Search Documents

Long-range side-scan sonar and conventional geophysical data for the Peru Trench region (8`S-15¦S latitude) have been analysed. The data show that the Peru Trench is a site of sediment subduction where bending-induced normal fault-ing of the Nazca plate plays a key role. The sediments are continually removed from the trench axis region by their inclusion in normal fault-defined void spaces, such as grabens. In the process of subduction, the sediments are often offscraped, folded arid kneaded temporarily at the base of the shoreward trench slope. The subduction complex comprising such sediments is narrower than 20 km and its volume remains more or less constant due to regular removal of its contents along with the down-going plate. Addi-tionally, morphology of the subducting Nazca plate is responsible for subduction erosion of the South American plate, where the horst blocks cause tectonic erosion by abrasion and the grabens provide a mechanism for removal of the eroded material.

Jan 1, 1990

By Hematian J

A high horizontal stress field has significant effect on the stability of underground roadways and influences the design of a support system in this environment. The high horizontal stresses at E1lalong Colliery, NSW, Australia provided the environment for this study. Samples of coal measures 'rock were collected and tested to determine their mechanical properties. The lithology, stress state, geometry and conditions prevailing in particular areas of the mine were obtained from geotechnical reports available at the mine and by field observation. The results of a series of finite element models constructed and tested under various conditions provided a basis for comparison with field observations. Analysis of the results indicated sufficient correspondence to provide a basis for the proposed design of an optimum support system. It is not suggested that finite analysis provides 'exact answers', but it does show the relative importance and interaction of various parameters.

Jan 1, 1995

By P Kumar, J Safarian

Understanding how ore interacts with flux particles at elevated temperatures to create molten slag is crucial since it governs the dynamics of a chemical reaction. This study explores the smelting behaviour of pre-reduced Nchwaning manganese ore when combined with lime, with the objective of examining the evolving interaction between pre-reduced ore particles and lime over time. The research sheds light on the interaction between solid and liquid and the phases that emerge during this process. To achieve this, a sessile drop furnace was employed to rapidly heat the materials positioned adjacent to each other on an alumina substrate and to observe the smelting process as it unfolded over time. This method allowed for the direct observation of the melting temperatures and the flux-ore reaction progression rate, and the potential disruptive events that might occur. By comparing the molten interfaces of the fluxed materials at various time intervals, this study provides insights into the relative rate of slag formation from the two materials. The results indicate that the main slag formation initiated at approximately 1400°C and continued to advance with time, with complete mixing occurring around 1500°C. The possible phases formed were identified using Scanning Electron Microscopy and modelled using Fact Sage thermodynamic software. In addition, the iron particles in the pre-reduced Mn ore were separated and settled from a rich MnO-containing slag. It was found that the separation of molten iron droplets from the slag depends on the rate of solid MnO particles dissolution into the adjacent slag phase.

Jun 19, 2024

This paper details a proposal for integrating the use of the Pilbara Iron Ore Classification (PIOC) and stratigraphic data for fine tuning blast. pattern design on Mt Whaleback. The main thrust of the proposal is based on the assertion from Haqan and Harries (1979) that rock properties influence blasting results more than explosive properties. This premise is supported by a literature search, which indicated that blasthole burden, spacing, stemming and subdepth lengths are also determined by rock properties if the same explosive and blasthole diameters are used. A brief explanation of the PIOC is provided during which it is noted that the classification is based on physical hardness, mineralogical and genetic characteristics of the ore. The classification also extends to the two main waste rock types LBIF (banded iron-formation) and shale]. Ore type plans produced from face mapping indicate that many areas on Mt Whaleback can be divided into various PIOC zones and regions thus making it more useful in blast pattern design. Several recommendations for blast pattern design experimentation are made for hard, medium and soft ores as well as for the waste rocks, the most important being the use of expanded patterns to blast. soft BIF and medium hard to soft shales.

Jan 1, 1986

By T C. Souza Pinto, M Safari, F S. Hoseinian, D Deglon, L Leal Filhoc

In this study, the effect of hydrodynamic parameters on the iron ore reverse was investigated in a mechanical flotation cell. The work carries out using the case study of Iron ore from Vale in Brazil. The influence of hydrodynamic factors such as froth height, impeller speed, superficial gas velocity and solids percentage were evaluated on the quartz flotation. The results showed that the hydrodynamic conditions have a great effect on the flotation performance, especially on the fine and coarse quartz. The size-by-size analysis of the froth products showed that froth height, impeller speed, superficial gas velocity and solids percentage have a significant effect on true flotation quartz particles. The increase in the froth height decreased the recovery of quartz particles. The increase in the impeller speed increases the recovery of quartz particles to an optimum. The increase in the superficial gas velocity improved the flotation of coarse quartz particles. The increase in the solids percentage increases the recovery of quartz particles.

Sep 18, 2023

The Tregoora Gold Project is centred around the old Mitchell River Antimony Field located 100 kilometres west-northwest of Cairns, North Queensland. The project is currently the subject of a joint venture between Strategic Minerals Corporation N.L. and Hawk Investments Limited.Historical BackgroundThe Tregoora area was first prospected for antimony and gold around 1890. During the periods 1905 to 1914 and 1937 and 1944 approximately 100 tonnes of antimony and an unknown quantity of gold were won from a number of small mines the principal one being the "Retina". A strong increase in the demand for antimony in the early 1970's resulted in renewed exploration activity in the region and the re-development of the Retina Mine. Despite the intermittent interest in the region for antimony it was not until 1984 that the potential of the area for hosting gold resources was realised with the delineation by Strategic Minerals Corporation N.L. of a significant gold deposit now referred to as the Black Knight.

Jan 1, 1986

The 250 metric tonnes of gold and 360 000 metric tonnes of copper recovered from the Mt Morgan Mine in Central Queensland justify its fame. The mine ceased operation before the advent of three-dimensional computer graphical modelling of orebodies became common practice in mine planning. The Mount Morgan Mine records however remain and are the database for this study. The Mount Morgan project takes ore deposit modelling one step further by examining the relationship between grade distribution within the orebody and key geological features, as a tool for exploration and development.The Mount Morgan gold and copper mineralisation is shown to be strongly lognormally distributed. The deposit has been split into three areas, using geological boundaries, each with different geostatistical characteristics. Important features include: the spatial relationship of near-vertical, high grade shoots with a ring dyke thought to be related to the North Dyke; separation of the high grade eastern stopes from the others along the Andesite Dyke; and lack of concentrated mineralisation along the Slide Fault.Recognition of these features is useful to those currently exploring the Mount Morgan district for similar style deposits, by stressing the importance, or lack thereof, of the geological features.

Jan 1, 1993

The paper describes a computer model developed within the State Electricity Commis- sion of Victoria for use in open cut planning. The purpose of the model is to simulate all the typical occurrences in, and influences on, the coal supply and overburden disposal systems in order to be able to assess their performance. The model incorporates much of the long term and day-to-day operations planning logic required for the allocation of resources within an open cut. This logic takes account of power station demands, bunker stocks, plant and crew availability, the balance of reserves between dredgers, planned maintenance, etc. The perfor- mance of plant within the system is simulated using random selections from statistical distri- butions of Time to Failure and Time of Failure for each plant item. The application of the model in selecting a suitable bunker capacity in a notional open cut development is described to illustrate the potential of the model in optimising plant selection.

Jan 1, 1982

Longwalling has reached a high standard both in Germany and Australia and most improvements should be expected in planning, monitoring and control. Double drum shearer have electric drives to 1000 kW and automatic height control is under development. Conveyor pans to 40mm thickness and chains to 2300 kN breaking load are in use with controls for pretension and load compensation under test.Trends in support are towards two leg shields with loads to 3850 kN per leg and electrohydraulic controls. Expert systems have been devised for planning and diagnosis tasks. With increases in technical standards, staff qualification standards at rising too, drawing attention to training requirements for modem personnel.

Jan 1, 1991

By Corrans I. J, Yan D. S

The CIP process for gold recovery has enjoyed widespread application in most gold-producing countries. The development of a mathematical model of the CIP process has value for use in process design, process optimisation, and process control. Mathematical model development through laboratory experimentation is an important step in the design and optimisation of the CIP process. For this purpose, data has been generated through small scale laboratory leaching and adsorption tests both in batch and continuous mode. This test program has been carried out on specific ores of various types prior to the application of the models to production CIP plants utilising these ores. The applicability of leaching models derived from batch experiments was tested in a continuous five stage CIP pilot plant. The models were then adapted to scale-up the batch to the small scale continuous operation.

Jan 1, 1991

The Mt Todd Project is located 42 km northwest of Katherine in the Northern Territory. The identified mineral resource estimate for the Batman gold deposit is 66.7 million tonnes (Mt) grading 1.4 grams/tonne (g/t). Proved and Probable Ore Reserves total 42.3 Mt grading 1.5 g/t. Orebody definition and reserve estimation is based on extensive percussion and diamond drilling. Exhaustive bias analysis comparing grades produced from different drilling techniques has been undertaken. Similarly, detailed check assaying programs have been run to validate grade data produced by commercial laboratories used during the exploratory drilling phase. Significant biases were established from both studies and appropriate 'corrections' were made to drillhole databases prior to final resource and reserve estimation. 3D geostatistical modelling has been utilised for resource and reserve estimation, with specialist consultants contracted for this work. At all times, interpreted geological controls on mineralisation, provided by

Jan 1, 1994

By Ranklin W. J, Swinbourne D. R

Lead blast furnace slags contain typically 10 - 20 mass per cent Zn. The zinc can be recovered by slag fuming, in which a powdered coal/air mixture is injected into a molten slag bath. Volatilised zinc is recovered as zinc oxide from the gas and processed hydrometallurgically to produce zinc metal. The ISASMELT continuous lead smelting process in operation at Mt Isa produces a slag containing about 12 per cent Zn which is currently granulated and stockpiled. This slag could flow to a further bath-smelting reactor for continuous zinc fuming. Rather than collecting the zinc as fume from such a process, one option would be to recover it using a lead splash condenser. The success of this operation would depend on the composition of the gas produced, in particular the concentrations of gases capable of reoxidising zinc vapour, viz, carbon dioxide and water vapour. The aim of this investigation was to determine the smelting conditions for a bath-smelting process such as ISASMELT or SIROSMELT which would produce a gas similar in composition to that from an Imperial Smelting Furnace by thermodynamic modelling of the process using the CSIRO Thermochemistry System. It was found that such a gas could be produced if coal injection and oxygen enrichment of the combustion air to at least 40 per cent 02 were used. However, the off-take gases must be conditioned by addition of methane to reduce the water vapour content to acceptable levels. An addition rate of ten per cent of the off-gas flowrate was found to be adequate. Addition of methane to the off-gas had the added advantage of cooling the gas from the bath temperature to a temperature suitable for normal lead splash condenser operation.

Jan 1, 1993

By Richardson F. A

Techniques for flotation optimisation were investigated at Cobar [lines Pty:Ltd., in anticipation of the proposed installation of a computer and on-stream analysis. Successful laboratory and pilot plant tests for flotation performance optimisation using the Simplex Evolutionary Operation Technique (Simplex) lead to a full scale plant test using this method. The index developed for" Simplex response evaluation of flotation performance was based on metallurgical and economic criteria. This index was further modified to minimise the effect of head grade fluctuations. The test program was carried out on one of two parallel copper flotation circuits to allow comparison with normal "manual" operating control, and was conducted for thirty eight shifts. Results from the test section operating under Simplex direction were superior to those obtained using normal "manual" operating techniques and demonstrated the use of the Simplex Evolutionary Operation Technique as a method of reducing reagent consumption in flotation but, at the same time, maintaining satisfactory metallurgical performance. Experience in the use of the technique indicated the need for modifications to the rules of Simplex operations. Modifications were proposed, tested and appeared satisfactory.

Jan 1, 1973

By Kobayashi M

Particulate chalcopyrite samples (78 ~ 98 mole per cent chalcopyrite, screen size fraction from 710 to 250 µm) were prepared by crushing and sieving lump ore samples from 12 locations in the Mt Isa Mine. Measurements of thennoelectric power (which does not involve the passage of a current) were made using a packed bed that was compressed by loading with a weight and placed in a temperature gradienL Details of the apparatus are described.The effect of particle size was investigated by preparing 12 fractions, with mean particle sizes ranging from 605 to 2.2 µm, from one of the ore samples. Values of thennoelectric power decreased with both increasing particle size and loading pressure; however it remained fairly constant for particle sizes above 80 µm, when loading pressure exceeded 3.3 MPa.Measurements of the chalcopyrite samples gave an average value of -260 JlV/K (-248 ~ -268 µV/K) for nine samples and about -290 µV/K for three samples, showing that these samples were all n-type semi-eonductors.

Jan 1, 1990

By Geisler P, Sutherland P

The technical limits for high-pressure transport of large particle solids by means of sludge pumps, piston pumps or the like lead to the development of the pipe-feeder system. The pipe-feeder is a type of pressure lock in which the high-pressure pump itself is not in contact with the solids. Simultaneous operation of the three chambers with corresponding control of the valves allows continuous flow in both the primary and secondary circuits. Initially the pipe-feeder was used only for the transport of solids. Today it also operates with great success in central mine cooling systems, serving as an alternative for high-pressure/low-pressure heat exchangers or Pelton systems. In addition to the technology applied up to now, the pipe-feeder is also capable of transporting ice slurry, thus increasing cooling output consider- Ably.

Jan 1, 1991

By B J. Monaghan, P Zulli, X F. Dong

In the lower zone of blast furnace (BF), slag trickles down through a packed bed of carbonaceous particles in the form of films, rivulets or droplets. During its downward flow, there are significant interactions occurring between slag and other phases, ie gas and packing particles. In particular, the interaction between gas and slag is closely associated with the key flow phenomena such as loading, flooding or channelling in the lower zone of the BF. With gas introduced laterally through tuyeres and slag flowing downward from the cohesive zone to the hearth, this interaction varies throughout the lower zone and in the cohesive zone:  strong cross-flow of gas relative to the slag occurs in front of the raceway  counter-current flow of gas and slag occurs in the upper parts of the lower zone  both strong cross- and counter-current flow of gas and slag around and within the cohesive zone. These interactions can be linked to furnace irregularities, affecting smooth operation and limiting production. Therefore, understanding the gas-slag interaction and its influencing factors remains critical for BF process control. In the current review, the physical behaviour and key influencing factors of gas and slag flow are initially examined. Numerical models describing gas and slag flows in a packed bed at micro-, mesoand macro-scopic levels, are reviewed. Each simulation approach has its advantages and limitations, as well as unique assumptions when used in BF process modelling. Applications of these approaches to gas-slag flow in key identified functional zones will highlight the differences between approaches and modelling outcomes. As no single approach can fully address all aspects of gasslag interactions, an integration of different approaches is considered an effective and beneficial method in providing a more complete understanding of gas-slag flow in the BF process.

Jun 19, 2024

THERE are few industrial and metallurgieal processes which do not require the application of heat energy, and the modern demand for increased working efficiency has resulted in attention being paid to temperature control as a means of ensuring fuel economy and more efficient plant operation. In general, mill accuracy required is not very contant in laboratory work, and few industrial operations are controlled to within less than 5° while in many cases greater limits are allowable. Almost every thermal property of matter has been suggested as a basis for the construction of pyrometers, but the thermo-electric type finds by far the widest application, and hence this paper will deal only with the principles, construction, and uses of this type of instrument. THERMOELECTRIC PYROMETRY.In the year 1821 Seebeek discovered that if the ends of two dissimilar metal wires were joined and one junction heated, a current flowed in the circuit, and the KMF (electro-motion force) set up could be measured by inserting a galvanometer at the cold junction. The phenomenon was not thoroughly investigated for many years, but, as the demand for high-temperature thermometers increased, several investigators, of whom Le Chatelier was one of the pioneers, successfully endeavoured to utilize the principle in pnometric construction. The couples which gave the most satisfactory results were discovered, improvements were made in material and design and the present-day type of instrument gradually evolved. The apparatus consists of three main parts, viz. (1) The thermo-couple itself of two dissimilar metal or alloy wires together at one end. (2) The leads which connect the terminal of the thermo-couple with the measuring instrument.

Jan 1, 1923

Future hard rock mining will gradually move towards complete mechanisation which lends itself to remote control and ultimately to robotic mining. This will require different technical inputs into mining engineering and one of these is in the area of rock'mechanics. Traditional hard rock mining has had little rock mechanics input. Problems arising from high stresses and poor ground conditions have in most cases be remedied after they occurred, in the worst case by abandoning a particular stope or area and starting elsewhere. In a fully mechanised remote or robotic mining situation the financial penalty for such an approach could be severe, as a major part of the production costs will be in the development and the equipment. It is therefore imperative that a complete rock mechanics feasibility study is undertaken before an area is set up for robot mining and that a continuous stability monitoring system is installed that will predict rock behaviour well in advance of mining, such that the necessary ground control measures can be implemented without impeding the continuity of mining. This system will utilise already existing instrumentation such as extensometers and stress cells, and possibly additional improved instrumentation which has to be developed for this particular Application.

Jan 1, 1986

By D Thomas, B Gallagher

Valuable data for geotechnical interpretation and integration into effective Australian underground mine planning may often be available, yet is not always fully appreciated or utilised, particularly in the early stages of mine planning or in due diligence studies. There may be considerable benefits associated with early prioritisation of geotechnical evaluation and impact on mine planning. Unidentified, misinterpreted, or ill-defined adverse geological and related geotechnical resource characteristics can pose significant business risk to underground coal projects and operations. Preliminary resource definition in the early conceptual mine planning stages attributes significant focus (entirely warranted) on resource quality and structural geology constraints. Yet detailed geotechnical data analysis and interpretation, which may have a substantial down stream impact and sensitivity with respect to future mine planning strategies, at times is given lower priority, or scoped and resourced in the later stages of a bankable feasibility study. Through extensive mine planning experience and observation of downstream process impacts, it has been found there is often data available for geotechnical analysis that does not readily stand out or is not adequately understood or utilised, available at the early (conceptual) stages of mine planning. Part of the issue may be that exploration geologists are not necessarily experienced geotechnical engineers and do not necessarily recognise or understand all important parameters. Subject to appropriate application of experienced professionals data can be manipulated to provide key geotechnical hazard assessment at minimal cost, and provide a framework for understanding and optimising the mine planning process. Although there is no single prescribed strategy for resource evaluation from a geotechnical perspective, potential business risks and mitigation approaches can and should be adopted at the conceptual mine planning stage. There has been a recent focus in the metals industry to provide a reporting framework for geotechnical classification of mining projects. This paper outlines the strategies and gives examples of key analyses adopted in mine planning and discusses the relative merits of adopting a reporting framework as a tool for geotechnical classification in mine planning.

Jan 1, 2005

A laminar-flow furnace was used to study the combustion of four flotation concentrates (chalcopyrite, pyrite, galena, and sphalerite) in air at temperatures up to 1400¦C. A special- Iv developed two-colour pyrometer was used to measure the temperature of individual chalco- pvrite and pyrite particles as they underwent combustion. Chalcopyrite and pyrite ignited with very high rates of reaction at air tempera- tures above 480 and 600¦C respectively, forming molten products. Galena and sphalerite required temperatures in excess of 700 and 1200¦ respect- ively to attain equivalent rates of reaction. The high rates of reaction for galena and spha- lerite were caused by vaporization. Temperature measurements for chalcopyrite and pyrite are reported here, together with vaporization measurements for chalcopyrite, galena, and Sphalerito

Jan 1, 1980