewhat baffling and expensive over a period of years. After outlining the problem, and the methods which were used to overcome it, we will present our solution, or perhaps it would be more accurate to say the partial solution which we reached.We have in the cyanide circuit at Upper Canada two Dorr Single Tray Thickeners with 30 ft. diameter wood stave tanks 12 ft 4 1/ 2 in. deep. In the years prior to 1948, when the tonnage was 250 to 280 tons per day, two stage thickening was practised. As the tonnage was increased to 450, 500, and finally 560-600 the thickeners were used in parallel.Some settling problems were encountered, and in those days the means to combat these problems were very few. The only remedy was to dump in pounds and pounds of lime. Then along came a few reagents, and the writer remembers one in particular, - 11 Carboxel11 (carboxymethlycellulose). When water or solution was added to this reagent, the result was a gooey mass somewhat resembling tapioca. One drawback was that it stayed in this state, and didn't go anywhere. A method was finally developed of containing the mass (or mess) on a fine screen, and dissolving some of it was a fine spray of solution. The only thing the writer recalls was that it was not a very effective settling agent.Shortly after this time, along came the new flocculents, first a few, and then many, and our settling problems were over.But when the settling problem was solved at Upper Canada, some other problems were creeping up on us."

Jan 1, 1965

By Robert B. Wickham

"American Barrick has always balanced its aggressive operating approach with a conservative financial strategy. In fact, what enables their mining team to pursue such aggressive plans with confidence is the conservative financial strategy adhered to by the company. These policies are built on a prudent mix of gold linked financings, equity and gold price hedging.This paper outlines these policies and focusses in particular on American Barrick's gold price hedging program.IntroductionThe company's balance sheet at the end of 1990 clearly shows the wisdom of its conservative policies. Total assets have grown to over US$1 billion; cash has grown to US$312 million and shareholders' equity to US$645 million. All amounts included in this paper are quoted in U.S. dollars. Increased gold production and an effective gold price hedging program also combined to produce record income from operations, earnings and cash flow in 1990.The first half of 1991 is also indicative of the benefits of the company's conservative financial policies. Increasing production, together with its comprehensive gold hedging program, has generated increased earnings, even in a period of falling gold prices.All year-over-year numbers for the first six months are up. Gold production was 36% higher; earnings of $40.2 million $ 0.30 per share - were 46% higher than 1990.Barricks revenue continued to increase despite gold prices remaining unchanged during 1990. Barrick's hedging policy protects the company from falling gold prices on the basis that the upside looks after itself. Their hedging program - including various goldlinked fmancings - enabled Barrick to realize an average price of $437 per ounce of gold sold in 1990, compared with the Comex average gold price for the year of $384 per ounce."

Jan 1, 1991

By G. Langlands

"R. Tenbergen Is this flotation machine suitable in the flotation ofInco ball mill discharges where we have a coarse feed at 60% solids?Reply Experience has shown that there is not a significant increase in the wear life of these machines when handling coarse material (8 mesh) at 60% solids. A common practice in Europe is shut down on the week-ends.The material is allowed to settle and on start-up an injectic of air for 15 seconds is sufficient prior to start-up. At,mining we put our unit in the middle of a bank of 44 cells and in order to ensure severe sanding we shut the aker cell down while the remaining cells kept running. After 20-25 seconds of air the cell started without trouble.P. Mahant Is there a build-up inside the impellor shaft housing? Falconbrige Ltd.Reply There is no sand build-up but rather a scale build-up which due to a flexing action frees itself periodically. Part of the design of the machine permits a water injection into the shaft housing to free any build-up. This is done in Europe during the week-end shut down."

Jan 1, 1984

By Kari Niiranen, Andreas Boehm

LKAB (Luossavaara-Kiirunavaara AB) is operating underground iron ore mine, with three beneficiation and pelletizing plants in Kiruna, Northern Sweden. The wet low intensity magnetic separation (WLIMS) is regarded as the crucial part of silicate mineral separation from the ore. The Kiirunavaara iron ore deposit shows a rather low content of silica (ca. 2.3 to 3.3 % SiO2) but the silica grade is expected to increase in the deeper parts of the deposit. This can be problematic in the case of DR pellet quality with an average silica grade under 0.75 % SiO2. A laboratory scale methodology was developed for the systematic characterization of the ore for mineral processing with the focus on silicates at the Institute of Mineral Processing, University of Leoben. This methodology is combining mineralogical, geochemical and process mineralogical characteristics. Automated mineralogy (QEMSCAN) was used to study the modal mineralogy, the distribution of silicate minerals in different particle size classes after comminution, the deportment of silicon (Si) between various silicates and degree of liberation and intergrowth of magnetite and silicates. Based on the mineralogical investigations, actinolite, phlogopite and even quartz and albite are the predominating SiO2 bearing minerals in the ore. The important result of the investigations was the discovery of two separate subtypes within the high silica ore type B2 based on their mineralogy and mineral processing characteristics. The crucial part of the investigations of intergrowths and liberation of magnetite results was the magnetic separation tests carried out with the Davis magnetic tube. The binary intergrowths of magnetite and the silicate minerals (mostly actinolite) are the most common type of mineral association discovered. The significant characteristics in the intergrowths of magnetite and actinolite are the fine-grained magnetite inclusions in actinolite which may end up increasing the SiO2 grade in the magnetite concentrate despite magnetic separation.

Jan 1, 2016

By Q. J. Xu

In blasting sensitive areas, the use of traditional blasting for rock fracture is restricted. Soundless cracking technology has been presented to achieve rock fracture instead of blasting. However, when the diameter of a borehole is larger than 50 mm, it is very dangerous that the soundless cracking agent (SCA) will have a tendency to gush from the borehole, which also leads to cracking failure. In this paper, a new large scale borehole soundless cracking technology is presented, using a new enlarged drill bit and mechanical plugging, which could solve the hole gush problem. Experiments were made to measure the expansive pressure of the SCA working in boreholes of F40 mm and F100 mm. The difference between two sizes of cracking phenomenon was compared and analyzed to show that large scale borehole soundless cracking has larger expansion pressure and faster reaction speed than traditional soundless cracking. Based on the experimental data, finite element analysis was utilized to study the stress concentration and stress distribution between two neighboring large boreholes in several media during the cracking process. Using the data from experiments with finite element numerical simulation, the brittle material fracture condition was analyzed to design the parameters of the borehole mesh. With the theoretical analysis, the technological process and reference parameters of large scale borehole soundless cracking were proposed, including the borehole spacing, burden distance, depth of the borehole and so on. Then a single rock was cracked with the new enlarged drill bit and new plugging, and the results proved the feasibility of the new large scale borehole soundless cracking technology, which achieved the expected goal of improving the cracking ability and reducing the cracking time. This paper presents a new efficient rock cracking method for blasting sensitive areas, and which could apply to mining engineering, demolition engineering, excavation engineering and other engineering applications where there is a demand soundless and non-vibration fracturing of rock.

Aug 1, 2013

By A. F. Beck

Abstract Canada has opened up a geological province in ?Western Canada which offers a new .stimulus to oil exploration geophysics. The problems of instrumental technique, interpretation, and logistics involved in the exploration of this new territory are presented in this paper and some of the efforts being undertaken to overcome them are discussed. The scope of this programme, its possible trend and extent, especially when viewed .against the background of the exploration effort in the United States, is touched upon. Introduction The science of earth physics was first applied to the search for oil on this continent some twenty-five years ago when torsion balance and refraction seismic methods were initiated in the Gulf Coast area of the United States. Since that time advances in the various branches of the science have been sporadic as new fields for their use opened up in the search for deep salt domes as well as less well-defined geological structures; in the application to well logging as part of the exploitation of petroleum; and in underwater surveys, aerial surveys, etc. In the present paper, attention has been concentrated only on the Western Canada plains area because of the recent remarkable growth of geophysics as an oil finding technique in this region. The other prospective oil areas of the West Coast and the Eastern Provinces of Canada are at present of minor importance, although they will undoubtedly receive increasing consideration in the future as accessibility to markets becomes a major factor and more improved geophysical and geological techniques are developed. A vast province in Canada, covering some 655,000 square miles of prospective oil territory (approximately one-half of the prospective oil area in the United States), has provided the new sphere of activity for geophysics (see Figures 1 and 2). Included in this area are immense inaccessible, uninhabited frozen regions which pose a new problem in logistics and operational techniques.

Jan 1, 1950

By K. Ogawa, T. Yokoyama

Hydraulic fracturing technique, an applied technique to cause tensile fractures to rock by injecting water pressure to a certain closed section of the borehole, is a measurement method of in-situ rock stress. This technique has the highest track record for techniques used in sub 1000 meter. A feature of this technique is comparatively simple and easy for in-situ stress measurement, because the measurement is applicable when a drilled borehole is available. The predominant advantage of this method is that elastic constants such as Young’s modulus and Poisson’s ratio are not required for determining the value and direction of initial stress. The factors to determine the stress state are the water pressures of re-opening and shut-in of fractures around the borehole wall and its directions. With conventional methods, however, the accuracy of the derived stress states from the observation equations was often adversely affected by the lack of consideration of the remaining water pressure in fractures and insufficient stiffness of the pressurization system. We have developed a new hydraulic fracturing system based on a new test method concept overcoming these defects, and applied to a 300 meter deep borehole in granite. The most important improvement of the new system is an employment of a syringe pump which enables an accurate flow control of fluid with less than 1ml/min in the pressure of 30MPa. Therefore the new test system has a quick response for pressurising in the interval zone, and the measured data was confirmed extremely accurate.

Jan 1, 2015

By E. R. Rivenbark

"The coal handling plant represents an investment of about $100 million in coal handling and storage equipment. The coal receiving is done by a continuous ship unloader that can handle ships in the 60 000 T range at Q rate of 1750 /ph. A unique feature in the system is a stacker/reclaimer unit which will work inside a dome storage structure. The coal for the unit will include any low sulphur coal that can be delivered by sea at an economical price blended with New Brunswick high sulphur coal.ThE flue gas scrubber is a wet limestone system capable of 95% SO2 removal. The scrubber will utilize about 150 000 tonnes of limestone per year and will produce commercial grade gypsum by the forced oxidization method.IntroductionWith the need for new generating capacity being required, New Brunswick Power reviewed, in 1985, its options for the next unit. The study indicated that the most attractive option for New Brunswick Power would be a coal-fired unit capable of receiving imported coal at a sea port. The site selection process resulted in three site options being considered.The existing Coleson Cove and Dalhousie sites, and the Belledune site were considered. To meet load distribution needs, it was then decided that the unit had to be located in the northern section of the province, thus eliminating the Coleson Cove site. The Belledune site was selected because it had the capacity to have additional units added where as the Dalhousie site would have only been able to accommodate one unit"

Jan 1, 1994

By C. L. Lewis

"The development of computer process control at the Lake Dufault concentrator is reviewed and the on-stream X-ray analysis -computer system is described briefly. Some applications of the computer in metallurgical process control are described.The computer sequences slurry sample streams to the analyzer and translates the analytical results from voltage signals to elemental percentages. The required flotation reagent flow rates are calculated from analyses and mill-feed tonnage rates and the reagent feeders are set automatically to provide such flow rates. X-ray calibration time has been reduced from about 45 minutes to 15 minutes by the use of a computer program. Metallurgical and operating personnel have acquired the ability to program the computer and have extended the system capability to allow the calculation of recoveries, averaging of mill data, application of ore specific gravity in grinding control, control of oxidized ore flotation and the development of an economic recovery program."

Jan 1, 1971

By Jo Render

Expectations of your management approach ??Life of mine applicability ??Tailor scale of activity to scale of project ??Assess impacts, risks, and opportunities ??Use global good practice, backed up by rigorous analysis ??Support with trained monitoring and evaluation team ??Information infrastructure to allow ongoing trend analysis and tracking of progress ??Public reporting using standardized indicators Yes, we are talking about a ?management system?

May 1, 2011

By W. G. McBride

THE present demand for men with engineering training exceeds anything in the history of the profession. Recent estimates indicate that mechanization of war has reached such a stage that at least twelve horsepower is required now for every one horsepower needed to run the machines of the first Great War. The scale of operations exceeds anything in the past, while more territory and people are involved than ever before. Many of our allies have inadequate or no facilities for producing the thousand and one articles absolutely necessary to the conduct of modern warfare. Lack of preparedness has made it necessary to produce at an unparalleled rate to gain parity with the enemy, while our losses have been so heavy that replacement, in itself, presents a task which might well stagger less courageous peoples. This means that not only is there an unprecedented demand for engineers to produce the machines, munitions, and supplies of war, but there is a correspondingly large need for men with engineering skill in the uniformed forces to operate and maintain the vast numbers of ships, 'planes, tanks, trucks, radios, and a myriad of other devices to carry on the varied activities of war. This abnormal demand came upon us after almost ten years of stagnation in the engineering industries. During this time many trained engineers drifted into other callings, while the lack of jobs for graduates caused a falling off in the number of men training for this profession. Consequently, the supply of well trained engineers was below normal when the madman of Germany precipitated us into the present turmoil. Added to all this, we in Canada are still suffering from governmental inefficiency in the utilization of the available supply of engineers. In the armed forces, engineers have been assigned to office and other work where their engineering training is not only wasted but for which men with more suitable training could be found. Mining engineers are debarred from service as aeronautical engineers, and students in mining engineering are denied the bursaries provided for aiding students in engineering. Mining and metallurgical engineers are both barred from the Ordnance department of the army. This arises from a misunderstanding in relation to engineering training. In Canadian engineering schools, all engineers are given a sound training in the branches of human knowledge which are fundamental to engineering: mathematics, physics, and chemistry. The basic difference between the several categories of engineers lies in the fact that training in the application of this fundamental knowledge to the solution of engineering problems is given in different subjects.

Jan 1, 1942

By G. E. Rowan

"DURING the dark ages, the cherished dream of chemists was to find a process for converting base metal into gold. Many a wealthy-but-gullible patron lost a fortune in the search. Men who work with metals today are a bit more realistic. I haven't heard of a metallurgist who expects to develop any one alloy that will resist all corrosive media. In the field of stain-less steels, there are about forty different types of alloys that are used where corrosion is a •problem.A stainless product is ordinarily selected because it offers one or more of the following qualities:(1) Resistance to corrosion (2) Resistance to oxidation at high temperatures (3) Good mechanical properties at room temperature (4) Good mechanical properties at high or low temperature (5) Attractive appearance (6) Ease of maintenanceToday we are interested in discussing the stainless steel family of alloys because of their .ability to resist corrosion. We• will not try to explain the Theory of Corrosion. Let us assume that, when surface potential and oxide formations are properly controlled, iron will resist attack in various chemi.cal solutions. The addition of alloying elements to iron does this for stainless steels. The principal stainless alloys used by various Canadian industries are listed in the accompanying Table."

Jan 1, 1959