Search Documents

By Matt Manson

?? Current Exploration and Assessment ?? Overview of Potential Development ?? Infrastructure ?? Opportunities and Challenges ?? Renard? 1-10 kimberlite pipes and ?Lynx-Hibou? kimberlite dyke system within ?Foxtrot? property ?? 50/50 Joint Venture between Ashton (a subsidiary of Stornoway) and SOQUEM ?? Discovered 2001-2003 ?? Québec is routinely assessed as one of the top mining jurisdictions in the world ?? Agnico-Eagle Mines Ltd. Is Stornoway?s largest shareholder and a leading mine developer in Québec

May 1, 2008

By R. J. McLeod

"A new backfill plant was constructed in 1966 adjacent to the mill of Giant Yellowknife Mines. The reasons for the addition were to increase the storage capacity for sand fill, provide facilities for mixing cement with the fill for mine stope floors and provide a system for pumping fill to B -3 raise, a horizontal distance of 4700 feet from the mill. At the same time it was hoped to increase the density of the fill pumped underground.The plant consists of two only steel storage tanks of approximately 400 tons capacity of sand fill each. They are 17 feet in diameter and have conical bottoms. The cylindrical section is 28 feet high and the conical section 14 feet high. Each tank is fitted with water nozzles around the conical sections to remove solids at the required density. The water pressure on the nozzles is 150 lbs per square inch. The cyclones used to produce the sand back fill are located on top of the storage tanks. Five model Dl0B Kreb cyclones are used for this purpose. The vortex finders are 2 1/ 4 inch and the apex 1 1/4 inch. The cement silo or storage tank is located in the same building. It is a steel tank 17 feet diameter by 41 feet high with a conical bottom. The silo holds 250 tons of bulk cement, which is unloaded by air from a bulk highway carrier using 12 to 15 lbs air pressure. The cement is conveyed to the top of the silo, a distance of 70 feet from the ground by 450 lbs. of air.The mixing tank is a rubber lined steel tank 14 feet in diameter by 14 feet high. It is equipped with a Lightning Mixer supplied by Greey Mixing Equipment Ltd. The mechanism is driven by a 40 HP motor. The lower shaft is unsupported and is equipped with two 36 inch diameter axial flow turbine type rubber covered impellers. The backfill is discharged from the storage tank into the mixing tank by a 5"" x 4"" SRL-C pump powered by a 20 HP motor. A level control in the mixing tank regulates the rate of discharge of this pump through a Grinnell-Saunders automatic control valve. The cement silo is situated at such a height above the mixing tank to allow for a Rota-Lock, a small hopper and a cement feeder. The feeder is an Omega gravimetric belt type dry feeder with a Sensogram controller. The capacity of the cement feeder is 20 tons of cement per hour. The cement and backfill are mixed in the mixing tank at whatever ratio is required for the mine stope floors."

Jan 1, 1968

By F. Y. Grepe

"THE MOST common type of mine hoist is, as is very well known, that in which the a.c. wound rotor motor is the driving medium. The reasons for the use of the wound rotor motor are, of course, economic. This type of equipment has, during the years, proved to be very reliable and reasonably satisfactory. It is, in fact, still being installed and in some places where a very hard and exacting duty cycle is demanded. As an example, a 600 h.p. 2,300-volt job was recently installed at the Caledonia mine (1) at Glace Bay. This is a vertical. hoist in a shaft only 175 feet deep but it is, nevertheless, working hard bringing coal to the surface and in making a trip at a speed somewhat better than every 20 seconds.The control equipment for such installations usually consists of a pair of primary reversing contactors which are interlocked both mechanically and electrically, together with some form of secondary controller. This, in the case of small hoists, can be a drum controller and metallic resistors or, in the case of larger hoists, a magnetic contactor panel and metallic resistors or, alternatively, can be one of the various forms of liquid rheostats which are available. The liquid rheostats, if of the dipper type, may be manually operated or it may be operated by some form of servo motor mechanism. In the weir type of liquid controller, the electrolite is, of course, pumped in and out of the rheostat."

Jan 1, 1954

By Ben D. Thompson

Cemented Paste Backfill has proven to be of critical importance to the operation of a number of Canadian mines, primarily due to the rapid backfilling rate this method permits. In order to improve the efficiency of this backfill system (i.e. optimize binder contents, fill fence design, and the employment of two stage filling strategies) there is a requirement to better understand its geomechanical behaviour. In response, in-situ experiments have been conducted in long-hole stopes to quantify the evolution of total earth pressures and pore pressures at a series of instrumented points within both the core of the backfill and close to fill fences. The deflection of fill fences as a result of paste loading has been measured and additional instrumentation has also been employed to measure cement hydration, negative pore pressures, and blasting induced vibrations within fresh and cured paste backfill. Installing geotechnical instrumentation within an open long-hole stope can be an extremely complex procedure and this paper details the methods that have been successfully employed. Preliminary results are presented, and the pressures induced by backfill with differing binder contents, at a number of different in-stope locations are considered.

May 1, 2009

By Daniel D. M. Adams

In 2004, Rio Tinto started a major project to implement Mine Monitoring and Control (MMC) systems worldwide. A detailed selection processes was undertaken and migration to a standard system was started. Today systems are operating around the world and serve as the core of to many business processes. Implementations include highly union areas, large mines, centrally managed mines, and remote areas. Each implementation has unique challenges but all are working towards the common goal with common systems. This paper reviews two projects that Rio Tinto has deployed in diverse conditions. The projects are the Rossing Uranium upgrade from the original Wenco system to the common standard and Iron Ore of Canada?s general technology upgrade. Also discussed is the future of mining at Rio Tinto, specifically the drill automation projects, and how it is utilizing the common standard MMC systems.

May 1, 2010

By J. L. Barton, R. A. Murray

"This paper looks at how Syncrude Canada Ltd. is utilizing the Conveyor Belt Monitoring technology developed and patented by the Australian CSIRO and licensed to Syncrude by Conveyor Belt Monitoring of North America, Inc. The technology involves magnetizing the steel cables in the conveyor belts and detecting the fields produced by breaks, gaps or cable ends using special sensors which feed the signals into a multi- channel recorder to provide permanent traces of the various events taking place in the steel cable belts.The data is analyzed and combined with existing belt audit programs, to assist in predicting belt life, change-out criteria and belt design, belt loading and construction. All of these applications of the CBM technology leads to better utilization of resources and forms an integral part of the conveying system reliability program."

Jan 1, 1992

By J. R. Foster

Investigations into the effect of a variety of acid digestions on common rock-forming minerals demonstrated a considerable variation in the proportion of the total metal extracted. A similar situation applies to the analysis of a number of common rock types. In addition, grain-size variation has an effect on the amount extracted by certain digestions. This work indicates that considerable care needs to be given to selecting an appropriate acid digestion capable of determining metal held in particular components of a sample. By using partial extraction techniques, the identification of certain patterns of metal distribution, undetectable by normal methods involving total metal analysis, may be achieved.

Jan 1, 1973

By D. Nower

"The supply of copper is expected to be at a large deficit in 2012. To recover from these deficits mining companies are required to maximize production and there is no better way to accomplish this than to optimize the use of their mobile mining equipment fleets. To optimize these fleets, each equipment type has to be monitored in its own unique way. Automation would not only improve production, but also minimize the safety risks and eliminate planning errors. The automated vibration monitoring of multiple systems on the shovel can determine the machine’s condition at all times. This reduces unplanned downtime and keeps critical shovels in production. This paper will discuss the details of how shovels can be successfully monitored, continuously. INTRODUCTIONP&H Mining, part of Joy Global, is the world’s largest manufacturer of above-ground mining equipment. Its electric rope shovels, such as Figure 1, with capacities up to 115 tons (104.3 metric tons), are used for high production loading in surface mines; its draglines, such as Figure 2, have bucket capacities to 160 cubic yards (122 cubic meters). P&H also produces blasthole drills, mobile mining crushers and other essential mining equipment. Headquartered in Milwaukee, WI, the company does business on every continent, except Antarctica. ECONOMIC FACTORSDue to the global demands for metals and power, mines are required to operate at full capacity. Mine operations cannot afford any critical assets to shutdown unexpectedly; depending on the ore type and quality, downtime for a single shovel can be as much as $300,000 per hour.Electric rope shovels are one of the most critical assets in open pit mining. They are very large, complex machines with DC or AC motors, multiple reduction gearboxes (some of them complex planetary) and multiple large rolling element bearings. This complexity, combined with the tough 24/7 service, results in too much unplanned shovel downtime, which can affect the entire downstream process."

Jan 1, 2012

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By E. Y. Dougherty

Introduction As practised during the last two years at the Vipond Consolidated gold mine, mining geology has meant the application of geology to the problem of finding, developing, and mining ore. This article reviews the results attained in Vipond mining geology as thus defined. Most effort was directed toward clarifying and interpreting the tangible physical causes of vein and ore localizations, and in the following pages these questions are dealt with in considerable detail. Discernment of the influence of rock folding and deformation on the localization of veins, and of the influence of certain structures and rocks in or near carbonaceous zones on the localization of ore-bodies, have been the main practical results of the studies. Consideration of some of the geological features of the Porcupine area, and of the geology and mining experience of the principal producing mines, has helped toward a perspective of Vipond's ore-finding problems. These features are first discussed. The background and procedure for Vipond mining geology, and the major results of the geological mapping, are then summarized. Then follows a résumé of tangible factors that influenced vein, ore-body, and gold localizations; and, next, explanations of the facts ascertained. Because they were found of little utility, many fascinating problems, such as the origin and mode of emplacement of the veins and lodes(l), the ultimate source of the ore, and the physico-chemical and mechanical agencies affecting vein and ore formation, are treated cursorily or are neglected in these notes.

Jan 1, 1934

By W. Gan

The interactions between bitumen and quartz sands in aqueous solutions were studied with the objective of recovering residual bitumen from Athabasca oil sands froth treatment tailings. It was observed that the presence of various multivalent metal cation (Fe3-, Fe2+, Mg2+,Ca2+, etc.) increased the mutual coagulation between quartz particles and oil or bitumen droplets within certain pH ranges. While the increased coagulation was detrimental to the recovery of the bitumen since it lowered the degree of bitumen liberation from sands, this effect could be reduced or eliminated by the addition of organic chemicals such as citric acid, oxalic acid and EDTA. Among these organic chemicals, citric acid was found particularly effective even at very low concentration.

Jan 1, 2006

By R. Shamsodini, A. Poor Zaeif Doost, H. Haji Amin Shirazi, M. R. Garmsiri

"With columns being installed in rougher section at Miduk Copper Complex, the rougher feed mainly reports to rougher-scavenger cells. To evaluate the efficiency of regrinding circuit, we conducted flotation experiments on samples of the feed and the products of the regrinding circuit. The grade difference of these products at 85% recovery was considered as the efficiency index. Results show that, with weight recovery of the rougher-scavengers the efficiency of the circuit increases. Exclusion of the rougher-scavenger concentrate from the feed to the regrinding circuit, resulted in an increase in the efficiency index from 10.12 to 17.6%.INTRODUCTIONThe flotation circuit at Miduk Copper Complex consists of five flotation columns as roughers and ten mechanical cells as rougher-scavengers. According to design criteria, 75% of the final product was expected to be produced by the rougher columns, while most of the feed consisting of liberated valuable particles is introduced into rougher-scavengers. To liberate locked particles, the rougher-scavengers concentrate is introduced into the regrinding circuit (see Figure 1 below). The regrind mill is in reversed closed circuit with a secondary hydrocyclones cluster, and the cyclone overflow is introduced into three parallel cleaner columns. Cleaners concentrate reports to concentrate thickener and the column tailings is introduced into six mechanical cleaner-scavenger cells. The cleaner-scavengers concentrate reports to the regrind circuit(Figure 1)."

Jan 1, 2012

By Tim Mann

"Like other operating mine sites, Placer Dome Inc. - Campbell Mine has taken important steps over the last few years to address environmental issues.This paper will provide specific insights into the implementation of an environmental management system at Campbell. In particular, it will focus on how Campbell developed its plan of action; the lessons that have been learned; the over-all steps that are being taken to enhance environmental stewardship and effectively manage relationships with key stakeholders.IntroductionThe development of an Environmental Management System at Campbell Mine has been part of a general development in management practices which has taken place at the mine during 1990. This paper will discuss the components of the management system in the topic areas of: direction setting; environmental organization; issue assessment; emergency response plan; training ; monitoring/verification; reporting and data management; and relationship management.Although this paper focuses on environmental management systems, the development of this system has partly been a function of responses to other issues which have been addressed concurrently with environmental concerns. These other issues include development of operations management, human resources practices, and safety management practices at the mine. As the Environmental Management System developed, various stakeholders associated with local environmental concerns were identified. This group of stakeholders include the local community; municipal, provincial and federal governments; government agencies; Campbell employees; and the Placer Dome Inc. Corporation."

Jan 1, 1991

By David L. Anderson

This paper explores the financial impact of the initial version of the Saskatchewan Potash Reserve Tax; first, a one; and second, in conjunction with the other taxes affecting the industry's profitability. A though the introduction of the Reserve Tax is shown to lead to a substantia increase in a hypothetical firm's effective tax burden, the more unusual outcomes frequently attributed to this levy on y occur after the imposition of other non-provincial tax rulings. Despite this qualification, the results obtained suggest that the Reserve Tax undoubted y acted as a catalyst in the polarization of attitudes during the ear y period of industry/government confrontation

Jan 1, 1979

By O. Benavente, M. C. Hernández

Selenium is obtained mainly from copper anode slimes, which is a by-product of the copper electrorefining process. Selenium is present in copper anode slimes as silver and copper selenides. Traditionally, selenium has been obtained by pyrometallurgical processes; however, hydrometallurgy has now been incorporated either full or partial to the conventional process. Some hydrometallurgical processes are been developed and used at laboratory level an industrial scale. This document describes theoretical background and results of characterization and dissolution of selenium from a decopperized anode slimes in an alkaline oxidizing system. The results have indicated that the oxidizing leaching process reaches a practically complete dissolution of selenium (up to 90 %); the undissolved portion is due to the generation of a AgCl around the particle surfaces that delays the progression of the reaction. The results indicated that 90% of selenium extraction can be obtained by dissolution under moderate conditions of pH, temperature and reagent concentration in oxidizing medium. INTRODUCTION Selenium is distributed in the earth's crust in most rocks and soils. Selenium is essential, as it has wide range of applications in the medical and food industries as well as, used in semiconductor, sensors and photochemical devices. Selenium is rarely found in the native state, 90% of selenium is obtained from copper anode slimes, which is a byproduct of the copper electrorefining process (Lu, Chang, Yang, & Xie, 2015; Xiao et al., 2017; Yang et al., 2018). In anode slimes, selenium is present as an intermetallic compound, as Ag-Cu selenides. Currently, selenium is recovered from the anode slimes via hydrometallurgical and pyrometallurgical processes (Lu et al., 2015). The traditional pyrometallurgical method recovers selenium effectively, but faces difficulty as a result of increased energy costs and strict environmental regulations associated with the process (Li, Yang, Jin, Chen, & Tong, 2017). Therefore, hydrometallurgical processes are proposed in oxidizing medium such as nitric acid, alkaline leaching with sodium nitrate, wet chlorination and pressure leaching, amongst others (Hait, Jana, & Sanyal, 2012; Kim & Wang, 2010; Xiao et al., 2017; Yang et al., 2018).

Jan 1, 2019

By Carmen M. Neculita

Optimizing the long-term efficiency of passive systems for the treatment of highly contaminated acid mine drainage (AMD) is still a challenging issue. The optimization lies, among others, on improving the understanding and quantification of metal removal mechanisms in order to predict and enhance the stability of neo-formed minerals in secondary phases. Sorption, and precipitation as oxides-hydroxides, carbonates and bio-sulfides are likely the most important metal removal mechanisms involved in passive biotreatment of both slightly and highly contaminated AMD. In the same time, the preferred mechanism is precipitation of metal sulfides that are more stable and less pH dependent than carbonates and oxides-hydroxides. However, results of relatively recent research studies performed at laboratory scale showed that sulfides accounted only for up to 15% of total metals removed in passive bioreactors treating highly contaminated AMD dominated by iron (around 500 mg/L). Several approaches were used in the aforementioned studies to understand and quantify metal removal mechanisms in spent reactive mixtures collected from long-term (12-15 months) operating column bioreactors. These included: thermodynamic equilibrium modeling and various chemical extractions and mineralogical analyses (such as single and sequential extractions, acid volatile sulfides-simultaneously extracted metals determination, scanning electron microscopy, X-ray diffraction, and thermo-gravimetric analysis). The large proportion of metals (85%) removed by sorption and precipitation as oxides-hydroxides and carbonates suggests a relatively high mobility of the neoformed minerals, especially in low pH conditions. However, no data is available on the long-term stability of spent reactive mixtures and, on the implications for the sustainable management of this type of solid waste. Lately there is almost a consensus that the efficiency of highly contaminated AMD treatment is warranted by the use of multi-step passive systems, including both chemical and biological units, installed sequentially. However, very few well-documented studies are available on the design, construction, operation and long-term efficiency of these multi-step systems. A leading example is the tri-unit passive system installed on the abandoned Lorraine mine site (Québec) to treat a highly contaminated AMD dominated by iron (about 2,500 mg/L). This tri-step system (160 m3), consisting in two bioreactors separated by a unit filled with wood ashes, achieves to date a satisfactory removal of iron (up to 99%). Moreover, based on the data collected during laboratory testing, iron was mainly removed in the wood ashes unit (from around 3,200 mg/L to 10 mg/L) by precipitation of oxides-hydroxides as predominant mechanism and only partially by sorption. However, no data is available on the actual metal removal mechanisms in the field. Overall, theses multi-step systems are more complex and their long-term performance is even less predictable than the single unit systems. This paper presents the current knowledge and the research needs on metal removal mechanisms in passive bioreactors and multi-step systems for the long-term treatment of highly contaminated AMD. KEYWORDS

Aug 1, 2013

By John E. Udd

I N Part I of this paper, Professor Morrison suggested that our technique of causing cracks to develop around openings in a sheet of photoe1ashc plastic is, in effect, a laboratory-scale rockburst. Our investigations have indicated that the location and direction of these cracks are predictable, and that their growth can be controlled. On several occasions, we have been able to cause these cracks to propagate sufficiently slowly to be followed, with the naked eye. In practice, the rate of growth, gradual or sudden, would depend upon rock properties. This part of the paper presents an analysis of the stresses surrounding the openings before and after failure and also this author's views on the causes and after-effects of cracking. An attempt is made to correlate the stress patterns with those deter-mined from pure mathematics. Considering that the openings, except for the central enlargement, are long apertures with somewhat rounded corners, they might be compared with elongated ellipses having axes ratios of about 20:1 or with

Jan 1, 1963

By Guy Brouillard

A bow-tie analysis is a safety review methodology that uses a structured approach that can be qualitative or quantitative to document the potential risk of safety incidents. The bowtie diagram itself provides a powerful graphical representation of the threats barriers, events, and recovery measures which are readily understood by the "non-specialist". This presentation will discuss how mining operations can use this valuable tool within their operations to understand the risks and apply the appropriate safeguards toward reducing these risks to acceptable levels.

Jan 1, 2014

By G. A. Gross

Nearly 90 per cent of the iron ore produced in Canada is derived from iron-formation or bedded iron deposits. About 70 per cent of this consists of concentrates obtained fom iron-formation; another 20 per cent was formed by natural enrichment processes. Four principal varieties of iron-formation are recognized -the Algoma, Superior, Clinton and Minette types. Differences in their geology, mineralogy, chemical composition and environment of deposition are of special significance in their evaluation as ore.

Feb 1, 1966

By Qidong Xu

Abstract - The metavolcanic rocks of the Dahongshan area have been subjected to both widespread hydrothermal alteration from circulating seawater and to regional metamorphism, such that their mineralogic and chemical compositions have been changed significantly. Studies of immobile elements show that these rocks were originally tholeiitic basalts with geochemical characteristics of T-type MORB formed in a mid-ocean ridge environment. The accompanying Cu-Fe-rich VMS mineralization is in keeping with the original petrology and tectonic setting of these metavolcanic rocks. Regional alteration evident in K-Mg enrichment is related to sericitization and chloritization. Local alteration associated with Cu-Fe mineralization appears to have been accompanied by Si enrichment and Na depletion. P enrichment identifies metasomatism related to Cu-Fe reconcentration in the mineralized zone.

Jan 1, 1999