Search Documents

By M Zoorabadi

Overcoring is a common technique to measure in situ rock stress using the concept of stress relief. The strains measured during overcoring are used to calculate the stress tensor assuming continuous, homogeneous, isotropic and linear elastic behaviour. This approach does not recognise any effect of the thickness of the rock annulus produced during overcoring instead assuming that the stresses are entirely a function of the difference in strain between the start of the overcoring and the end with no regard to the transient strains produced. Three-dimensional numerical modelling was used to simulate the overcoring process and investigate the impact of core diameter on the transient stresses and strains during overcoring. This study showed that in thicker core, maximum transient axial stresses and strains occur when the drill bit approaches the measuring point and greater tensile axial stresses were produced when the annulus was thinner. CITATION:Zoorabadi, M, 2018. Numerical study of annulus thickness on overcoring stress measurements, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 274–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M A. Tuck

Air blasts or wind blasts as they are termed in underground coal mining, occur in a number of types of underground mining where a void develops and the overlying or adjacent rock fails rapidly to allow the development of a high pressure air pulse. The effects of air blast vary widely from very low consequence to high consequence events causing multiple fatalities as occurred at North Parkes mine. The aim of this paper is to examine the phenomena of air blasts and the underlying parameters which determine the severity of the air blast event. A basic model under development is then detailed. The aim of the model is to determine the magnitude of the pressure pulse(s) developed during an air blast event. This, combined with a transient ventilation network analysis model will enable the airflows and associated pressure drops to be determined and allow the pressure pulse around the mine to be evaluated. The overall aim is to allow mining engineers and mine ventilation engineers to undertake a risk assessment of air blasts at individual mine sites, allowing working parameters to be changed to eliminate or reduce air blasts, or engineering controls to be developed to reduce the effects of air blasts.CITATION:Tuck, M A, 2013. Determining the pressure pulse for an air blast, in Proceedings The Australian Mine Ventilation Conference , pp 103-106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The approach to this subject is a very general one, but an attempt has been made to cover briefly a very wide field in the nationally important job of manufacturing iron for the iron and steel industry.Some historical data concerning the development of the furnace itself from early days have been followed by the modern ideas on raw materials and their beneficiation. Recent furnace design and modern auxiliaries have been given attention with, finally, some developments in practical operation.HISTORICALWhen dealing with such large 'and costly operating units as blast furnaces, there is not the same opportunity for research in design as in most other metallurgical processes. Over past generations the development of furnace design, or "lines" as it is usually termed, as well as most radical operating changes, has been very gradual.However, there have been some periods of rapid progress due to revolutionary changes. One such was the adoption of the steam engine for blowing and charging operations, and also, during this same era, about 1750, coke was first used as fuel in place of charcoal. Another revolutionary change came some 100 years later, when heating the blast became usual practice.Since then there have been great improvements in mechanical equipment and in the preparation of raw .materials. These factors, together with a better understanding of what happens inside the furnace, have led to the development of those large mechanically operated structures which are the most modern in blast furnace design.For many, years America has led the world in pig iron production and in furnace development, so that American design and practice is now recognised almost as standard. This type of furnace replaced the older stacks in England, Russia, Germany, South Africa and India, as well as here in Australia.

Jan 1, 1947

By M Hassall, E Humphries

Personal risk assessment processes, also known as Take 5 or SLAM (Stop, Look, Assess, Manage) have been utilised in high hazard industries for over 30 years. However, there is limited research to understand if a personal risk assessment process improves safety and health outcomes. The author’s learnings during discussions with training participants in G3/G-MIRM (Risk Management Systems) and G2 (Risk Assessment for Supervisors) courses have provided them with significant insight into understanding if a personal risk assessment process is valued across a number of mining industry organisations. These discussions arise when the four-layer model is presented (Figure 1) where ‘Layer 4’ represents the last resort risk checking activity. In this context, training participants agree that this process has value. However, the consistent opinion is that the personal risk assessment process is not effective, that it is a ‘tick and flick exercise’ and is not achieving the desired outcomes.

Apr 16, 2024

By McCarthy P. L

A distinctive feature of the goldfields of Victoria was the extrac- tion of gold from deep leads, that is the buried river beds of Vic- toria's ancient rivers and streams. It is estimated that about 265,000 kg of gold was produced from Victoria's deep lead mines which comprises about 11.5% of Victoria's total production of gold (Bowen, 1974). The significance of deep lead mining for Victoria, however, went far beyond its economic contribution to Victoria. If Profes- sor Blainey is correct it was the frustrations of mining gold from deep alluvial leads in Ballarat during 1854 which precipitated the Eureka Stockade (Blainey, 1963, 46-52). This event resulted in the implementation of a fair mining administration and was an emphatic statement of the rise of democratic movements in Australia. Much of the technology and skill for mining deep leads had to be developed locally because at that time no other major gold- field elsewhere in Australia or the world had gold deposits with comparable problems. Deep lead mining in Victoria was there- fore largely a home grown industry and the equipment for that industry was often designed and produced in Victoria.

Jan 1, 1988

By K C. Corin, N Ndamase, M Tadie

Mining operations in arid regions are compelled to reduce their consumption of fresh water. Closed water circuits are an attractive solution and, in addition to reducing freshwater consumption, have the added benefit of reducing reagent consumption as well as the environmental impact by eliminating effluent discharge. Accumulating ionic species have been shown to hinder collector adsorption which reduces the recovery of valuable minerals. Numerous studies have investigated the effect of degrading water quality on collector adsorption however there is very limited understanding as to how this takes place from an electrochemical perspective. This study therefore aims to investigate how the presence of accumulating ionic species at varying concentrations affects the electrochemical adsorption of sodium ethyl xanthate onto galena. The synthetic plant water used in this study comprised of single salt solutions to isolate the effects of the ionic species of interest. The ionic strengths were varied between 0.0242 M, 0.0727 M, 0.1212 M and 0.2426 M which correspond to University of Cape Town (UCT) Centre for Minerals Research (CMR) synthetic plant waters of 1, 3, 5 and 10SPW, respectively. Mineral rest potentials indicated how changing water quality affected xanthate-mineral interactions. Microflotation observed the impact of changing water quality on mineral floatability.

Aug 24, 2022

By P M. Dight

Shotcrete usage in declines and developments has become pervasive as operators strive to achieve production improvements. Issues of mix control, fibreload, thickness control, temperature and curing conditions all play a part in the quality control. Often to overcome some of the quality control issues designers over specify the strength requirements in order to meet their operational constraints. Adherence to the standard civil testing requirements of 28 days moist cured at 21ºC without properly calibrating these results to the changing environment underground leads to contractual disputes. There are a number of standard tests specified including cylinder tests, cored tests, beam tests and round determinate panel (RDP) panel tests. The logistics of storing these samples and then transporting them to concrete testing laboratories without due regard to temperature changes with time can influence the results. All the samples can be readily handled by personnel except the RDP panel. The standard RDP panel is 800 mm diameter by 75 mm thick and requires an ITH machine at the mine and a fork lift at the laboratory to move it around. This paper will examine the possibility of a panel which provides scalable results to the standard RDP panel but can be easily handled by personnel and/or tested on site with suitable equipment. This allows for faster turn around and better quality control for the sample prior to testing. This enhances the identification of quality control issues at the mine and improves safety.

Mar 21, 2011

By J B Tucker, A T. McGrath

Situated in north-west Queensland, Australia, the Ernest Henry Mine (EHM) has been producing copper and gold since 1996. Owned and operated by Glencore Xstrata, ore is currently sourced from a newly developed underground sublevel cave (SLC) mine below the old EHM open pit (the pit). Ore feed to the concentrator is supplemented by satellite open pits comprising the Mount Margaret operation.The transition from open pit to a producing underground mine involved a complex extraction sequence for the first two production sublevels on RL1650 and RL1625. Underground mining during cave initiation was further complicated when south wall instability prevented completion of the final open pit shell. The transition mining phase included mass firing of an inclined crown pillar between the initial SLC void and the pit followed by a combination of transverse and longitudinal SLC mining.The inclined crown pillar mass firing was the first significant milestone in the extraction of the transition ore block. Comprising approximately 890 000 t of in situ material; 70 000 m of drilling was charged with 351 t of emulsion and 6026 electronic detonators to initiate the single mass firing. The firing contained five direction changes over 19 seconds making it one of the largest and most complex underground blasts ever conducted in Australia.Risk management was integrated into every facet of the technical and operational planning and execution of the transition mining phase, whilst maintaining daily mine construction and production commitments. This paper provides a detailed overview of the transition objectives and constraints, mining method selection, post mass blast outcomes and the journey ahead.CITATION:McGrath, A T, Campbell, A D and Tucker, J B, 2014. Transition of the Ernest Henry Mine from open pit to an underground sublevel cave, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 297–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

Warrego copper ore characteristically contains 0.05-0.2% bismuth, which on upgrading produces a concentrate of approximately 1.3% bismuth. Early smelting of this concentrate (1973) was accomplished in a flash furnace (eliminating 92% of the bismuth in the con- centrate) and Top Blown Rotary Convertors (eliminating 85% of the bismuth in the matte). However 1.3% bismuth was considered the max- imLun bismuth level that could be treated. Geological evidence indicated that the bismuth level in~the copper ore would increase and that the bismuth level in the Warrego ore would be 0.3-0.7% bismuth. Treating these ores would produce a copper concentrate with bismuth levels far in excess of those accept- able to the smelter and still produce low bismuth content blister (limit 0.03% bismuth).

Jan 1, 1984

By Weyer J

Many existing computer planning programs for the mining industry focus either on big mining enterprises with a high production rate or on smaller operations for high value minerals. Big mining enterprises, like the hardcoal company `Ruhrkohle AG' in Germany have their own R&D departments which develop powerful computer programs for planning purposes, partly in co-operation with mining universities. However, there is a remarkable number of small- scale mining operations which are either not able to buy expensive hard- and software or don't have the skills for the operation of extensive software programs. Partly there is also a trend in using rule of thumb calculations rather than computer programs which need a lot of - partly unavailable - data. For this reason a computer program was developed which does not need expensive hardware and software and which can help the planning engineer in the selection of a limited number of possibilities. Until this time the planning engineer established two or three different cases and calculated the results with a pocket calculator. This could last some hours or even some days. Now he or she can use the computer program with a normal PC to compare the cases. All activities are menu-driven. The basis for all, calculations are fixed and variable costs as well as average performance for special activities. The paper gives an example for a possible planning situation in fluorspar mining (originally this program was developed for the fluorspar enterprise Lengenfeld in Germany). It shows the initial situation, the main structure of the program, the input logic and the results. Benefits, limits and possible extensions of the program are discussed.

Jan 1, 1995

After a short presentation of the Division of Mining at the Royal Insti- tute of Technology, Stockholm, Sweden, the author presents some of-the fill research carried out at the Division. Literature surveys and testing methods and equipment are described. The use of flocculants' in hydraulic filling has been tested both in laboratory and in mines and the results are very promi- sing. Finally compressibility investi- gations and some finite element calcu- lations are presented.

Jan 1, 1973

By S Bhandari

A model for predicting dust plume dispersion from blasting operations using the Eulerian mathematical algorithm has been developed. This model considers atmospheric stability, and wind velocity and direction for computing dust concentrations at different distances from the blast. Software has been developed which simulates the movement of a dust plume at a given horizontal distance from the blast location and time elapsed after the blast. The concentration of dust is also given in vertical planes. It takes into account ground profile and atmospheric conditions such as temperature, pressure, humidity, wind velocity, wind direction and shear. Experiments were carried out in two limestone mines to calibrate the accuracy of the predictions made by such model. High volume dust samplers were used to collect dust samples. Difficulties encountered in satisfactory dust sampling and quantification of results have been described.

Nov 8, 2011

By Shunli Z, Jin X, Guanzhou Q

Flotation behaviour can be controlled, due to diminishment of granula quality and extension of specific surface area, by adding coarse particles (high- grade concentrates) to condition pulp. It has been substantiated that coarse particles can intensify fine particle flotation and its mechanisms are effects of carrier, intermedium and assistant aggregation of coarse particles. Calculation and analysis of Reynolds numbers and their variation for different size particles, under specific turbulent dynamic conditions, reveal that agglomeration among granulae is subject to specific turbulent dynamic conditions. Furthermore, sizes and adhesion strength of flocculated particles are the function of specific physical and chemical factors. Based on this research an innovative ramification carrier flotation process has been developed, which has been applied to Fankou Lead- Zinc Mine, Guang Dong province, China, etc, with satisfactory results. These results shed light on distinction between conventional flotation and fine particle flotation, meanwhile, provide a basic approach for further solution of fine particle flotation problem.

Jan 1, 1993

Joint ventures exist as a means of sharing risks and obeying regulations. An unincorporated joint venture allows a company to take a share only of a project yet allows that company to treat such share as though it were an integral part of the company. The nature of the risks inherent in many ventures is described and comparisons made with alternative corporate vehicles. Different procedures for managing joint ventures are also reviewed and the types of problem encountered in establishing and operating joint ventures are discussed. The basic characteristics of successful joint ventures, in Australia, are listed and a conclusion reached that, despite its difficulties, the joint venture will continue to proliferate as a corporate vehicle for project development.

Jan 1, 1983

By Mirabediny H, Whitchurch K

A computerised simulation model has been developed to select the most suitable digging method of a dragline operation for a given geological condition. The developed procedure uses a geological ore body model as the basis for the geologic database. The simulation selects the most cost effective dragline digging method from a database of various dragline digging methods The database consists of common and innovative dragline methods currently used in Australian open cut mines. A generalised computer package, DSLX, was extensively used to simulate various dragline digging methods. The DSLX software uses predefined functions to build strip geometry, working benches, blast profiles and spoil piles. The outputs from DSLX in form of volumetric, swing angles and hoist distances data are then aggregated with dragline specifications and site time study data to compare productivity of selected digging methods. The result of a case study showed that this procedure lends itself to the 'optimum' selection a dragline digging method for a given coal deposit.

Jan 1, 1995

The first mining in Western Australia probably commenced some 40 000 years ago when Aborigines arrived and began quarrying stone for tools and weapons, and ochre for decoration. The earliest documented mining by European settlers took place in 1850 on a small lead vein in the bed of the Murchison River, reported by the explorer A C Gregory. However, it was the discovery of gold in the Kimberley region in 1885 that first drew wider attention to the State's mineral potential.

Jan 1, 1992

By H R. C Pratt, G W. Stevens

Hydrodynamic and mass transfer performance are presented for a 72.5 mm diameter pulsed disc and doughnut column of the type used by Western Mining Corporation, Olympic Dam Operation, for the extraction of uranium from sulphate media using Alamine 336 as extractant. For the present purpose, 4.0 g/L sulphuric acid was used as solute. The mass transfer data were interpreted in terms of the diffusion model, thus accounting for continuous phase axial dispersion. The results indicated that an efficiency corresponding to approximately one transfer unit over the 1.0 m height of the column was obtained. This efficiency is comparable to that observed by Gottliebsen (1997) for a pulsed perforated plate column using 173 gm/L sulphuric acid.

Jan 1, 2000

By Stewart W. J

The volumetric method of estimating hydrocarbon resources and recoverable reserves is and probably will remain a dominant method in petroleum engineering. The method is technically very simple, but has one main problem: how to express, measure and properly handle the variable and complex uncertainty of each estimate. The computer age brought in the Monte Carlo Simulation method which enables correct arithmetic operation using data with specified probability distribution. However, several problems are still not solved uniquely and still exist. For instance, the determination and description of the distribution of single parameters, the determination of the degree of dependency between parameters (e.g. hydrocarbon saturation-porosity), and standard probabilist- ic definition of generally used categories (e.g. proved, probable, possible). Methods for handling these problems are discussed.

Jan 1, 1979

Five Hypotheses are given for factors influencing long-run metals price forecasts. 1 . Geologists succeed when given the money. 2. Better understanding of a metals market depresses its price. 3 . Statistical techniques get forecasts wrong. 4. Long-run metals prices are related to crustal abundance. 5 . Economic cycles affect metals prices more than is realised. These are then framed within the transition between eras as influenced by apparent long waves in economic activity. Innovation surges during the transition between eras. The transition to the 5th Wave since the Indus- trial Revolution 200 years ago is now underway. Finally, price projec- tions are given both for the 5th Wave and 200 years from now on the assumption that a similar monetary measure to today will be then extant.

Jan 1, 1988

By M Yahyaei, F Reyes, R Lage, V Jokovic

Equipment wear is strongly related to the performance of grinding circuits. In particular, SAG mills are subjected to the wear of their shell liners and grates. Changes in lifter height and face angle impact mill performance, while classification at the mill discharge is also affected as grates wear out. Moreover, liner mass loss caused by wear affects how operators interpret readings of sensors such as load cells or bearings pressure. Automating and optimising grinding circuits under these constrain becomes challenging due to the nonlinear and dynamic nature of the system. The operation of SAG mill grinding circuits remains largely dependent on human intervention, which frequently results in inconsistencies in performance across shifts, reflecting the operator’s personal preferences, experience, and other human factors. The influence of human factors can be reduced by careful training of operators as well as by automation using advanced supervisory control. The latter approaches could benefit from the development of dynamic process models that consider the effects of wear on the performance of equipment over time. This paper presents detailed industrial data showing the effects of wear on SAG mill performance. Additionally, a dynamic SAG mill model that accounts for these phenomena is proposed and demonstrated in a simulated environment. This model is shown to mimic the effect of wear on the performance of industrial scale mills and the operational constraints they are subject to, thus extending traditional SAG mill models. Incorporating wear into modelling and simulation platforms can improve the understanding of the effects that wear can have on the performance of key assets in comminution circuits and may allow the development of more robust model-based advanced process control strategies.

Aug 24, 2022