Search Documents

By C. A. Pickles, K. Mackowiak, D. Gajonera

"Shake-flask oxidation tests were performed on Red Dog mine waste to study the initial dissolution behaviours of lead, zinc, and iron. The conditions for accelerated acid generation in terms of Eh and pH were determined. Each mineral behaved distinctly, with galena dissolving first, followed by sphalerite, then pyrite, although there was some overlap in behaviour. Iron was not detected in solution until approximately day 40 and was present at low concentrations. The experimental conditions and the theoretical model results indicated the formation of iron oxyhydroxides at low weathering times and jarosite at longer times.RÉSUMÉ Des tests d’oxydation par agitation en flacon ont été effectués sur les déchets miniers de l’exploitation Red Dog afin d’étudier les comportements initiaux de dissolution du plomb, du zinc et du fer. Les conditions entraînant la production accélérée d’acide en termes d’eH (potentiel d’oxydoréduction) et de pH (potentiel d’hydrogène) ont été déterminées. Chaque minerai se comportait différemment ; la galène a été la première à se dissoudre, suivie de la sphalérite, puis de la pyrite, mais un certain chevauchement des comportements a été observé. La présence de fer en solution n’a été détectée qu’après environ 40 jours et ce, à de faibles concentrations. Les conditions expérimentales et les résultats du modèle théorique signalaient la formation d’oxyde-hydroxyde de fer sur de courtes périodes d’altération atmosphérique, et de jarosite sur des périodes plus longues."

Jan 1, 2017

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By N. Schreithofer, M. Aspiala, R. Serna

The novel attachment timer apparatus presented in this paper serves as a diagnostic tool that allows the detection of changes in bubble-particle attachment probability and therefore floatability caused by alterations in the chemical environment and particle properties. The apparatus consists of six identical capillaries where bubbles with defined size are produced simultaneously in a measurement chamber. The bubbles at the capillary tips are placed in contact with the submerged particle bed for specific time periods, controlled with the help of automatic actuators. The advantage of the instrument is that hundreds of bubble-particle contacts can be measured automatically within a short time period. Microscopic pictures of each measured bubble are taken while recording the movement of the bubble before, during and after contact with the solid particles. The recorded pictures can be used to determine the actual bubble size and its corresponding deviation, and to detect the attachment of particles. The attached particles are collected in a detachable chamber for subsequent characterization. Furthermore, the device is portable and can be taken to the mineral processing plants for quick evaluation of particle-bubble attachment efficiency with particles and process water sampled directly from real processes.

Jan 1, 2017

By Yi-Chun Lin

Mechanical/Electrical/Piping (MEP) systems, due to their complexity and diversity, are the most intricate part of building construction. This being the case, Combined Services Drawings (CSD) and Structure, Electric and Mechanic(SEM) drawings can ensure that all coordination issues are resolved prior to construction. Construction companies attempt to apply Building Information Modeling (BIM) to manage and integrate engineering information and solutions efficiently into the CSD and SEM processes to enhance the accuracy of design and the efficiency of review. There are several powerful commercial tools, such as Bentley Navigator, Autodesk Navisworks, and Tekla BIMsight, that can review the integrated BIM model and detect conflicts in systems, and allow planners to correct the conflict issues one at a time. However, for increasing numbers of conflicts, this may be inefficient, and requires them to be arranged in a list according to impact and seriousness before solving them. For this reason, this research implements a module for conflict impact assessment based on rule-based reasoning to classify and weigh conflict impact and seriousness, and highlight the conflicted objects in the BIM system in different colors depending on their conflict type and seriousness during the analysis. This system not only detects and lists possible conflicts and errors, but also sorts them according to the severity of impact and conflict type. Planners can effectively modify the BIM models according to these conflicts as they are listed and visualized in the BIM system. If these conflicts, such as pipeline interference and problems of insufficient space, can be avoided in the early stages of planning, it facilitates the achievement of project objectives in quality, scheduling, and cost.

Aug 1, 2013

By G. O. Oniyide, H. Yilmaz.

"This paper presents the result of the research done on the effect of temperature on the dilatancy of rocks from the Bushveld Igneous Complex (BIC), where the South African Platinum mines are located. The BIC has higher virgin rock temperature (VRT) than the gold mines of the ‘Witwatersrand Basin Complex’. If the platinum mines advance to ultra-deep levels as the gold mines, since the Merensky Reef has been reported to extend beyond 5km, then the virgin rock temperature at 5 km below surface would be approximately 140oC. Hence, there is a need for the investigation of rock behaviour at high temperatures. Five different rock types (norite, leuconorite, mottled anorthosite, pyroxenite and chromitite) were tested in a 2600 kN servo-controlled multi-purpose triaxial testing machine. The tests were done at a constant strain rate of 5 x 10-1 S-1 and a confining pressure of 10 MPa within temperature range of 20 °C (ambient temperature) to 140 °C. The results show a general strength reduction and increasing dilation angles with increasing temperatures. The results also demonstrate that dilation angle is close to the internal friction angle at lower temperatures; however, they are greater at higher temperatures.INTRODUCTIONMany challenges are faced with increasing depth of mining in underground mines. The most obvious are heat, in-situ stresses and those associated with logistics. Issues related to underground heat have mainly focused on the side effect of heat on workers' health, increasing production costs as a result of higher cost of ventilation. The effect of increasing temperature with increasing depth on the behavior of rock has not been given much consideration. Generally, gold mines in South Africa are deeper than the platinum mines but the latter have higher temperature gradient, which makes the platinum mines to be warmer at similar mining depths. Although the study of the effect temperature on the behaviour of rock can be beneficial to both gold and platinum mines, the focus of the research is limited to the platinum mines because of their higher temperature gradient. Donoghue (2004) stated that the virgin rock temperatures (VRT) and air temperatures increase with depth, due to the geothermal gradient and auto-compression, that is, compression of air by its own weight."

Jan 1, 2015

By R. Panchadhara, P. A. Gordon

"A non-local formulation of the classical continuum mechanics theory called peridynamics is used to study driven dynamic fractures in the near wellbore region. The controlled application of pressure on the inner walls of the borehole can create multiple fractures that initiate from the borehole and propagate radially outwards. The number of fractures and their final length is primarily controlled by the loading conditions and the in-situ stress state. It is the objective of this study to use a novel numerical technique called peridynamics to investigate: 1) the influence of loading conditions on the fracture pattern, and 2) the effect of in-situ stress anisotropy on fracture propagation. In peridynamics, the momentum equation from the classical theory of solid mechanics is replaced with the integro-differential momentum equation of peridynamics. As a result, discontinuities in the body, such as fractures, occur spontaneously. The material is represented by a continuum body with material points that interact non-locally with all other points within a specified distance. Fractures evolve using a damage evolution law, wherein, damage at any point is represented as the ratio of the number of broken bonds in the current configuration to the total number of bonds in the undeformed configuration.Simulations are performed on simplified test cases and the results are compared to relevant experimental and numerical studies found in the literature. It is shown that the loading rate significantly influences the number of fractures initiated from the borehole as well as their extent. Low loading rate produces fewer fractures, whereas, high loading rates produce longer and a greater number of fractures from the borehole. The numerical method successfully predicts the fracture pattern obtained from a wide range of loading conditions. Predictions also indicate that the resultant fractures are shorter when in-situ stress is applied. Numerical results show that the fracture extension is largest in the direction perpendicular to the minimum compressive stress for the range of loading rates used in this study."

Jan 1, 2015

By C. R. Hocott

"IntroductionRESEARCH in petroleum production consists primarily in investigations related to the drilling for and recovery of oil. As an organized activity of individual oil companies, production research is now 30 to 35 years old, and the petroleum industry may point with justifiable pride to the achievements of this third of a •century. Emphasis on research has grown through the years until at the present time many of the larger companies operating in the United States •have well-organized production research staffs.In addition to the efforts of the oil companies, significant research and development in petroleum production technology have been performed by oilfield service companies and others. Valuable contributions have been made through fundamental research carried on by the U. S. Bureau of Mines and by various colleges and universities, both in their own programmes and in programmes sponsored by industry, such as those of the American Petroleum Institute. However, the total effort of these groups is small when compared to the sum of the effort devoted to research by the individual .oil companies. In contrast to some industries which conduct the major portion of their research through co-operative, sponsored research at universities or research institutions, research by the petroleum industry is done predominantly by individual company research staffs. These industrial research groups have usually been organized in such a way as to provide liaison and co-ordination with operating technical staffs. In this way, the research groups are kept aware of the major problems confronting the operating departments and, correspondingly, the operating technical people •are able to keep informed on research activity and progress. This type of close contact generally results in prompt testing of research developments in actual operations."

Jan 1, 1953

By A. Roy, T. LeBel, P. Coursol, P. Lind

At the early stage of a mining project, small amounts of concentrates are available for testwork. For gold concentrate or ores containing significant arsenic levels, batch bench scale roasting is often unreliable, leading to highly variable gold recoveries to be used in the project’s financial justifications. With an appropriate bench scale unit using continuous feeding and residence time control for solid and gas phases, reliable numbers can be obtained at small scale with only a few hundred grams per test condition. This paper describes the development of a pilot fluid bed roasting unit by Kingston Process Metallurgy Inc. (KPM) to perform representative trials on gold concentrates containing arsenopyrite, arsenian pyrite and carbonaceous components. Calcines produced under different conditions were characterised by chemical analysis and electron microprobe; the calcine microstructure obtained is described. The most important parameter affecting gold recovery is oxygen content in the roasting atmosphere, with the lowest controlled oxygen level giving the highest gold recoveries. Higher local temperatures in the bed may cause the formation of molten glassy phases which can also reduce the gold recoveries significantly. The impact of roasting conditions in the two inch fluid bed is compared with commercial results obtained in full scale operation.

Jan 1, 2014

By K. Ski

Three series of membranes were prepared by blending polyvinylidene difluoride (PVDF) or poly(vinylidene difluoride-co-hexafluoropropylene) [P(VDF/HFP)] with sulfonated poly(ether ether ketone) (S-PEEK), sulfonated polysulfone (SPU), or sulfonated polystyrene, in order to develop novel PEM membranes suitable for melt processing. By means of incorporating fluorine-containing block copolymer into the blended system, acceptable proton conductivity and low water containing PEM materials were prepared. The effect of sulfonated poly([vinylidene difluoride-co¬hexafluoropropylene]-b-styrene) block copolymers as compatiblizers was investigated: conductivity was enhanced for S-PEEK/fluoropolymer blends. Microstructures for the blends were examined by transmission electron microscope (TEM) and scanning electron microscope (SEM).

Jan 1, 2005

By S. Parkash, A. J. Szladow

Vigorous agitation of suspensions of coking coals in water (or light mineral oils) will often result in catast rophic loss of caking properties. It is shown that this deterioration is not a consequence of oxidation of the coals (by dissolved oxygen), but that it can be qualitatively connected with internal "solid-state" reactions which appear to derive their activation energies from cavitation of the liquid.

Jan 1, 1971

By R L. Cheesman

An extensive Precambrian iron-formation lies about 2,000 ft. beneath post-Precambrian rocks in the Fort a Ia Corne Forest Reserve, south of Choiceland, Saskatchewan. The geology, deduced from limited drill results and from some geophysical observations, indicates that the deposit is a characteristic magnetite iron-formation, not uncommon in the exposed Precambrian of Saskatchewan, but also shows certain interesting features of faulting and pre-Paleozoic weathering which have given rise to a pre-served detrital deposit of hematite. The body is of ore grade and of sizeable proportions. T HIS paper is presented in order to set forth the interesting geological features of a Precambrian iron deposit located beneath the cover rocks of the Great Plains region and to comment upon the methods of discovery and interpretation of the nature of the body. The Choiceland iron deposit is located in the Fort a Ia Corne Provincial Forest Reserve, some 15 miles south of the town of Choiceland, Saskatchewan. Choiceland is

Jan 1, 1964

By F. Chiesa

The permanent mould process, which is a favoured process for producing premium quality aluminium casting, is rarely used to produce magnesium alloy parts. This may be attributed different factors such as: the reservation with which the automotive industry considers using magnesium in structural castings; also the relative hot shortness of most magnesium alloys when compared to aluminium A356/357 is another factor. A third reason stems from the fact that the "heat content" of magnesium is much less than that of aluminium, resulting in the difficulty, for a relatively slow process such as permanent mould (versus pressure die casting), to reach a mould dynamic equilibrium temperature sufficiently high to avoid premature freezing and misruns. The present work will address this problem by carrying out controlled cycling of a laboratory mould, poured with aluminium and magnesium alloys. The influence of insulation of the mould and artificial electric heating on the run-in mould temperature will be determined experimentally. A thermal model will be sought for these thermal devices that will allow to predict the thermal behaviour of moulds of different geometry before a single casting is poured. The model will be tested on an industrial casting in a workshop environment.

Jan 1, 2006

By Helen Shang, Jianjun He

In nickel and copper production, sulfur dioxide (SO2) is generated during mineral smelting. Emission of sulfur dioxide into the atmosphere causes serious health and environment issues. Sulfuric acid plants, which convert the harmful SO2 gas to commercially useful sulfuric acid product, ensures safe and environmentally sound smelter operations. The sulfuric acid plant is mainly composed of a SO2 to SO3 converter, a series of heat exchangers and SO3 absorption towers. The SO2 converter is crucial for minimizing SO2 emission in a smelter. In this paper, steady state and dynamic modelling are carried out for the converter using mole and energy conservations. Simulations are performed to investigate the effect of feed conditions on SO2 conversion. The developed model represents an important component for modelling the acid plant in a smelter and is expected to provide a fundamental tool for the future optimization and control development.

Jan 1, 2014

By H. C. Cooke

This paper will discuss two comparatively unrelated subjects; first, a general review of the advances made at the more important properties in the last year; and second, a statement of the conditions controlling the deposition of the copper ores in the Rouyn area, as determined by last summer's field work. FIRST PART Development has been very rapid since I stood before the Institute one year ago to discuss this same subject. Then, there were many properties on which gold had been discovered, any of which might develop into a mine. Further work has eliminated the most of them as possible mines, or at least has shown that before they can attain that status further discoveries must be made on them. Then, all gold veins held forth much the same promise; now the indications are that one particular type of gold vein is of greater prospective value than others. Then, all eyes were turned toward gold as the metal of prime economic importance; now copper has taken the centre of the stage, and gold is distinctly in the background.

Jan 1, 1926

By J. Lee

A monolithic caisson is one of the major structural components commonly used in the construction of docks, breakwaters, and container terminal quay walls. Since the structure of monolithic caissons is typical and somewhat simple, its design process is also typical and repetitive, but still time consuming. To reduce the total time and enhance productivity, we developed a parametric model in Revit to automatically generate a 3D model of a monolithic caisson. It is designed to generate the Revit model of a caisson with concrete body and reinforcing bars. The size of caisson, the number of reinforcing bars, and the space between reinforcing bars are automatically changed when users update parameters. This paper presents how we developed this parametric family in Revit for monolithic caisson design and how it would enhance its design process.

Aug 1, 2013

By Oliver Hall

WITH the friendly consent both of the Institution of Mining and Metallurgy, for whom this paper was written, and of the author, we had the pleasure of publishing Mr. Oliver Hall's paper on Mining at Noranda in our issue of last March and of having Mr. Hall present it at the Montreal Meeting. In the following pages we now report the discussion elicited by the paper at a meeting of the Institution in London on March 18th. The report is taken from the April, 1937, issue of the Bulletin of the Institution, to whom we again tender our thanks. THE PRESIDENT (MR. ROBERT ANNAN) said that this paper was, by arrangement with the Institution and the author, also being published by the Canadian Institute of Mining and Metallurgy for approximately simultaneous discussion. He was sorry that Mr. Oliver Hall could not be present to introduce it in person, for he was sure that the author would have had many more details to give about this most interesting mine. The paper contained a very useful account of mining operations, and personally he had been pleased to see the tri-dimensional projections of the orebody in Figs. 3 and S. It was a good illustration o the value of that method in presenting the form of an orebody such as this. While he had no desire to go into technical details, he wished to call attention to a remark in Mr. Hall's introduction, in dealing with the history of the mine and the principles on which it was run. The author had given an account of the early difficulties in solving geological problems, and later of the economic difficulties of seeing this mine through a period of intense depression in metal prices. He stated that it was clear that, to maintain income, tonnage must be increased, and, to maintain profits, costs must be decreased. It would be observed that there was no question of increasing the grade of ore. Then the author went on to say: 'Having set the house in order in the years of adversity, the higher price for gold is being used to mine to still lower limits and lengthen the life of the enterprise and the welfare of those dependent on it'.

Jan 1, 1937

By Dwayne D. Tannant

This paper presents a summary of results from a questionnaire sent to surface mines in western Canada seeking information on haul road design, construction, and maintenance. There has been a marked increase in the size of the trucks used over the last decade with some mines now using trucks with a payload capacity of 360mt. Consequentially, geometrical elements of haul roads, such as width, have been enlarged to accommodate larger trucks. Most haul roads are constructed on the basis of past experience without use of formal design procedures. With the introduction of larger haul trucks, problems related to rolling resistance, deterioration, and maintenance of the haul roads have become more important. This has lead to adoption of more rigorous design methods for roads at some mines, most notably for the oil sand mines operated by Syncrude Canada Ltd. A summary of the evolution of haul road designs implemented at Syncrude Canada Ltd. is presented.

May 1, 2001

By K. Dinh

The Ground Penetrating Radar (GPR) has been studied for a long time as a non-destructive evaluation (NDE) technology for inspection of concrete structures. Currently, the most widely used technique for interpreting GPR data of concrete bridge decks is the one that based on the amplitudes measured at various interfaces such as asphalt-concrete, top rebar, or slab bottom. The assumption behind this technique is that a sound concrete deck should have the same reflection amplitude at these interfaces while any low number would indicate some sign of deterioration. Unfortunately, this assumption is not completely valid in most cases. As a consequence, the reported test results usually do not reflect real condition of concrete bridge decks in question. The main goal of this paper is therefore twofold: (1) to discuss the limitations of the amplitude analysis method, and (2) to propose a new model that interprets GPR data of concrete bridge decks. The model methodology is based on the comparison of GPR A-scans between two inspections, using the so-called correlation analysis. The results, indicated by the correlation coefficients, are then employed to develop a contour map that estimates different levels of deterioration. The model is then implemented to a case study in order to illustrate its methodology.

Aug 1, 2013

By M. Hekmati1

SAG/AG mills have been most common choice in grinding circuits last decades. In the most cases, at the discharge of SAG/AG mills, a trommel screen is used that is equipped with baffles to provide appropriate residence time and improve separation efficiency. Using baffles, with the resultant maintenance requirements could lead to decrease in mill availability. In this research, an innovation in the structure of baffles of a trommel is presented. The results show that using new baffles led to 67% decrease in SAG mill downtime due to problems of baffles and 80% decrease in fine particles on recycle conveyor.

Jan 1, 2012

By R. C. Hartviksen, B. H. Boyum

"The Sherman Mine, Temagami, Ontario, is an iron ore pellet operation rated at one million tons per year capacity. Mining is done from three open pits in two bands of Keewatin iron-formation intercalated in a 'greenstone belt' thought to be part of the Archean 'Abitibi Belt'. The bands of iron-formation are tabular and steeply dipping, averaging 75 degrees. The principal ore mineral is magnetite.Blast holes, 1214 inches in diameter, are drilled on 28-foot centers, each hole being sampled and assayed for both total iron and magnetic iron. Concentration tests are made in the laboratory to determine the anticipated concentrate grade. Two classes of ore are recognized -'liberating' or 'refractory'. Blending is done on iron con-.tent, degree of ease of liberation (i.e. grain size) and chunkiness. The latter is important, as primary milling is done in autogenous mills. Actual daily mill results are compared with predicted grade from blast holes, exploration diamond drill holes and pit inspection. Hourly mill samples are analyzed by the X-Ray Fluorescent Analyzer, with emphasis on silica grade. In 1969, the pellet grade was improved from 7 .01 per cent silica natural to 5.50 per cent silica natural."

Jan 1, 1970