Search Documents

By H Ishikawa, S Palaniandy

The gravity-induced stirred mill such as the TowerMill is an energy-efficient grinding solution used in secondary, tertiary, and regrinding duties in the mineral processing concentrator. The interest in this technology is emerging, with more than 300 mills installed globally in various grinding duties and commodities for the last 30 years. Although the technology is matured, there are still opportunities for improvement and the development of new knowledge to improve its circuit energy efficiency and reduce water consumption. Recent studies show that a combination of stress intensity, ore hardness, slurry density, and mill feed configuration can be used to evaluate the performance of the grinding circuit. A recent pilot-scale TowerMill test work at various stress intensities shows that a lower operating work index and size-specific energy were achieved at higher agitator tip speed and using medium size grinding media. These outcomes were confirmed through several site trials. A smaller 17 mm grinding media has reduced the operating work index and size-specific energy by 18 per cent and 11 per cent, respectively, compared to the 20 mm in a magnetite concentrator. Moreover, the conversion from top feed to bottom feed configuration has reduced the operating work index and size-specific energy by 13 per cent and 37 per cent, respectively. The circulating load was reduced by 34–38 per cent, leading to a reduction in the dilution water consumption in the hydrocyclone feed sump by 20 per cent. A variable frequency drive offers flexibility to change the stress intensities on the TowerMill, where a 35 per cent reduction in specific energy was achieved when the ore became soft. This paper explores the potential design and operating strategies that can be implemented to enhance the energy efficiency, reduce water consumption and reduce CO2 emissions in the circuit and finally evaluate its impact on the total cost of ownership.

Aug 24, 2022

Diamond bearing deposits are extremely low grade and require large bulk samples to be tested to determine the grade and quality of the stones. The semi portable plants, for treatment of these bulk samples, have followed the development of commercial processes for diamond concentration. These processes included jigs and diamond pans, which have been largely supplanted by heavy media processes for primary concentration, due to the higher efficiencies in all size ranges. A number'of flowsheets including these processes are presented. The final recovery of diamonds from the bulk sample concentrates can be accomplished by rejigging, adherance to grease or by X-ray sorting. Flowsheets incorporating all the processes are presented. Two plants are described; one incorporating jigging, rejigging and hand sorting; the other using heavy media separation, and wet X-ray sorting.

Jan 1, 1984

By R van Berkel, J Lay, D van Beers

The development of regional resource synergies in intensive areas with concentrations of minerals processing industries provides a significant avenue towards sustainable resource processing. Gladstone (Queensland) and Kwinana (Western Australia) are two of AustraliaÆs major heavy industrial areas. There are a number of successful regional synergies in both areas. In addition to the existing regional synergies in both areas, more potential synergy opportunities appear to exist which, upon implementation, could benefit industry, the environment and the community. To further enhance the development of such potential regional synergies, the Centre for Sustainable Resource Processing (http://www.csrp.com.au) commissioned research projects to facilitate the identification of potential synergies and assist with their implementation in both regions. This paper presents a selection of specific examples from both regions to illustrate the sustainability benefits from regional synergy developments. Although the composition of industries in the Gladstone and Kwinana regions is different both in terms of geography and industry diversity, similarities in synergy developments for both regions are apparent. Consequently, the examples discussed in this paper are organised around the key themes of water, energy and inorganic by-products. Comparison on a theme basis highlights success factors of successful synergies and demonstrates the range of benefits resulting from their implementation.

Jan 1, 2006

By G Hart

As the iron ore/magnetite boom gains momentum, it is particularly important to question established past trends and explore the potential of alternative design options. Traditionally, ‘rule of thumb’ methods have been used to size dewatering equipment. Greater consideration needs to be given to technological advancements and specific throughput testing of each ore body type based on innovative developments.This paper will describe how an innovative approach resulted not only in significant savings in capital cost and site work hours but also delivered a truly optimised design for the thickener duty at Karara. Test work also played a crucial role and a comprehensive test work program on the ore samples showed the scale-up benefi ts of new technology in thickener designs. Working closely with the Karara team during the laboratory testing proved the old sizing theories for iron ore/magnetite processing have been superseded with the knowledge and results of the industry’s newest feedwell technology. Increased solids flux and rise rates in the testing process proved very successful, resulting in signifi cantly reduced thickener sizes and lower capital expense.Mechanical design considerations such as removal of underflow and pump access led to a preference for an above-ground thickener confi guration, and the economics of a completefabrication and installation package favoured steel construction for the thickener units.The ultimate choice of the bolted/fl anged tank methodology provides both economic and timely solutions for the site installation including reduced man power and quick and safe site-work. A benefits comparison between this design and other fabrication and installation procedures will also be analysed in the paper.

Jul 11, 2011

By H Wang, D Wang

Mine dust is the most serious occupation hazard in coalmines. And many coal workers suffer from pneumoconiosis because of long-term inhalation of respirable dust. Reducing the dust concentration of workplaces by effective technical means is an important way to prevent coal worker’s pneumoconiosis (CWP). In order to overcome deficiencies in existing dust control technology for underground mining, especially the disadvantage of water spray technology mounted on roadheaders or continuous miners, the authors developed an integrated dust suppression technology utilising foam for fully mechanised heading faces. This paper presents an overview of the principles, materials, equipment and application of this technology. Among these, a jet type foaming device and a green foaming agent were developed, which can realise the goal of efficient preparation of foam. In addition, an arc fan nozzle used for foam spraying was invented, which can effectively cover and enwrap the dust produced by the roadheader at the cutting point and achieve the goal of efficient utilisation of foam. This dust suppression application of the proposed foam technology was investigated on fully mechanised heading faces. The results show that the dust concentration was cut down significantly with a dust suppression efficiency of greater than 85 per cent, an increase of over 30 percentage points compared to the water spray system. This study demonstrates that this foam technology can play an important role in dust suppression on fully mechanised heading faces, which provides an important method to improve the working environment and protect coal workers’ health.CITATION:Wang, D and Wang, H, 2015. Technology of dust suppression by foam for fully mechanised heading face, in Proceedings The Australian Mine Ventilation Conference, pp 177–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

BHP Billiton Olympic Dam produces copper cathode, uranium oxide concentrate and refined gold and silver. The operation is comprised of an underground Mine and Processing Plant and is located 560 km north of Adelaide. Water for the operation is sourced from two wellfields located 120 and 200 km from the operation in the Great Artesian Basin (GAB) at a rate of approximately 36 ML/d. Regulatory drawdown limits were established to protect regional GAB springs and are monitored at compliance bores. Drawdown was predicted in the æOlympic Dam Environmental Impact StudyÆ (Kinhill, 1997); however, pumping at higher volumes may have the potential for increased drawdown resulting in a trend towards the compliance limits. In recent years increased usage of water in the Concentrator and Hydromet sections of the Processing Plant has caused excess process water reporting to the Tailings Retention System (TRS). This has resulted in excessive amounts of liquor ponding on the tailings cells with a potential impact being contamination due to seepage of liquor to groundwater. Effective management of water by the operation is necessary to both reduce GAB drawdown and reduce the amount of liquor on the tailings cells. A site working-group has been established to investigate and pursue opportunities to improve the water use efficiency of the operation. This paper will highlight the issue of water management at Olympic Dam and discuss the various options currently being investigated to improve management of this important resource.

Jan 1, 2006

Kinetics of bubble-particle interaction, surface hydrophobicity and interfacial phenomena in sulfide mineral flotation are discussed in this paper. Results of the measurements of a bubble and mineral induction time (IT) and detachment force (DF), vacuum of bubble evolution (VE) and mineral floatability are discussed for pyrite, galena, chalcocite and chalcopyrite. Natural wetting and wetting induced by xanthates with different lengths of alkyl chains are examined. Experiments show the existence of several maxima of hydrophobicity on dependences of pH and electrochemical potential. These maxima are attributed as the reflection of mineral surface heterogeneity due to xanthate adsorption and the presence of cationic and anionic centres with uncompensated positive and negative charges. These charges can be neutralised by both regulation pH and applied potential. The aim of this paper is to evaluate a thickness of the rupturing film and to estimate how long the bubble-mineral interactions are according to the experimental values of IT, in order to develop a procedure for comparing of the results of DF and atomic force measurements in the same dimensionality, and to compare the results of the experimental studies on the wettability of sulfides with those predicted by the models of physics of capillarity.

Jan 1, 2005

By S N. Donaldson, B L. Hollis, K Wynn, L Potts, M Evans

A real-time load-haul-dump (LHD) dispatch optimisation tool has been deployed at Panel Cave 1 and Panel Cave 2 at Newcrest’s Cadia Valley Operations. The tool, known as ORB, is the first known successful implementation of an optimisation-based, autonomous, real-time dispatch tool, custombuilt for underground mining operations. ORB can co-ordinate the optimal dispatch of LHD’s in a block cave to achieve a range of objectives while adhering to draw compliance and geotechnical constraints. It is an example of highly automated short-term interval control. This paper starts by outlining the pre-existing business planning process, detailing the simple logic that produced the daily draw order. Next, the motivations for a real-time dispatch tool are presented, drawing comparison to the limitations in existing planning processes and how these can be overcome through an optimisation-based, autonomous, real-time dispatch tool. Subsequently, the paper details the Ratio Bogging Draw Strategy, through which tonnes targets are expressed continuously on draw bells or draw points as a ratio of total cumulative cave draw. This signifies artificial planning boundaries are removed and that draw targets are linked within a cave; such that tonnes are unlocked by bogging other parts of the cave, instead of as a function of time. This creates incentive within the target mechanism for fixing and bogging struggling draw areas whilst allowing uncapped progress if all draw targets are progressing within compliance. Furthermore, the optimisation tool developed is outlined, including the data it uses and the objectives it optimises. Finally, detail on the improvements to operations the implementation of this tool has brought, and the business process change it has facilitated are presented using Newcrest’s Cadia Valley Operations as a case study.

Mar 15, 2021

By A Harding, M Chappell

Precast concrete segmental linings have enjoyed widespread use around the world, and are the lining type of choice for tunnels constructed using a shielded tunnel boring machine. However, there is significant variation in the design of such linings from one country to the next in such areas as materials, geometry, fixtures and fittings, waterproofing and reinforcement to name but a few. This arises because the speed at which the technology has developed within some countries and regions has sometimes outstripped the transfer of such technologies to the rest of the world.This paper provides some insights into the variations in lining design in different parts of the world with the aim of providing designers and constructors alike a reference for the different methods adopted. It provides a context for these developments by briefly summarising historical reviews of this subject before looking at some of the developments around the world over the last 15–20 years. The developments are presented with some reference to the reasons for implementation, and the advantages and limitations commented on. Following on from this description of the state-of-the-art, the authors also provide their own views on what developments we may see in this area in the near future.CITATION:Harding, A and Chappell, M, 2014. Precast concrete segmental tunnel linings – the state-of-the-art, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R Skirrow, E Bastrakov, A Mauger, P

A new rapid spectroscopic core and chip logging and imaging system developed by CSIRO was evaluated by PIRSA and GA on a wide variety of mineralised properties in South Australia, including the Emmie Bluff, iron oxide copper-gold-style prospect on the Stuart Shelf. During a three-month campaign in South Australia in 2003 the system logged over 50 000 metres of core from the State Core Library, company prospects and mines. The new system uses automated core tray handling, continuous visible and infrared spectroscopy, and digital imaging, to characterise and identify dominant mineral species on core, chips and pulps, at spatial resolutions of ~1 cm (spectral data) and ~0.1 mm (image data). The system can log up to 1000 m of core per day and several thousand metres of drill chips. Mineralogy is pre-interpreted using specialised identification software trained on a selected suite of minerals showing characteristic absorption features within the measured spectral range. On core from the Emmie Bluff iron oxide copper-gold prospect, 470 km NW of Adelaide and 80 km SSE of the Olympic Dam Cu-U-Au deposit, the spectral mapping system was able to characterise a number of alteration zones enveloping the sub-economic Cu-Au mineralisation. These consist of distal white mica phases showing decreasing Al content towards mineralisation, a zone of increased iron oxide content in the hangingwall to mineralisation, and a zone proximal and coincident to Cu-Au mineralisation that is enriched in chlorite with variable Mg/Fe chemistry. Additionally the results show background spectral characteristics that mimic the magnetite distribution.

Jan 1, 2004

By Restarick C, Jowett A

A cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone plus in some tests a variable cyclone spigot, has been used to achieve classifier separations at unusually coarse sizes relative to the diameter of the units used. The method has proved to be useful for low tonnage flows at low pulp density and variable feed rate. The system relies on use of a cylinder unit to reject excess water and fine particles, the amount rejected being adjusted by the flow control valve. The valve also adjusts flow rate and pulp density of feed to the cyclone unit, and can be adjusted to give a separation at a coarse particle size. The system has been used in connection with experiments on the pilot plant at Mount Isa, where a 76 mm system was used to classify feed to the lead secondary rougher circuit at sizes as coarse as 52 micrametres galena equivalent for split conditioning tests. Further tests have been carried out with quartz to assess the range of size separations Possible.

Jan 1, 1978

The creation of an accurate and precise enough database requires the collection of many representative samples, subsampling and assaying them without destroying their integrity. The selection and implementation of sampling protocols often lead to severe difficulties, making the unaware practitioner vulnerable to massive exploration, feasibility and operating failures. Therefore, there is no substitute for a good understanding of the Theory of Sampling (TOS). Either because of ignorance, or because of short-term economic reasons, failure to comply with many stringent conditions can be devastating for the validity of a feasibility study, leading to false evaluations, to the abandonment of a viable property, or to the exploitation of one that is not profitable. All these failures have something in common: insufficient duplicate sampling, subsampling and assaying were performed; very important, preliminary heterogeneity tests were never performed; for short-term economic reasons, poor sampling and subsampling protocols were selected, second-class sampling systems and weightometers were installed and poor preventive maintenance and cleaning were implemented;and sampling experts were called only when the project was obviously in trouble. The conclusion is clear: in due time, iterative auditing of sampling practices is an insurance policy against massive financial losses for the company involved. A complete, comprehensive 100 point checklist of sampling Quality Assurance and Quality Control is provided, so critically important details to ensure success are not forgotten.

Mar 1, 2010

Laboratory studies of batch and continuous screening of ferrous sinter mixtures (4-0.5 mm) are described. The results are analysed by an equation derived from the first-order rate law for the condition of decreasing screen residue.The results of the studies show that the two screening operations are comparable in all respects if deck length in continuous screening and time in batch screening are interchanged.It is shown that the general screening process is determined by the numerical values of the screening rate constants of each of the particle sizes in the feed mixture and that the relationship between these constants and the particle size/screen aperture ratios is related to the appropriate probability function of the same ratios.It is also shown that the screening rates decrease exponentially with the amount of near-mesh material present in the feed and that oversize particles can increase these screening rates for some screen motions and decrease them for others.

Jan 1, 1985

By M I. Pownceby, N A. S Webster, J R. Manuel, J M. F Clout, E Donskoi, N A. Ware

The relative influences of sinter mineralogy, sintering temperature, solid and pore macro- and microstructure on iron ore sinter physical strength are not yet fully understood. Whilst a range of analysis techniques have been used by researchers to evaluate sinter physical properties and sinter mineralogy, none have been able to directly link sinter mineralogy and physical strength under controlled conditions. CSIRO has developed a unique laboratory method to study the fundamental melting properties of fine iron ores in a laboratory furnace under a controlled temperature and gas atmosphere environment designed to simulate the industrial sintering process. Compacted tablet samples for a 0.41 per cent and a 2.5 per cent Al2O3 series were fired in a tube furnace at various temperatures, cooled, then tumbled using a modified Bond abrasion test apparatus to determine a relative tumble index (TI) at each temperature. Quantitative XRD (QXRD) analysis was then carried out on the tumbled samples and optical image analysis (OIA) was conducted on polished sections of a separately fired compact in each case. The amount of total SFCA was found to decrease with increasing firing temperature for both alumina series with the total amount of SFCA higher in the 2.5 per cent Al2O3 series compared to 0.41 per cent Al2O3 series samples. The increase in the amount of magnetite and hematite with increasing firing temperature was largely at the expense of a decrease in total SFCA. Overall, there was good agreement between the quantitative mineralogy determined from QXRD versus OIA for SFCA, hematite and magnetite. Qualitative analysis of high magnification images of the sinter correlated with both the OIA and QXRD results.

Sep 18, 2023

RME has a vision for a new mill operational paradigm made possible by RMEÆs fast, safe Mill Relining System. This vision can be moved forward into reality at any time with or without guidance from recent development in measurement and predictive modelling tools.Some new liner designs can degrade SAG mill performance because of mill volume loss, ball strike (rotational speed limitations) and other issues often brought about by optimising liners for life and without a backward glance at metallurgical consequences. Freshly relined mills can initially produce as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the linersÆ wear life. RMEÆs proposition is to design new liners for maximum commercial performance. This may mean more frequent changes of liners but with liners designed to yield optimum grinding, metallurgical and profitability performance. In other words, mill liner profiles and mill relining speed become key operational controls and not simply æmust doÆ maintenance functions. Taken to the extreme, liner profiles may prove capable of ætuningÆ a grinding plant for maximum profitability in any metal price environment. This paper provides an update regarding RMEÆs fast, safe Mill Relining System technologies and outlines RMEÆs vision of a æliner profile versus profitabilityÆ model as a function of metal price, developed intuitively or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum commercial outcome, off-line in the virtual world, before committing to an expensive liner experiment.

Jan 1, 2006

By D Mather

Fibre reinforced shotcrete has long been accepted as temporary ground support in both mining and civil tunnel linings. Greater knowledge and understanding of shotcrete as an engineering material and advances in its quality have enabled designers to eliminate the requirement of a second pass lining. The initial shotcrete can be used as the permanent tunnel lining or be incorporated into the final lining design, rather than ignored and considered as sacrificial.For the initial shotcrete lining to become a suitable permanent tunnel lining it must be able to establish and maintain stability over time when subjected to all possible loads. To ensure this, best engineering practices are required during the design phase of the project to analyse; ground conditions including rock mass properties, ground and ground water quality, rock mass loadings, excavation sequencing, and construction methodologies.The increased durability of steel fibre reinforced shotcrete over traditional tunnel support, in the right ground conditions, makes it possible to achieve a serviceability design life of greater than 100 years (as required in most infrastructure projects). By specifying a good quality shotcrete mix and ensuring adequate quality control for batching, fibre dosing, preproduction testing, excavation sequencing, and application control, it is possible to eliminate the requirement of a secondary lining. The properties of a suitable permanent lining must be well established using suffi cient preproduction testing in combination with post application monitoring.A major benefit of steel fibre reinforced shotcrete in ground support applications is the removal of any requirement for workers to work under unsupported ground. Its use can also significantly reduce, if not eliminate, the manual handling associated with placing traditional reinforcement such as lattice girders and mesh. Both of these benefi ts are significant with the ever increasing focus on health and safety.This paper highlights factors that must be considered in the design and specifications to enable an initial shotcrete tunnel lining to become the permanent shotcrete tunnel lining.

Mar 8, 2011

By E Jak, P Hayes, J Chen

The paper provides an overview of the various analytical and microanalytical techniques currently in use to characterise the outcomes of pyrometallurgical processes, examining the advantages and limitations of these approaches. Specific focus with be given to quantitative microanalysis techniques including electron probe microanalysis and laser ablation, covering general principles, capabilities and limitations and recent development to address specific challenges associated with analysing molten slag, matte, and alloys, highlighting the necessity of embracing the application of these and other innovative analytical methodologies.

Jun 19, 2024

By Howes PM

In the iron and steelmaking processes, dusts are generated and treated by wet dedust- ing methods to form slurries which are high in iron content, but also contain certain impuri- ties. For many years these slurries have been processed and the wet cake, which is produced, has been dumped because of the high zinc and alkali chloride contents. Sintering is an appropriate process for recycling of these materials, provided the deleterious impurities can be kept under control. Zinc is a deleterious element in blast furnaces because it promotes the formation of accretions on the upper walls of the furnace. This results in irregular furnace performance. Alkali chlorides effect the emissions from the sinter plant waste gas due to the high resis- tivity of these components, resulting in decreased efficiency of the electrostatic precipitator. Experimental work indicated a concentra- tion of zinc in the -11 pmt particle size frac- tion. A cyclone plant was installed producing a "coarse" usable product and a "fine" waste Product.

Jan 1, 1984

By G Simpson, S Dressler, A E. Levett

Tailings storage facilities often represent a mining operation’s most significant liability, posing serious environmental, social and safety risks. Almost all mining operations dispose of wet tailings (Valenta et al, 2023), which represents a risk of failure due to the potential for a rapid strength reduction of the unconsolidated materials leading to static liquefaction and subsequent dam wall failure. As a waste stream, tailings disposal, decommissioning and relinquishment aim to be inexpensive processes, ruling out many highly engineered solutions. Advantageously, tailings consolidation does not need to be immediate, opening the door for relatively passive, inexpensive consolidation methods that aim to gradually increase the strength of tailings over extended periods (ie years). In this paper, we present the prospect of novel in situ tailings stabilisation, learning from studies that have investigated the most erosion-resistant landforms on Earth.

Aug 2, 2023

The Ernest Henry Mine is an open pit copper-gold mining operation located in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current concentrator throughput of approximately ten million tonnes per annum. The pit will cease mining towards the end of 2010. Extensive surface diamond drilling has confirmed an extension of the orebody to depths of 1000 m below surface. A prefeasibility study was commissioned in late 2006 to investigate underground mining options with the preferred mining method being an inclined sublevel cave. In February 2008 mining of a decline commenced in conjunction with a feasibility study to further investigate the project. Work from the prefeasibility study indicates that an underground crusher, conveyor and hoisting shaft could be utilised to crush and transport broken ore from the sublevel cave workings to the concentrator. The study suggests that a production rate of five million tonnes per annum could be achieved and sustained for up to ten years. Ventilation designs and requirements will form a large section of the feasibility study. This paper will detail investigations of preliminary ventilation network designs of the proposed sublevel cave. Work has been completed using both Ventsim and VumA ventilation simulation packages. Ventsim was used to provide preliminary estimations and suggest alternatives for: surface fan duties;airflow characteristics (direction, velocity, pressure and quantity); andventilation network design in key mine areas. With mining activities reaching depths in excess of 1000 m below surface an analysis of heat conditions should be conducted. The VumA software package was used to model the thermal properties of the ventilation system. This model will provide a basis for the preliminary decisions on refrigeration requirements for the mine.

Jan 1, 2008