Search Documents

By T Connor

Alkali emissions are one of the environmental challenges facing alumina refineries. Queensland Alumina Limited (QAL) is undertaking a number of initiatives to continuously improve its environmental performance. One of these is a program aimed at the reduction of alkali emissions. Alkali emissions originate from a number of sources (eg elevated open tanks), and its level depends on a number of process parameters/ mechanisms (ie splash filling, thermal currents in tanks, streams discharged from a pipe, tank temperatures, atomisation) and climatic conditions (eg wind speed and direction, rain, etc). Under normal operating conditions, there is a continuous low level of alkali emissions from the plant. Certain vessels within the plant have been identified as major contributors to this level of emission, while certain activities within the plant contribute to a temporary elevation (æspikeÆ) of alkali emissions. QAL developed a method using phenolphthalein-treated pads to measure emissions within and outside QAL boundaries. These provide no information about mass emission rates but are important for detecting if alkali material is present. Since mass emission rates are important for determining if improvements in emissions are made, QAL identified the need to design an improved sampling method. Following the development and implementation of a sampling and analysis method to monitor alkali emission concentrations, QAL is conducting a number of feasibility studies evaluating a range of alkali emission reduction options. The alkali measurement method will be used to track and demonstrate progress in this environmental initiative. This paper will discuss the measurement method and emission reduction options being evaluated.

Jan 1, 2005

By A Weeks, W J. Shaw, A Kuk

Grade control is a process that requires the interaction between many components of the mining operation and successful grade control is only realised through good data, robust systems, and a well-trained, motivated and disciplined workforce.The Mt Magnet Gold Project Pty Ltd (MMGP), a wholly owned subsidiary of Ramelius Resources Limited, started mining at Mt Magnet in February 2012 with high expectations for success. Positive cash flow would fund an aggressive exploration and mine development program in the area to increase mine life. Disappointment followed when after start-up the operation had issues achieving budget grade and realising the predicted grade of the mined ore. In January 2013, things started to improve. During the next six months, gold production steadily increased with successive months achieving record production. What had changed?Improvements started following the realisation that controlling grade was not the sole responsibility of the mining geologist and that everyone on-site has a role to play. This paper examines the factors that delivered success for MMGP.CITATION:Weeks, A, Shaw, W J and Kuk, A, 2014. Who is responsible for grade? – an evaluation of the value chain at Mt Magnet Gold Project, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 477–482 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By M Andrew, D McTiffen, M Adams

A major Ventilation Upgrade Project commenced at the Fosterville Gold Mine (FGM) in 2017 to service the ongoing ventilation requirements of the underground mining operation. The project consists of three large diameter ventilation raises totalling 1100 metres, and new axial primary ventilation fans to upgrade the mine ventilation system. With a mining depth of 1200 metres and a thermal gradient of approximately 2.7 °C per 100 metres of depth, the completion of the Ventilation Upgrade Project is key to the ongoing success at FGM. The Ventilation Upgrade Project will allow continued mining, including high-grade gold deposits, lower in the mine where heat is increasing. Figure 1 below illustrates the underground workings at FGM, and provides a general view of the ventilation upgrade works to establish the new exhaust system from the lower workings to surface. Whilst raisebore pilot drilling the H4760 Return Air Rise (RAR) from surface to 395 metres, the raisebore drill string became stuck in the raisebore pilot hole at approximately 300 metres down hole, presenting a significant technical problem and delays to the project. This Case Study provides an overview of the recovery process undertaken at FGM including the recovery of the stuck drill string. The value of the stuck in-hole equipment, the investment in the shaft site preparation, the collar stabilisation, the underground development to the base of the ventilation raise, the surface footprint prepared for the Primary Fans construction and the limited available space on the site were all motivations to recover the raisebore drill sting and ultimately recover the ventilation raise location. More importantly, the long lead-time required should a new shaft location be the final solution, and the delay this would incur to the ventilation upgrade was unacceptable. Recovery of the drill string was not possible using the capability of the Contractor’s Raise Drill. An alternative method for freeing the drill string was required. A significant amount of engagement with industry was undertaken to seek out potential solutions and draw from the experience of others. All methodologies available were considered and assessed. Ultimately, after several attempts at freeing the raisebore drill string using various methodologies, Adams Drillers and Clear Cut Interventions were engaged to provide a turnkey recovery solution.

Mar 15, 2021

By A D. Bugarski, G H. Schnakenberg Jr

An investigation was carried out at a US underground mine to characterise diesel aerosols and to asses the effects of various control technologies on the concentrations and properties of particulate matter and gases emitted by heavy-duty diesel-powered equipment. This study was dedicated to evaluating the impact on mine air quality of contemporary diesel particulate filter (DPF) systems installed on mining equipment. Additional efforts were made to assess the effect of blended biodiesel fuels, yellow grease and soy, ultra-low sulfur fuel, a fuel emulsion and of selected diesel oxidation catalysts on air quality and emissions. The carbon analysis performed on the collected samples showed that the tested DPF systems reduced the mass concentrations of elemental carbon in mine air by between 70 per cent and 92 per cent. In addition, TEOM measurements, collected during these tests, showed that the total diesel particulate matter concentration in the mine air was reduced by greater than 65 per cent when DPF systems were used. The tested biodiesel blends were found to reduce elemental carbon concentrations in the mine air by between 49 per cent and 33 per cent, for the B20 (20 per cent biodiesel/80 per cent #2 diesel) of soy and yellow grease respectively and between 66 per cent and 56 per cent for the B50 (50 per cent biodiesel/50 per cent #2 diesel) of soy and yellow grease, respectively. The water-in-diesel fuel emulsion was shown to reduce elemental carbon concentrations by as much as 85 per cent. NO2 measurements showed an increase in the maximum concentrations of NO2 when catalysed DPF systems were used instead of mufflers.

Jan 1, 2005

Folklore suggests that oxidation is detrimental to sulfide mineral flotation, and in many instances is the reason given for values reporting in the tailing. However, while a considerable body of work examining galena oxidation is available in the literature there are very few studies that investigate the consequences of galena oxidation on its subsequent flotation in base metal sulfide ores. This work clearly demonstrates that pyrite forms a galvanic couple with galena, due to the large difference in their rest potentials, and results in accelerated oxidation of galena, particularly as the pyrite content of the ore is increased. The most obvious effect of the galvanic oxidation of galena by pyrite is the release into the system of galena oxidation products, providing an ample supply of lead ions available to activate gangue minerals, most notably of which in lead/zinc ores is sphalerite. The inadvertent activation of sphalerite by lead ions inevitably leads to the recovery of liberated sphalerite into the lead concentrate, and as a consequence a reduction in the lead concentrate grade. That is, a loss of selectivity for galena against sphalerite. If galena oxidation is excessive not only is there a considerable loss in lead concentrate grade, but also a marked decreased in lead recovery as the flotation rates of the gangue minerals increase, until they rival that of galena.

Jan 1, 2005

By P F. Hodkiewicz

"Our understanding of mineral resources relies on three basic steps: data capture data interpretation model construction. Until recently, all three of these steps required significant time and manual effort to produce a single resource model for mine planning, typically taking more than a year to progress from drilling to the final block model. Over the past several years, BHP Billiton has been developing innovative workflows in rapid resource modelling projects to significantly reduce these time constraints and make the process more productive by replacing manual activities with automated ones. Rapid resource modelling is the process of combining recently developed off-the-shelf technology with internal technology developments to fundamentally change the way we collect, interpret, model and evaluate geoscience data. Initiatives include automated systems and standardised workflows to make it safer, faster and cheaper to continuously update multidiscipline resource models. Specifically, rapid resource modelling workflows combine: real-time analysis of drill holes and drill samples with downhole tools and hyperspectral scanning systemsautomated interpretation of drill hole intervals based on pattern-recognition algorithmscontinuous modelling workflows using implicit modelling software. This paper outlines technology developments and workflows that provide a more thorough understanding of mineral resources to support faster and more informed strategic, planning and production decisions.CITATION:Hodkiewicz, P F, 2014. Rapid resource modelling – a vision for faster and better mining decisions, in Proceedings Ninth International Mining Geology Conference 2014 , pp 183–188 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By I M. Platten, S C. Dominy

The evaluation of historical goldfields is currently topical, reflecting a high gold price, improvements in knowledge and technology. and lack of greenfield sites. Many goldfields comprise narrow gold-quartz veins which are structurally complex with an irregular distribution of gold; variable geometry and architecture; and display late deformational effects. The study of historical mine records can be an important tool during early and advanced project evaluation since it contributes to understanding the orebody, exploration target size and setting expectations. The historic Engineer Mine property is located 32 km west of Atlin, British Columbia on the east side of Tagish Lake. The economically important Engineer and Double Decker veins belong to a NNE-SSW vein set. These are narrow, commonly <2 m dilational veins with a minor sinistral strike component and of an epithermal type. Documented ore production between 1910 - 1952 is recorded as approximately 14 263 t at 39.4 g/t Au and 19.5 g/t Ag (for 18 000 oz Au and 8950 oz Ag). The underground workings consist of about 5500 m of tunnels, shafts, raises and stopes over eight levels. The mine is currently being re-evaluated. In 2011, an Inferred Mineral Resource of 41 000 t at 19 g/t Au for 25 000 oz Au (at a 5 g/t Au cut-off) was defined from historical data supported by modern drilling into the Engineer and Double Decker veins. A surface and underground bulk sampling and milling program was undertaken in 2011.CITATION:Dominy, S C and Platten, I M, 2012. Application of historical data to estimate a mineral resource at the Engineer gold mine, British Columbia, Canada, in Proceedings Narrow Vein Mining 2012 , pp 81-100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By S J. Loach

F-Series reconciliations are formal comparisons of estimates and measurements of ore quantity and quality made at pre-determined points along the mining value chain. F1 is the ratio of ‘Depleted Grade Control Ore/Depleted Long-term Model Ore’ and validates the models upon which Resource and Reserve statements are based. F2 is the ratio of ‘Produced Tonnes and Grade/Depleted Grade Control Ore (-) Changes in Pre-Crusher Stockpiles’ and validates that the ore tonnes and grade delineated in the pit are being accurately extracted and correctly delivered to the processing plant. These factors provide important corporate assurance for a mining company by providing quantitative feedback on model-predicted tonnes and block grade estimates. Since 2009, BHPs Western Australian Iron Ore F-Series reconciliations have been calculated in a single, centralised sequel-server database. This software routinely collates data regarding mineral resource block model depletions, grade control model depletions, pre-crusher stockpile inventories and production tonnes and grade measurements and then calculates F-Series factors for both tonnes and product quality. This paper will present case studies where reconciliation factors were used to identify improvement opportunities leading to projects that improved our models and subsequent forecasts of production tonnes and quality. In addition, it will show how reconciliation factors are tools that monitor control during periods of rapid change and provide feedback on the effectiveness of improvement projects.

Sep 18, 2023

By B Young

Variable bench heights, interaction with underground workings and a steeply dipping orebody are challenges faced daily by geologists at Xstrata Zinc’s Black Star Open Cut (BSOC) Zinc/Lead/Silver mine in Mount Isa, Queensland.BSOC has been in operation since late 2004 and was developed to extract the surface extents of the Zn/Pb/Ag mineralisation mined in the underground lead mine. To date many large scale stopes and extensive development drives have been intersected and successfully mined. The stratigraphically hosted orebodies strike in a north-north westerly direction, dipping ~75° west. Ore production from the pit is currently at 4.5 Mt/a.Historically, sampling was conducted using a multiple spear technique from blasthole cuttings. This method proved to be relatively reliable when blasting benches at a consistent height, but a requirement to vary bench heights to safely collapse and then mine through underground workings reduced sample representivity to unacceptable levels.The purchase and commissioning of a production rig which had been converted for reverse circulation (RC) has allowed for the flexibility of a small rig, with the capacity to easily drill 48 m holes while ensuring sample quality. Sample quality is not the only benefit of introducing RC grade control. By collecting grade control data well in advance, informed decisions can be made by planning, drill and blast and mining departments weeks beforehand, rather than hours before firing. Additionally, seeking operational value to offset higher drilling costs has proved positive with benefits including increased confidence in orebody wireframes, accurate tonnage and grade for proceeding five benches along with the ability to representatively test metallurgical response on a tight grid spacing.

Aug 22, 2011

During underground mining, rock mass changes can occur as a function of the mining sequence and excavation processes. Mining-induced rock mass damage can occur due to redistribution of static stresses and the application of dynamic stresses from blasting and seismic activity. These rock mass changes can result in a degradation of strength of the bulk rock mass and the remaining rock surrounding existing excavations. Rock mass damage near existing excavations which lead to excavation-scale instabilities such as rock fall, excavation closure, or visible rock mass fracturing can detrimentally affect the safety and profitability of mining operations.The focus of the current work was the prediction and assessment of damage to mine infrastructure occurring in relation to the blasting of a sublevel open stope. The study case involved a 60kt stope located in a highly-competent rock mass at a large Australian sublevel open stoping mine. The mine infrastructure of interest for investigation included local stope access development, critical access and haulage development crossing a regional-scale fault, an explosives storage magazine and a ventilation return air raise. The methods used to predict or assess the blast-induced damage to each infrastructure element in response to stope extraction were:- intact rock strength testing,- discontinuity mapping,- linear-elastic static stress modelling,- blast-damage mapping,- near-field blast vibration monitoring and analysis,- geophysical assessment using inferred stiffness and wave velocity methods, and- post-extraction void assessment.The results of the detailed blast damage prediction and assessment program at the mine site have been discussed by the primary author elsewhere (Fleetwood, 2010). The current work will address blast-induced damage to mine infrastructure as a result of extraneous blasting vibrations from stope production blasting. A method for predicting the amplification of excavation surface motions from reflecting body waves will be discussed as well as the results of damage mapping around the study stope. The results of the damage mapping program identified blast-induced damage that occurred to the surface of the explosives storage magazine and local stope access development. No damage was observed at the main fault crossing or return air raise where higher vibration amplitudes were measured or predicted.

Dec 6, 2010

By E Thomas, L McCallum, G Dale, J Bennett, K Reardon-Smith, S Raine

Sustainable closure of coal mines in Australia to a safe, stable, non-polluting condition remains one of the industry’s biggest environmental and social challenges. A significant proportion of mines in the Bowen Basin of Queensland have dispersive spoil. Based on an estimated area of 20,000ha and a rehabilitation cost of AUD$100,000 to AUD$150,000/ha, the instantaneous rehabilitation liability for the Bowen Basin alone is estimated at AUD$2 to $3 billion.Dispersive spoils present problems in post-mining rehabilitated landforms due to increased potential for surface and tunnel erosion, compromising the ability to achieve fundamental mine closure objectives of a safe, stable, non-polluting and self-sustaining post-mining landform (Minserve, 2004). Dispersion results in clay particles being mobilised and transported in water, even at low flow velocities (So et al., 1998; Minserve, 2004), and blocking of soil pores, resulting in surface sealing, crusting and reduced permeability (DNR, 1997; Vacher et al., 2004) which, in turn, further increases runoff (Dang et al., 2018).CITATION:Dale, G, Reardon-Smith, K, Thomas, E, Bennett, J, McCallum, L and Raine, S, 2018. A process-based approach to mine rehabilitation decision making using Bayesian modelling and risk-based principles for dispersive spoil rehabilitation, in Proceedings Life-of-Mine 2018, pp 106–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By E Williams

The role and importance of a well designed test work program during the development of an orebody is often underestimated. A test work program should be tailored to deliver very specific answers to relevant questions. With a clear purpose, the results from the test work program will enhance the outcome of the feasibility study and provide the information required to meet the requirements of all stakeholders. With regard to test work programs there are three main areas that should be considered: orebody characterisation and definition, process flow sheet development and engineering design information.Orebody definition relies on reliable analytical methods to characterise and assess the economic minerals present in the ground. In mineral sands, the physical processing characteristics of the minerals play a significant role in the definition of an orebody. The analytical method therefore has to be customised using a combination of laboratory techniques. These techniques can include heavy liquid separation, gravity separation and magnetic separation and are usually combined with chemical and mineralogical analyses to create a picture of the orebody. During the definition phase of test work programs, an appropriate analytical technique has to be developed to evaluate drilling samples, but also to support the information collected during flow sheet development.Process flow sheet development is usually done once there is a reasonable understanding of the size and variability of the orebody. Selecting the best sample for test work is critical, as any flow sheet design is tied to the specific characteristics of the sample used for development. There are other factors that can improve the outcomes of flow sheet development test work, including the skills and knowledge of the operator and allowing sufficient time to process and analyse the results. Very often this work is conducted under pressure with limited time and resources, only to result in a suboptimal flow sheet. During this phase of flow sheet test work, iterative testing will provide the information required to develop an optimal metallurgical flow sheet. The data collected will provide indicative recoveries and yields that are required for feasibility studies.Equipment specification is often included as part of process flow sheet development. This includes comparative test work between different equipment suppliers, assessment of operating conditions such as the loading to determine the number of processing units required, as well as other design information required such as particle size distributions, density and operating temperatures.While restricting the time and costs expended on test work programs may seem to meet a short term need to meet investor requirements, neglecting to develop a proper framework of the requirements that has to be met in the long-term can lead to significant long-term cost overruns. This is mainly due to a need to repeat test work, or do confirmation test work, as insufficient information was collected during the initial program.

Oct 5, 2011

By S Gezgin, F Beckstein, M Müller, D Rapp, D Sergeev, J Qi, A Lichtinger

Salts and their mixtures play an important role for industrial and energy sectors, eg metallurgy, biomass gasification and combustion, nuclear and solar powerplants and electrochemical processes. Depending on the composition of salts (eg Li+, Na+, K+, Mg2+, Ca2+ // NO3-, F-, Cl-, CO32-, SO42-, etc), the temperature range for different applications can vary starting from room temperature and going up to 1500°C. For the proper design and modelling of heat exchangers and other equipment, it is necessary to have reliable and validated data sets of thermophysical properties. The 50 mol per cent NaNO3 – 50 mol per cent KNO3 salt mixture as a well-studied composition was selected for validation of relevant thermophysical properties (heat capacity, enthalpy of phase transitions, thermal expansion, viscosity and thermal conductivity). To study these properties of the liquid phase, special crucibles and approaches should be implemented. Verification of these crucibles for different methods (differential scanning calorimetry (DSC), thermomechanical analysis (TMA), laser flash analysis (LFA) and rheometers) has been performed. The low thermal conductivity of salts is one of the main problems in implementing latent heat storage. In this project, the authors intend to develop a fundamental solution to this problem using chemically bonded metals with salts. These are known as metal-salt solutions. To fit the main parameters of new phase change materials to the requirements of thermal energy storage, a wide variety of possible combinations should be considered. CALPHAD modelling is used together with thermal analysis for the development of a consistent thermodynamic database including chloride salts (Li, Na, K, Mg, Ca // Cl) and corresponding metals (Li, Na, K, Mg, Ca). The results of the study of quasibinary and multicomponent metal-salt (eg Mg-KCl and Ca-KCl) systems as well as the selection of suitable crucible materials and challenges by studying of these systems will be discussed.

Aug 21, 2024

All large open pits in Australia have been mined, or are planned to be mined well below the local water table. This raises several issues that impact on mine safety, mining costs and regulatory approvals. Some pits will be æwetÆ, where they are mined through permeable horizons and where there will be measurable groundwater inflows. These will require some form of dewatering. There may also be some difficulties in the disposal of excess water. Other pits, may be ædryÆ, where they are mined through impermeable material and there are no measurable groundwater inflows but where there are stability issues related to hydrostatic pressures within the pit walls. These may require some form of depressurisation. Some pits are a combination of both. Effective management of groundwater inflows and groundwater related stability issues and the development of cost effective and environmentally acceptable dewatering and depressurisation systems requires an understanding of site specific hydrogeological conditions and practical experience in what works best for different conditions. The presentation will include an outline of the key hydrogeological factors that impact on large pits, practical methodologies for achieving dewatering/ depressurisation, and some case studies from the Goldfields, Pilbara and North Queensland.

Jan 1, 2003

By Emerson D. W

The search for economic mineral deposits is becoming more difficult as exploration goes deeper in the established mining camps and spread out to the surrounding covered areas, which may have an `overburden' some hundreds of metres thick. Geophysics is finding an ever increasing role in such exploration. When the target is zinc, the task often becomes even more difficult since sphalerite, the most commonly mined mineral, is non-magnetic, resistive, and relatively light compared to other sulphides. Fortunately, sphalerite commonly occurs in association with other sulphides, which are magnetic and/or conductive and/or heavy, thus most zinc-rich orebodies have at least one contrasting physical property to aid exploration. This paper presents the physical properties of sphalerite and other potentially important zinc minerals. Results of petrophysical measurements of samples from various zinc-rich ores are presented together with examples of geophysical surveys over a number of zinc deposits. The results show that the physical properties are not merely dependent upon the properties of the orebodies' constituent minerals. For example, the small (0.4 Mt) and low-grade (five per cent Zn + three per cent Pb + two per cent other sulphides) Flying Doctor deposit at Broken Hill, New South Wales (NSW) is much more conductive than the large (3+ Mt) and high grade (14 per cent Zn + five per cent Pb) Cadjebut deposit in Western Australia (WA). In the former case, tectonic stresses have

Jan 1, 1993

By S Khosrowshahi, A Weeks, W J. Shaw

"To provide an indication of expected performance of the mine and mill, feasibility studies should include an assessment of the expected day-to-day variability in process plant feed. Attempts to do this based on conventional resource models will be flawed as such studies fail to consider and account for the in-built smoothing (averaging) of input data.This can lead to one of two situations: an expensive, over-engineered process plant that can cope with every possible situation, or operational strategies that fail to manage the natural variability within the orebody and the impact of day-to-day operational decision-making.In both cases the value of the project diminishes through excessive capital costs or reduced throughput or recovery during operations.Unlike conventional estimation techniques, the geostatistical method of conditional simulation can reproduce the inherent variability of the deposit. Once a valid model has been developed, it is possible to analyse the model using a transfer function that simulates the proposed mining processes and provides a representation of the likely variation of mill feed characteristics at any time scale.The case study demonstrates how the proposed mining strategy would result in mill feed being considerably more variable than expected, resulting in poor recovery, low throughput and potential breaches of environmental conditions. Mitigation measures included budgeting for additional mining equipment to enable greater flexibility during mining and revised stockpiling and crusher feed strategies.Awareness of the benefits of modelling the variability of geometallurgical parameters will increase the use of this approach in producing more realistic financial models of expected mine performance at the design stage.CITATION:Shaw, W J, Khosrowshahi, S and Weeks, A, 2013. Modelling geometallurgical variability - a case study in managing risk, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 247-252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By P Hogan, M Wells

Reflectance spectroscopy has become an established technique for mineral exploration and ore characterisation. However, there are few reported cases where the technique has been applied to the Hamersley Province channel iron deposits (CID). The Bonnie Creek CID, located ÿ140 km north of Newman in Western Australia, represents one of a number of CIDs recently discovered in the Hamersley Province. Reflectance spectroscopic analysis using the CSIRO HyLoggerÖ automated scanning system, in conjunction with X-ray diffraction and compositional analysis, was used to characterise and map the ore and gangue mineralogy in CID drill core. Using CSIROÆs spectral mineral characterisation scripts, it was possible to map the downhole distribution of the Fe-oxide abundance, hematite:goethite ratio and the gibbsite and kaolinite abundance. Spectral estimates of kaolinite abundance were found to be closely related to loss on ignition measurements at 650¦C and the spectral kaolinite abundance index provided a reliable estimate of the total weight percentage Al2O3 content. In addition, downhole HyLoggerÖ scanning of diamond drill core reliably mapped the distribution of kaolinite as supported by coincidentally elevated contents of alumina and silica. Furthermore, spectrally-derived estimates of iron oxide abundance were well related to assayed Fe wt per cent contents and use of the spectral iron oxide mineral index mapped the distribution of the goethite:hematite ratio, and demonstrated that material logged as high-grade ore in the Bonnie Creek CID was predominantly goethite-rich.CITATION:Wells, M and Hogan, P, 2013. Bonnie Creek channel iron deposits ore mineralogy - insights using the HyLoggerÖ technology, in Proceedings Iron Ore 2013 , pp 321-328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

In a ætypicalÆ gold deposit each tonne of ore will contain tens of millions of very fine gold particles, whereas; at Bendigo the majority of gold in each tonne of ore is present in just five to 15 very coarse gold particles, a distribution more akin to diamond deposits. At Bendigo the minimum sample size required for good assay repeatability is estimated at 4.5 t for each assay. Drill core samples are several orders of magnitude too small to generate representative assays.The drilling data are characterised by a nugget effect approaching 90 per cent, a very skewed distribution and, on average, under-report in situ grade by 50 per cent to 75 per cent. Since 2002 Bendigo Mining NL has completed 47 000 m of diamond drilling, 1200 m of on reef development, collected and processed 100 bulk samples (150 t each), 800 mini bulk samples (50 kg each) and processed in excess of 25 000 t of ore through a pilot plant. The results of this work have provided the information required to develop and verify a robust grade estimation procedure. No standard geostatistical manipulation of the drilling assay data can generate an accurate grade estimate as the samples and associated assays are not representative of the ore being sampled. The recognition of this fact was critical as a radical transformation of the raw drill assay data was required to develop a workable methodology for grade estimation in such a high nugget environment. The aim of the transformation was to reduce the nugget effect and high variance and so approach a lognormal assay distribution. Ideally the average drill grade would approximate actual in situ grade and the assay distribution would reflect actual grade distribution within the reefs. Following the data transformation simple block modeling within the defined resources allows grade estimates to be made that can be used in the estimation of Indicated Resources and hence Probable Reserves. The grade estimates have been checked by extensive bulk sampling and processing of 25 000 t of ore (three per cent of total resource) through a pilot plant with planned full scale mining to provide the ultimate verification.

Jan 1, 2004

By T N. Little

This paper is concerned with the influence of engineering geology on design of Wall Control Blasts. In the Introduction, the Blast Management Framework and the Blast Design Requirements classification system (previously developed by the author) is drawn upon to set the context. Blasting objective for all wall control blasts involves both profile and damage control. Four classes of approaches for blast design are outlined and briefly discussed. Five distinct wall control blasting techniques are summarised. The general relationship between geology and blast design is explored in the paper. Influence of geology on pre-split and post-split design and blasting direction is highlighted. Wall damage modelling from the closest row of blastholes is also introduced using the Analytical Damage Model (ADM). The relationship of rock properties and explosive selection and in particular the Mach wave generation is introduced to assist blast designer in this regard. Finally a Conceptual Model that relates vibration, damage and rock mass condition has been presented along with some applications that have been undertaken by the developer. Eight conclusions have been formulated based on extensive work in this area and the current study.

Jun 22, 2022

By Roberts AW

Bulk materials handling operations depend on efficient storage and gravity flow facilit- ies. ,It is important that proper attention be given to the complete storage bin or stockpile and feeder combination. The paper briefly des- cribes the principles of efficient feeding and discusses the common types of feeders under practice. While ideally unaided gravity flow should be sought, occasions arise where flow promotion is necessary. Various types of flow promotion devices are described and their operational features evaluated.

Jan 1, 1978