Search Documents

By D. F. VanDine, H. George

"The possibility of spoil pile failure at the Kara Kara bauxite strip mine, Guyana, South America, is of major concern to the mine operators. The current mining technique requires the continuous operation of an 11 ms bucket capacity walking dragline on top of 18 metres of freshly spoiled uncompacted overburden material consisting of varying mixtures of kaolinitic clay and quartzitic sand. A field biased geotechnical study of undisturbed overburden and corresponding spoiled material has identified site-specific, non-linear correlations between vane shear strength, standard penetration resistance and spoil pile composition. Readily available geological exploration borehole logs has enabled a composite clay isopach map of the entire mining property to be drawn and critical areas to be zoned according to expected slope stability. Stability has been assessed using simple hand calculation techniques. Use of the resulting stability map provides the mine operators with a means of forecasting the need for appropriate preventative measures at varying stages of mine development, throughout the life of the mine.A similar investigation procedure could be employed at many presently operating and future strip mines.IntroductionThe Kara Kara bauxite stripe mine is located at Linden within the bauxite belt of Guyana in South America. The mining property covers a total area of 88 hectares of flat to gently sloping ground of which some forty per cent is being actively mined or being preparatorily stripped of overburden, prior to eventual mining (George and Gordon, 1979). The regional climate is tropic and humid. Temperatures vary from 16°C to 38°C and yearly rainfall averages 2600 mm, with at least 55 per cent of this precipitation occurring during the 'wet season' months of May to July and December to January."

Jan 1, 1983

By D. C. Brady

"Within six months from award of a project management contract, Les Mines Dumagami Limitée, Cadillac, Quebec, was operating its new hoisting facility. This was accomplished with less than a six-week shutdown of mine production while still maintaining shaft access for underground maintenance.The work involved installing a refurbished /3.5 ft diameter double drum hoist, replacing a timber headframe with a newsteel headframe, increasing the ore bin capacity from 500tons to 1000 tons, constructing a new substation, and upgrading related facilities.This paper describes the work and methods used by various contractors, Les Mines Dumagami Limitée and J.S. Redpath Mining Consultants Limited to bring this project to a successful completion. It discusses the history of the project from proposal stage through to the design, procurement, scheduling, and construction management. The paper also comments on problems that were encountered and the methods used to overcome them.IntroductionThe Donald J. Laronde Mine of Les Mines Dumagami Limitée (Dumagarni), a gold and copper producer, is located in northwestern Quebec, approximately half way between Val d'Or and Rouyn. The mine started production in the spring of 1988 and the first gold bar was poured in June 1988.Following a request by Dumagami, on February 22, 1989, J.S. Redpath Mining Consultants Limited(Redpath) delivered a proposal to increase hoisting capabilities from 1500 tpd to a minimum of 2500tpd. Although various concepts were considered, Redpath proposed a new hoist house along the same shaft axis as the existing hoist, and located on the site of the existing substation. They would then provide a new substation, replace the headframe with a largersteel structure , gain extra storage capacities by increasing the bin heights, and raising the roof of the bin house accordingly.Although underground mining would have to be stopped for a month, the mill production would be maintained by feed from Dumagami's open pit.Figure 1 shows the original plant layout and Figure 2 represents the general arrangement after the project was completed . Table 1 compares the original hoisting facilities to the new facilities.On March 2, Dumagami awarded Redpath a contract that included preliminary engineering, detailed engineering, procurement and contract administration, and later added construction management. The preliminary engineering refined the initialconcept, selected major equipment, and prepared schedules and capital cost estimates for the total project."

Jan 1, 1991

By J. R. Morris, A. E. Ball, G. W. Kuzyk

"AECL Research has constructed an underground laboratory for the research and development required for the Canadian Nuclear Fuel Waste Management Program. The experimental program in the laboratory will contribute to the assessment of the feasibility and safety of nuclear fuel waste disposal deep in stable plutonic rock.In 1988, AECL extended the shaft of the Underground Research Laboratory (URL) from the existing 255 m depth to a depth of 443 m in cooperation with the United States Department of Energy (USDOE). The project, which involved carrying out research activities while excavation and construction work was in progress, required careful planning. To accommodate the research programs, full-face blasting with a burn cut was used to advance the shaft. Existing facilities at the URL had to be modified to accommodate an expanded underground facility at a new depth. This paper discusses the design criteria, shaft-sinking methods and approaches used to accommodate the research work during this shaft extension project.IntroductionThe Underground Research Laboratory (URL), a major geotechnical research facility, has been developed by AECL Research, 120 km northeast of Winnipeg, Manitoba. The URL is part of the Canadian Nuclear Fuel Waste Management Program (CNFWMP), which is assessing the concept of nuclear fuel waste disposal in a vault deep in stable plutonic rock of the Canadian Shield (Hancox, 1986). The URL provides a representative environment to conduct a wide variety of geotechnical research relevant to nuclear waste disposal. Extensive characterization and monitoring programs were carried out prior to construction and will continue during operation. The operating phase experiments began in 1989 and will continue until the year 2CXXl (Simmons, 1990). Figure I shows the present extent of the URL facilities and the proposed future development."

Jan 1, 1991

By R. Sage, N. Rillette, M. D. Everell, G. Herget

"CANMET has been operating as a Government Technology Centre for two years. Many of CANMET's programs involve long-term research and require special expertise, often available at Canadian universities. CANMET's involvement with universities ranges from research grants and contracts to exchanges of scientists and joint use of research facililies. Examples of CANMET - university cooperation in mining are presented. IntroductionIn the last two years or so CANMET has undergone a significant metamorphosis, resulting in greater emphasis on applied research to enhance Canada's industrial capability. CANMET's new mandate is reflected in the types of projects undertaken and their categorization, (Fig . I). Emphasis is being placed on two project categories: strategic R&D, to enable CANMET to serve the changing technological needs of the industry; and incrernental R&D, to serve the more immediate industry needs through modifications to existing technologies and knowledge. The balance of CANMET's e ffor t is devoted to providing Mandated and Specialized Services, and to Exploratory Research.CANMET interaction with universities can involve one of several available vehicles : contracts, research grants, exchanges of scientists , student employment and nomination of professors on CANMET's advisory council. Instances of key university technical support to CANMET mining projects are highlighted."

Jan 1, 1990

By A. R. Farkoosh, K. Korgiopoulos, McGill University, O. Rodop, L. A. Villegas Armenta

"New generation of Al-Mg-Si alloys with thermally stable dispersoids that prevent recrystallization and grain growth during hot deformation are currently used in automotive components requiring good formability. Alloy chemistry controls the phase formation especially age-hardening precipitates, dispersoids, and primary intermetallic which have pronounced effect on grain structure, strength and formability. In this work, thermodynamic calculations have been used to predict the effects of varying levels of Si (0.5-1.5wt%), Mg (0.5-1.5wt%) and Mn (0.1-2.5wt%) on phase selection. Thermodynamic calculations have been performed in equilibrium and non-equilibrium conditions via the FactSage™ software using the FTlite database. Selected compositions have been cast, heat treated, extruded and characterized through scanning electron microscopy with energy dispersive spectroscopy and electron channeling contrast imaging techniques. The calculations showed that at the hot deformation temperature of ~540 oC, exceeding certain Mg and Si levels would lead to retained *-Mg2Si intermetallics and Si particles at the grain boundaries in addition to a-Al-(Mn,Fe)-Si. It was found that retained *-Mg2Si phase which adversely affects formability can be avoided for Si+2Mg levels lower than 2.3wt%. FactSage calculations also showed that increasing Mn from 0.5wt% to 1wt% leads to an increase in the amount of dispersoids (from 1wt% to 2wt%) that can potentially slow down recrystallization and grain growth during hot deformation and improve formability. Calculations at room temperature also show that for an alloy with 0.7wt% Mg, excess Si beyond 0.7 wt% promotes the precipitation of Si clusters in the Al matrix that accelerate natural age-hardening. Results were confirmed by experimental investigation.INTRODUCTIONAluminum alloy 6082 (Al-Mg-Si) is used in the automotive industry because of its high strength, and good weldability (I. J. Polmear, 2006). The alloy is age-hardenable through the precipitation of ß-Mg2Si and its precursors, and the recrystallization is usually inhibited by Mn- and Cr-containing dispersoids formed through high temperature heat treatments (I. Polmear & Couper, 1988). However, it is known that minor changes in alloy chemistry (Mg/Si ratio) can have significant influences on the ductility and formability of these alloys by altering phase selection and the resultant microstructure (Gupta, Lloyd, & Court, 2001; McQueen & Celliers, 1997; Zajac, Hutchinson, Johansson, & Gullman, 1994). For automotive applications where wrought alloys (usually extrusions) are cold-formed to produce suspension components, the chemistry of the alloys and the extruded structure are of crucial importance as they determine the formability at room temperature (Asensio-Lozano, Suárez-Peña, & Vander Voort, 2014). In this study, thermodynamic calculations along with experimental investigations were carried out on the Al-Mg-Si system to understand their phase formation and precipitation hardening as a function of alloy composition."

Jan 1, 2016

By Geo. E. Cole

A GREAT deal of time and energy is now being devoted to the study of post-war reconstruction and rehabilitation, in spite of the fact that as yet we have not won the war in which we are presently engaged. If you feel that the study of post-war problems takes our thought away from the problem immediately before us, you may well query, "Well! What has all that to do with winning the war, our most urgent problem today?" The answer has been given by Principal James of McGill University, Chairman of the Cabinet Committee on Reconstruction: "Reconstruction is something which must be thought of in advance, partly for the purpose of recognizing exactly the influence of war-time activities, controls, and regulations on the post-war Canadian scene. Many people are acutely interested in this great problem. It is not that they are not interested in the war itself, or epochal events that are taking place from day to day. They have a vision of that future which they hope will be Canada's, and this vision inspires them to even greater efforts at the present time". The trend of events would indicate that changes, economic and industrial, after this war will be greatly out of line with those that followed previous wars in history, for the present struggle has involved every nation in the world. In the peace that will come, every engineer will have a task in bringing the most desirable order out of the most distressing chaos. We certainly are living in a changing world; we are witnessing geo-graphical and economic readjustments that no other generation in world's history has ever witnessed. And there is an opinion gaining strength in our Dominion, as in other lands, that after this war we shall live in a world in which our process of thinking and our very way of life will have to undergo drastic changes to cope with the new order of things. Sadly our world of today has had to revise the sublime vision that nation shall not lift up sword against nation, while salvage operations continue to beat ploughshares into tanks and the peaceful pruning-hook into a weapon for the deviltry of the commando.

Jan 1, 1943

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By Miguel A. Cuba

Resource models are generally constructed using data of different types and/or from different sources. A common issue is the consistency of scale in the information that often leads to a requirement to composite the data prior to model construction. For the purposes of mine planning, development and/or resource assessment, this model may then be upscaled to a relevant selective mining unit. It is well established that the geostatistical parameters for resource model construction is scale dependent. In particular, the volume variance of integrating these various scales has a direct impact on the variogram that should be used in model construction and/or the assessment of volume variance relations as it affects resource estimation. The scaling laws are a set of guidelines that detail how the variogram should change as a result of a change in the volume; these laws are empirically derived and involve some simplifying assumptions, not the least of which is an assumption of shape invariance in the variogram structure. An alternative approach was proposed to directly upscale the variogram via numerical integration, which demonstrates that the assumption of shape invariance is not required and we can directly access the new variogram shape given any volume of interest. This paper compares these two different approaches to variogram upscaling by considering two applications: the first corresponds to a 2D synthetic case and the second looks at a 3D case with data from a porphyry copper deposit. The simulation studies in these cases show that the direct upscaling approach performs better than the scaling laws in fitting the average experimental variogram values at any block size. This is based on a mean absolute error criterion. Moreover, it is also shown that with an increase in the block size, direct variogram upscaling significantly outperforms the scaling laws approach.

Oct 1, 2009

By J. S. Stewart

THIS paper was prompted by a persistent demand for what information we have that will throw light on the oil and gas possibilities of the Maritime Provinces. The problems involved were made familiar to the writer during three seasons of field work in New Brunswick and Nova Scotia. The reasons for renewed interest are: (1) In many parts of that region, the surface is underlain by a thick series of unaltered sedimentary rocks. (2) Oil seepages occur, and oil in commercial quantity has been exploited' near Moncton, New Brunswick, for many years. (3) In recent years, a new method of attack has been developed toward the finding of stratigraphic traps. This method is based on a detailed study of the geological history of the region, as revealed in surface outcrops and samples from deep wells. The well samples show the lateral variation of strata, far from any possible surface outcrop of the same beds. Sufficient work has now been done in the Maritime Provinces to reveal the broad features of the geological history and the character and distribution of the various rock formations. Comparatively little deep drilling has been done in this region, but the holes are widely scattered and the samples from them have added much to the information obtained from the numerous outcrops of bed-rock. The following discussion gives a summary of available information that has a bearing on the subject.

Jan 1, 1943

By Y. Hayashi, A. Fuwa

To analyze zinc vaporization kinetics of zinc smelting slag in the ISP furnace, reduction reaction rate of zinc oxide from ZnO-FeOx-CaO-SiO2 slag system with CO-CO2-Ar gas mixtures has been measured by a therm o-gravim etric apparatus at various ZnO content, Pco, and temperature. The reduction rate was measured under a chemical reaction control in the initial three minutes where surface zinc content can be assumed constant. Through the reaction rate dependency analysis on ZnO contents, Pco and temperature, discussion has been made on its reaction mechanistic information in terms of rate coefficient, adsorption/desorption mechanism and activation energy.

Jan 1, 2008

By M. M. Helm

Samples sourced from the Goldstrike property in Nevada USA, have been evaluated in terms of their preg-robbing capacity and the physical structure of the graphitic carbon component in the carbonaceous gold ore. The study highlights a wide range in preg-robbing capacity between samples collected from the Betze-Post open pit and Rodeo underground mine. The physical structure of the graphitic carbon was assessed using Raman spectroscopy, and is found to play an important role in influencing preg-robbing behaviour. Differences observed in the physical structure of graphitic carbon are thought to be the result of hydrothermal events that occurred at Goldstrike.

Jan 1, 2011

By Dale L. McKinnon, Jean-Pierre Farant

"Dust collectors are used to reduce airborne dust levels generated during crushing at a mining operation and their adequate maintenance is required to ensure effective control of health and safety hazards associated with dusty conditions. Although the pitot traverse technique is commonly employed to balance these dust collectors, the use of an alternative-the equilibrium concentration tracer gas method-is proposed in this paper. This method, which uses sulphur hexafluoride as a tracer gas, can be used to balance airflows in dust collectors and to determine hood collection efficiency accurately and effectively. This technique also reduces some of the errors inherent to pitot tube measurements. IntroductionIndustrial dust collectors are used to reduce dust genera ted by processes like cru shin g, and these must be periodically checked and balanced to ensure continuing effective control of health and safety hazards associated with dusty conditions.To date, the pitot tub e traverse technique has been commonly used to balance air flows in dust collectors. However, this technique is both time -consuming and cumbersome. The equilibrium concentration tracer gas method, described in this paper, is proposed as a viable alternative as it is faster, more reliable, and amenable to automation. The use of tracer gases for such task s is not new. This approach has been used in a variety of mining situations to determine volumetric flow rates in underground openings, leak age through mine stoppings, the effectiveness of face ventilation, pollution migration patterns, mine air recirculation rates, and rock porosity."

Jan 1, 1986

By H. K. Taylor

"As a mining engineer with over 50 years' experience in underground operations and mine planning, I appreciate the enormous amount of work that went into the paper; and despite an imbalance between geology-geostatistics and the profit-earning actions of mining and treating (possibly because of sponsorship only by the Geological Society), I agree with probably 85% of the detail. But the paper fails to build on its own sound foundations and, like many predecessors, drifts instead into idealism. Even the starting quotation from the US SEC Form S-18 is little more than a platitude. An American consultant (l) has observed: ""an evaluation that accepts ore reserves as guaranteed because their definition meets SEC criteria is an invitation to disaster"".Idealism enshrines at least two myths that have bedevilled definition over the last several decades. The first is that the only purpose of 'ore reserves' is to promise successful new mines, and that 'ore reserves' must necessarily follow feasibility studies.In practice, the identification of what is likely to be mined if a mine is started must often be done on broad economics long before the feasibility study, and there may be only little later flexibility. The second myth is that there can be a perfect deposit with a simple exploration-appraisal-development sequence (the paper's Figure 2) against which all inferiors can be matched. If the field of definition be regarded as a pyramid, the quest for perfection and the imposition of rigid promises upon the terms 'ore' and 'reserves' drive definitions so near the apex (or the bottom right corner of Figure I, if preferred) that little is left to define. The process is reminiscent of the legendary super-medicine, the one so powerful that the patient had to be in perfect health to take it!"

Jan 1, 1992

By M. N. Collison

"In 1960, with the opening of the Chisel Lake mine near Snow Lake, Manitoba, the Hudson Bay Mining and Smelting Co., Limited, commenced a new phase in their mining operation -that of bringing ore to Flin Flon over 100 miles of railroad.The schedule of operations required to accomplish this, together with an outline of some of the problems of handling ore at 40° and 50,0 below zero, are discussed. The facilities required to thaw and unload from twenty to fifty cars per working day are also described."

Jan 1, 1966

By G. G. Bowser

Introduction Flame shots are of very infrequent occurrence in the coal mines of Nova Scotia. Probably not more than one is recorded in three months. Many shot-firers have never experienced one, and many never will. As a consequence, although all such occurrences are very carefully investigated, information concerning the cause of flame shots is somewhat meagre. In the course of the years, however, something has been learned of the practices and conditions that are responsible for them. During the past ten? years, over seventeen million shots were fired in the coal mines of Nova Scotia and only fifty-two faulty shots were reported or investigated during that time. In thirty-nine of these, flames were reported; in five, sparks only; and in eight, smoke only. In eight of these occurrences, unburned explosive was found after firing. In one of these eight, flame was seen in the back part of the hole, and an accompanying hissing sound pointed to burning explosive. In four of them, there was no evidence that gas was not ignited. All samples of explosives from these faulty shots which were submitted for analysis were found to be normal, except two, in 1937, which contained excessive moisture. These two samples were from two following shots in the same room on the same day. The initial cause of trouble with all eight shots was one or several of the following: explosives in poor condition, separation of cartridges, incorrect priming, shot hole in poor condition or not properly cleaned. In the case of sixteen or seventeen of the thirty-nine shots which flamed, data are insufficient for conclusions to be drawn as to the cause of the flame.

Jan 1, 1947

By C. S. Touchard, F. Bourgeois, L. Cassayre, Julcour-Lebigue C.

Developing a hydrometallurgical process that can overcome the refractory nature of chalcopyrite (CuFeS2) to leaching still eludes the minerals industry, despite major research efforts spanning decades. The several leaching experiments of this ore in sulfuric acid tend toward the same conclusion that the precipitation of elemental sulfur or iron containing species are the main dissolution inhibitors. Describing both the electrolyte composition and the various solid phases in equilibrium for the Fe-H2SO4-H2O system is essential to overcome this issue and to find an operating window. According to the thermodynamic models and to the thermodynamic data, we demonstrate, in this study, the need to use the Specific ion Interactive Theory (SIT) model to describe complex electrolytic systems through a limited number of parameters. Hence, the binary interactions for our case study have to be defined and estimated. This work develops a methodology to determine these parameters of the SIT model up to 90°C and an acid concentration of 1 mol/kg from published data for H2SO4-H2O and Fe(II)-H2SO4-H2O sub-systems or from new experimental data for the Fe(III)-H2SO4-H2O one. This method will eventually be applied to copper systems to lead to a thermodynamic description of the complete CuFeS2-H2SO4-H2O system. INTRODUCTION A leaching process consists in the dissolution of a solid phase into an aqueous medium in order to extract compounds of interest. It is a key step in the hydrometallurgical processes used in the primary production and recycling of metal components. One of the main leaching issues is the formation of passivating layers on the surface of solid particles, whose consequence is a partial or total hindrance of the dissolution. The leaching of chalcopyrite (CuFeS2) in sulfuric acid is a prime example. No industrial solution for the atmospheric pressure leaching of this ore has been developed to date because of passivation phenomena caused by the formation of elemental sulfur or iron-containing precipitates on the surface of the particles (Li, Kawashima, Li, Chandra, & Gerson, 2013). In the 1970s, the Pourbaix diagrams established for the Cu-Fe-S-H2O system at 25°C for low concentrated solutions (Garrels & Christ, 1965; Peters, 1976) agreed that copper and iron are fully dissolved at high potential and in acidic medium (pH < 4). However, they neglected the many stable solid phases that can form in these conditions. In addition, the Pourbaix diagrams of chalcopyrite in water, calculated with two recent databases (FactPS and Thermoddem 2017) associated to FactSage and PhreeqC softwares respectively, show large discrepancies at 75°C (Figure 1). Indeed, at high potential, FactSage predicts the formation of goethite FeOOH at a pH value of 1, while PhreeqC predicts the formation of jarosite (H3O)[Fe3(SO4)2(OH)6] for pH greater than 2.5.

Jan 1, 2019

By Robert B. Parsons

"This month, Tax Notes focuses on two features which can potentially ""dress up"" a new issue of common shares to make the shares more attractive to investors. Attaching warrants to a share issue is a relatively common practice, and recent years have seen an imaginative variety of different kinds of warrants, some of which can be subject to somewhat different tax treatment . A less common financing strategy which certainly deserves some consideration involves the possibility of utilizing ""Share Purchase Tax Credits "" in conjunction with a new share issue.IntroductionPrevious subjects covered in Tax Notes have dealt with flow-through shares and other tax angles which can make equity issues more appealing to potential investor s. Two other techniques which can add zest to a new stock issue involve the utilization of warrants and ""share purchase tax credits"" (or SPTCs). This article takes a brief look at the better known subject of warrants and the lesser known matter of SPTCs.Of course, this paper presents only a relatively general summary of the income tax implications of warrants and SPTCs, and is not intended to be a definitive commentary on all of the detailed and complex tax issues that might be relevant in the circumstances."

Jan 1, 1985

By C. Bourgoin

"The factors constraining productivity in the mining of narrow vein ore deposits are numerous and often interdependent. This paper concerns mining techniques capable of reducing some of these constraints in the case of vein deposits whose dip is less than 45 degrees. Modifications of conventional mining methods as well as suggested new developments are presented, as are matters pertaining to the mechanization of operations as a mean of increasing both productivity and work safety. IntroductionThe mining of vein deposits, whose width (thickness) is generally less than 2 metres and whose dip is often variable, calls for the use of varying stoping procedures as well as appropriate infrastructure and equipment. In the case of intermediate dips (15 degrees to 45 degrees), it is generally conceded that the degree of mechanization is limited and that ore removal via gravity is impossible. This paper proposes certain innovations in matters of equipment use and stoping methods, together with certain technical data pertaining to the application of these new procedures Stoping MethodsTo mine vein deposits, one must choose a method that can adapt to irregular ore limits and allow, as well, for good ore recovery with as little dilution as possible. In addition, it is important to minimize development work in waste rock. In principle, one selects a method that is both safe and profitable; this method will be defined mainly by the nature of the vein deposit and its dip, by the competency of the rock formations and by certain technical considerations. Moreover, the stoping procedure in a given deposit may well change with time as a function of new layouts or new equipment."

Jan 1, 1994

By A. G. Pathan

Rock and soil mechanics investigations were carried out in block VIII at Thar Coalfield, Pakistan. Most of the strata were mainly composed of sand, with an average content of 67.68 %. Laboratory studies of rock and soil samples from drill hole GT-01 revealed that the strata in block VIII are very weak with an average uniaxial compressive strength of 3.59 MPa, an average tensile strength of 0.68 MPa, an average Young?s Modulus value of 0.234 GPa, an average cohesion of 129.19 KPa, and an average friction angle of 55.47°. Slope stability analysis, based on a probabilistic approach, was carried out using Slide-V software. Monte Carlo simulations have been applied to investigate the probability of failure in the slopes of an open pit lignite mine in block-VIII. From the slope stability investigation, it was found that the probability of failure is 0 % at a slope angle of 16°.

Aug 1, 2013

By I. Clauzier

"A new method of managing electricity to reduce costs andimprove profits is discussed. Before taking steps to better manage electricity, it is essential to understand the terms peak demand and energy and their effect on an electrical bill. Knowing how electricity is presently used in the plant is the important first step. This goes beyond knowing how much electricity is used at each time of day, the individual contribution of every plant process to the total plant load must be known. At this point, each process is ranked according to importance to production in order to identify possible savings opportunities. These improvements can then be implemented by simply improving operations or in some cases, through the use of an automatic control system. IntroductionIn today&apos;s competitive environment, controlling costs is becoming increasingly important. All costs associated with operation must be controlled in an effort to improve competitive position. Electricity is a cost component that can and should be managed.Although the term management can mean different things to different people, the intent is always the same: to make the best possible use of existing resources, whether labour, equipment or electricity.The simple approach to managing electricity presented in this paper consists of four steps.I. Understand Peak Demand and Energy. It is essential to understand the terms, peak demand and energy and their effect on your electrical bill.2. Know Your Present Electrical Use. The present use of electricity in the plant must be known. This goes beyond simply knowing how much is used at each time of day, to accurately knowing how each process is contributing to the total plant electrical load, and ultimately to the electrical bill.3. Identification of Savings Opportunities. With this information, energy savings opportunities for reducing the electrical bill and improving profits can be identified.4. Implementing Improvements. Having identified areas of potential savings, improvements can then be implemented in order of their significance. This could be a matter of simply improving operations, or in some eases may mean the use of an automatic control system.These four steps can result in significant dollar savings."

Jan 1, 1987