Search Documents

By D. Milne, G. Snell

"A new method to predict stope hangingwall failure in underground excavations is proposed. This method compares movement rate for stope hangingwalls, determined from changes in strain or deformation, with changing opening geometry. This geometry is represented by the effective radius factor (ERF), a measure of relative distance to supporting abutments from an opening surface point. This strain-ERF (SERF) approach is applied to an instrumentation program for Brunswick mine near Bathurst, New Brunswick. The SERF method for this case study predicted failure at an ERF of 13.9 m and hangingwall failure actually occurred at an approximate ERF of 12.4 m.RÉSUMÉ Cet article propose une nouvelle méthode permettant de prévoir la rupture de l’éponte supérieure des chambres d’abattage dans les excavations souterraines. Cette méthode compare la vitesse de mouvement des épontes supérieures des chambres d’abattage, déterminée à partir des changements aux niveaux des contraintes ou de la déformation, à la géométrie variable de l’ouverture au jour. Cette géométrie est représentée par le facteur du rayon effectif (ERF, de l’anglais Effective Radius Factor), une mesure de la distance relative jusqu’aux appuis latéraux de soutènement à partir d’un point de la surface d’ouverture au jour. Cette approche contraintes-ERF (SERF, de l’anglais strain-ERF) est appliquée à un programme d’instrumentation pour la mine Brunswick située près de Bathurst, dans le Nouveau-Brunswick. Pour cette étude de cas, la méthode SERF prévoyait une rupture à un ERF de 13,9 mètres (m); la rupture de l’éponte supérieure s’est effectivement produite à un ERF d’environ 12,4 m.INTRODUCTIONUnderground stope design can be improved with the installation of field instrumentation. The most commonly used instrumentation for monitoring rock mass behaviour around open stopes is extensometers. The y-axis of Figure 1 represents how the changing rate of movement, measured using either displacement- or stress-type instruments, can be observed over time. The magnitude of movement measured by extensometers can give an approximation of the load on installed support (Milne, Pakalnis, & Lunder, 1996) and a changing rate of movement can indicate approaching instability."

Jan 1, 2018

The Carboniferous sedimentary rocks of southwestern Newfoundland merit investigation because of petroleum, salt and gypsum possibilities and indications of base metallization along the equivalent of the Horton-Windsor con-tact. In this paper, Lower Mississippian (Anguille) strata are divided into three formations: (1) the Cape John below, (2) the Snakes Bight and (3) the Seacliffs. A correlation between these formations and the Craignish, Strathlorne and Ainslie formations of the Horton group? in western Cape Breton Island is suggested. The criteria for the Anguille subdivision are essentially lithological, but preliminary study of included spore assemblages suggests more precise interformational correlations between Anguille and Horton sequences. The re-measured lower portion of the type section of the Codroy group is presented to define more clearly the stratigraphic position of numerous gypsum and limestone beds. Because of rapid facies changes within the Codroy group a simplified two-fold division into upper and lower units is proposed on the grounds of

Jan 1, 1964

By Rob Boom, Yasuyuki Tozaki, Greg Traquair

The objectives of the business case are to examine a proposed metallurgical project and answer fundamental questions about project feasibility, risks, opportunities, and value. A business case fulfills these basic functions: estimates economic value; helps to understand competitiveness; serves as a risk management tool; and serves as a communication tool. A business case evolves with the project life cycle, and supports the gate reviews at the end of each phase of engineering, through to project construction and operations. A business case must be holistic, including all elements of scope that can impinge on project risk and value.

Jan 1, 2015

By A G. Rogers

This paper discusses the lubrication of surface and underground mining machinery and equipment from the standpoint of machine components. The machine components considered are bearings, cylinders, gears, chains, couplings, fluid drives, hydraulic systems, screws and wire ropes. The best selection of lubricants for these machine components, and for sub-divisions of the components, are outlined. They form general recommendations, for average operating conditions in both surface and under-ground mining operations. The American Petroleum Institute's service classification of both engine crankcase oils and gear oils is de-scribed and used in recommending products for these applications. The practical aspect of lubrication is kept foremost in the recommendations, which are designed to meet the requirements of a wide variety of equipment with the minimum number of lubricants. THE lubrication of mining machinery and equipment presents a variety of problems peculiar to the industry. The type of mine, the ambient temperature, water, dust, and operating and maintenance practices, as well as the age and condition of the equipment, are variables which have to be considered in making lubricant recommendations.

Jan 1, 1963

By Roorda H. J, R. R. Saddington, Curlook W

THE copper-nickel sulfide ore deposits of the International Nickel Company of Canada, Limited contain the minerals pyrrhotite, pentlandite, and chalcopyrite. In the extraction of the nickel, copper, and iron, much of the processing involves oxidation of the metals as well as sulfur. Roasting plays a predominant role at several stages in the operations which prepare the constituent metals for refining. Copper, nickel and iron concentrates of various grades, ranging from low-grade nickeliferous pyrrhotite to high-grade nickel sulfide, must be partially or completely oxidized. Figure 1 shows the main points at which roasting is conducted at INCO. Roasting experience at INCO dates back to the time when lump ore was partially roasted in heaps. It has progressed through single hearth roasters, sinter machines, multiple-hearth roasters, flash roasters, and more recently has centered on the development and utilization of fluid bed roasters. The primitive, slow, and inefficient method of heap

Jan 1, 1961

By Mary A. Wells, Amir Hadadzadeh, Mark A. Whitney, Stephen F. Corbin

In an effort to produce less expensive titanium sheet via roll compaction, the room temperature compaction behavior of titanium sponge granules (99.9% pure, Alfa Aesar) was studied under uniaxial die compaction. The titanium sponge granules were irregularly shaped, with a high degree of porosity, having a maximum particle size of 3mm. Manual die compaction was conducted using a Carver hand press, in a hardened tool steel die with 12.61 mm inner diameter. Uniaxial die compaction in a hardened tool steel die with 9.50 mm inner diameter was also performed using a Gleeble® 3500 thermal-mechanical simulation testing system which allowed for controlled deformation rates. Compaction behavior of the titanium sponge was studied using well-established compaction equations (Heckel, Panelli-Filho and Ge), and it was observed that compaction rate influences the room temperature compaction behavior of this material. The Heckel analysis of the titanium sponge showed that the behavior of the material could be analyzed in two compaction pressure regimes. In the low pressure regime (<100 MPa) the granules exhibited high compressibility, while; in the high pressure regime (>100 MPa) lower compressibility of the titanium sponge was observed.

Jan 1, 2015

By Richard S. Allen

"The casual visitor is not apt to think of the Adirondacks as a one-time hive of mining and manufacturing activity. However, where there are mountains there are usually minerals and northern New York State is no exception.The Adirondacks are a rocky shield, a great stone cap pulled down over what is now northern New York. The bedrock consists of layered metamorphic rocks which were once sandstones or limestones on the bottom of a shallow sea that covered the region 1000 million years ago. The highlands are composed for the most part of the igneous rock anorthosite. Ancient earth upheavals at temperatures of at least 750°C mixed molten masses of anorthosite and the minerals it contained with the older metamorphic rock, resulting in deposits of iron-titanium oxide s, red garnet and other valuable minerals. Of these, the most readily recognizable was iron.The first hint of the existence of iron ore in the Adirondack Lake Champlain region of upper New York State seems to have come from a Swedish naturalist, Peter Kalm (1716-1769), who travelled through French Canada and visited the military outpost of Fort St. Frederic in 1749. In July of that year, Kalm wrote:""Among the kinds of sand which are found on the shores of Lake Champlain; one is black and the other garnet-colored... and they sparkle when the sun shines. All the grains of this sand without exception are attracted to the magnet, the uppermost or black sand being about a quarter inch deep...""Concerned primarily with the fur trade, the officers and men who occupied this remote bastion of La Belle France were apparently unaware of the industrial and commercial possibilities beneath their feet. No deposit of iron was then known to exist any closer than the Three River s area in Lower Canada."

Jan 1, 1983

By A. A. McDonald

Anode casting has been in operation for two years in Hudson Bay Mining and Smelting&apos;s Flin Flon smelter. The new plant allows all casting to be done on one shift and so achieves considerable labour savings. The equipment and operations are described. Some important features are as follows: very consistent anode weights by the use of the load-cell controlled casting ladle; excellent mould life ; very low reject rate; and trouble-free take -off tower. Some of the start-up problems are described and an outline is given of the main operator functions. Data on labour, propane and maintenance costs are presented.

Jan 1, 1977

"Shales play a major role in the stability of slopes, both natural and engineered. This paper attempts to provide a review of the state-of-the-art in shale slope stability. The complexities of shale terminology and classification are first reviewed followed by a brief discussion of the important physical and mechanical properties of relevance to shale slope stability. The varied mechanisms of shale slope stability are outlined and their importance highlighted by reference to international shale slope failures. Stability analysis and modelling of anisotropic rock slope masses are briefly discussed and the potential role of brittle rock fracture and damage highlighted. A short review of shale slopes in open pits is presented.INTRODUCTIONShales have been stated to form approximately 58% of sedimentary rock so it is not surprising that they are frequently encountered in both natural and engineered slopes. They represent challenging environments for slope stability due to the wide variation in their engineering properties, their changing behaviour with time due to geomorphic processes and the variation in the failure mechanisms as a function of both stratigraphy and tectonics. An extensive body of literature exists on the terminology and classification relevant to shales; it is not possible in the scope and length of the current paper to review these works in detail and the reader is referred to Farrokhrouz and Asef (2013), Bell (2000) and Goodman (1993) for detailed discussions. It is arguably the case that no universally accepted classification of shales exists today and depending on the field of application the terminology varies widely. Shales in slope stability, for the purpose of this keynote paper, are taken to include material varying in properties from weak rocks to soils and therein lies one of the most challenging aspects in shale slope characterisation for engineering purposes. They have been classified as “rock-like” or “soil-like’, (Underwood 1967) or compacted and cemented, Table 1, Yagiz (2001). Classifications have considered numerous factors including composition, cementation and a wide range of engineering properties.The propensity of shales to degrade with time due to geomorphic processes has resulted in an important aspect in their classification, that is, the attempts to incorporate slaking, durability and swelling and softening behavior through purpose developed testing methods (Gamble 1971, Morgenstern and Eigenbrod, 1974). Figures 1 and 2 show examples of terminology used to describe argillaceous materials and some proposed engineering classification schemes (Grainger 1984 and Bott 1986). Corominas (2014) provides a recent classification of argillaceous rocks and their durability relating five stages of slope deterioration to the texture of the rock on Ternary diagrams. No attempt will be made here to discuss the merits of the proposed terminology and classifications, suffice it to say, that the controversy and flux surrounding these issues is a strong indicator of the complexities in the behavior of these materials. In this paper the author will consider slope stability in the materials indicated in Table 1, Figures 1 and 2 without undue focus on terminology. At the lower strength limit of shales the engineer must design slopes using the principles of soil mechanics which may vary from the simple Mohr Coulomb plasticity constitutive criterion to modified critical state models, some even attempting to incorporate softening behaviour in the weaker clay shale materials. Given the transitional nature of shale materials several workers have treated overconsolidated clays and clay shales using concepts such as peak and residual shear strength, brittleness index and softening. Martin and Stacey (2013) provide a useful review of the importance of weak rocks in open pit mining, with mudrocks as a specific member, and note the importance of delayed failure, progressive failure and loosening in the stability of"

Jan 1, 2015

By B. B. Adhikari, S. Alam, Ohto Kawakita, Abe Pangeni

Effective recovery of gold was investigated by using adsorption gels prepared from pure cellulose, cotton and paper by treating with concentrated sulfuric acid. Only gold was adsorbed with extraordinary high loading capacity from varying concentrations of hydrochloric acid separated from other precious metals and base metals. The formation of fine powders of metallic gold was visually observed, which is attributable to the selective reduction of gold (III) ion to metallic gold clue to its high oxidation-reduction potential. Recovery of gold from the leach liquor of hydrochloric acid of circuit boards from spent mobile phones was attempted using pure cellulose gel.

Jan 1, 2011

By L. M. Pidgeon

"Part I. - PrinciplesIntroductionIf the oxides of the metals are listed in decreasing order of the magnitude of their heats of formation, the list appearing in Table 1 will be formed. It will be apparent at once that this is essentially the well-known electrochemical series (Table li). The metals at the bottom of the list exhibit great stability and are attacked only by the most violent of chemical reagents. Higher on the list, the metals become more reactive until, at the head of the list, the metals lithium and calcium are unstable in moist air.The reactive metals to be considered lie above manganese. In this group will be found familiar and abundant metals such as aluminium and magnesium, the unfamiliar yet abundant metal titanium, the rare and mysterious metal beryllium, and others of greater or less interest.While these metals exhibit properties as unlike as those of uranium and magnesium, they have in common a specialized and difficult extractive metallurgy. They form compounds of great stability, and their reduction is to varying degrees difficult. The position of a metal in Table 1 (and more particu1arly its position in the free energy column) gives a numerical value to this property.Oxides with low free energies of formation may be reduced with great ease; thus silver and mercury may be produced from their oxides by simple heating in air.Lead, iron, and zinc may be separated from their oxides by heating with carbon to moderate temperatures. Magnesium oxide, on the other hand, .requires a high temperature and very special conditions before it will yield magnesium metal."

Jan 1, 1950

By D. J. Bowen

"Abstract -The Great Dyke extends for 540 km along strike, to unknown depth, and varies in width from 3 km to 11 km. Rb/Sr age determinations gives values of approximately 2470 Ma.The Dyke consists of a variety of mafic and ultramafic rocks, many altered to serpentinites. These include, from top to bottom, successions of gabbro/norites, pyroxenites, peridotites/harzburgites, and dunites/picrites.The layers dip in from either margin, steepest at the edges (20°) and flattening toward the central sections. Four separate complexes are present. From north to south these are termed the Musengezi, Hartley, Selukwe and Wedza Complexes, and are described as &apos;boat-shaped&apos; or &apos;pig-troughed&apos;. All are similar in petrological sequences. Physiographically, the Dyke is spectacular in the north, where as a mountain range it meets the Zambezi Escarpment. Elsewhere in the central parts there is little surface expression and wide open treeless vleis. Dyke rocks cut through granite and schist belt terrain and are termed &apos;The Magnesia Belt&apos;.Vast mineral resources exist. These include chrome, asbestos, platinoids, nickel, copper and gold. Up to eleven chrome seams numbered from top to bottom occur in the lower ultramafic sequences. Seams are narrow at 10 cm to 30 cm but of high grade. The platinum occurs 10 m to 40 m below the norite/pyroxenite contact.A 60 m wide zone of Light Sulfide Mineralization (LSM) of Jess than 1% sulfides extends from the lower gabbronorites into the upper pyroxenites. In this LSM, four enriched zones carry up to 5% sulfides. The most widespread is termed the Main Sulfide Zone (MSZ), below which is No. 2, No. 3 and No. 4 Sulfide Zones. The MSZ carrying pyrite, pyrrhotite and chalcopyrite is a multi­ element ore with components of PGE (Pt-Pd-Rh), nickel, copper and cobalt, and gold and silver.Extensive exploration programs have been carried out and the intention is to begin large-scale mining. However, with Russia supplying metals to the western markets, South Africa&apos;s cutback on production, and an end to the Cold War, delays have arisen."

Jan 1, 1994

By E. Swartzman

This paper presents a general re-view of the various methods of briquetting coals, with and without the aid of a binder, with special reference to the production of a suitable briquette from Nova Scotia 'fines' for re-blending with industrial coal. From the economic and technical viewpoints, either small stoker-sized briquettes made with about 4 per cent asphalt in standard low-pressure double-roll presses, or briquettes made without binder in high-pressure double-roll presses, appear to be the most reasonable solution at present.

Jan 1, 1959

By Mike Fontaine

The success of a project is defined by meeting the financial performance objectives of the business case within a stipulated timeframe. Early in design, little information is normally available; the uncertainty introduces risk to the project outcome. Using a range of risk management tools and techniques, a project can be developed from front end loading phases 1 through 3 (FEL1–FEL3), and project implementation (FEL4) and then into operations with an optimized probability of success. For every project element, the risk management framework embodies: establishing a context; assessing risk (identify, analyze, and evaluate); and treating risk. Embedded within design activities, this process mitigates or eliminates risks. Monitoring and control, as well as extensive communication and consultation with stakeholders, is integral to the risk management process.

Jan 1, 2015

By P. Tracy

An advanced real-time monitoring system, called a "Tapblock Diagnostic System" is under development to help furnace operators manage the operation and maintenance of their tapblocks. The life of a water-cooled tap block in a smelting furnace ranges from several months to several years, depending on the operating conditions. Tapblocks are typically replaced at regular maintenance intervals; a strategy based largely on historical records and not on the actual condition of a particular tapblock. The Tapblock Diagnostic System monitors the tapblock throughout its life and accumulates probable wear events to help the operator assess the residual integrity of the tapblock. Benefits of this system include the ability to provide early warnings of tap block wear to provide improved safety and maintenance planning. Using cooling-water flow together with copper and water temperature measurements, the system performs calculations that compare the present tapblock performance with the expected operating envelope using a multivariate statistical method (Principle Component Analysis). The operating envelope is pre-calculated for a wide range of operating conditions using transient thermal modeling (Computational Fluid Dynamics). A state indicator in the form of a green, yellow and red light is used to inform operators of the tapblock performance and health status.

Jan 1, 2007

By E. R. Hughes

Introduction Situated 182 miles east of Vancouver, on the Kettle Valley branch of the Canadian Pacific railway, the Princeton coal field is readily accessible to the Coast markets. The area covers approximately forty square miles and present indications are that the deposits should contain at least 300,000,000 tons of coal. Comparatively little development has yet taken place in this coal field. Since the commencement of recorded output, the collieries operating in this area have produced 1,640,518 tons of coal. The coal field proper includes only the Tertiary deposits adjacent to the town of Princeton and does not include the Coalmont or Nicola deposits. Production has never been on a large scale. The largest annual output from any property was 81, 780 long tons mined at the Granby colliery in 1940. Coal output was first recorded in 1909 and since that time fifteen properties are reported to have either mined coal or to have done prospecting or development work; of these, only two are presently active. However, none of the properties now inactive were closed because their coal resources were exhausted. The accompanying key map shows the extent of the Princeton coal field, and the location of the coal mines and prospects in this field General Geology The Princeton field is underlain by rocks of Oligocene age and is one of the series of more or less isolated Tertiary lake basins in which coal, or lignite, has been found in the interior of British Columbia. Resting on the Nicola group rocks of Triassic age, the Princeton sedimentaries consist of sandstones, conglomerates, shales, bentonite, bentonitic clays, and several seams of coal. Tertiary volcanics occur both above and below the stratified rocks and in places they have been thrust through the overlying measures. In some areas, the coal has been burned to a red ash as the result of vulcanism, while in other parts some of the moisture has been driven from the coal, thus improving the grade. The field can best be described by dividing it into two areas: the Southern area, lying to the south of the town of Princeton, where most of the mining has been done; and the Northern area, to the north of Princeton, where very little development has taken place.

Jan 1, 1947

By Guoxiang Chi

The Cornwallis Fold Belt in the Canadian Arctic Archipelago contains numerous Mississippi Valley-type (MVT) Zn- Pb occurrences and the world-class Polaris deposit. The occurrences are mainly hosted by the dolostone in the Thumb Mountain Formation which spreads over 25000 km2. Success in exploration requires further understanding of the genesis of these occurrences and an assessment of their parentage with the giant Polaris deposit. Syn-sulfide dolomites in regional occurrences share C-O-Sr isotopic characteristics similar with Polaris dolomites, indicating warm basinal brines enriched in 87Sr. The dolomites and sphalerites contain fluid inclusions with ice-melting temperature between ?45° and ?25°C, which is significantly lower than for most MVT districts in the world (?30° and ?10°C). These characteristics indicate that all the Cornwallis occurrences were produced by fluids of the same sources and/or aquifers. The deposit size was largely controlled by the rate and duration of the metal-carrying fluid flow, and by the availability of reduced sulfur at the site of mineralization.

May 1, 2001

By P. Clinton Milne

Uranium mines in Washington State include the producing Midnite and Sherwood mines and several mined-out deposits, the most productive of which was the Daybreak mine. The Midnite mine is generally classified as a hydrothermal deposit consisting of tabular orebodies in Precambrian pelitic and calcareous metasedimentary host rocks. The host rocks occur as roof pendants in a Cretaceous porphyritic quartz monzonite intrusive; the quartz monzonite averages 12 ppm U308 The uranium deposit appears to have undergone a complex genesis, involving a series of depositional and enrichment stages. The Sherwood uranium deposit, approximately 4 miles south of the Midnite mine, occurs near the bottom of a basal Late Cretaceous to Paleocene arkosic conglomerate. The conglomerate lies nonconformably on the porphyritic quartz monzonite that is associated with the Midnite deposit. The Sherwood and Midnite uranium deposits may have had a similar genetic history linked by a common uraniferous pluton source, ground-water action, and/or leaching of uranium-rich ash flows from now-eroded, overlying, Eocene volcanics. The Daybreak deposit, in northeastern Spokane County, consists entirely of secondary uranium mineralization (metaautunite) in a quartz monzonite pluton. Mineralization is confined to a low-angle fault zone and is most highly concentrated at the intersection of primary and secondary shears. Both hydrothermal and ground-water origins are feasible. Besides the Midnite-Sherwood area, 14 other areas in the western Okanogan Highlands physiographic province and Cascades region have favourable characteristics for uranium potential. Criteria include the existence of uranium occurrences, Tertiary basin sediments with intercalated volcanic and volcaniclastic rocks, favourable geochemical data, alkaline plutons associated with uranium occurrences or borders of Tertiary basins, and structural controls.

Jan 1, 1979

By T. M. Korzekwa, R. L. Cavanagh

Following considerable experience with the beneficiation of Wabana iron ore by standard methods, a study was made of the benefits to be obtained by semi-reduction. The basis of the laboratory program was an extensive mineralogical and liberation investigation which guided subsequent work. Partial reduction and beneficiation on a laboratory scale was carried out on lump ore and fines. The reduced ore was magnetically concentrated and the concentrated fines were briquetted. Data are presented on reducibility, sizing vs reduction rate, magnetic cobbing and separation, and the elimination of phosphorus. Past work is reviewed briefly and comments are made on the relation of laboratory to pilot-scale tests.

Jan 1, 1967

By Marvin E. Lane

Viburnum, located in the foothills of the Ozarks in south-east Missouri, is the site of a modern lead mining and milling operation. Two mines are currently producing a total of 5,000 tons per day and a third mine is in the final development stage, with full production scheduled for late this year (1964). These mines will supply the tonnage required to keep the Viburnum mill operating at a full capacity of 7,000 tons per day for many years. The efficient underground mining operation is completely trackless. Drill jumbos are used to break the ore in a room and pillar method of mining. Transloaders, or St. Joe shovels, and trucks do the loading and hauling. The Viburnum mill has a world-wide reputation as a most efficient operation. This is due to the extensive use of automatic process controls, and labour saving materials handling facilities. Introduction THE St. Joseph Lead Co., has operated lead mines in southeast Missouri for 100 years. These operations have been confined largely to the area called the

Jan 1, 1964