Search Documents

Mining is taking place at increasing depths of cover on the Southern Coalfield beneath pre- dominantly massive sandstone strata. Within the next twenty years, there will be longwall mining at depths greater than 600 m. As the Sydney Metropolitan area continues to expand and as coal mining approaches these urban areas subsidence will continue to become an increas- ingly important aspect of coal mining research. Investigations commenced in the mid 1960's and it is now possible to predict subsidence in the Southern Coalfield with reasonable con- fidence. The work is showing that the characteristics of the subsidence troughs over the deeper mining at Appin differ from the characteristics of mine subsidence at less cover. The longwall mining at Appin Colliery has resulted in a maximum measured subsidence of 730 mm. The maximum strains were small because of the large radii of curvature of the subsidence profiles. There was no damage to any of the buildings in the township of Appin.

Jan 1, 1981

That gold will dissolve in sodium hyposlphite solutions is known from the lixiviation of silver and gold ores.The gold will dissolve only in small quantities. According to Stetefeldt, if gold leaf is treated for a time with sodium hyposlllphite solutions of varying strengths solution takes place in every instance, the deviation in quantity being very slight.In order to form hyposulphite double-salts, the gold must become oxidised, the oxygen being derived from the air absorbed by the solution. Consequently, it is the quantity of free oxygen in the solution by, which the reaction is determined, as for one equivalent of gold dissolved one equivalent of caustic soda is set free.

Jan 1, 1901

By Brechtel C. E

Providing adequate airflow to effectively dilute and remove diesel pollutants in large mine working headings is a little researched area. A simulated diesel mucking operation was carried out in the Exxon Colony Pilot Mine in Colorado to establish expected levels of diesel pollutants in dead-ended working headings. This heading was nominally 15.3 m (50-ft) wide by 9.2 m (30-ft) high. Two face ventilation systems were tested using sulfur hexafluoride tracer gas to represent the diesel pollutants. The results of these tests showed that conventional face ventilation systems operating at high flow rates could adequately ventilate diesel equipment in the 447-522 kW (600-700 hp) range, even in a dead heading 91.4 m (300 ft) in length.

Jan 1, 1988

By Harbort G. J

Jameson cell pilot plant trials were conducted in a number of areas in the Red Dome gold/copper flotation plant during 1991. The aim of testwork was to reduce the amount of cyanide soluble copper reporting in tailing to the gold leach plant, and hence reduce cyanide consumption. A number of these tests were conducted in parallel with conventional flotation columns. Laboratory tests were conducted to simulate the performance of the existing plant when compared with the addition of the Jameson cell allowing an extra sulphidising phase. This paper reviews the comparison of the Jameson cell and conventional columns in recovering cyanide soluble copper, while maximising copper concentrate grade. Key parameters that are investigated are residence times, air/pulp ratios, superficial gas recoveries and size by size recoveries. A brief comparison of performance of the Jameson cell and column in the controlled potential sulphidisation process is also presented. An estimation of the reduction in cyanide consumption is given.

Jan 1, 1992

By Adranyl W. W

Sub-level caving with bottom ore drawing has gained wide acceptance in rich, soft, low magnetic iron ores because it provides moderate ore dilution and ore losses. The main problem here is the high rock pressure exerted on sub-level drives situated in the sub-level sill pillars. To reduce this effect, the ore block is divided into panels. This paper illustraes the method of determining the maximum panel width providing low maintenance cost of sub-level drives.

Jan 1, 1995

Uniaxial compressive strength and Young's modulus values measured in the laboratory on NX diamond drill cores were examined statistically to bring out any significant differences between different locations in the mine which might require special treatment in subsequent photoelastic analyses of the mine layout. Correlations were sought between the strength and modulus and various other features of the rock. The estimated mineral content of the core correlated with the modulus of the core, but the range of modulus values was too limited to show any strong correlation with compressive strength.Strength in the vertical direction was found to be significantly higher than in the horizontal direction and the same pattern was followed by the moduli, but was less pronounced. It was concluded that, whilst the modulus variations were significant, they would not invalidate any photoelastic studies.

Jan 1, 1969

In-stope long hole drilling (face parallel drilling) is a new technology currently being applied to shallow dipping (

Jan 1, 2003

By J Koppe, J F. Costa

A fundamental error of sampling occurs when a sample is extracted from a larger mass of ore or lot. The act of sampling requires that all particles belonging to the lot have an equal chance of being extracted. This type of sampling is called unbiased sampling. The sampling equipment (herein referred to as the sampler) should be constructed with some additional mechanical characteristics to guarantee that the samples will be unbiased. Samplers, extracting increments from a continuous flow, such as a conveyor belt, collect aliquots at regular time intervals. These time intervals relate to the number of aliquots extracted from a given mass of lot, whilst passing through the continuous flow. The frequency of extractions will influence the precision or the error of the sample (integration error). Further, the ore variability influences the amount collected from the continuous flow. Normally, the sampling protocol utilised is designed for the extractions obtained from the conveyor belt, omitting any error committed during this operation, ie the error of extracting from the continuous flow. This study aims to analyse the error of sampling a continuous flow by using a variogram with added on auxiliary functions. Each different piece of material passing through the flow will exhibit a distinct temporal variogram, which should influence the frequency of the samples being extracted for each chosen sampling error. The methodology used is presented in the form of a case study from a coal processing plant.

Jan 1, 2005

Several years and millions of dollars later, the mining and extractive industries have now started to receive and implement industry based standards aimed at achieving better performance and output from the employee. IFAP in conjunction with the mining and quarrying industry has developed a range of training courses aimed at achieving the benefits that can be gleaned from application of these standards. The establishment of a career path and appropriate training packages for personnel involved in the handling and use of explosives provides industry with a training system that previously did not exist. The opportunity to receive quality training based on industry standards and aimed at achieving industry goals will now enable the industry to optimise itÆs explosives applications.

Jan 1, 1999

By O K. Paki

A 14/12 millMAXTM pump was installed in the SAG1 grinding circuit as a trial replacement for the existing 12/10 Warman for performance comparison and in an attempt to overcome process difficulties. Krebs Engineers have developed the millMAXTM pump wet end to adapt to a variety of power frames. This system has been developed specifically for coarse material contained in mill discharge. SAG1 discharge screen undersize with a top size of 10 mm is collected in a flat bottom sump. Two 12/10 Warman pumps located on the same side of the sump, pump the screen undersize at 50 to 65 per cent solids to a distributor box which splits into two separate ball mill circuit sumps. One pump is installed towards the screen feed, while the other is towards the screen oversize discharge. The pump located towards the screen oversize discharge is prone to continual operating problems including pump bogging, high impeller and casing wear, and has consequently restricted SAG mill throughput. To rectify this pumping problem, it was decided to change-out the wet end of this pump with a millMAXTM. The design of the new pump enabled the wet end only to be retrofitted to the existing Warman pump frame, thus reducing change-over time. This was undertaken in the workshop under the supervision of a company representative where the pump, complete with bearing frame, new wet end, motor and base frame, was assembled. After installation of the millMAXTM pump during a SAG mill shutdown, performance indicators including motor power draw, sump level, and pump discharge pressure have been monitored. The trends indicate an increase in discharge pressure, low sump level, and low motor power draw. With the improved pumping efficiency there has been minimal pump bogging and no consequent SAG mill throughput restrictions. Pump wear rate has also decreased.

Jan 1, 2000

By P Lilly

Blasting is the primary comminution process in most mining operations. This process involves the highly complex and dynamic interaction between two main components. The first is the detonating explosive and the second is the rock mass into which the explosive is loaded. The mechanical properties of the rock material (such as dynamic strength, tensile strength, dynamic modulus and fracture toughness) are important considerations in understanding the blasting process. However, it is the characteristics of the geological defects (joints, foliation planes, bedding planes) within the rock mass that ultimately determine how effectively a blast performs in terms of fragmentation, all else being equal. The defect characteristics include, but are not limited to, their orientation, spacing, and mechanical properties. During the blasting process, some of the geotechnical characteristics of the rock mass are substantially changed. From the blasting outcome point of view, the most notable and important is the change in fragment size distribution that the rock mass undergoes. The pre-blast in situ defect-bounded block size distribution is transformed into the post-blast muckpile fragment size distribution. Consequently, it is fundamental to our understanding of and ability to predict the blasting process that both the blastability of a rock mass and its transformation into the fragment size distribution can be appropriately quantified.

Jan 1, 2001

By D L. Kennedy

It has always been a challenge to accelerate the underground development progress by increasing the advance rate of each development round. Surveys have shown that most of the development rounds have only been pulled 84 per cent to 94 per cent of the drilled length. Where bare detonators have been used as primers, less advance rate is expected. In order to obtain a good understanding of the influence of priming upon the advance rate in underground development, a series of high energy primer trials has been conducted by Orica Explosives in the goldfields using various types of Orica high energy Anzomex « primers. It has been shown that development face has been pulled an extra 140 mm to 420 mm by priming with Anzomex « K primers compared with conventional primers. From all the trials at different sites, we have seen that the face pulled using K primers was more square than that pulled using conventional primers. Virtually, no butts and toe were left on the face developed using K primers. Computer simulation has been conducted using either a conventional primer, a bare detonator or a K primer as initiator. The study compared the predicted crack patterns developed around the toe of the hole and it was deducted that a detonator-initiated hole would leave a butt some 200 mm longer than that from a conventional primer-initiated hole, and a K primer-initiated blasthole would give rise to stronger initial p-wave, promoting crack development around the toe and increasing the ability to pull close to the full depth.

Jan 1, 1999

By M Hedley

Tracking plant and personnel in underground environments provides multiple potential benefits for a mine including increasing safety, better monitoring of production, traffic control, and in the future monitoring and control of autonomous vehicles. The main techniques for wireless tracking are to use radio frequency identification (RFID), signal strength based techniques, and time of arrival (TOA) based techniques. RFID does not provide continuous tracking and signal strength techniques have poor accuracy in the complex radio propagation environment present in mines. TOA based techniques are potentially the most accurate, but most current equipment does not realise the potential of the technique. CSIRO has been developing the wireless ad-hoc system for positioning (WASP) system for wireless tracking in a range of challenging environments including underground mines. WASP has been licensed for sporting applications and has delivered encouraging results in early trials for a surface and an underground mining application. The system utilises a number of ‘anchor nodes’ that are placed at surveyed fixed locations within the mine, and tags attached to plant or personnel to be tracked. The system provides an ad hoc data communication network, thus wired data connections are not required to the anchor nodes. WASP uses transmissions in the 5.8 GHz ISM (instrumentation, scientific and medical) frequency spectrum to perform highly accurate ranging between nodes, hence tracking of tags. The localisation performance of the system depends upon the radio propagation environment, ranging from 0.1 m in low multipath conditions. In this paper we describe the WASP system and provide results of initial testing in an underground mine that shows that the system achieves high ranging accuracy, hence localisation accuracy.

Mar 21, 2011

AustraliaÆs success as a mineral producer and exporter rests heavily on its technological competence. That competence is based not just on adopting internationally-developed technology but also on ground breaking research conducted at Australian research institutions, many of which have global reputations. A number of forces are now operating to speed the introduction of advanced technology to mining and processing operations around the globe and this will create pressure on the Australian industryÆs ability to retain its competitive edge. Examining the foundations of that national research base and the associated culture of innovation may provide some guide to the dynamics that will be required to maintain technical competitiveness in the future.

Jan 1, 2008

By Chen J, Sun ZY

The present paper gives the design of a new HGMS for magnetic separation of sulphides. The main characteristics of this HGMS are using iron-cladding saddle-shaped magnetic coil for instead of the ordinary magnet, and combining reciprocal-linear motion with vibration to actuate the separation box, and the magnetic field intensity is high up to 2T as well. For improving the magnet system design, a modified finite element method is used to calculate the distribution of magnetic field intensity of separation space of the magnetic coil, and accordingly the calculation results the magnetic leakage coefficient can be determined easily, thus designers apart from the empirical way. KEYWORDS: HGMS, reciprocal motion and vibration, finte element method, saddle-shaped coil.

Jan 1, 1993

By Cecala AB

For 20 years the US Bureau of Mines has been researching strategies for improving the physical, social, and psychological work environment of the miner. The products of this program have shown that a consistent link exists between safety and productivity, and the key to this link is the use of effective human factors and management practices. There are specific research findings from the research projects of the Bureau on ergonomic design of mining equipment, redesign of tasks (especially materials handling) to minimize back injuries, human resource management techniques for increasing safety and productivity, and improved shift rotation schedules. Current research is continuing these themes with new applications to high technology mining systems, including computer assisted extraction devices and mine monitoring.

Jan 1, 1991

By N Vagias, R Shaw, M Coghill, W Easman

Rio Tinto Technology and the Rio Tinto Foundation for a Sustainable Minerals Industry have funded the development of a practical floating module that can reduce water losses through evaporation from water dams at mining and mineral processing facilities by about 75 per cent. The modules, which are also suitable for use by farmers and communities, were designed for easy deployment, to allow the water to æbreatheÆ, harvest rainfall and resist wind speeds of more than 100 km/h. A large-scale demonstration trial will be conducted at the Northparkes Mine, located near Parkes (New South Wales, Australia). The objective of the trial is to demonstrate to Rio Tinto business units, community, farming and government groups the moduleÆs operating costs and water saving potential.

Jan 1, 2006

Key incompatible element ratios for metabasalts from the Early Permian Croisilles and Patuki Volcanics, South Island, New Zealand, provide constraints on the tectonic environment in which their precursor ophiolitic protolith formed. Two geochemically distinct metabasalt suites are recognised among both the Croisilles and Patuki rocks. Metabasalts from one suite exhibit the geochemical signatures of depleted tholeiites from oceanic spreading ridges (N-type MORB) or spreading centres in evolved back-arc basins. These N-type tholeiites show high Zr/Nb ratios (Zr/Nb = 37-62) and are depleted in light rare earth elements (LREE)((La/Y)N

Jan 1, 1987

I feel a little like the Parson delivering his Sunday Sermon, chastizing his parishioners for not coming to Church. Those who need to hear me are absent.Nevertheless, I hope that if you agree with what I am about to say you will go forth and spread the word.We often hear of the impact mining has on the community. I prefer tonight to deal with the impact some community attitudes have on mining, and I want to point out that the results of these attitudes rebound to the detriment of our society. I want to deal particularly with regulation, taxation, and proflts.In a civilization whose standard of living is essentially dependent on an adequate and reliable supply of cheap metals and fuels, it should be evident to Blind Freddie that mining must be encouraged.I must express concern at the constraints inflicted on the mining industry by our community. We tend to blame Government for our difficulties, but we must recognize that Government acts merely as agent for the community. It is fair to say that in a free society, if Government actions do not reflect the demands of the electorate, then it doesn't stay the Government. It is important though for Government, in framing its policies, to ensure that it is not unduly influenced by the loud voices of minority groups.The people of our nation have every right to demand that our industry meet certain criteria to be allowed to operate. We all wish to live in a healthy and congenial environment, and to have our individual comforts protected. It is essential, however, that the community realizes that its demands on the mining industry are affecting Australia's prosperity.Each new regulation and each new tax or impost has its effect on investment, employment, and national revenue. Restraints result in an increase in costs which in turn raises the minimum value of a mineral deposit which is economically mineable. It results in minerals, which could be mined under more favourable circumstances, remaining in the ground, perhaps lost for ever.

Jan 1, 1978

By Lightfoot BW, Wand PD, Towne DV

Sampling and e.m.f. probes were used in the liquid flow from the blast furnace and in the forehearth to evaluate the performance of the copper smelting system at E.R. & S. Significant variations in temperature, oxygen potential and copper content with slag depth and with position in the forehearth indicated that convective currents were causing considerable stirring in the forehearth. This was attributed to temperature fluctuations in the stream from the blast furnace, which resulted in colder slag being underlain by hotter matte. Tracer tests in the feed to the smelter and in the feed to the forehearth revealed considerable holdup of material in the plant and confirmed that the forehearth involved small scale turbulence but little large scale mixing. The results indicated that the copper content of slag continuously tapped from the forehearth could be lowered by at least 0.15% if better settling could be achieved and means of attaining this are discussed. As part of the investigation the recovery of copper from spent refractory bricks recycled through the smelter was evaluated. It was found that the recovery was high but it seems likely that the brick material is partly responsible for a build up of solid material in the forehearth.

Jan 1, 1981