Search Documents

By T. K. Bose

According to the Intergovernmental Panel on Climate Change (IPCC), the average global temperature has risen over the last century. If this trend continues over the next century, the IPCC projects a significant increase in temperature and a rise in sea level. The changes in climate could adversely impact human health, agriculture, water resources and ecosystems. Most national and international agencies have concluded that our use of carbon-rich fuel is responsible for global warming through the greenhouse effect. In the future, the situation may get worse if the increased need for energy in countries like China, India and Brazil is fulfilled by burning fossil fuel. Advanced natural gas-fuelled vehicles have the potential to reduce carbon monoxide and reactive hydrocarbon emissions substantially compared to gasoline vehicles. Further environmental benefits can be realized by using a blend of natural gas and hydrogen. Such an approach will help create an infrastructure for an eventual transition to hydrogen.

Jan 1, 2005

By K. V. Konigsmann

"The results of Mr. Klymowsky's research confirm the essential role played by oxidation products in the flotation of base metal sulphides. They invite a discussion on the subject of aeration which I may open by a brief description of the development and current practice of aeration. The first installation of pre-flotation aeration in Canadian milling practice was undertaken during the years 1928 and 29 at the then new Noranda Mill. C.G. McLachlan and his collaborators demonstrated that the flotation differential between chalcopyrite and iron sulphides was enhanced by aeration in soda ash alkaline pulps. The ores treated contained more than 80 per cent sulphides. It was proposed already then that the products of mineral oxidation assisted copper and retarded iron sulphides, at least pyrrhotite flotation. The concentration of thiosulphates was used as a measure of the progress of oxidation. Several papers by C.G. McLachlan elaborate on this subject.The aerator was also used as classifier since it was held that aeration, i.e. controlled oxidation, should go hand in hand with creation of new mineral surfaces. Grinding mills and aerators were placed in closed circuit. Figure 1. This aeration was essential for successful separation at Noranda.Following the application of aeration at Noranda the technique was applied to existing mills in N.W. Quebec. Impressive improvements in concentrate grades and recoveries were obtained. It was observedthat the zinc flotation benefitted from aeration as much as the preceding copper float. In the late forties and fifties the aerator classifier was installed in new mills associated with the Noranda group. A diagrammatic sketch of the Quemont flow-sheet (figure 2) may serve as a typical example."

Jan 1, 1973

By A. A. Beland, R. J. Dawson, S. Shewchuk

"Shovel buckets, scraper blades, dipper teeth, mine car wheels and hammermills are examples of equipment which require routine maintenance due to abrasion. Service life can be extended by the use 0/hard/acing and buildup materials. Mining and milling applications are described and field welding procedures discussed.A high-stress abrasion test used to select hard/acing and buildup materials/or hammers in a hammermill is described in detail. Field tests of the selected alloys confirmed their performance, and maintenance records showed a significant saving in down time and cost.The relationship between the abrasion resistance of the alloys and their hardness, work hardening, composition and microstructure is summarized. IntroductionLarge volumes of ore are handled daily by the mining industry. The abrasive nature of most ores results in extensive wear to both handling and processing equipment. If such wear is neglected it may cause lost production time and also, in extreme cases, require the complete replacement of expensive equipment. The well-planned maintenance of components subject to abrasive wear by means of buildup materials and hard facing can result in substantial economic benefits. Such benefits can , however, only be realized through the correct choice of welding process, consumables and deposition methods available to maintenance personnel. Hardfacing MethodsHardfacing is applied by a variety of methods; the three most widely used being arc welding, oxyfuel gas and thermal spraying. Table 1 summarizes the major processes used within each method. Filler metals in the form of rod, wire or powder are necessary to fulfill the individual requirements of each process. The filler rods are available in the cast form or, in the case of ductile metals or alloys, as wrought rod or tube. All types are supplied bare or flux covered. Wire is supplied in two forms, drawn flux cored and drawn solid. Powder filler metals are available in many metals or alloys; they may be simple mechanical mixtures or prefused and atomized alloys made to a specific size range and shape for optimum results for each applicable process."

Jan 1, 1980

By K. D. Hester

This paper will review the metallurgical aspects of the completed expansion program at Quirke, and the current rehabilitation and refurbishing program at Panel. During the Quirke program, completed at the end of 1977, the plant capacity was increased from a nominal 4,500 to 7,000 short tons per milling day. The expansion of crushing, grinding, neutral thickening and filtering, leaching, partial neutralization, sand-slime separation, sand washing, C.C.D., clarification, ion exchange, mine water treatment, and tailings neutralization and pumping will be considered. The application of Enviro-Clear thickeners in the mine water treatment circuit and in the C.C.D. will be briefly reviewed. An automatic grinding and classification circuit for limestone will also be covered. The refurbishing program underway at Panel will be discussed. The Quirke and Panel plants will be contrasted and compared. In particular, reference will be made to environmental considerations. The innovative system for producing yellow cake at Panel, LAMIX, will be considered as well as the proposed treatment system for Panel tailings.

Jan 1, 1979

By Karim El-Ouassiti, Marc Minville, Stéphane Chabot, Claude Bazin, Valérie Ouellet

"Alumina is the main source of aluminium and it is extracted almost exclusively from bauxite ores found in the Southern hemisphere. Clays are abundant minerals that contain from 15 to 40% w/w of alumina from which it can be extracted by various processes. This paper reviews the processes used for the extraction of alumina from clays and discusses results obtained with a clay sample from the Murdochville area in the Quebec Province. The application of a conventional process to this clay did not yield an acceptable recovery although smelter grade alumina was produced. A modification to the process allows increasing alumina recovery from 85% to more than 92%. The application of the improved flow sheet to other alumina carriers failed to yield comparable recovery, showing that an optimum processing path for the recovery of alumina should be found for individual clay materials.INTRODUCTIONMost of the aluminium smelters are fed with alumina extracted from bauxite found in the Southern hemisphere. Bauxite is processed by the Bayer process that uses a caustic leach of the ore. In the middle of the century, the US Bureau of mines, motivated by the fear of an alumina delivery disruption, conducted several research projects aiming at producing alumina from non bauxitic ores. These projects led to the development of various acid leaching processes (Habashi, 1993). The sulphuric and hydrochloric acid leaching processes were brought to pilot plant evaluation (Bengtson, 1979), while nitric and other leach liquors were tested in the laboratory (Phillips and Wills, 1982; Habashi, 1983). Although clays are abundant and inexpensive minerals, the studied processes remained uncompetitive with the alumina extraction from bauxite (Hudson, 1987 page 42; Peters et al., 1962) for which reserves are estimated to support alumina production for the next 50 years (Oye et al., 1999). On the other hand, the local extraction of alumina from clays could significantly reduce the transportation costs of alumina to smelters and provide an alternative source of alumina supply from the Southern hemisphere countries. Also, the extraction of secondary products for some types of clay (Nasyrov et al., 1999) containing significant amounts of potassium and sodium could provide an additional return that may improve the economics of alumina production from clays."

Jan 1, 2005

By A. Wright, P. Lacombe, R. del Villar, D. Hodouin, C. Sepulveda

"The data acquisition from industrial plants is a fundamental step for process modelling in process optimization, process analysis and automatic control.The introduction, some years ago, of modern distributed control and data acquisition systems in concentrators imposes a new approach in designing experimental schemes for data acquisition campaigns and new criteria for the treatment of the obtained discrete information.This paper presents the methodology applied to sample a zinc flotation circuit at Les Mines Selbaie, Joutel, PQ. Values of 85 process variables were obtained form the Distributed Control and Data Acquisition System (Bailey Network 90) and transferred to the DOS environment. Another 11 variables (flowrates and valve positions) were directly sampled using an IBM-PC compatible computer equipped with a data acquisition card and a signal processing circuit.All variables, under the vector form, were processed in the PC-MATLAB environment to either filter or eliminate the non-linear disturbances and noises, producing useful data for model development. The filtering algorithms are also presented.INTRODUCTIONProcess control does not need to be justified. Whether manual or automatic, any processing plant requires some form of control to accomplish its main objectives: a good quality product and a target throughput. Process control of mineral processing plants has steadily evolved from manual control, where the operator skills and/or experience play an important role, to some level of automatic control, usually considered better, as less human subjectivity is involved, at least when actions have to be taken.The design of these control systems requires the knowledge of the dynamics of the process it is deemed to control. Process modelling is therefore an essential step in the assessment and the design of a control strategy. The choice of model will depend on the available resources and manpower."

Jan 1, 1991

By Henri F. Letient

At the 25th Annual B.C. Mine Reclamation Symposium in September 2001, Huckleberry Mines Limited received the Jake MacDonald Reclamation Award for its exemplary mine waste management plan, conceived to prevent the onset of acid mine drainage and facilitate reclamation of the site. The mine is an excellent example of a total mine waste management plan, with all materials scheduled in detail for the life of the mine. The filling plan for the waste management facility takes into consideration the requirement for permanently flooding the potentially acid generating rock. From an acid generation point of view, the tailings fall in the zone of potentially acid generating material. To avoid long-term ARD concerns, it is planned to float pyrite out of the tailings towards the end of the mine life, thereby generating a non-acid generating tailings stream which will be used to cap the deposited mine waste. The pyrite-rich tailings will be discharged into the deeper portion of the impoundment. On closure, a permanent water cover will be maintained over the mine waste. Only beaches of non-acid generating tailings will remain exposed. Mining will be phased to also allow one of the pits to provide storage for potentially acid generating rock and to be flooded at the end of mine life.

May 1, 2002

By Olli Aulio, Outokumpu Oy

"GENERALThe Outokumpu Company is today an important European producer of metals from its own mines: copper nickel cobalt, ferro chrome and zinc being the main products. In 1972 about 4 million tons of ore was hoisted from eleven mines.Outokumpu Oy has gained experiences on the various aspects of on line computer control since 1968. This knowledge has been combined to develop a standard computer control package for concentrator control. Before the development of computer control package was started Outokumpu Oy had three large computer control systems. The first system was at the Pyhasalmi Concentrator, thee second at the LokkolaPlant, and the installation of the third system at the Vuonos Concentrator was just started.The characteristics of general computer software packages - both control and executive ones - were thus well-known as well as the practical usage of control theory. Furthermore Outokumpu had developed the Courier analyzer which included a so-called minicomputer. This project had given experience both 1n totally self made real tire executives and in computer hardware and peripheral d=vices. The instrumentation of the Outokumpu concentrators was designed and installed traditionally by the engineers of Outokumpu themselves."

Jan 1, 1973

By Marc C. Bétournay

Under the requirement to define the economic advantages of using hydrogen fuelcell vehicles, a broadscoped project was initiated to quantify the costs associated with operating fuelcell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another. This article outlines the results of the investigations to date defining the costs/benefits associated with: capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America. Significant ventilation power, equipment and infrastructure savings are possible with the application of fuelcells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuelcell mining equipment is currently higher than diesel versions, the high cost of fuelcells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case the operational savings would probably be sufficient to balance the supplementary capitalization costs. A comprehensive cost-benefit report will be issued in the near future.

May 1, 2003

By A. J. Magerowski

Energy consumption is a main component of operational costs for the comminution of mineral bearing ores. Reduction of energy consumption has continually been addressed by mill operators and equipment manufacturers. Our testing over the last few years strongly indicates that the overall energy needed to comminute a mineral bearing ore can be brought down significantly, if more work is done in the crushing stages of the comminution circuit.This calls for uprating of the conventional crushing equipment into a new generation of crushing equipment to produce finer products. This will result in the emergence of new ideas in the design and application of equipment and corrnninution circuits.

Jan 1, 1986

By Jamie Archibald

The Department of Mining Engineering at Queen?s University conducted a study of backfill practices in underground mines across Canada to assess the current state of backfill usage and to overview potential hazards associated with backfill practice, from preparation to transportation to placement. The primary aim of this study was to cover each component of a typical mine backfill system, and to identify potential incidents leading to the disruption of backfilling operations and any associated corrective actions. This paper, Part II of the study, deals with underground operations consisting of backfill transportation and backfill placement. Part I of the study, which deals with surface operations consisting of backfill material supply and backfill plant preparation, is also presented in these proceedings. A review of safety measures associated with current backfill operations and recommendations for procedures of best practice that should be implemented to reduce fill-related hazards in all mine backfill workplace environments are presented. In general it has been found that system failures normally lead only to minor losses to the operations.

May 1, 2009

By Denis Thibodeau

his paper describes a study of an altered mining extraction and the resulting Rockmass response at VALE?s Creighton Mine. Typically, the deep mining zones have strict stope extraction guidelines to ensure safety and productivity; however, these guidelines offer low flexibility or few options for stope sequencing. The 402 O. B. being in a good rock mass, at moderate depth and stress regime at Creighton, offered an opportunity to drive a more flexible mining sequence with stopes and a pillar. A three-phased approach was used to mitigate risk of the mining plan: 1- Numerical modelling to fully anticipate rock mass response to the proposed mining sequences. 2- In situ seismic monitoring to collect stress and seismic activity data. 3- Analysis of the in situ data to correlate to the modelling results. The creation and the extraction of a pillar in the 402 O. B. was successfully completed. The recorded seismic activity agrees well with the numerical modelling since most of the seismic activity is localised in the hangingwall where the deviatoric stress corresponds to an early damage process. The moderate levels of deviatoric stress cause localised failure with low level of seismic activity.

May 1, 2013

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

By Khosrow Ebrahimi

We document the occurrence, mineralogy and firing properties of magnesite from hydrothermal deposits in the upper Cretaceous ophiolites of Eastern Iran. These deposits occur as thin veins of nearly pure cryptocrystalline magnesite with only trace amounts of quartz, calcite, and dolomite. Ratios of CaO/SiO2 in the bulk ore are variable. The composition of dead-burned magnesite from these deposits, calcined at different temperatures and durations, is predictable from phase equilibria. Textures of the calcined magnesite were studied by SEM; results show that the principal impurites produced during calcination are forsterite, monticellite, merwinite, dicalcium and tricalcium silicates, and that these are located principally at triple junctions of the periclase crystals. The size of periclase crystals increased with temperature and duration of calcination and the amount of periclase-periclase grain contacts was reduced by increasing the concentration of impurities in the starting products. EPMA show: 1) that CaO and FeO contents in periclase increase steadily with an increase in the CaO/SiO2 ratio and the FeO content of the bulk ore, respectively, and 2) that limited solid solution exists between impurites. This study demonstrates that high quality dead-burned magnesia refractories can be produced from the Iranian magnesite with low CaO, SiO2 and FeO contents.

May 1, 2004

Ontario Operaations Mining Garson Stobie Copper Cliff North Copper Cliff South Creighton Mcreedy East Milling Clarabelle Mill Smelting Smelter Matte Processing Anode Casting Refining Copper Cliff Nickel Refinery Port Colborne Cobalt Refinery

May 1, 2007

By S. Cossio, J. L. Noyola, R. Espinosa

"Minera Penmont’s La Herradura is a joint venture between Industrias Peñoles, S.A. de C.V. and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with a two-stage crushing plant and heap leaching facility. Gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130 000 oz gold per year and its treatment capacity is approximately 22 000 t/d. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to coarse visible gold, which in some cases ranges from 100 to 600 microns.Sampling and assaying protocols were established during exploration and prior to start-up of operations, based on nomographs developed from early heterogeneity tests. However, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block consisting of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to start-up of operations (existing) and the new protocol (leaching). In the existing protocol, sub-sampling is done through riffle splitters, and coning and quartering. Fire assaying was used to estimate the gold content on a 50 g sample. In the leaching protocol, a 12 000 g sample of bottle-rolled cyanide was leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this rotary sampling protocol and for comparison purposes, gold assays were also repeated using the leaching protocol.Test results were compared in three groups: < 0.3 g/t (below cut-off), 0.3 to 0.8 g/t, and >0.8 g/t. Overall, results show that the protocol established prior to start-up of operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2004

By Lloyd Rowson

??Several factors have led to a review and reoptimization of the Midwest uranium deposit by AREVA Resources Canada Inc., the project operator, on behalf of the owners ??The current proposal is to mine the deposit using open pit methods and then transport the ore by truck on a dedicated road linking the Midwest site with AREVA?s McClean Lake Operation (JEB mill) for processing ??A decision has been made to begin mining the deposit by 2010 (pending regulatory approvals)

May 1, 2008

By Lam. E. K., J. W. Jarvi, B. P. Bharadwaj

"The Rabbit Lake Operation is located in Northern Saskatchewan on the western shore of Wollaston Lake approximately 800 km north of Saskatoon, Saskatchewan.The Operation is owned by a joint venture of Cameco Corporation and Uranerz Exploration and Mining Limited. Cameco is the operator.The Mill started production in June 1975 under the ownership of Gulf Minerals Canada Limited and over the past twenty years has increased the rated production capacity to over twice the original design.The Mill was originally designed to process 485,000 tonnes per year of ore with an annual production of 2.0 million kg of U308 (yellowcake). During the past ten years changes in ore sources and process modifications have led to increased milling capacity and production targets. The Mill has treated a total of 8.6 million tonnes of ore and produced over 40 million kg of U308 in the twenty year period, despite the shutdown and cutbacks in operating time since 1989.The 1995 tonnage throughput was 206,000 tonnes per year. Annual production though has risen to 3.6 million kg of yellowcake despite the departure from full-time to half-time operation in 1991 (7 up-7 down). The forecast for the coming years will see tonnage rising from 300,000 to 570,000 tonnes, production of 4.5 to 5.4 million kg of yellowcake and an anticipated return in the year 1998 to full time operation.This paper will give a brief history of the Mill and focus on the present flowsheet and recent improvements to the process."

Jan 1, 1996

By F. Daniel Rosenkranz, Peter L. Silveston

Experiments investigating the treatment of a ground wood white water waste from an Ontario pulp and paper mill by an HVCB coal are reported. Adsorption capacity for the waste, with a soluble COD contribution of 2,100 mg/I, amounted to 0.17 per cent, by weight, of the Nova Scotia coal used. Percolation of the white water waste through a coal bed indicated that soluble COD is removed. For finely ground coals, over 90 per cent of the suspended solids in the waste are retained on the coal. Plugging of the coal bed is rapid, so that any treating process using filtration would have to renew the surface of the bed frequently.

Jan 1, 1970

By L. R. Plitt, A. J. Neale, B. C. Flintoff

"INTRODUCTIONThis is not a technical paper in the normal sense. It is an informal document which is intended to share the results of some recent cyclone research with our colleagues both in operations and in research.PILOT PLANT FACILITIESFigure 1 is a schematic of the closed circuit hydrocyclone pilot plant testing facility at the University of Alberta. In this figure the system is configured for some experimental work on wide angle cyclones which was recently completed. The rig is designed to study cyclones in the approximate range of 10 cm to 20 cm diameter. Notable features include the variable speed feed pump, the magnetic flowmeter and pressure sensors on the cyclone feed line and the travelling launder which permits simultaneous sampling of both product streams.ORGANIZATIONFor organizational convenience the subject matter has been divided into three parts:(1) Peculiar Partition Curves(2) Wide Angle Cyclones(3) Rope DischargePECULIAR PARTITION CURVESMuch of the initial empirical mathematical modelling work on cyclone classifiers dealt with homogeneous ores. A homogeneous ore is one in which all particles have substantially the same apparent density, or where one phase is very clearly predominant. In contrast, a heterogeneous ore is one in which there are at least two different density classes, each making a significant contribution to the ore composition. (Particle shape similarity is always assumed.)One of the problems which can arise when analysing the overall solids partition (selectivity, Tromp, etc ... ) curve for a heterogeneous ore is the peculiar shape which may be observed, when compared to partition curves for homogeneous ores. This is not an unusual occurrence and it has been documented by Lynch and Rao, Finch and Laplante and Larsen and Spring. The purpose of this section is to identify those operating conditions which may give rise to peculiar partition curves."

Jan 1, 1986