Search Documents

By T J. Sheer

Water vapour refrigeration (systems using water as the refrigerant) could potentially be used to provide chilled water at underground locations in mines, as an alternative to conventional refrigerators using refrigerants such as R-134a. The use of water as both the primary and secondary refrigerants is attractive in concept since direct-contact heat exchangers could be used, yielding higher coefficients of performance. The disadvantage of water is the very high specific volume of the vapour at low pressures, which leads to great challenges in compressor design, as has been reported previously in the context of slurry-ice plants for mine applications (Ophir and Koren, 1999). Steam ejectors have long been known as alternative compression devices for refrigerators, but no work has been done previously on the possibility of using ejectors powered by high-pressure water, which is readily available in mines from long pipe columns in vertical shafts. This paper presents the results of a laboratory investigation into the use of high-pressure water as the motive fluid in an ejector refrigerator. No previously reported liquid ejector system has achieved subcooling of the process fluid, ie a reduction in fluid temperature within the evaporator to a level below that of the motive fluid. In contrast, the present work demonstrated that subcooling could occur at motive water pressures above 5 MPa. Mine cooling applications were considered and it was concluded that while this concept would not be feasible as a mine-wide cooling source, there could be specialised applications where it would be beneficial. One application would be to cool backfill and thereby reduce the heat load at the working face. In this case the best performance would be achieved by using the ejector in combination with an energy recovery system such as a Pelton turbine or a three-chamber pipe feeder.

Jan 1, 2005

By D Wallace, H Guo, B Shen

Appropriate management of the ground subsidence induced by coal mining activities is essential. To assess the effectiveness of grout injection for mining subsidence control, time-lapse ground penetrating radar (GPR) imaging data were collected before and after grouting. The pregouting subsurface responses were interpreted to have changed after grout injection. The changes were caused by injecting the grout materials (flyash and water) into the delaminated strata and permeable fracture zones. The largest distance of the observed GPR event changes at the right end of the main profile is 132 m away from the injection borehole. Although the GPR images could not easily tell if the image changes were caused by the injected ashes or the water, it does suggest that the injection materials had been pushed at least 130 m away from the injection borehole. This is consistent with the borehole scan monitoring, which confirmed that the grout has travelled more than 90 m from the injection borehole.

Jan 1, 2006

By R Buerger, D Barrett, P Hodkiewicz

The Emily Ann nickel mine is owned and operated by LionOre Mining International Ltd. The deposit was discovered during 1997 and is blind, concealed beneath 25 m of transported cover and a further 100 m of unmineralised Archaean felsic rocks. Nickel sulfide mineralisation is hosted predominantly in strongly deformed, altered and metamorphosed Archaean komatiitic ultramafic rocks. Subordinate felsic-hosted, remobilised mineralisation is also present. Mining of ore commenced during late-2001. Since the early days of exploration drilling, through feasibility delineation drilling and subsequent mining, a geological model involving thrusting and folding of a komatiitic-hosted nickel sulfide deposit has been an evolving theme. Development of appropriate mine geology procedures, including detailed mapping, significantly increased the confidence of mine-site geology and engineering staff in the geological model and improved operational efficiencies during start-up. This also allowed the engineering and mining team to develop a tolerance for the large fluctuations in daily production grade, with an understanding that budgeted production targets, on a level-by-level basis, were achievable. This paper describes the development of the current interpretation of the deposit and emphasises the importance of a sound understanding of deposit geology. The direct benefits at Emily Ann included improvements in drill targeting, resource estimation and mine planning.

Jan 1, 2003

By B Bendtsen, L McQueen

The use of shotcrete as an efficient means of both temporary and permanent ground support has continued to grow over the last 30 years, with its use underground now commonplace around the world. However, the development of analytical design methods has lagged advances in material and application technologies. Historically, part of the reason for this was a lack of understanding of how shotcrete linings actually worked. Considerable progress has been made in this area in recent years and this paper attempts to summarise the current state of practice with respect to shotcrete lining design. It then concludes by summarising areas where the authors consider future research and development is still required.

Jan 1, 2008

By Jacobs M

After a methane explosion in a coal mine a pre-determined crisis management procedure is instigated. As the process rapidly evolves the inevitable question arises - are personnel trapped underground, are they alive and can they be rescued without putting the lives of the rescue crew at risk? This is a very emotive question with many sub-questions such as; could anybody have survived, is there the potential for a secondary explosion and is there a `window of opportunity' before that secondary explosion occurs?To determine if that window of opportunity exists two fundamental elements must be in place; a method of determining the atmosphere at key points in the mine and a method of predicting the course of change of that atmosphere with respect to time. The first element can be achieved if the tube bundle system is intact and drawing samples from known points, alternatively boreholes can be drilled from the surface. The second element can be realised by utilising a sequence of computer generated control charts which have a time axis, a percentage combustibles axis, the upper and lower explosive limits of the current atmosphere and a prediction option which allows the user to look at the potential changes in the atmosphere over a set period of time. These control charts would be part of the mines on-going crisis management system rather than a tool to be used after an explosion had occurred.

Jan 1, 1998

By M Ujihira, M Komazaki, K Higuchi, D F

A diesel engine with a misfiring cylinder is likely to break down in a short time when the engine is used without maintenance. The authors have developed a method of detecting the occurrence of cylinder misfiring and specifying the misfiring cylinder by using wavelet analysis and statistical analysis on the root mean square (r.m.s.) values of two kinds of acceleration waveforms. This detection method is considered superior to traditional methods, which require several accelerometers, especially in terms of simplicity. Since the development of the method, research has been conducted on semi-automatic processing of measured signals and signal transmission from the worksite to a remote office. Field tests confirmed that 1 + 105 points of dynamic data could be transmitted through the mobile multimedia network within 15 minutes, and the time for signal processing was within 15 minutes. Final determination on the condition of a diesel engine in heavy machinery could be achieved within 30 minutes. Shortened processing time is expected by improvement of the processing software.

Jan 1, 2003

By Moxon NT, Torrace AC

The detonation pressure of an explosive is a function of its density and its velocity of detonation (VOD) and relates directly to the degree and manner in which the explosive loads the surrounding rock. The suitabil- ity of an explosive to any particular situation is determined not so much by the total energy released but more by the rate at which it is released. As the science of rock blasting advances it is becoming economically more important to quantify explosive performance, particularly with respect to quality control and fragmentation. As part of a major explosive user, BHP Central Research Laboratories have developed a number of tech- niques to determine the detonation characteristics of explosives. These include a method of continuous velocity of detonation measurement based on the SLIFER principle. This not only enables the VOD of the explo- sive to be determined, but also has the versatility to allow factors such as under priming, slow run up, the effect of water, variable energy load- ing and the velocity of the shock wave in the stemming to be assessed. Multi point VOD systems have also been developed for more routine appli- cations. With a minor modification they can be used to determine the absolute delay of detonators accurately and economically. Direct deto- nation pressure measurement methods have also been developed based on piezoresistive techniques. Future developments include the incorpo- ration of all the above techniques into a single, portable package, allow- ing easy use on the mine site.

Jan 1, 1988

By Moorrees C

Tests show how that temperature and rate of sparging to remove carbon dioxide determine the rate of precipitation and the chemical and physical properties of hydrated magnesium carbonates precipitated from clarified magnesium bicarbonate liquors derived from crude magnesia. At temperatures above 55°C the product is largely in the form ofhydromagnesite, Mg5(C03)4(OH)2.4H2O Between I5°C and 55°C the major product is nesquehonite, MgCO3·3H2O, although partial hydromagnesite precipitation can be induced by a high rate of aeration.As a result of the reduced time required to bring about greater than 95 per cent magnesium precipitation, the higher MgO content of the product, the ease of product recovery from the precipitation vessel, and the lower energy requirement for thermal decomposition of the precipitate to magnesia, it is preferable to precipitate hydromagnesite rather than nesquehonite. Moreover, the magnesia produced from hydromagnesite is somewhat more reactive than that formed from nesquehonite.Using precipitate calcination temperatures less than 1000°C, the chemical reactivities of the magnesias formed from both precipitates are greater than those of the crude magnesias derived from Savage River magnesite itself. The magnesias would be suitable for most uses developed for caustic-calcined magnesia. However, for refractory brick manufacture, it would be necessary to briquelle the caustic-calcined magnesia. adjust the CaO and SiO2 contents and sinter at temperatures in excess of 1600°C. This would bring about an increase in the bulk density and induce the appropriate chemical bonding reactions.Dead-burned magnesia produced from Savage River magnesite by the calcination/carbon dioxide route would have very low B2O3 contents, typically less than 0.0001 per cent.

Jan 1, 1985

By M Dorricott

This paper describes the design, construction and performance of sill pillars using cemented development mullock at the Crusader Gold Mine. The orebody is some 35 m - 60 m in length, 5 m - 8 m wide, dipping at 60¦ - 85¦ and plunging at about 40¦ to the north. It is accessed via a footwall decline. The ore occurs at the contact between basalt and ultramafic. This contact is characterised by shearing and alteration; and is prone to unraveling failure. The cut and fill mining method at Crusader extracts 25 m high ore blocks in four flat back lifts and one 8 m thick crown pillar. To enable full recovery of these high-grade crown pillars with minimal dilution, a 5 m thick sill pillar is constructed using cemented rock fill (CRF), after mining of the bottom two lifts in each block. Uncemented development mullock is used as rock fill (RF) for subsequent lifts. Development mullock and cement/water slurry is mixed underground to produce CRF. The fill is transported to the stope in LHDs and dumped on the floor. The sill pillar is advanced progressively, with compaction provided by the loader driving over the previously placed fill. Old jumbo rods are installed as shear pins along the flat dipping hangingwall to reduce the risk of rotational failure of the pillar. A fan of cable bolts is installed into the hangingwall to prevent unraveling failure in the sheared ground. Buffer blasting is used to minimise damage to the CRF sill pillar when the crown pillar below is extracted. At the time of writing, extraction of the crown pillar underneath the CRF has taken place at the 930 stope. The crown pillar was extracted successfully with dilution from the backfill and hangingwall minimised and 98 per cent of the gold recovered. This compares with pillars that were mined beneath uncemented backfill where only 70 per cent of the gold was recovered and where there was significant dilution from the backfill and from hangingwall failures. Where no CRF was placed, there were also numerous production delays caused by large rocks from the hangingwall blocking the stope brow.

Jan 1, 2002

This paper reviews an analytical model that defines the relationship of weight-weighted or volume-weighted average haulage distance with bench height and other related parameters; presents the optimum bench heights under various conditions in terms of minimising the weighted average haulage distance of ore/waste during the full lifetime of an open pit mine, and discusses the truck-haulage economics of mining open pits by high bench, specifically by 15 m, 18 m and 20 m bench through marginal analysis. The observations from these analyses disprove the previous conflicting assertions that the overall weighted average haulage distance either increases or decreases monotonically with bench height. It is concluded that: (i) an increase of bench height to 15 m from 12 m is likely to be viable under the general conditions of large-scale deep open-pit mines; (ii) the reduction of haulage cost is limited with the case of increasing bench height to 18 m from 15 m; and (iii) the feasibility of mining open pits by 20 m benches is generally questionable. These conclusions may serve as a useful guide for those who advocate open pit mining by high benches.

Jan 1, 1995

By D La Rosa, W Valery, A Jankovic, S Ese

Metso Minerals Process Technology Asia-Pacific (MMPT-AP) has been working with many mining companies worldwide performing æMine to MillÆ or Process Integration and Optimisation (PIO) studies. MMPT-AP has developed a proven methodology to improve the efficiency of the mine-mill interface and gain maximum benefit. The PIO methodology involves rock characterisation, mathematical modelling and simulation to generate a list of operational and control changes for both the mine and concentrator. Following the methodology, the list of recommendations is developed relatively easily; the more challenging part depends on the company. Success of a PIO project relies on the ability of an organisation to implement change û both operationally and culturally: the human element. When a PIO project is started, there is initial interest and commitment from the company. But how can this be maintained? How does an operation know if the benefit continues? MMPT-AP is now developing long-term relationships with clients to ensure that the increased production and improved efficiency continues. Direct and indirect measurements are used to determine the key factors involved and to understand the cause/effect relationships. Simulation tools also can be used to compare current with recommended practices û so when material properties vary over time, the benefits can still be quantified. PIO is about empowerment: by measuring and understanding what parameters affect concentrator performance, the site personnel now have the knowledge to make a difference. Rather than simply reporting variable or poor concentrator performance, operations can predict when production will be affected and put controls in place to prevent it from happening. This requires support and commitment from the company or æbuy inÆ. Ensuring this buy in continues is the challenge facing every company involved in PIO work û but the benefits are well worth it. This paper will review MMPT-APÆs experiences in implementing PIO projects in the long term: from both the consulting and operational viewpoints. MMPT-APÆs involvement with a number of companies will be discussed as examples of what works and what does not.

Jan 1, 2007

By A Garg

Squeezing can occur both in hard rock and in jointed rock mass as a result of over stressing. It is related to time dependent shearing, ie shear creep and is associated with the volumetric expansion (dilation) and radial inward displacement of the tunnel surface. While planning a tunnel in hard rock under a high cover of the order of 2 km it is desirable to identify the potential squeezing ground conditions and to select appropriate excavation technique and the support measures. There are several solutions to counter balance the squeezing ground viz over excavation of tunnel profile, assessing appropriate excavation technique, provision of a ductile primary support and time for providing tunnel lining. Low drivage rates and high cost due to support failures requiring rectification arising out of poor anticipation of tunnel closures and support pressures are major problems associated with tunnelling under squeezing ground conditions. Under squeezing ground conditions, the deformation will be gradual, therefore, in order to absorb deformations yielding supports are quite useful as primary support which provide a reliable low initial support pressure and permit uniform stress relief of the surrounding rock along with preventing rock from ravelling. The paper discusses the various factors which influence the selection of appropriate excavation technique and support measures in hard rock under squeezing ground conditions.

Jan 1, 1999

The paper explains the genesis of the Ballarat College of Advanced Education to its unique position in mining engineering education. A description follows of the development of the Graduate Diploma in Occupational Hazard Management which commenced in 1979 in the cooperative mode of four groups of three weeks full- time study followed by twenty-three weeks in industry. In particular an analysis will be given of the state of origin of students, ages and employing industries. Given the experience from the evolution of this course a similar process is described for the Graduate Diploma in Mining which has been accredited to commence early in 1987.

Jan 1, 1986

By R K. Dayal

Many transport tunnels show distress after few decades of construction. Owing to exorbitant cost of replacement, rehabilitation of tunnels has become inevitable and rapidly gaining attention/significance worldwide. This paper discusses the detailed planning and design of remedial measures for repairs and rehabilitation of the twin tube highway tunnel in India, at an elevation of 2200 m constructed approximately 38 years ago. The tunnel length is 2547 m having 30 m2 cross-sectional area of each tube. The tunnel is lined in stretches, totalling 60 per cent lined and the remaining portions are unlined. The tunnel has developed acute problems of rock falls, water leakage, distressed pavement and icicle formation resulting in slow movement of vehicular traffic which has also increased. Suffocation inside the tunnel caused deaths due to inadequate natural ventilation, hence artificial ventilation was deemed necessary and was provided in the restricted 28.5 m2 cross-sectional area of tunnel. The paper would be useful for planners, designers and construction engineers for setting future trends.

Jan 1, 1999

By Skinner J, Brackenbury K

The AuPlus" Systems have been applied in the gold mining industry to achieve improved gold recoveries, faster leach kinetics and reduced cyanide consumptions. Calcium or hydrogen peroxide, collectively known as peroxygens, can be used. The choice depending on plant design and the nature of the ore. Laboratory test work and plant trials are included in this paper to illustrate the benefits of peroxygen usage in extractive gold metal- lurgy.

Jan 1, 1991

By R Brake

The Enterprise Mine Project (EMP) is being developed by Mount IsaMines Limited as the future source of copper ore at the Mt Isa miningand processing complex. Environmental engineering is one of the majortechnical challenges facing the project because of the depth of theorebodies, high virgin rock temperatures and hot ambient surfacetemperatures in summer. This paper discusses the engineering principles adopted by EMP to manage the risks associated with working in these adverse thermal conditions.

Jan 1, 1998

By Olden WH

A scheme is presented whereby the complexities of design and operation of a hydraulically powered coalmine support are modelled using the finite element method. This enables predictions to be made of the interaction of the support with its environment in a variety of operating conditions. The model is a two dimensional representation. The modelling scheme was applied in two case studies. In the first, the performance of a four leg support was uprated by increasing the front leg force. The finite element model enabled changes in overall support performance to be verified. In the second case study, the change in lateral force developed by a two leg support was assessed with changes in support operating height and floor foundation stiffness. The modelling scheme is capable of further development with the possibility of extending the model into three dimensions and the addition of control elements that would enable an actual mining sequence to be Represented.

Jan 1, 1992

There was a time, in the memory of some here tonight, when the annual meeting of The Institute was a nostalgic occasion. Often, in the 1920s, there was comment on the decline of Australian mining and on the lack of new mineral discoveries. When some of our Presidents prayed then for a new Bendigo, and instead were given a Mount Isa, they were justifiably disappointed because of the vastly different capital requirements.In 1967 the mining picture is very different. The recent mining developments in Australia are certainly as important as several Bendigos and several Kalgoorlies. The mining industry in Australia has never been more dynamic than today (Table 1). And if we ask why it is so dynamic, the answer lies in the role which overseas capital is playing in the industry. The contribution of overseas capital should concern us not only because we are members of the mining and metallurgical profession, but also because we have a duty to make our profession contribute as much as possible to the well-being of Australians. It is not sufficient to argue that overseas capital is good for the mining industry; we must also examine whether it is good for the economy and the nation. In this context the current criticism of the inflow of overseas capital into Australian mining is useful, for it gives us an opportunity to see what has resulted from the inflow.In discussing this question I do not suggest that we emulate Captain Hancock, that legendary Moonta mine manager who, according to Oswald Pryor's cartoon, used to say to his miners: "When I say a thing is, it is, even if it isn't". The question can only be discussed on a factual basis; and I would submit that many of the important facts relating to overseas capital in our mining industry are often overlooked or ignored. I would further submit, on the basis of these facts, that Australia's present day mining industry has been largely built on overseas capital and that the overall benefits of that capital to Australia have been enormous.

Jan 1, 1967

This paper reviews the use of MTU diesel engines in uses such as Off-Highway Vehicles, Rail traction, Generating Sets, Marine Propulsion and Defence Applications, and focuses on a central theme of maximum power in the minimum of space.

Jan 1, 1986

By Soldenhoff K, Levins D, Collier D, Day A, Secomb R, Brown S, Tapsell G, Bellingham A, Quan C

Bench and pilot plant studies were carried out at ANSTO to develop a process for rare earth recovery from the Mt Weld deposit near Laverton, Western Australia. This paper describes the development of the flowsheet, which is similar to conventional monazite processing, but with the introduction of several innovative steps to account for the complex rare earth mineralisation and the presence of specific gangue minerals. A unique feature of the flowsheet is the recovery of cerium by solvent extraction from a sulphate leach liquor. The process was tested continuously by the operation of a pilot plant at ANSTO's Lucas Heights Research Laboratories, Sydney in the first half of 1992. The plant, designed to treat 100 kg per day of beneficiated ore, confirmed the viability of the process, with rare earth products from the operation satisfying stringent buyer specifications.

Jan 1, 1993