Search Documents

By R. Kaibyshev, I. Zuiko

"The effect of thermomechanical processing (TMP) including cold working by tension or rolling before aging on mechanical properties and a dispersion of secondary phase particles of an AA2519 alloy (Al–5.64Cu–0.33Mn–0.23Mg–0.15Zr–0.11Ti–0.09V–0.08Fe–0.01Si (wt. %)) was examined. It was shown that the use of tension to impart pre-strain =10% in the alloy provides the best combination of properties in peak aging condition of the material. The AA2519T87 alloy processed by tension exhibits the yield stress, ultimate tensile strength and elongation to failure of 425.4±2.4, 475±2.4, 12.1±0.4, respectively. The one pass rolling leads to -5% decreases in yield stress and –20% decreases in ductility. Dislocations serve as heterogeneous nucleation sites for ?'-phase precipitation. The positive effect of tension is attributed to the formation of more homogeneous dislocation structure, uniform distribution of ?'-phase particles with higher aspect ratio. Precipitation of the O–phase plates on {111}a habit plane was detected. In addition it was shown that the low angle boundaries are heterogeneous nucleation sites for ?' and O particles.INTRODUCTION Precipitation-hardened alloys are a commercially important group of the materials because their mechanical properties can be modified by treating and changing the microstructure. Age-hardenable aluminum alloys belonging to the Al–Cu–Mg system are widely used due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance attributed to the highly efficient strengthening by the ?'-phase (Palmer, StJohn, Nie, & Qian, 2017). An AA2519 alloy exhibiting superior mechanical properties among high-strength Al–Cu alloys (2XXX-serie) due to minor Mg additives. It is known that, in alloys with high Cu/Mg ratio (=5.6) the classic precipitation sequence (Palmer et al., 2017; Wang & Starink, 2005; Wang et al., 2010) of supersaturated solid solution (SSSS) decomposition occurs: SSSS ? GP zones (Al3Cu) ? ?? (Al3Cu) ? ?' (Al2Cu) ? ? (Al2Cu) (1)"

Jan 1, 2018

By Alex Matheson, Nick W. D. Massey, Peter T. Bobrowsky

Crowing pressures on aggregate resources include diminishing reserves, high transportation costs, sterilization and land use conflicts. In the absence of detailed resource knowledge for a particular region, aggregate resource potential maps provide the best "first approximation" regarding the surficial distribution of sand and gravel. The 1:50 000 scale Level Ill aggregate potential map integrates several important factors which influence the management of sand and gravel. Data used to generate this type of thematic map is readily available in most areas, fieldwork required is minimal, there is a logical quantitative evaluation of the data layers and integration is easily accomplished on a desktop PC-based platform. Also the aggregate potential map, with its focus on identifying areas of potential future aggregate exploitation as well as present inventory, provides a useful tool for the aggregate explorationist.

Jan 1, 2001

By Frank Arthur Forward

FRANK ARTHUR FORWARD was born in Ottawa and attended the University of Toronto, where he received a B.A.Sc. in chemical engineering in 1924. From 1924 to 1929, he was a smelter operator and research metallurgist with the Consolidated Mining and Smelting Company of Canada Ltd. (Cominco) at Trail, B.C. Moving to Australia in 1929, he was assistant smelter superintendent, Mount Isa Mines Ltd., Queensland, until 1934, when he returned to Canada, spend-ing one year as metallurgist with B.C.

Jan 1, 1970

By R. W. Thompkins

In order to evaluate the impact of air quality control on mine design, a few examples are given of cases in wh.ich ventilation has affected the economics of the total design problem. Principles for the drainage of gas contaminants are shown, and the contamination control problems created by differential pressures in complicated booster fan installations are discussed. The paper also deals with the use of advanced mathematics for solving some of the ventilation problems likely to be encountered.

Jan 1, 1967

By J. Sugai

Formability of extruded round AZ31 magnesium alloy tubes with different manganese concentrations was evaluated by performing bending tests and measuring strain along the length of the tubes during the bending process. It was found that an increase in the manganese content from 0.3 % to 0.7% did not exert any significant effect on the values of yield stress, elongation, or compression to fracture. However the hardness tended to increase and the UTS decreased. The compressive ductility was significantly lower than tensile ductility for all manganese concentrations. Consequently, the formability of tubes decreased, causing cracks in areas where compression strain occurred during bending. It was also found that a larger strain occurred in the latter half of the region along the length of tube between the clamp-end and the tube-positioning block. Within this region, alloy tubes with higher manganese concentrations, 0.5 and 0.7 %, there was a clear strain peak within the strain profile, while for the 0.3 % Mn alloy, a more uniform strain profile was exhibited, indicating a more uniform deformation. This was confirmed by microstructural analysis of the specimens.

Jan 1, 2006

By E. Thune, F. Stålesen, E. O. Stensholt, O. M. Dotterud, E. E. Henriksen, P. O. Ramsdal

"The development and commercial operation of the Falconbridge chlorine leach process have been described in papers in 1985 and 1987. Since this time, various process improvements have been implemented and the capacity of the Kristiansand refinery has been increased to 85 000 t/y Ni, 40 0000 t/y Cu and 4500 t/y Co. The focus has been on continuous improvements in productivity, the use of energy and other costs. Several environmental issues have also been eliminated or reduced since 1987. IntroductionThe first nickel refining operation in Kristiansand, Norway, started in 1910 based upon raw materials from Norwegian mines. In 1929, Falconbridge Nickel mines purchased the refinery to acquire information and the patent rights to the Hybinette refining process that was practised at the small Kristiansand refinery. Falconbridge ownership has now, for more than 70 years, provided a strong base regarding raw material supply, financial resources and technical support for further expansions and major technical improvements at the refinery.The main concepts of the new chlorine leach process were developed in the laboratories from 1966 to 1969 and the process was piloted from 1970 to 1972. The main stages in the commercial plant were started in the 1975 to 1981 period. After 1981, there have been a number of process modifications, plant expansions and improvements to operating practices. The developments up to 1988 have been described in previous publications (Stensholt et al., 1986, 1988).This paper presents an overview of the process and how it is practised at Falconbridge Nikkelverk AS (FNA) today and describes some of the main changes that have been implemented since 1988. During this time, the nickel capacity has been expanded from 54 000 t/y to 85 000 t/y and the cobalt capacity from 2000 t/y to 4500 t/y. The paper describes how these expansions were achieved together with continuous improvements in operating efficiency and also gives an overview of the main environmental concerns at the refinery."

Jan 1, 2001

By Ivor da Cunha

Ontario Mining Association (OMA) represents 57 members that are engaged in exploring, producing & processing mineral resources in an environmentally responsible manner. Conservation Bureau at the Ontario Power Authority (OPA) develops, coordinates and stimulates commitment to electricity conservation and demand management programs ? OMA selected compressed air optimization for high impact cost savings and energy efficiency potential ? Ontario Power Authority (OPA) provided $218k funding for $532k project ? Commenced summer 2006, Final Report June 2007 ? Three representative sites participating: ? Williams, CVRD Inco & FNX McCreedy ? Different levels of energy management ? Small, medium and large mining operations ? Different corporate practices and culture

May 1, 2007

By John F. Dougherty

Recently, there has been much debate as to the relevance of reporting financial results using the conventional accounting systems, which is based on historical costs, during a period of rapid inflation. In the following paragraphs , the symptoms, if not the causes, of inflation, its detrimental effect on the financial soundness of business in general and the financial reporting changes being advocated to overcome perceived weaknesses in the present financial reporting system in accounting for the effects of inflation will be reviewed. Finally, a course of action as a sound approach to the financial reporting problem will be recommended.

Jan 1, 1978

By A. Warczok

Smelting slags contain payable metals in a dissolved form and as mechanically entrained matte or metallic inclusions in the size range from 2 to 1000 µm. Slag cleaning requires reduction of magnetite and metal oxides and sedimentation of inclusions. Slag cleaning in an electric furnace is carried out in batch or semi-continuous mode. The strong trend for continuous slag cleaning generates the basic question about the optimal geometry of the electric furnace. Results of combined CFD, potential distribution and heat transfer modeling allowed for the determination of the fluid flow pattern and the temperature distribution in a classical, circular electric furnace as well as in a rectangular furnace. For the rectangular furnace, various length/width ratios and position of electrodes have been simulated. Analysis of key phenomena pointed out the advantages of the rectangular electric furnace over the circular furnace, particularly for continuous slag cleaning. Phenomena that have been analyzed were mass transfer, the rate of slag reduction, coalescence and settling of inclusions, all on the basis of the calculated slag flow pattern and the temperature distribution.

Jan 1, 2007

By S. Vézina

"Environmental issues have evolved considerably over the last two decades. The main contributing factors, to name a few, have been the changing values of modern societies, the globalization of trade and its linkage to environment, evolution and accessibility of information/ communication technologies, better educated populations, climate change, longrange transport of toxics, and the increasing influence of non-governmental organizations (NGOs) and multistakeholders.As well, environmental management of mining operations had to be realigned in order to meet these new realities and to respond to more elaborated regulations oriented towards sustainability. Environmental management systems (EMS) have been introduced not only to meet the assurance of conformance to regulations but also to prevent pollution and to apply the continuous improvement of mining processes. EMS models have been developed and certification to international standards (e.g. ISO 14 001) is a common practice.Globalization has imposed challenges and additional requirements to environmental management. Developing a mine in emerging countries implies dealing with international agencies, local communities, and a variety of government infrastructures to obtain a “license to operate.” This paper presents the structure of Cambior’s EMS and how it was adapted and implemented in the company’s operations in South America."

Jan 1, 2006

By F. P. Hassani, A. Hara, M. Momayez

To be competitive on the international market, the Canadian mining industry must reduce its costs, increase its productivity and maintain a high standard of safety. There is a great need today for improved methods that would allow the detection of geological structures in advance of mining to reduce dilution and the monitoring of underground structures to increase safety. This will facilitate planning for optimum exploitation of the mine and to increase production at lower costs. This paper discusses two examples of more efficient mine planning using new technologies such as Ground Probing Radar (GPR). In Kidd Creek mine, GPR technology was used at the 2500and 2600 levels to (1) monitor the stability of the sill pillar; (2) locate the presence of disseminated sulphide pockets in the sill pillar for extracting the mineral content; (3) monitor the stope backs and wall structures to evaluate the effect of on-time filling sequences; and (4)assess rockfill quality in terms of the presence of voids and fractures within the rockfilled areas. In the New Brunswick coal mine in Minto, GPR was used along with core log data to map and construct a 3D block of a section of the bench showing the relative position of different layers overlying the coal seam.

Jan 1, 1996

By A. R. Turner

AERIAL survey methods have made enormous technical advances and gained new recognition since World War II. Before enlarging on this statement and reviewing some of the uses of aerial survey in industrial development it is important to de-fine what is meant by "aerial survey". The subject will be discussed in the broadest sense and references will be made to the four sections that compose the overall field of surveying operations from the air. These are: 1. Aerial photography and photo-graphic mapping. 2. The use of airborne electronic instruments for geodetic distance measurement and the determination of ground elevations. 3. Airborne geophysical surveying. 4. The extraction of qualitative and quantitative information from aerial photographs through the processes of "reading", analysis and interpretation. Many sciences and techniques are combined in aerial survey operations. The tools of the business include aircraft, finely engineered cameras, elaborate film processing and printing equipment, ground survey instruments, precision stereo-plotting instruments, map -

Jan 1, 1961

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012

By Lewis Finch

Oil and .gas reservoirs exist under pressure within the pore spaces of rock structures or traps. Wells are drilled to produce these reservoirs. Under primary operation, the natural energy of expanding fluids in and adjacent to the reservoir forces or drives oil and gas to the wells. There are three basic sources of energy: dissolved gas, water, and gas cap. Typical recovery by primary methods is only 10 to 25 per cent of the oil in place for the dissolved gas drive but is generally higher for the others. Secondary recovery involves the injection of water or gas to supplement natural energy, thereby increasing recovery over that obtainable by primary operation alone. In many cases ultimate recovery with secondary methods is 1.2 to 2.0 times the expected primary recovery. The type programme adaptable in a field depends on its 'primary performance and on certain reservoir characteristics. In the United States, application of secondary recovery methods is becoming increasingly important. About 22 per cent of United States oil production now comes from fields in which injection projects are operating. In 1953, nearly 1.4 million barrels of oil daily came from such fields, more than double the amount in the early 40's. Ultimate primary recovery from known pools is estimated at roughly 73 billion barrels. Secondary recovery projects already in operation will increase this to almost 80 billion, an increase of almost 10 per cent. Unitized secondary recovery projects have been very successful. From unitized projects alone, industry reserves of oil in the United States have been increased by 3 1/2 billion barrels. In Canada, secondary recovery has not been so wide spread mainly because D-3 reef reservoirs which have held the major reserves are under water drive. However, appreciable amounts of water are being injected in the Redwater D-3, Leduc D-2 and Joarcum Viking reservoirs, and gas in the Golden Spike D-3. In both countries, possible achievements in increased recovery through secondary recovery methods now in use and by new ones which may be developed through research and field trial are a challenge to the scientist and the industry.

Jan 1, 1956

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

By D. A. Barr

"Most of the lode and placer gold production in the Canadian Cordillera has been derived from mines and placers in the Intermontane and Omineca belts. Gold has been produced from rocks of Precambrian to Eocene age, but the preferred host environment contains Upper Paleozoic to Upper Jurassic eugeosynclinal or arc-type sedimentary and volcanic rocks adjacent to plutonic complexes which have a wide variety in both size and composition. Auriferous quartz lodes occur in fissures and shear zones which are commonly subsidiary to strong fault zones. In common with most vein-type deposits, structural complexities are an essential part of the mine environment.Gold production from the Canadian Cordillera to the end of 1978 totals 35.0 million ounces, of which 47 per cent has been produced from placer mining, principally in the Klondike and Cariboo districts. The balance has been derived from lode gold (80 per cent) and base metal (20 per cent) mines.Gold reserves in producing mines and deposits committed for production as of January 1, 1978 were 87.4 tons, or 21.6 per cent of total Canadian gold reserves contained in all types of deposits. Although more than 100 lode mines have operated in the Canadian Cordillera since the turn of the last century, over 75 per cent of the lode gold produced by 1978 was recovered from five mining camps, namely the Rossland, Hedley, Bridge River, Premier and Barkerville.The average grade of the principal producers in these camps was about 0.45 ounce of gold per ton. Individual camps yielded from 3 to 8 million tons during their operating lives, which varied from 28 to 43 years. The last of these mines ceased operating in 1971.Most of the total lode gold production has been derived from quartz veins, frequently with associated carbonate and ankerite, occupying fractured and faulted zones in Mesozoic volcanic and sedimentary rocks closely associated with a variety of intrusions. A review of the literature suggests that several deposits may have evolved by remobilization of ore constituents from earlier concordant gold-bearing formations. The principal metallic minerals in the deposits are native gold, electrum, tellurides, pyrite, arsenopyrite, pyrrhotite, sphalerite, galena and chalcopyrite.As the mineralogy suggests, many of the Cordilleran lode gold deposits have yielded important co-products or byproducts, including silver, copper, lead, zinc, cadmium and tungsten. Significant by-product gold production has also been derived from porphyry copper, volcanogenic, replacement and pyrometasomatic deposits, particularly in recent years.No major lode gold discovery has been made in the past 67 years, although little exploration activity for gold has taken place during the last 30 years. Several relatively small lode gold and gold replacement deposits have been discovered in recent years, either serendipitously (Chappelle) or on very low initial budgets (Northair and Carolin). Based on well-established precedents, one or more of these may eventually be developed into a large mine.A detailed study of the Canadian Cordillera gold deposits based on recent genetic models could prove rewarding, not only in up-dating information on their origin and depositional characteristics, but in stimulating the search for undiscovered gold deposits, in the Cordillera and other parts of Canada."

Jan 1, 1980

By Morgan Schauerte, Laura Raimondi, Mariel Palomeque

Executives in the mining industry are facing dramatically changing market expectations on reporting and transparency regarding the environmental and social impacts of projects, supply chains and products. Companies increasingly need to disclose the governance procedures they have in place to ensure communities, investors, employees, and Indigenous partners are effectively managing social and environmental risks. These disclosure requirements begin during exploration and carry through to all stages along the project life cycle. This type of environmental, social and governance (ESG) disclosure is referred to as ESG performance by the investment community. ESG is not a new concept, and it builds on and is intertwined with many concepts such as corporate sustainability, corporate social responsibility, eco-efficiency, triple bottom line thinking, life cycle management and many others. This paper will explore how mining companies can develop a credible ESG governance approach and strategy that will reduce risk, open opportunities, and create value. This paper will summarise ESG trends and drivers, discuss the economics and investors’ perspective towards ESG, and outline leading ESG standards and guidelines of interest to investors, regulators, communities and other stakeholders. Linkage of ESG to global sustainability efforts such the United Nations Sustainable Development Goals and Global Compact will also be addressed.

Jan 1, 2023

By Curtin University Western Australian School Mines

"Curtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. Recently the model has been upgraded to include an integrated liberation-leach modelling (ILLM) approach which can be used to evaluate the impact of various process parameters (such as grind size, bleed to gravity etc.) and circuit configurations on leach-adsorption circuit behaviour and overall plant gold recovery. A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach, which is implemented online for the modelling of gold operations. The model structure, modelling approach, and some scenarios are discussed.INTRODUCTIONCurtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. The model has recently been upgraded to include an integrated liberation-leach modelling (ILLM) approach. The ILLM approach provides the means to evaluate the impact of the gravity recoverable gold (GRG) characteristics of the ore (GRG content and liberation behaviour), various process parameters (such as grind size, bleed to gravity, etc.) and circuit configurations on the gravity gold recovery, leachadsorption circuit behaviour and overall plant gold recovery.A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach. The data required for the ILLM calibration can be obtained directly from the 3 stage GRG test, leach tests and size-by-assay analysis of the 3 stage GRG test products, and leach test products.This paper describes the ore characterisation methodology, model structure, modelling approach, and the application of the ILLM."

Jan 1, 2016

By H. Lazreg

This paper presents an evaluation of surface resistivity techniques as a tool for delineating salt-water intrusion in Shippegan, N.B. The study consisted of resistivity profiling, resistivity soundings and a limited number of induced polarization soundings in selected areas in the Province of New Brunwick. The results from resistivity profiling indicate that when seawater intrusion occurs in a sandstone formation the resistivity contrast is sufficiently large to allow a precise delineation of the intrusion. A formula is then derived to convert resistivity values to chloride concentration in the "cone of intrusion". The results from resistivity soundings showed that shaly formations may have resistivities as low as seawater-contaminated sandstone. An indeterminacy has resulted from this resistivity overlap. A limited number of IP soundings were performed in an effort to resolve it. The results showed that IP can be of appreciable help in resistivity interpretation.

Jan 1, 1972

By R. P. Charbonnier

"To understand the operation of jigs and other separating processes based on differences in gravity, it is desirable to analyse the motion of various particles in given media under specific conditions. A summary of the earlier theories shows that they lead to unsatisfactory or excessively complicated formulae in cases such as coal jigging. By adopting a simplified theory of the motion of particles in a fluid, the size and duration of the initial accelerated motion of a particle falling in hindered settling can be calculated. Based on this mathematical analysis, examples referring to actual coal jigging practice show that it is desirable to prolong and/or repeat, as frequently as possible, the optimum conditions corresponding to an effective acceleration of the particles. The separation is then obtained according to gravity rather than to particle dimensions, as would be the case if the velocity of the particles• were allowed to approach its terminal value. To achieve this gravity separation, it is suggested that the suction phase of the jigging cycle be artificially prolonged and the frequency of pulsations increased as much as possible for washing the coals of smaller sizes."

Jan 1, 1959