Search Documents

By E. Bratygin, G. Gazaleeva

"The article describes the analysis of methods and criteria of selectivity of optimal ore preparation schemes. Traditional criteria based on study of physical-mechanical properties of ores give the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production.Further on estimation is given to different criteria of the crushing selectivity, the new criterion is offered, the definition of which is done by results of an optical microscopy– the estimation of a valuable mineral release degree. The final estimation of the crushing process selectivity L? is performed by a calculation of a ratio of the valuable mineral free grains quantity in a desired size grade of a crushed material to the valuable mineral free grains quantity in a desired size grade of a raw product.Besides, optimality assessment of using the specific crushing unit is preliminary performed according to a maximum crushing degree of a material, however, the priority is given to the maximum selectivity criterion. The check of the proposed criterion was done when comparing the crushing of niobium bearing ores of the Vishnevogorskoye deposit in cone inertial and centrifugal impact crushers. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion L? showed that the centrifugal impact crusher (CC) has the value of the selectivity criterion lower than the cone inertial crusher (CIC). For the crusher CC the criterion L? is 0.82 – 0.87 units, whereas for the crusher CIC – 1.43-1.755 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 120°, peripheral speed of a cone rotation – 1,420 rpm, specific energy consumption – 6.99 kW?t/t.INTRODUCTIONIt has been shown that the most efficient techniques of mineral raw materials disintegration are selective crushing enabling to produce liberation of particles at maximum use of destruction techniques by borders of minerals cleavage. These days, such techniques are usually called special disintegration techniques (Jankovic & Valery, 2015), and they are used in 3–4 crushing stages. The selection of optimal crushing techniques is performed based on the following main parameters:- degrees of crushing, calculated based on granulometric features of raw and crushed products;- selectivity criterion defined according to useful mineral release and slime ability degree; and- traditional criteria (Gazaleeva et al., 2015) of choice based on study of physical-mechanicalproperties of ores gives the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production."

Jan 1, 2016

By Ben Sheneider

AT THE Flin Flon plant of the Hudson Bay Mining and Smelting Co., Limited there are two types of multiple hearth furnaces used in the roasting of sulphides. This pa-per will deal primarily with the wedge-type furnace in the roasting of zinc concentrates. The other furnace, the Nichols-Herroshoff type, is used in the copper smelter and is described in the papers given by (1) J. H. Ambrose in 1935 and (2) R. E. Mast and G. H. Kent in 1954. The design and operation of these roasting furnaces at the present time is essentially the same as given in the write-up in 1954. No at-tempt will be made here to describe these furnaces, except to mention that there are five Nichols-Herreshoff multiple-hearth furnaces, four of which are used to roast a dried mixture of copper concentrate, zinc plant residue, and flux, before this material is fed to the reverberatory furnace.

Jan 1, 1961

By J. Clark

Erosion control during the mining cycle can be more effectively planned using Erosion and Sedimentation Control Plans (ESCPs). This raises the issue of who should develop an Erosion and Sedimentation Control Plan Guidance document (ESCPG) to standardize the content of ESCPs. A search for ESCPG documents in Canada revealed no examples for mine sites. In the U.S. there are a number of regulatory authorities who developed such documents for mine sites, including EPA. An ESCPG is expected to result in: (a) plans will be more standardized (b) more clarity and efficiency for those generating ESCPs; (c) assisting regulators tasked with reviewing/approving ESCPs; (d) providing guidance for the mine effluent permitting process relative to sediment control; (e) providing a basis for developing and including ESCPs in the Environmental Assessment (EA) phase and the mine economic assessment; (f) applying and optimizing ESCPs above the ?watersheds? of sediment ponds; (g) utilizing the ESCPG document for ?exploration? sites; (h) lowering the risk of adversely impacting water quality downstream of mining activities; (i) providing a methodology for determining the need for sedimentation pond(s) during the construction and production phases; and (j) providing a clear environmental sustainability message relative to sediment control if the mining industry takes the lead in developing an ESCPG. ESCPs will proactively create increased administrative (regulatory) efficiency in the EA and sub-EA reviews relative to erosion control and sediment release from mine sites. This also assists the new initiative in BC, One Project, One Process (OPOP) and synchronous permitting (a variation of concurrent permitting): as an example, enhanced erosion control planning at the EA phase then allows the synchronous permitting initiative to proceed efficiently, particularly for the mine permit (Ministry of Energy, Mines and Natural Gas) and effluent permit (Ministry of Environment). Approximately twenty more management plans (e.g. ARD/ML, explosive management, emergency response, hazardous waste, sediment pond operation, environmental effects, environmental sampling, etc.) may also be entered into the EA process to create increased efficiency, and then feed into the synchronous permitting effort. The BC OPOP initiative also adds support to the Canadian Federal ?One Project, One Review Process? approach. The ESCP and a sediment pond management plan will also address the Canadian Metal Mining Effluent Regulations requirement for all discharges from mine sites to meet a grab sample of 30 mg/L Total Suspended Solids.

Aug 1, 2013

By L. C. Johnston, J. N. Gills

This paper reviews the basic reactions of the blast furnace and the open hearth furnace, and then discusses the quarrying and sizing requirements of the limestone feed for each. Particular emphasis is placed on the lime-stone at Irish Cove, now being mined under an agreement between Scotia Limestone Limited and Dosco Steel Limited. The drilling and blasting operations are described, along with loading and haulage, plant flow, water supply, power supply and transportation facilities.

Jan 1, 1967

By John Crusius

? 3-year research program overview ? initial results- MainZone pit Waterline pit ? questions raised ? increasingly common in western N. America ? frequently low-pH waters with elevated concentrations of many metals ? water quality controls poorly understood ? some in U.S. are Superfund sites

May 1, 2002

By Rénard Chaigneau

Quality during induration Drying ??40% of energy ??Drying velocity = f(1/radius2) ??Size versus risk of condensation ??Flow is important (minimise fines)Oxidation ??IOC Fe2+ typically 0.04% ??Important to minimise Fe2+forLow Temperature Disintegration ??Tight size distribution is key13

May 1, 2011

By P. M. STILES

Acquired in 1957, the limestone quarry of Ideal Basic Industries on Texada Island north of Vancouver has become a major supplier of high purity limestone and construction stone. Crushed limestone products are shipped by barge to various destinations along the B.C. and northern U.S. coasts.

Jan 1, 1984

By H. A. Wilson

Introduction Salt (sodium chloride) occurs naturally either in the solid state as rock salt or in solution as a component of natural brines. It is the major saline constituent of sea water, which contains about 4 percent salt-roughly 164 million tons, or enough to meet world salt demands for five years, per cubic mile. The great rock salt deposits of the world are generally regarded as having been formed by the evaporation of sea water over long periods of rime in wholly, partially, or periodically cut-off bays of ancient oceans. History and Occurrence of Salt in Canada We can speak today of the vastness of Canada's salt resources, but it was not always so. Settlement of our Atlantic seaboard and the Sr. Lawrence valley began in earnest in the early 1600's. The first small commercial salt works in Canada did not come into operation until 1866. Thus, for some two and a half centuries, the inhabitants of this growing country were entirely dependent on foreign sources for every pound of salt they consumed. The record shows that from at !east 1800 onward, the need for a domestic salt industry was clearly recognized by the governments of the day. It was during the Western Ontario oil-boom of 1866 that the initial discovery of rock salt in Canada was made, not far from Goderich, at a depth of 1,000 feet. A salt company was promptly organized, and with their operations there began the gradual and still uncompleted conquest of the Canadian salt market by the Canadian salt industry. Over the next thirty years many holes were drilled into the Salina formation both in Ontario and Michigan, and encountered rock salt. A vast salt-basin was disclosed, approximately outlined, and given the name Ontario-Michigan Salt Basin. The Ontario portion of the basin extends over at least 3,500 square miles, is met with at a depth varying between 800 and 1,600 feet, and has a thickness of 50 to 250 feet. No attempt has ever been made, so far as we know, to calculate the total salt reserves of this basin, but the minimum indicated in the Ontario portion by the figures just cited is just under thirty-five cubic miles. The specific gravity of rock salt is 2.2. From these data, those so inclined may calculate the tonnage.

Jan 1, 1947

The influence of joint orientation and joint persistence, on the mechanical behaviour of jointed rock masses under uniaxial compression, has been studied systematically. The joint inclination angle ß was varied from 0° to 90° with an increment of 15°. The joint continuity factor k was taken as 0.2, 0.4, 0.6 and 0.8. The peak strength, Young’s modulus, the complete axial stress-axial strain curves, the cracking process and the characteristic of the fragments, were investigated. It was found that the anisotropic response of the jointed specimens was governed by the micro-mechanism, such as crack initiation, propagation and coalescence, crack opening or closing, and frictional slip of cracks or joints. With the increase of joint continuity factor, the axial stress-axial strain curves change from single-peak to multipeak, the peak strength and Young’s modulus decrease. The specimens with medium joint inclination angle (30°,45° and 60°) has lower energy dissipation and strength due to stepped or shear failure, while specimens with small and large joint inclination angle (0°, 15°, 75° and 90°) has higher energy dissipation and strength due to axial cleavage or crushing failure.

Jan 1, 2015

By Roger Davieds

FACT: a company?s profitability (or loss) is directly related to the efficiency and effectiveness of its maintenance operation. Fact: in order to contribute in a positive manner, maintenance must understand what its true purpose is in the organization. It is easy to say our main purpose is to increase: ?equipment uptime ?OEE ?asset life cycle We all understand this; so does management.

May 1, 2010

By J. K. Atherton

If the metals sector is to contribute successfully to sustainable consumption we must adopt principles and practices which address the entire life cycle of the materials we produce. Progress must be founded on a sense of shared responsibility for the resources we utilize and the materials we create - it is this integrated approach which lies at the heart of materials stewardship. Materials stewardship means mining and metals companies producing materials in a responsible manner and then working with others, beyond their site, to ensure that the downstream material flows and applications are managed properly to create maximum societal value. In September 2006 ICMM published 'Maximizing Value: Guidance on implementing materials stewardship in the minerals and metals value chain'. This document takes a practical view presenting structured guidance as well as good practice case studies. In the publication, materials stewardship is described in terms of the range of activities that can be undertaken to ensure that all parties work collectively toward the responsible use of metal and mineral resources. This paper introduces the materials stewardship concept as set out in `Maximizing Value' and describes the business case for implementation as well as the ICMM framework for promoting materials stewardship.

Jan 1, 2007

By L. Van Wyk, J. Fernandez, J. Suarez, L. J. Diaz, A. Uria, D. Breeuwer

"Ventilation is an essential component of any underground mine, playing a vital role in ensuring the health and safety of workers, and a mine’s continuous operation. At a time when mining companies are increasingly having to move to deeper underground operations in pursuit of high-grade ore-bodies, the search is on for more efficient ventilation systems that will allow mining to be carried out at even deeper levels whilst ensuring the protection of workers and the maximisation of productivity through temperature management and the lowering of energy costs. Mining companies today are looking for innovative ways to deliver new technologies and procedures to enhance their mine’s profitability. Energy consumption by mine ventilation systems is higher than ever due to stringent specifications of underground equipment (primarily combustion engine emissions), air quality standards and mining at deeper levels which all require more powerful ventilation systems. With energy costs associated with operating ventilation systems being a mine’s second-highest cost of production after labour, finding the optimal ventilation solution is critical to a mine’s performance. Proper fan design remains a major factor in reducing capital expenditures (CAPEX) and operational expenditures (OPEX), which means that there are compelling reasons for making use of comprehensive factory testing at full power before fans are dispatched to site to simulate the mine’s current and future design requirements, and thus verify the fan’s effectiveness in ‘real’ conditions.INTRODUCTION A primary mine fan is considered the heartbeat of the entire mine ventilation system, drawing fresh air from the surface and providing a safe environment for miners. A ventilation system’s lack of performance often leads to a reduction in acceptable air quality levels for underground working operations and can potentially have an adverse impact on production rates."

Jan 1, 2019

By G. A. McGuffin

"IntroductionWITH the increase in quantity of sour gas reserves in the Province of Alberta, and the wider market for sulphur brought about by mounting world demand and restrictions placed on the principal supply, it was inevitable that this important source of sulphur would be .developed. In the light of these facts, it seems timely that a general paper on sulphur recovery from petroleum gases be presented. This, then, is the purpose of the following text. A short discussion of each of the following subjects is presented:(1) Properties and uses of sulphur(2) Existing sources(3) Market research(4) The recovery process in Turner Valley(5) Hazards of sulphur productionNo pretext of originality of material is made since innumerable reports have been prepared on this and related topics and information contained in these has been used quite liberally.Properties and uses of SulphurSulphur is a non-metallic element having an atomic weight of 32.06. The stable crystalline form at atmospheric temperature is referred to as 'rhombic' sulphur. It is bright yellow and has a specific gravity of 2.05, equivalent to 129.2 lb./cu. Ft. Above 204°F. sulphur has another stable crystalline form, referred to as 'monoclinic'. This is reddish-brown and is slightly less dense than the rhombic variety (122.4 lb./cu. Ft.). Sulphur in bulk form weighs 84 to 90 lb. per cu. Ft. Sulphur melts at approximately 240°F. to a straw coloured liquid which is quite viscous."

Jan 1, 1952

By G. M. Ritcey, S. H. Lucas

"On the north shore of the St. Lawrence River, in Quebec, are located orebodies of low-grade titaniferous magnetite. The Quebec Mining Exploration Company (SOQUEM), who have an interest in the deposits, believed that beneficiation of the could generate sufficient revenue to defray the mining costs and the costs of transporting the ore to a steel production facility. A joint research project of SOQUEM and CANMET investigated alkaline roasting of a magnetic concentrate, followed by leaching of the calcine and separation and recovery of Cr and V by solvent extraction. Aluminum was recovered by precipitation.The present paper describes the roast-leach bench-scale and pilot-plant work leading to the development of the optimum conditions f or the integrated process.A plant flowsheet was developed for the treatment of 5 x 106 tons of magnetic concentrate per annum. Estimates of capital and operating costs were made.Based on a recovery of approximately 90% V, 85% Cr and 75% AI, the total hydrometallurgical plant fixed capital costs, including mining, concentration and shipping, are estimated at $1.021 x 109; the operating costs are estimated at $131.92/ton concentrate. Annual revenue from the Na2CrO4.H2O, V2O5 and A12O3 produced is calculated to be $421 x 106.IntroductionThe Quebec Mining Exploration Company (SOQUEM) acquired in 1968 an interest in four titaniferous magnetite orebodies located in Eastern Quebec. 85 miles north of Mingan on the north shore of the St. Lawrence River. The Mingan deposit, with an estimated tonnage of one billion tons, has a reported average grade of 43% Fe, 6.3% Ti , 1.60% Cr, 0.19% V and 6.1% Al with minor amounts of nickel. SOQUEM, on the basis of previous bench-scale data, believed that the recovery of chromium, vanadium and alumina by alkaline roasting would generate sufficient revenue to defray the mining costs and the costs of transporting the ore to a steel production facility on the coast. One of the approaches selected by SOQUEM for beneficiation of the ore consisted of a combination of magnetic concentration followed by alkaline roasting of the calcine."

Jan 1, 1980

By N. Katsikaros, N. S. ‘ Yap, B. Adaszynski

"Cyanide is a well proven, effective lixiviant that has been utilised for centuries in gold extraction processes. Despite being used in close to 90% of gold processing plants, cyanide leaching is still being scrutinised due to its toxic nature. With governments tightening the regulations on cyanide management, and recently erected sites situated closer to community and environment, leach waste and tailings treatment has become increasingly important. Gekko Systems has worked with engineering companies and directly with gold producers to provide technical services and supply complete modular cyanide destruction (detox) systems for plants leaching both run-of-mine ore and high sulphide gravity and flotation concentrates. Although similar in principle, the different materials presented unique challenges in design and implementation. Similar to designing any section of a processing plant, the development of the cyanide destruction plant design began with laboratory test work to simulate the full scale operation. This paper focusses on the laboratory test work and how other critical factors such as geographical location, logistics, and local community play a role in the process design and construction. Two design and supply cases are discussed in this paper; one treating intensive cyanidation concentrate leach tails and one treating whole ore CIL tails. Although these plants both use the SO2/O2 process, each presented different challenges in laboratory testing and plant design, resulting in variations in final implementation including reagent choice, oxygen supply, and process control.INTRODUCTIONSince 1887, cyanide has played a large part in the beneficiation of gold from gold bearing ores. Cyanide is used to solubilise gold into solution, and is typically added in excess to maintain the leaching process. Some or all the excess cyanide can often be recovered and reused in the process however chemical destruction of cyanide is often necessary to manage cyanide levels in the tailings storage facility (TSF)."

Jan 1, 2016

By B. Das

"Computers have been used extensively in the mineral industry in exploration, reserves calculation, mining technology, mineral processing, etc. With respect to coal mining, there are also various applications for evaluating rock slope stability of open pits, design of open pits, underground operations, mine ventilation, ground control, data processing and management information, operations control and certain technological applications. Mine ventilation appears to be the field in underground coal mining touched on most; on the other hand, underground coal mining methods evaluation is represented only sparingly.It is therefore essential to review the status of the computer in underground coal mining methods evaluation in order to define its scope for further application. The paper discusses the roles of the mining engineer, programmer, computer operator and analyst as well as that of the computer. The important parameters will be identified and discussed along with their application for different underground coal mining methods, with their individual unit processes. Mainly, longwall face operations have been covered. Although many models have been of academic interest, they can be considered as important steps in a transition stage which will be followed by more practical applications for computers for underground coal mining method evaluations in the future. This calls for a coordinated effort from all concerned."

Jan 1, 1981

By Louis R. Bernier

Most systematic studies carried out on passive treatment systems incorporating the use of limestone drains, under aerobic or anaerobic conditions, essentially deal with the treatment of effluents from mines in the USA. A limestone drain typically comprises a trench filled with crushed limestone rocks surrounded by impervious materials. In the case of anoxic drains, the trench is generally isolated under a geomembrane liner covered with soil. Contaminated mine effluents flow by gravity towards these limestone drains where the passive treatment consists in bringing the carbonates into solution, thus increasing the pH and alkalinity. Factors to be considered in the design are: chemistry of the contaminated mining effluent ([metals, [Al], [sulfates], dissolved oxygen, acidity, pH), desired residence time, nature of the rock, grain size, density, void ratio and mass of the limestone rock used, alkalinity, life span and hydraulic behaviour of the drain. Certain secondary effects (saturation by sulfates, co-precipitation, adsorption) may either be beneficial (lowering the sulphate and metal load) or harmful (armoring the limestone rock and clogging of the drain). This paper gives a brief status report on the available knowledge on the use of limestone drains for passive treatment of mining effluents heavily loaded with metals. Examples given include the old Lorraine mine (Ni-Cu), Témiscamingue, where limestone and dolomite rock drains were installed in 1998 when a cover with capillary barrier effects was placed over the tailings site.

Nov 1, 2002

By W. H. MacLean

The Matagami district lies directly west of Chibougamau on the north side of the Abi tibi greens tone belt. Ores at Matagami are volcanogenic massive sulphides and occur in the dominantly rhyolitic Watson Lake group surrounding the Bell River Igneous Complex. Rhyolites and basalts of this group, and basalts of the overlying Wabassee group in the central part of the district, are tholeiitic; calc-alkaline Wabassee rocks occur in the western part. Massive sulphides occur associated with rhyolite domes that can be delineated by paleotopographic and isopach mapping. They are mainly distal deposits that formed over an extended period of time while several volcanic units were being deposited,

Jan 1, 1984

By A. McLean, Q. R. Yang, Y. D. Yang, G. F. Zhang, P. Wu

A considerable amount of waste slag from the pyrite roasting process is discharged every year. Recovery of iron from the waste slag is of great interest for comprehensive use of mineral resource, reduction of environment impact and improvement of economical benefit to related companies. The objectives of the present work are focused on: (1) Compare various procedures for recovery of iron from the waste slag and select a best procedure for industrial trial which is roasting of the waste slag under reducing condition followed by magnetic separation; (2) Investigate the optimum conditions for maximum recovery of iron from the waste slag. The experimental result shows that under the treatment condition found in this work about 36 to 40% of the iron oxide was recovered from the waste slag, where the iron content in the concentrate is 57%. The total recovery ratio of iron, up to 70%, from the waste slag was achieved. After the treatment, sulphur content in the waste slag was reduced significantly and gangue materials, such as SiO2, Al2O3 and TiO2, were reduced effectively.

Jan 1, 2011

By E. Czech

Hydrogen generated through aluminum-assisted water split reaction is a novel, efficient and environmentally friendly method. It has been found previously that the passivation of aluminum can be prevented in neutral (pH=7) or near neutral pH conditions in water by grinding aluminum with a catalyst, such as A12O3, SiO2 or SiC. Recently, the best results have been obtained by using water-soluble inorganic salts (WIS), ground with aluminum. The massive, rapid corrosion reaction of the Al-WIS system which takes place in regular tap (or marine, or ground) water can be utilized to produce hydrogen by aluminum-assisted water split reaction, in-situ, on-demand. The reaction offers clean, low-cost, environmentally benign and entirely recyclable technology for on-board on-demand hydrogen generation. Besides pure gaseous hydrogen, only pure solid aluminum hydroxides AlOOH or Al(OH)3 are formed as the reaction products. The hydrogen yield and Al-WIS reaction efficiency are high. From 1 g of mechanically alloyed aluminum powder, up to 1.25 liters of hydrogen were generated, i.e. efficiency up to 92% was achieved. The amount of hydrogen and hydrogen generation rate depend on various reaction parameters. The effect of chemistry and concentration of additives, water temperature, powder particle size and milling conditions on the reaction kinetics will be presented and the possible process mechanism will be discussed.

Jan 1, 2005