Search Documents

By Robinson WB

An accurate and rapid assessment of coal resources, such as that provided by computer modelling, forms an intergral role in evaluating CSR's coal deposits for future development. An in-house system utilising a number of geological, engineering, costing and financial evaluation routines has been developed for DEC VAX computers. The system is currently being upgraded and enhanced to meet the demands at the various mine sites. Computer modelling of the geology is performed on encoded drillhole information and coal core chemical and physical analyses. A conceptual mine plan is formulated then digitized and superimposed on the geological model. Insitu and product coal reserves and qualities as well as overburden and parting quantities are then calculated for each strip or block. These strip parameters are then transferred to the mine scheduling routines to determine the most efficient mining sequence for the mine plan. Cost factors and scheduling data for equipment specified in the conceptual mine plan are used in the mine costing subsystem. The financial subsystem then evaluates the likely return on investment. Future enhancements to the system include improvements in the response time through the introduction of interactive graphics, the direct interfacing of geophysical and analytical data, and further development of a geotechnical'database.

Jan 1, 1983

By Iley J. D

The production of zinc from low grade concentrates, particularly those high in iron, has a poor economic return due to a combination of higher concentrate transport costs, increased processing costs and an increased cost for disposal of iron residues. The production of iron-bearing residues from the electrolytic zinc process is also seen as undesirable for both cost and environmental reasons. This paper details the pilot plant testwork conducted at the Pasminco Research Centre in conjunction with Minproc for the production of zinc oxide fume from a high-iron zinc sulphide concentrate from Colquiri in Bolivia. The concentrate is derived from a tailings retreatment operation and has a high iron content (40 - 45 per cent Zn, 14 - 17 per cent Fe) due to the presence of marmatite. Pilot plant trials were conducted using the slag bath reactor at Pasminco Research Centre at rates up to 500 kg/h of pelletised zinc concentrate, using a natural gas/oxygen-enriched air lance. The fume produced averaged 76 per cent Zn at recoveries up to 96 per cent and was recovered in a baghouse after gas cooling. The iron was oxidised into a fayalitic slag that passed the TCLP test (toxicity characteristic leaching procedure) and the sulphur was oxidised to produce a high SO2 gas which would be suitable for sulphuric acid production. The process produces a zinc oxide fume that can replace calcine as a feed for electrolytic zinc plants. The iron reports to a stable slag for disposal, thus eliminating the need for its disposal as jarosite from the leach plant. Only a simple leaching operation on the fume is required as there is no zinc ferrite present.

Jan 1, 1993

Proposals designed to use stockpiles and buffer stocks to achieve price stabilization and better resource use have a long history. They are super- ficially simple to understand. The benefits seem clear. And yet I am well aware that this is not a simple subject: the more one studies it, the more complex it becomes. Worldwide interest in re- source management, while receiving fresh impetus from the OPEC actions, also has a long and chequered history. Those venturing into such ter- ritories must be forewarned of the traps and pit- falls which abound. Interest in these schemes has waxed and waned over the years with the fluctuating fortunes of the producers or consumers. As I write this paper towards the end of 1977, I am acutely aware of the low ruling prices for zinc, copper, and nickel. These sacrifice prices remind me that it is difficult, for example, for a surveyor, to be calm and rational if he is up to his neck in a swamp full of crocodiles. He might be forgiven for forgetting that the aim was to drain the swamp! I am also aware that when swamps are drained, painful and dangerous stumps sometimes stick out. Hence, in looking at the subject of stockpiles and resource management we must not set our sights too high, perhaps not initially hope for perfec- tion, if we want to secure worthwhile changes. My approach is to acknowledge a bias for the market system. We have, however, had experience (remember the 1930s) of some weaknesses in the untrammelled operation of free markets. Thus our international economic relationships over the past 20 or 30 years have been based on a desire to retain as much as possible of a liberal world trading system backed by such organizations as the GATT, IMF, and the U.N. to ensure the necessary cooperation. Some nations have seen this system work only partially in their best in- terests. GATT, for example, has been reasonably effective in liberalizing trade in many manufac- tured goods but far less so in regard to agricultural or semi-processed goods.

Jan 1, 1978

Based on twenty years of experiences of applying computers in mine water engineering in Hungary, a program package was developed for home utilization and for other users abroad as well. This program package has been adapted to the CAD System of Coal Mining of COMECON countries. The main features of the "mine water subsystem" in the CAD System of Coal Mining and short descriptions of the key programs of the package are presented in this paper. Foreword The serious water problems of Hungarian mining pressed and/or stimulated its professionals to apply computers for supporting their problem-solutions. The first trials of these computer applications in mine water engineering were dated from the sixties. Owing to its twenty years of experiences in computer appli- cations in mine water engineering the Central Institute for the Development of Mining in Hungary was requested to work out the "Subsystem of Mine Water" for the Computer Aided Design System ('CAD) of Coal Mines in COMECON countries. This paper gives a brief presentation on the main features of this "subsystem"with reference to significant components.

Jan 1, 1988

By Hood M

Rock cutting excavation technologies and particularly continuous excavation technologies, can offer benefits in the areas of reduced costs, higher revenue and increased safety in a variety of mining situations. Non-explosive rock excavation technologies for example, can deliver significant benefits in the areas of dilution and improved ground support (no overbreak). This paper is an attempt to focus on the development and future of alternative rock breaking technologies and to provide some insights as to why and how we should proceed in this direction. The market size for underground hard rock excavation technologies is examined. A short review of the evolution of various rock excavation technologies in terms of cost and production rate is given and a summary of the state-of-the-art technology is presented. Mechanical excavation technologies (TBM) have very high production rates compared to D&B and the gap is widening, however, they have not been successfully applied to mining applications. Operating costs for mechanical and D&B systems have been dropping over time, however, D&B costs are the lowest. Given the current state of knowledge it appears that with regard to hard rock underground metalliferous mining that R&D efforts should be focussed in the following areas - disc cutter tool development (materials and design; operation; presentation to the rock surface), hybrid cutting systems (consisting of water jets and disc cutters) and development of pressurised hole breakage technologies. It is also possible that two techniques known as the pulsed laser and pulsed water jets may have some potential. The generally agreed specifications for a widely applicable underground hard rock excavating machine are - disc cutter based, a minimum production rate of 100 t/h, be flexible, manoeuvrable and deployable, weight of less than 100 tonnes and be economically competitive with D&B in rocks over 150 MPa UCS. Such a machine would seriously challenge the position of conventional D&B in a wide range applications and provide some of the benefits of mechanisation and automation that the mining industry is pushing so hard for. However, technology developments in the D&B area are not static and hence the target is moving and is increasingly difficult to overtake.

Jan 1, 1995

By Chapman G. J

Mining operations require detailed and precise methods and procedures for the optimum selection of ore from waste. A fundamental procedure applied to achieve this selection is accurate sampling. The key parameter to accurate sampling is an understanding of the degree of heterogeneity of the key element contained within a sampling mass. This paper will describe the methods applied for the calculation of the fundamental sampling error and the techniques used to achieve a representative sample in the Fimiston Open Pit, Kalgoorlie.The utilisation of Pierre Gy's sampling theory has optimised the blast hole sample quality and quantity for submission to the assay laboratory. This has resulted in reduced cost and optimised assay reliability in statistical terms. Similarly the analysis of exploration drill holes for resource definition has optimised drilling procedures in terms of the drilling method, sample length and sample quantity.

Jan 1, 1993

By G J. Jameson, A Agarwal

This paper is concerned with the observation and analysis of bubble clusters in a laboratory flotation cell. A device was used in which bubbles were allowed to rise in clean water containing the same frother and collector concentration as in the cell. Bubble clusters were recorded using a high speed camera and analysed using an image analyser. Dodecyl amine was employed as a collector to float silica. The effect of impeller speed on the cluster behaviour was investigated. The results were interpreted in terms of cluster diameter and shape factor. The sizes of the bubbles forming the clusters were also measured and compared to the sizes of the independent bubbles in the cell. It was found that there was an optimum impeller speed in which the cluster diameter was a maximum. Higher agitation and the consequent higher power inputs resulted in cluster break-up while lower shear rates promoted cluster formation.

Jan 1, 2005

Published information on technical and market developments in the uses of zinc tends to dwell very largely on two groups of uses of zinc - zinc coatings (mainly galvanising) and zinc casting alloys. These two groups account for two-thirds of primary zinc consumption. However, if total zinc consumption is taken into consideration, coatings and casting account for a little over half the total. Either way, the health - or otherwise - of these 'other' uses of zinc can have a substantial effect on the industry as a whole. The aim of this paper is to put the whole market picture for zinc into better focus, concentrating on the factors which can affect consumption in the 'other half' of zinc's markets: ò brass - the third most important market for zinc at around one million tonnes - responds to changes in the economic cycle. It has seen substantial changes in the balance between different forms of semi products, and, in Europe at least, some real market gains; ò zinc sheet - one of the original uses of zinc in Europe - has grown substantially in some countries, but remains almost unknown elsewhere; and ò zinc pigments and compounds are so numerous that - barring the substitution of zinc oxide in rubber - major overall changes in the market are unlikely. The paper examines these markets and assesses their potential and implications for zinc markets as a whole.

Jan 1, 1993

By Riley S. J

Ranger Uranium Mine is located within the Alligator Rivers Region of the Northern Territory of Australia and surrounded by the World Heritage listed Kakadu National Park (Figure 1). The mining operation is currently producing about 1500 tonnes of uranium oxide annually, as well as considerable volumes of waste rock, low grade ore and tailings. The rehabilitation of the project should ensure that the radioactive mill tailings and other contaminants remain contained for at least 200 years, as required by the existing guidelines (Commonwealth of Australia, 1987). The present uranium mining operation is regulated by the Northern Territory Department of Mines and Energy who must refer to the Environmental Requirements when considering regulatory options. These Environmental Requirements were agreed by the

Jan 1, 1994

By Schoning W. L

Ore deposit models form the basis for numerous other economic decisions in the mining process. The success of these economic decisions therefore depend directly on the accuracy of the ore evaluation process. The Geology Department at the Sishen Iron Ore Mine is responsible for the generation of a reliable geological computer model of the rock material with predicted grades. This information is then utilised for further ore reserve calculations, mine planning, production scheduling and grade control. Owing to a very complex geological orebody, grades and beneficiation characteristics differ significantly from sample to sample. This means that ore evaluation is a difficult process and great reliance is placed on computer techniques. In 1993, preparation for the ISO 9002 quality certification of the mine motivated the Geology Department to hold formal `problem solving' sessions in order to identify and revise problem areas in operating

Jan 1, 1995

By S Arthur, J Mills, A R. Penney

A key aspect of seismic management for narrow vein stoping of the west zone at the Beaconsfield Gold Mine has been the development of a fully remote extraction method that does not require personnel access to sill drives within the orebody once stoping commences. Initially, sill driving within the reef is undertaken in a conventional fashion under geological control. Sill drives are developed at a vertical backs-to-floor height ranging from 7 - 12 m. This mining stage includes all activities prior to the commencement of stoping, after which no personnel enter the unstoped section of the sill drive at any time for any purpose. The key aspect of the remote mining cycle is the use of footwall drill drives paralleling the ore drive at a minimum separation of 6 m under survey control. These drives provide the platform for fan drilling of the orebody. Up to 20 m strike panels are blasted in a single shot using electronic blasting techniques. Ore is mucked from the extraction level sill drive using tele-remote loaders. Aerials for tele-remote operation are installed through boreholes from the footwall drive, negating the need for personnel access to the sill drive. Once mucking of a stoping panel is complete, a laser scanning survey instrument is used to survey the final void for subsequent design and production reconciliation purposes. The survey instrument is mounted in the bucket of the tele-remote loader, and is also operated remotely. Finally, tele-remote loaders are used to dump waste rock fill from the upper sill drive. A system of flags and cameras installed in boreholes from the footwall drive assists the operator in locating the live stope edge during the filling cycle, again negating the need for personnel access.

Jan 1, 2008

Longwall mining has historically been considered an application for only deep reserves. This has changed in the recent past as longwall has become competitive with surface mining. Many resources marked for stripping now he in the domain of longwall. Today, the best longwall mines compete with strip mines operating in even the lowest stripping ratios. Longwall mining has become more widely applicable than it ever has been in the past and it is now generally considered the method of choice in situations where high levels of coal production are required. But the best way to use longwall mining has become less certain with the opportunities that highwall access provides. Wall-to-wall mining is the use of retreating longwall developed from and retreating toward a highwall. As a surface mine reaches its ultimate highwall, the opportunity for longwall punch mining or wall-to-wall mining is obvious. There are several clear operating advantages to operating a longwall in this way and where highwalls are available, the best economic decision will generally favor planning a direct approach. Yet wall-to-wall is not applicable in every situation even when highwalls are available. Moreover, the advantages of wall-to-wall mining do not always justify the cost of trenching or box cuts to access coal . However, many tactical advantages of operating from the highwall can be realized with the use of specially equipped blind drilled or raised bored shafts. This paper discusses novel techniques for a shaft assisted mining system which permits the addition of conveyor structure and mine systems from the surface to the face for advance and retreat mining with longwall, shortwall or room and pillar panels.

Jan 1, 1998

By Storey AG

Following initial plant scale work on the development and performance of 'spray' oil lances, a full scale room temperature model of the blowpipe-tuyere region of a blast furnace was built to study the basic aerodynamic features of auxiliary fuel injection procedures. Mobilwax 2305 was used as a substitute for Bunker C oil fuel in view of its similar physical properties and the fact that the atomised droplets could be frozen in flight and size, distribution analyses made for various operating procedures. It was shown that secondary atomisation processes far outweighed the importance of any primary atomisation procedures in determining mean Sauter Diameters particularly at high windrates typical of current blast furnace technology. It was also found that good spray dispersions across the blow pipe could only be obtaind for liquid fuels and that the lateral rate of spray dispersion was substantially enhanced by primary atomisation procedures. Mean particle diameters of sprays were found to be predictable on the basis of elementary stability theory and fell within the size range necessary for good combustion at all liquid fuel rates studied. The possible effects of high oil injection rates on flooding phenomena in the furnace bosh were considered. Comparisons show that high oil rates can lead to significant increases in the hanging factor (e.g. 'V 10% at 135 kg oil/thm) owing to increased gas flow rates/thm resulting from the presence of hydrogen.

Jan 1, 1975

By Turco E, Pelizza S, Castellani F, Stanganelli V

Excavation are in progress for the building of tunnels of the waterworks in West Campania (Naples). The works afferent to part II envisage tunnelling through a miocenic clay formation over consolidated by two tunnels whose sections are respectively 50 and 10m2. Tunnel blasting is carried out by mechanical means. An excavator is used in the big tunnel, whereas in the small tunnel a roadheader machine is used for a short tract and a mechanized shield is used over a long stretch. The tunnel feature complex problems regarding stability. This is particularly so for the big tunnel whose face appears unstable. For this reason the clay on the face is sistematically bolted by means of 3-metre and 12-metre bolts. This prevent the use of a TBM for tunnel Excavation.

Jan 1, 1987

The methods used by the Anglo American Corporation for analysis of long-term metal markets and prices are described. The principal factors affecting the relationships between production costs and metal prices are analysed. These are firstly the type of market, - speculative or consumer commodity, free market or subject to price control; and secondly the rate of growth of demand for the metal. It is shown that virtually all metals will have relatively low rates of demand growth for the foreseeable future, due to market saturation, increased economisation, substitution and product obsolescence. Metal prices have a clear dependance on production costs, however forecasting future costs is by no means simple; amongst other things, account must be taken of changing exchange rates, inflation rates, and the potential for operating more efficiently. The paper concludes by giving brief assessments of the long-term future for aluminium, copper, zinc, nickel and tin.

Jan 1, 1986

By Wilson AC

Permian coal from Western Australia's only producing coalfield at Collie is the dominant fuel used in generating electricity for the State's interconnected grid. Collie coal is sub-bituminous, non-coking and has a low ash, medium volatiles and high moisture content. The seams were laid down in a fluvial basin which extended beyond the Collie Basin and included the Wilga and Boyup Brook Basins at least. Adjacent parts of the southwest Yilgarn Block are prospective for Collie-type basins. In the past few years significant deposits have been delineated within the Perth Basin, specifically on the Vasse Shelf and in the Hill River area. In the former area high quality steaming coals are correlated with the lowest coal bearing member at Collie. The seams are amenable to underground mining and because of their high quality, the coal may have export potential. Sub-bituminous coal deposits of Jurassic age are present in the Hill River area. Exploration has down-graded the prospectivity of the Carnarvon and Canning Basins for sub-bituminous near-surface coal deposits. Tertiary lignite deposits are present in palaeo-drainage systems in the southern part of the State and their potential for development is being evaluated.

Jan 1, 1986

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C M. Côte, P Bolz, R Chrystal

The design of final landforms is an integral part of mine closure plans in Queensland and aims to ensure the rehabilitated land is safe, stable and non-polluting. Landform stability in this context is commonly assessed using Landscape Evolutions Models (LEM) which are physical models simulating sediment erosion and deposition around individual landforms over long timespans (up to thousands of years). The most used LEM for assessment of rehabilitated landforms in Queensland is SIBERIA (Willgoose, Bras and Rodriguez-Iturbe, 1991; Tucker and Hancock, 2010). SIBERIA models are complex, require very detailed input data and simulate erosion and deposition over time frames that extend decades beyond closure. They are not suitable to assess erosion risks during the operational phase of a mine and to support the development of erosion and sediment control plans. Other types of erosion models, such as the Revised Universal Soil Loss Equation (RUSLE, Wischmeier and Smith, 1978) or Water Erosion Prediction Project (WEPP, Nearing et al, 1989) calculate soil loss on a monthly or yearly basis and are much better suited to erosion management during the operational phase. They are simpler to implement and can support the design of control measures. For instance, designing a sediment basin requires quantification of sediment loads, which can be produced by these models. In Queensland, the legislation around sediment and erosion control for open cut mines is currently tightening. Soil erosion remains a major concern due to potential impacts on the receiving environment. It requires management during operation and for closure consideration alike and it is critical that erosion and sediment control plans are developed with the most appropriate tools. Globally, RUSLE is the most widely used soil loss model (Borrelli et al, 2021). This is because it is an empirical model with relatively simple input requirements: biophysical data such as soil properties, vegetation cover, topography and rainfall variability, which can be directly measured or derived from regional or national databases and/or spatial data sets that are available in most parts of the world. The second most used model is WEPP (Borrelli et al, 2021) but compared to RUSLE, there is a large drop in the frequency of its use. This is because WEPP is physically-based and has more complex data requirements. WEPP integrates hydrology, hydraulics, erosion mechanics and land cover to predict soil erosion and sediment transport on hill slope profiles and small watersheds (Stolpe, 2005). It requires some biophysical parameters in formats different from those of RUSLE, as well as detailed hydrologic and catchment data. Nevertheless, it has been used in landform design for mines across Australia to determine final landform stability (eg Howard and Roddy, 2012; Costin, 2020). In this study, we assess which tool would be the most appropriate to support development of erosion and sediment control plans from operation to closure. We use RUSLE and WEPP to predict soil loss from a mine site, compare the results from both models and outline the advantages of each method.

Aug 2, 2023

By Savidis G

The characteristics of 'Z' (Back-over run) and 'R' (Reverse) ventilation systems are dis- cussed in relation to their suitability for longwall mining. Experience in European mines has been described as a basis for comparison with Australian conditions. In assessing the merits of each ventilat- ion system, such factors as longwall layout (pillar design, number of headings and gateroad stability), the need for gas drainage and bleed- er systems, as well as the influence of seam dip have been considered relevant. The R system is generally applicable for single and two heading development in seams where gas emission is a less serious problem. In contrast, the lower extraction to development ratio of the Z system (which arises from using three or more heading layouts) is considered more favourable where high gas emission occurs. The Z system provides greater flexibility with respect to the provision of refreshing air at the tailgate end, access of men and materials, installation and retrieval of gas drainage systems and the ability to interchange main- gate and tailgate roadways in cases where roof strata loads are difficult to control, or where cpam in hac an influrnra

Jan 1, 1983

By N Voller, A Ishmurzin, G Hackl, M Wu, A Kharicha, M Chintinne, C M. G Rodrigues, A Ludwig

Slag fuming (SF) is a critical process for recycling zinc-containing slags, but the corrosive nature of molten slag poses challenges to the reactor durability. The freeze-lining (FL) technique offers a solution by forming a protective layer on the reactor wall. It requires intensive cooling using watercooled jackets, which can stabilise the FL while compromising the energy efficiency of the process. This study presents a computational fluid dynamic (CFD)-based model to optimise the SF process by considering FL formation and its impact on heat transfer and reactor wall temperature. A volumeof- fluid (VOF) model is coupled with a mixture continuum (MC) solidification model to capture the intricate multiphase flow dynamics within the SF furnace. Two FL types are considered: FL solidifying on the reactor wall in the slag bath region; and FL solidifying on the reactor wall in the freeboard region. The FL of the first type forms when the slag temperature drops below liquidus temperature. The FL of the second type only forms when a splash-induced slag droplet collides with the freeboard wall and solidifies. A series of splashing events are necessary to coat the freeboard wall. The simulation was run until a global energy balance was reached. This means that the heat losses from the water-cooled jacket, bottom wall, outlet and fuming balance the heat gains from the hot gas injected through the submerged plasma torches. The increase in FL thickness, due to its low thermal conductivity, reduces the heat losses through the reactor walls. The calculated FL thickness and heat fluxes were in good agreement with industrial data, validating the model’s credibility. The simulation results provided valuable insights into the fuming process, including slag bath temperature evolution, slag splashing dynamics, FL formation patterns, local heat fluxes through the reactor wall and overall energy balance. These findings can inform process optimisation strategies to enhance the energy efficiency and sustainability of SF operations. The authors have built a prior version of the model framework and applied it to simulate FL formation in an electric smelting furnace (ESF). The results from both the ESF and the current SF highlight the applicability of such model framework to a range of industrial processes involving FL formation. This model framework can ultimately contribute to more energy-efficient and sustainable industrial operations.

Aug 21, 2024