Search Documents

By Taylor R. K A, Berglin C. I K

The manganese ore deposits at Groote Eylandt are quite variable both in regard to grade and physical cond- ition. In order to treat a wider range of these ores and to increase production a new primary-crusher and' concentrator complex costing $8 million has been installed and commissioned to treat ore at the rate of 12,000 tonnes per day. The initial testwork carried out to determine the method of the ore treatment required, and on which the design of the concentrator was based, is detailed. The flowsheet and equipment used is discussed together with the operation of the plant. The production achieved and product qualities obtained are given.

Jan 1, 1973

By Spencer PA, Winborne DA

The Porgera mineral deposit in Papua-New Guinea contains gold as finely divided, probably submicroscopic (1 um) particles dispersed in a pyrite sulphide matrix. Only 25-30% of the gold in pyrite can be extracted by direct cyanide leaching and fine grinding the pyrite does not increase gold extraction significantly. This work is concerned with the application of alkaline leaching at atmospheric pressure to oxidise the pyrite prior to gold recovery by cyanidation. The paper presents and discusses results of a comprehensive set of testwork using sodium carbonate, sodium hydroxide and calcium hydroxide alkaline media. Best results, at 60-70% gold extraction, were obtained with sodium hydroxide systems.

Jan 1, 1984

The passage of a vast array of new State and Federal environmental legislation over the last couple of years has required many mine operators to sharpen their focus on environmental requirements. Established requirements, such as environmental impact assessment, minimising disturbance and rehabilitation must now be complemented by mine environmental management plans. These may not only require regular monitoring of mine operations and detailed forward planning to prevent or reduce environmental harm caused during mine operation, but annual updating. It is likely that in future these plans will be required to incorporate general principles such as pollution prevention, sustainable development, waste minimisation and conservation of biodiversity and ecological integrity.

Jan 1, 1993

The New South Wales Department of Mineral Resources has, since 1974, administered the Derelict Mines Rehabilitation Program (DMRP) to reduce the environmental impacts of abandoned and orphan mine sites. The application of the DMRP is presented in case studies of sites from the South Maitland Coalfield featuring residual drainage of acidic and saline water in a semi urban and rural community setting. The acidity here is typically derived from iron oxidation in shallow underground coal mine workings and in surface emplacements of coal washery reject materials. This paper presents summary information on AMD investigation, monitoring and rehabilitation. The experiences of community expectation, stakeholder consultation and peer review are discussed.

Jan 1, 2003

By Mernagh T, Large R. R, Ryan C. G, Huston D. L

The Tennant Creek goldfield is one of the largest gold producing districts in Australia, and major deposits, including Gecko, Juno, Orlando, Peko, Warrego, Nobles Nob, Golden Forty, Argo, TC 8 and White Devil have produced more than four million ounces of gold over the past two decades. Gold-copper-bismuth mineralisation at Tennant Creek occurs in lenticular, ellipsoidal or pipe-like bodies of magnetite-hematite ironstones which are hosted in turbiditic sedimentary rocks of Proterozoic age (Large, 1975; Wedekind, Large and Williams, 1989; Le Messurier, Williams and Blake, 1990; Morrison, Donnellan and Hussey, 1992).

Jan 1, 1994

By J Chen

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled stopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench stope fill mass is described and a technique for reducing the potential for bulkhead failures in bench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also described.

Jan 1, 1998

By D Craw

Quaternary warping and uplift of antiformal schist ranges in Central Otago, New Zealand, has resulted in recycling of alluvial gold from widespread, generally weakly auriferous, Miocene fluvial gravels that unconformably overlie the schist, into aprons of fan sediments along the range margins. Basement erosion during uplift has been limited and so gold input from sparse gold-bearing quartz veins in the schist has been relatively minor. In an eluvial cycle on the slopes of the ranges, chemical remobilization of gold occurs during oxidation and erosion of the Miocene sediments. The typically fine-grained (300 - 400 ¦m) gold undergoes chemical modification and grain size enhancement of up to two orders of magnitude, and much of it is redeposited in a large number of relatively small alluvial fans along the range margins. Groundwater mobility within the fans results in minor additional gold mobility and grain size enhancement. During range uplift, a small number of relatively large axial streams and rivers have developed in structural lows between growing antiformal folds. Axial streams 'gather' their flow from consequent streams draining the folds, and flow parallel to a range axis for some distance before cutting across it in an antecedent gorge. The axial streams rework alluvial fan sediments along the range margins, and transport mainly fine-grained gold from the fans along the ranges. This gold is redeposited where the axial streams emerge from a range in the neighbouring structural basin. Axial streams drain relatively large areas of range surface, and thus reconcentrate significant quantities of gold in a small number of relatively large fans and fluvial deposits. The processes of gold collection and re-deposition by axial streams are essentially the same, regardless of stream size. Coarse-grained gold produced by chemical remobilization, is more difficult to transport in fluvial systems, and thus remains in close proximity to eluvial environment where it was formed.

Jan 1, 1995

By B Hooper

Deep cuts in CO2 emissions will be required to stabilise and, in the long term, decrease CO2 concentrations in the atmosphere. Technologies for capturing CO2 from major stationary sources (power stations, industrial plants, etc) and storing that CO2 for long periods of time is one of few near term options for decreasing CO2 emissions. This transition to low carbon intensity energy and possibly the hydrogen economy through renewables and in the long-term technological developments such as artificial photosynthesis.Capture of CO2 from post combustion emissions can be done using a range of technologies though costs are currently high and dependent on the concentration of CO2 in the emissions. Techniques include solvents, pressure swing adsorption and the use of membranes. Options for decreasing capture costs by increasing the concentration of CO2 in the emission stream include the use of oxyfuels (in pulverized fuel types boilers) and by moving to integrated gasification combined cycle (IGCC) operations either simply for power generation or for poly-generation opportunities. Once the CO2 has been captured it can be stored using a variety of methods. Storage in the ocean has been suggested but is considered an unlikely option because of environmental uncertainties and political opposition. Mineral storage is a niche opportunity. The greatest potential lies in geological storage of CO2 and this option is commanding increased attention from the Australian and international community.In Australia, the Cooperative Research Centre for Greenhouse Gas Technologies (CO2CRC) is an important new initiative that will support energy companies and energy intensive industries in meeting challenges posed by greenhouse gas issues and assist them in their efforts to reduce their emissions profile.The progress of geo-sequestration and the challenges in the capture and separation of CO2 in the process industries are discussed.

Jan 1, 2004

By A Jafari, N Khalili, M Vahab, P Broumand

This paper presents the implementation of the eXtended Finite Element Method (XFEM) in the general-purpose commercial software package COMSOL Multiphysics for multi-field thermo-hydromechanical problems in discontinuous porous media. To this end, an exclusive enrichment strategy is proposed in compliance with the COMSOL modelling structure. COMSOL modules and physics interfaces are adopted to take account of the relevant physical processes involved in thermo-hydromechanical coupling analysis, namely: the mechanical deformation, fluid flow in porous media and heat transfer. The model preprocessing, level-set-updates, coupling of the relevant physics and postprocessing procedures are performed adopting a coherent utilisation of the COMSOL’s built-in features along with the COMSOL’s LiveLink for MATLAB functions. The capabilities and performance of the proposed approach are investigated by examining several multi-field thermo-hydro-mechanical simulations with reference to the block caving process in mines.

Nov 29, 2022

By R M. Hough, G Duclaux, M A. Pearce, M F. Gazley

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Microcharacterisation, such as that described in this paper, provides understanding of a mineral system at multiple scales, and understanding microscale variations is the key to understanding the large-scale variations in a mineral system. More than 50 high-grade lode samples from across Plutonic Gold Mine (Plutonic), Marymia Inlier, Western Australia were analysed by a variety of techniques, including micro X-ray fluorescence (µXRF) mapping, micro X-ray computed tomography (µCT), scanning electron microscopy (SEM), field emission gun SEM, electron back-scatter detector (EBSD), proton-induced X-ray emission microprobe and synchrotron XRF mapping. These data demonstrate that competency contrasts are the key to governing the location of Au mineralisation at Plutonic. Micro CT imaging of high-grade samples shows the Au filling in voids and pore-space in the rock, after having travelled along more permeable layers and already existing or reaction-induced pores formed during hydrothermal circulation. Using 3D visualisation, the Au is seen to form a connected network that appears undisturbed at the scale of the samples, and a high-grade Au deposition event was one of the last events to affect the rock. This interpretation is supported by SEM analyses on high-grade samples that reveal calc-silicate (epidote-clinozoisite) alteration that is not present in lower Au grade samples, which are typically dominated by potassic alteration, and that sulfides are typically less abundant close to the Au. The replacement of biotite by chlorite is an alteration associated with the high-grade Au-mineralising fluid. Gold is coarsest where Au particles are located on the margins of minerals, typically sulfide and quartz grains, suggesting the importance of rheological contrast at the microscale. Furthermore, EBSD data reveals that Au is undeformed and overprints peak metamorphic and retrograde minerals. Data confirm recent deposit-scale observations, suggesting that deposition of high-grade, visible Au was related to a hydrothermal fluid circulation event late in the geological history of Plutonic.CITATION:Gazley, M F, Duclaux, G, Fisher, L A, Hough, R M and Pearce, M A, 2015. High-resolution characterisation of gold mineralisation at Plutonic Gold Mine, Western Australia – evidence for the late-stage deposition of high-grade gold , in Proceedings PACRIM 2015 Congress, pp 51–58 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Coal mining in the Bulli seam in the Southern Coalfield in New South Wales has experienced the dangers of outbursts of coal and gas. These incidents present a major risk to the safety of mine workers and consequently a threat to the overall viability of the mining operations. Since the occurrence of a major outburst incident in the South Bulli Colliery in 1991 involving three fatalities, the primary contributory factors associated with coal/gas outbursts in the Bulli coal seam have been identified and a strategy for the management of the outburst risk has been formulated by the cooperation of mine operators, mine workers and the Department of Mineral Resources. Utilisation of risk management techniques in combination with modern gas drainage technologies and geological control methods have led to the formation of this effective outburst management plan. Clause 15 of the Coal Mines (Underground) Regulation 1999 in NSW has made it mandatory in an area of outburst to carry out mining in accordance with a code or guidelines developed for mining in outburst prone areas (DMR, 1999). In this paper an outburst management system is discussed which was developed for collieries in the Southern Coalfield that brings together all the available information including past experiences and risk management techniques in a documented form in order to maximise safety of mine workers. It is concluded that since the introduction of the outburst risk management systems in the Southern Coalfield in 1994 considerable reduction in outburst incidences have been experienced.

Jan 1, 2003

By G Chitombo

Mass mining methods have become the mining industry’s preferred way of extracting most of the world’s most important metal and mineral commodities. Given the rapidly increasing global demand for commodities, the requirement to increase the contribution of some of these (eg copper and gold) from underground sources also continues to grow. In the case of copper this contribution is needed by a number of major producers to supplement production from their ageing deep open pits. Satisfying this increased demand will require the design, construction and operation of more effective, higher capacity and larger scale mines which, in turn, will require enhanced mass underground mining techniques such as block caving (BC), panel caving (PC) and sublevel caving (SLC).It is now widely accepted that future discoveries of orebodies, which will be developed using these methods, are almost certainly to be much deeper than the deposits presently being mined in this way and made more challenging because of the likelihood that the associated grades may be much lower than currently mined. The design and mining of future large-scale cave mines (supercaves) will become crucial in order to extract full value from such deposits. An essential prerequisite of this will be a much improved knowledge of the deposit, ie Total Deposit Knowledge. In this context, Total Deposit Knowledge is the characterisation of the ore deposit and its surrounds at all scales and includes; rock type (lithology), the spatial orientation of a range of geological features or discontinuities, rock mass fabric knowledge, metal grade and distribution data, geometallurgical data (including alteration), geo-hydrology, permeability and porosity. This is the information that will be used, as now, to delineate geological and geotechnical domains and construct models, but with outcomes superior to those presently available. From this information better-informed feasibility study design decisions and performance predictions must be made. In summary more geological information and analysis is required and this needs to be aligned to potential mining and processing requirements much earlier in the project than commonly occurs.

Aug 22, 2011

By V A. Diemar

The Chatree Gold Project represents a greenfields discovery of metallurgically clean shallow gold mineralisation in a logistically simple terrain. Total Measured, Indicated and Inferred Resources are currently 31 tonnes of gold and 160 tonnes of silver. Gold occurs in an adularia-sericite epithermal system within quartz-calcite-adularia veins, breccias and stockworks. Host rocks are volcanic arc porphyritic latite-trachyte flows, their pyroclastic equivalents and volcaniclastics of upper Permian to upper Triassic age. The mineralisation was deposited in dilated zones during repeated reactivation of pre-existing structures. To-date five mineralised prospects have been defined by drilling with three reaching JORC Code Mineral Resources status. The project is in its definitive feasibility stage and is anticipated to be in construction during 2000.

Jan 1, 1999

THE South Mine. owned by the Broken Hill South Limited, occupies mineral leases 7 and 8 on the Broken Hill lode. The ore reserves are 4,250,000 tons, and the ore hauled for the year ended June, 1930, was 387,000 tons, the total to date being 7,840,000.The mine, down to the 1070-ft. level, is naturally divided into two sections, the northern and southern ends. Ore extraction is practically completed in the northern end to this horizon, while the southern end is developed ready for a concentrated attack.Fig. 1 shows the state of the 8215-ft. level, after connection to the new shaft.The levels above and below to the 1070-ft. level are in a similar condition, while below the 1070-ft. level the stoping has been confined to the north end, but not completed. The south end on these levels is also partially developed.The ore at present is hauled up No. 1 shaft, which is centrally situated to the present workings. This shaft was put into use in 1909, and in 20 years has had approximately 5,000,000 tons of ore pulled through it.The company, having proved the existence of large ore-bodies in the southern end of the mine, decided to sink No. 7 shaft. This is a six-compartment frame-set shaft (see Fig. 2) equipped with two cages and two 5-ton skips, the remaining compartments being utilised for electric cables, pipes, and ladders. The surface arrangements will include a steel head frame, electric winders, and breaker station.

Jan 1, 1930

By Stanojevic R, McGlinn PJ, Day RA, Levins DM

This paper reports the results of a number of studies that Ansto has carried out for mineral sands companies concerned about low-levels of naturally-occurring radioactivity in their products. Where measured levels of radioactivity have exceeded allowable levels, Ansto has used specialised techniques to identify the source and distribution of the radioactivity and investigated processing strategies to remove the Contamination.

Jan 1, 1993

By A Goldstone, M Fitzpatrick

Contemporary mine wastewater flows are subject to stringent water quality standards before discharge to local waterways. Strict criteria are often applied as a result of fears of extensive acid mine drainage; a feature of the many abandoned mine adits around the Coromandel, Central Otago, and the West Coast. In most cases the USEPA water quality criteria have been used to set treated wastewater discharge water quality standards. In future it is possible that the recently published ANZECC water quality criteria guidelines will be used for this purpose. The ANZECC guidelines also provide for the establishment of discharge criteria at specific sites, rather than accept the trigger values. The use of site-specific criteria for treated wastewater mine discharges was pioneered at the Golden Cross gold mine, near Waihi, in the late 1980s. The procedure used to derive water quality criteria was based on USEPA guidelines. In developing the Golden Cross criteria, only species that occur, or are similar to those that occur in the Waitekauri River were used. The mine commenced discharge of treated wastewater in 1991, and macroinvertebrate communities in the vicinity of the discharge point have been regularly monitored twice a year for the past 12 years. Despite fluctuations in community composition and abundance over that period, no permanent significant changes in the macroinvertebrate communities occurred between sites above and below the treated wastewater discharge. The success of the site-specific criteria at Golden Cross has shown how the application of this methodology can result in the protection of aquatic life while allowing for the discharge of treated mine wastewater.

Jan 1, 2003

By P Lamberg, M Lyyr, S Heimala, J Liipo

Since the introduction of froth flotation for industrial practice, the process has long been developed and improved by making cultivated guesses or by using trial and error methods to a varying degree. Fresh possibilities have emerged after development of new surface sensitive analysing methods and in situ electrochemical methods. Having had the possibility to combine different findings between science and everyday plant practice, Outokumpu has been able to develop a catch-all procedure to manage a flotation process taking into account the specific requirements set by different minerals in a slurry. A number of these procedures are available and offered globally to clients as part of a Plant Audit service. The Outokumpu Plant Process Audit (Process ef-X) concept comprises of mineralogical determinations from process samples and plant data analysis together with electrochemical process measurements using mineral electrodes. Automatic control loop analysis can also be included. The objective is to combine the results for a basis of flotation process improvement. Since this methodology has earlier been an in-house practice, it follows that the results are also reflected in the development and design of the OutokumpuÆs processing equipment. An increasing number of ores have a very intimate fine-grained texture and it may be physically impossible to combine high grade with acceptable recovery by a flotation process alone. For such cases, combinations of different hydrometallurgical û mineral separation û pyrometallurgical processes are available. Mineral specific information and chemical expertise of flotation technology can be utilised in development of other processes, as well.

Jan 1, 2005

By C V. Deutsch

"Geometallurgical variables often cause problems to conventional geostatistical workflows. There are many variables; some are compositional and some are non-additive. They often show: complex multivariate relationships undersampling relative to conventional grade variables unequal sampling; that is, all variables are not available at all data locations.A variety of approaches have been developed over the years, but geostatisticians remain mostly focused on modelling rock types and a few grade variables with an abundance of data. The problems are reviewed and a chained workflow is presented where appropriate techniques are employed in sequence to permit reliable spatial prediction of geometallurgical variables. The spatial models may be used to assess the value of additional data, for prediction of process performance, for improved mine planning and other optimisation tasks. The chained workflow will include data transformations such as ratios and normal scores that make the variables amenable to geostatistical modelling. Data imputation techniques to account for missing values are considered with special consideration to spatial correlation with the available data. Decorrelation techniques such as the principal components, min/max autocorrelation factors and projection pursuit multivariate transformation are employed to manage massively multivariate modelling. Full distribution modelling must be considered to avoid biases in the prediction of non-additive variables. The post-processing of geometallurgical models must be streamlined for robustness and efficiency. The precise workflow varies according to the specific purpose of the study. Guidelines and thoughts on best practice are presented.CITATION:Deutsch, C V, 2013. Geostatistical modelling of geometallurgical variables - problems and solutions, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 7-16 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By O Aydan, R Ulusay

Blasting is the most commonly used excavation technique in mining and civil engineering applications. Blasting induces strong ground motions and fracturing of rock mass in rock excavations. Particularly, high ground motions may also induce some instability problems of rock mass and structures nearby. Furthermore, it may cause some environmental problems due to noise as well as vibrations of structures near the populated areas. Furthermore, flyrocks is another major issue for the safety of people and damage to machinery and equipments when blasting is employed. In this study, the authors explore the ways how to estimate the ground motions as a function of distance, amount of explosive, number of holes. The ground motions were measured by stand-alone accelerometers developed by the first author and some empirical relations are developed. The effect of ground motions on the instability issues of benches such as sliding, toppling and rockfalls were investigated. Furthermore, the flyrock issue is investigated and some empirical relations to estimate the maximum distance of flyrocks from the blasting relations are compared and discussed. CITATION:Aydan, O and Ulusay, R, 2018. The ground motions induced by blasting in open pit lignite mines and its environmental effects, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 142–151 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

I have chosen this topic for my address with the intention of preserving a rather extraordinary record of recurrent additions of capital in the financing of one of the world's important silver-lead-zinc mines. The recitation of the trials and tribulations which fore-shadowed the rise of Mount Isa Mines to a position of relative prominence in the realm of non-ferrous mineral production may, I hope, be of assistance to some of the younger members of the Institute who may be called upon during their careers to meet similardevelopmental and financial problems.Mount Isa Mines Limited was incorporated in New South Wales in 1924 with an Authorised Capital of 40,000 shares of £20 each.In November 1925 the Company acquired the leases and water rights of the Mount Isa Proprietary Silver-Lead Limited for 6,250 fully paid £20 shares. Shortly thereafter, but in the same year, the £20 shares were split up into £1 shares, thus bringing the Authorised Capital to £800,000.The leases purchased consolidated and brought under one management the principal ore bodies of the Mount Isa area.Transportation facilities were indispensable to the economic future of the field, so the construction of a railway extending the Government line from Duchess, 54 ,miles to Mo.unt Isa, was assured by the passage of a bill in October 1925 by the Queensland Parliament. Under the provisions of the so-called Mount Isa Railway Act the Company was required to idemnify the Government against national loss on this branch line for a period of 10 years.

Jan 1, 1953