Search Documents

By Kuganathan K, Potvin Y

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: 1. a minimum filling rate of 250 ma/h, 2. a curing time of 28 days, and 3. minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

By P Corbett, P Sheffield

Centennial Coal operates the Springvale longwall mining operation which extracts coal beneath the Newnes Plateau in the Western Coalfields of New South Wales. Springvale, and the neighbouring Angus Place mine, have a history of difficult geotechnical conditions where combinations of a relatively high stress regime and weak, laminated roof and extensive geological faulting has led to numerous roof failures throughout the mine’s life. Following development, the mines underground roadways can experience high levels of roof movement which may lead to roof falls. Multipoint wire extensometers are extensively used throughout the mine for roadway condition monitoring, and to reactively drive remedial strata support through trigger action response plans (TARPs).As a result of the use of high-density extensometer monitoring over a long period, the mines have an extensive archive of legacy data. Data processing has evolved over time in order to accommodate the increasing data volume, including direct data entry from the recently introduced hard-wired real-time monitoring instruments. It is likely that telemetric real-time instruments will be introduced in the future, which will cause another step change in data management requirements. This paper discusses the transition to and evolution of relational database management systems for extensometer and associated data.This paper also presents case studies of the use of a new software tool for reprocessing legacy data to enable time-scaled visualisation of monitoring data in the context of longwall and development face positions and installed strata support. The software can be used proactively in the identification of geotechnical risk factors and their interaction with the mining process to allow a more robust geotechnical hazard process. It interfaces directly with the widely used ExtoChart database software and can be presented with scale drawings of geological and geotechnical data to allow correlation of monitoring data results with risk factors.CITATION:Corbett, P and Sheffield, P, 2015. The use of high-intensity monitoring data to better characterise geotechnical properties of a non-homogeneous rock mass, in Proceedings Third International Future Mining Conference, pp 145–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By R Castedo, P Segarra, L M. López, J A. Sanchidrián, A P. Santos

The cylinder test allows us to determine the expansion of a copper cylinder by the detonation of an explosive charge inside. This test, originally designed for military explosives, has been adapted for industrial explosives with non-ideal behaviour. From data obtained with this test and known physical relationships, an analytical procedure has been developed to calculate the Jones-Wilkins-Lee (JWL) equation of state parameters for five ammonium nitrate/fuel oil (ANFO) and six emulsion-type explosives. A new radial wall expansion function is proposed considering a non-zero initial velocity with the consequent positive Gurney energy at unit relative volume. A set of equations is established to determine the JWL parameters, three of them obtained at the Chapman-Jouguet (CJ) point and the other three at different relative volumes. These equations, along with some constraints to ensure a physically sound solution, are solved for the JWL parameters by a non-linear least squares scheme. A 2D Lagrangian axisymmetric finite elements (FE) numerical model is developed for each tested explosive to validate the analytical results, in terms of expansion histories, with good agreement. This confirms that the set of conditions, constraints on the parameters and least squares calculation used constitute a robust methodology that fully captures the physics of the detonation products expansion involved in the cylinder test.CITATION:Castedo, R, Sanchidrián, J A, López, L M, Segarra, P and Santos, A P, 2015. Jones-Wilkins-Lee parameters for civil explosives, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 57–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Leppinen, B Johanson, R Kalapudas, G McMahon

The Suurikuusikko gold deposit was discovered in 1987 in western Finnish Lapland, 54 km NNE from the town centre of KittilS in the volcanic belt of Central Lapland. It is hosted by tholeiitic basalts in a graphite-bearing albitite breccia. The ore is located in subvertical shear zones characterised by strong albitisation, carbonatisation and sulfidisation. The ore minerals consist of arsenopyrite, pyrite, chalcopyrite, sphalerite, tetrahedrite, bournonite and rutile. Small amounts of pyrrhotite, gersdorffite, jamesonite, bornite, gudmundite, tetrahedrite, stibnite, kermesite, berthierite and native Sb are also present. Gold occurs as invisible and as 1 - 2 ¦m size inclusions in arsenopyrite and pyrite, on their grain boundaries and in fractures. The average amount of gold leached by cyanide is 2.93 per cent. The æinvisibleÆ gold contents were studied in pyrite and arsenopyrite by electron microprobe analysis (EPMA) and secondary ion mass spectrometry (SIMS) at CANMET/ MTL. Gold element distribution images show zoned patterns both in pyrite and arsenopyrite. SIMS analyses range from 343 to 55 ppm Au in arsenopyrite and from 217 ppm down to 0.32 ppm (detection limit 478 ppb) Au in pyrite. EPMA results range from 939 to below the detection limit 24 ppm Au in arsenopyrite and from 267 ppm to below 22 ppm Au in pyrite. Recovery of the refractory gold ore was studied using grinding, flotation, bio-oxidation and cyanidation tests. A sulfide bulk concentrate containing 40 ppm Au was obtained by flotation at 90 per cent recovery (As content 5.5 per cent, S content 22 per cent, and mass recovery 15 per cent). The grinding fineness in flotation was P80 -100 to 120 ¦m. At the original fineness the cyanidation recovery from the concentrate was lower than ten per cent, after ultra-fine grinding P80 -10 to 2 ¦m the Au recovery was less than 17 per cent. After bio- oxidation, Au recovery of 95 per cent was obtained in carbon-in-leach (CIL). The bio-oxidation time was two weeks in laboratory test, but after regrinding the oxidation rate was faster and recovery of Au higher. However, the selected method for the mining to be started in summer 2008 is open pit mining and mineral processing methods sulfide flotation and pressure oxidation in an autoclave. The ore reserves were estimated 31 December 2007 as: Probable 18.2 Mt with 5.1 g/t Au, Indicated 5.4 Mt with 3.0 g/t Au and Inferred 10.8 Mt with 3.4 g/t Au. The production capacity will be 3000 t/day.

Jan 1, 2008

By M Xu and, P F. Wells, A N. Kerr, Y Shields

Triethylene tetramine (TETA) has been used in combination with sodium sulfite (sulfite) for pyrrhotite depression at Clarabelle Mill since 1998. This combination has been highly successful at reducing pyrrhotite levels in the bulk (Ni/Cu) concentrate. Although highly effective, the roles of TETA and sulfite are not well understood. Treating bulk samples of the circuit feeds through the miniplant enabled the effects of circuit configuration on the performance of the pyrrhotite rejection circuits at Clarabelle to be determined. Reasons for the different performance of the non-magnetic pyrrhotite rejection circuit in the miniplant were investigated and tested in the laboratory. The effect of different grinding environments in the laboratory was examined to better understand the depressing mechanisms of TETA/sulfite. Modification of the grinding chemistry improved the selectivity of pentlandite over pyrrhotite in the presence of TETA/sulfite at current plant dosages.

Jan 1, 2005

By E R. Ramanaidou, C Tessarolo, M Verrall

Garnierite mineralogy in saprolitic ore of the Goro lateritic nickel deposit, New Caledonia , was investigated using X-ray diffraction (XRD), optical and scanning electron microscopy (SEM) and electron microprobe (EMP) analyses. These conspicuously, green-coloured phases occur either as submillimetre to centimetresized veins or as æbookletsÆ arranged in, macroscopic (subcentimetre sized), accordionlike structures supported in an undifferentiated matrix of mixed ÿ7+ and ÿ10+ phases. Within the veins, nickel for Mg solid solution increased from ten wt per cent NiO at the edge to 34 wt per cent NiO at the core, with vein edges comprising Ni-kerolite with <1.5 Ni per formula unit (pfu) grading to pimelite containing >1.5 Ni pfu at vein cores. The æbookletsÆ comprised nTpouite of formula, (Mg0.67Ni1.59Fe3+0.05)(Si2.17Al0.22)O5(OH)4 and averaged 30 per cent NiO. SEM element mapping highlighted the distribution and mineralogical association of Ni and Mg and emphasised the inverse relationship between Ni and Mg at the macroscopic (thin-section) scale. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By M Zoorabadi, B Hebblewhite, S Saydam, W Timms

Based on the cubic law, the hydraulic aperture of rock discontinuities has the most significant effect on the hydraulic conductivity of jointed rocks. The hydraulic aperture of rock discontinuities is a stress-dependant parameter and reduces with increasing applied stress. Furthermore, the rock stress increases with increasing depth. Therefore, hydraulic aperture is a depth-dependant parameter. In this paper, new empirical equations are introduced to calculate the hydraulic aperture of rock discontinuities at different depths. These equations were developed on the basis of back analysis of compiled packer tests from different actual cases. They provide the capability to calculate range of variation and average hydraulic aperture when the orientation of discontinuity and field stress tensor are given. Furthermore, it is possible to calculate the hydraulic aperture of rock discontinuities when its value is given for another depth. A hydraulic aperture of 7.7?µm was calculated by this method, comparing well with a reported site value of 8.3?µm for rock discontinuities at the Stripa mine project at a depth of 385?m. These new equations can be used by analytical or numerical methods to estimate the hydraulic conductivity of jointed rocks.CITATION:Zoorabadi, M, Saydam, S, Timms, W and Hebblewhite, B, 2014. New empirical equations to estimate the hydraulic aperture of rock discontinuities at different depths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 375–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By G Chen

Magnesite and dolomite are two salt-type minerals. The surface characteristics of these two minerals are almost the same. It is very difficult to remove dolomite from magnesite ores by flotation process. The present study was performed to develop a new collector and a better flotation scheme for magnesite from dolomite. The flotation tests show that there exists a significant difference in flotability between magnesite and dolomite when dodecyl phosphate synthesised with dodecanol, phosphorus oxychloride and other chemicals is used as collector. Sodium silicate was used as the modifier to improve flotation selectivity. It was found that sodium silicate selectively depressed magnesite at pH 4.5 - 7.5. The separation of magnesite from dolomite was achieved in a reverse flotation which resulted in a 76.1 per cent yield of magnesite with a grade of 47.3 per cent at 100 ppm dodecyl phosphate and 75 ppm sodium silicate. The flotation mechanism was investigated by characterising surface electrical properties and measuring the adsorption density of the reagents on magnesite and dolomite.

Jan 1, 2005

By McDougall I, Claoue-Long J

A combination of high precision 40Ar/39Ar and U-Pb dating has been used to determine the age of hydrothermal minerals and host rocks in a number of Lachlan Fold Belt (LFB) gold deposits in New South Wales, Au4 ralii In particular, this investigation demonstrates that the UAr/ Ar technique of K-Ar dating can be used to determine the timing of mineralization in Palaeozoic systems.A close temporal link between mineralization and Late Ordovician to Early Silurian magmatism is indicated by the dating work. Hydrothermal sericite from the Goonumbla p8rph gy Cu deposit and Glendale Au prospect yieldsAt/ Ar step heating ages between 437.9 ¦ 1.1 and 441.2 ¦ 1.1 Ma (16), and4 minjrnum age of about 425 Ma has been obtained by Ar/ Ar dating of hydrothermal amphibole from the Browns Creek Au-Cu skarn deposit. Hydrothermal aluniI8 frog the Gidginbung epithermal Au deposit yields reset 44 Ar/ Ar ages of 401.0 ¦ 1.3 to 417.3 ¦ 1.3 Ma (16). U-Pb dating by ion microprobe on magmatic zircons from the vicinity of the Goonumbla and Gidginbung deposits gives ages of 438 ¦ 3.5 Ma (2 6), and 435 ¦ 2.5 Ma (2 (7) respectimly, W a minimum age of 435 Ma has been obtained by Ar/ Ar dating of magmatic phases from volcanic rocks adjacent to the Browns Creek skarn deposit. Magmatic episodes near the Sheahan-Grants gold skarnpost give ages of 479.2 ¦ 1.1 and 467.9 ¦ 4o1 by 'Ar/ 9Ar dating of magmatic amphibole. Most Ar/3yAr age spectra show the effects of partial Ar loss at between 360-420 Ma, probably due to heating caused by granitoid emplacement.The radiometric dating work in this paper suggests a restricted metallogenic epoch in the Late Ordovician-Early Silurian LFB, NSW, of similar duration to that found in the Andean margin and the western Pacific island arcs around the Pacific Rini.

Jan 1, 1990

By S Basu, S L. A Gowravaram

CaF2 has been a common constituent in a wide variety of welding fluxes, including those used for submerged arc welding (SAW). The widespread use of CaF2 stems from its role in lowering the liquidus temperature as well as the viscosity of the molten slag that covers the weld pool. However, the harmful effect of fluoride evaporation from molten flux, on the environment as well as the health of the users is becoming increasingly evident over the years. This has led to increasing attention towards reducing the CaF2 concentration in the fluxes. The fluoride-free formulations face the challenging requirement to maintain the thermo-physical properties (viscosity, liquidus temperature etc) like those observed in fluoride-containing fluxes. In the present work, three fluxes with compositions in the CaO-MnO-SiO2-Al2O3 system have been identified as promising alternatives to the CaF2-rich fluxes. However, the thermo-physical properties of any such flux need to be comparable to CaF2-based commercial SAW fluxes before it can be adopted for regular use. The single hot thermocouple technique (SHTT) has been used by several researchers in the past as a tool for observing the melting and solidification characteristics of fluxes. This device has been developed in the present work and is used to characterise the melting behaviour of the fluxes. The measured solidus and liquidus temperatures from SHTT were compared with the results from differential thermal analysis (DTA) and simulations using the FactSage™ software for a comprehensive understanding. In spite of having a slight deviation in the measured values from the multiple techniques, the results obtained from these multiple methods show that the selected compositions could be potential CaF2 free alternative welding fluxes.

Jun 19, 2024

By A K. Ghosh, J Chung, E Topal, M Asad

"Many open pit (OP) mines with considerable vertical extent are approaching the end of their life-of-mine; some of them are seeking the opportunity to make the transition from OP to underground (UG) mining. The decision on the best location for transition from OP to UG mining should be addressed at the strategic mine planning stage. Conservatively, the transition to UG mining is considered near or after the exhaustion of the reserve within the ultimate pit.However, if UG is evident and exclusively viable from the inception, defining the best location for the transition through a conservative approach may not be an optimal option to explore. This clearly establishes the need for a mathematical model that aims to maximise the project value and considers OP and UG mining with crown pillar (CP) requirement simultaneously. Underground mine layout varies from one UG mining method to the other, and consequently the variation in the location of transition is eminent. Thus, focus on the selection of UG mining method must be a part of this analysisThis paper presents an implementation of an integer programming (IP) based mathematical model that evaluates the changes in mining layout and the project value under possible variation in the transition point from OP to UG mining for stoping and block caving methods. An IP problem is a mathematical optimisation or feasibility method in which some or all of the variables are restricted to be integers. The outcome of the implementation reflects that mining strategies with OP transition to stoping and block caving methods generated higher values than OP-only mining strategy. The case study not only demonstrates the difference in mining layout for both stoping method and block caving method, but also reflects that a joint consideration of OP mining, UG mining and CP placement helps to achieve maximum project value and resource utilisation.Citation:Darbritz, J, 2016. Remediation of Wall Failure at Kalgoorlie Consolidated Gold Mines' Golden Pike Cut-back 2016, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 96–103 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

Some attempt to minimise the importance of the greenhouse phenomenon. They do so by observing that global temperatures are still within the range of recent variations and that it is still not possible to predict with any certainty what the precise consequences of greenhouse will be. Both observations are true though the conclusion is dangerous. Ice core samples from the Antarctic and Greenland have established the composition of the atmosphere and global temperature over almost the last 200,000 years. The profile of these twin variables shows that they have moved together; when the concentration of CO2 has been up, the temperature has been up and when the former has been down the temperature has also been down. Over almost 200,000 years the CO2 content has ranged between lows of 190 ppm and highs of 270ppm. In just 200 years of industrialisation the CO2 content of the atmosphere has increased to 350 ppm, 50% higher that the mean of the last 200,000 years and 30% higher than at the start of the industrial age. Carbon dioxide is now increasing at 0.5% p.a. Methane, about twenty times more effective than CO2 as a greenhouse gas has doubled in concentration in the last two centuries and is now increasing at about 1.1% p.a. Methane, nitrous oxide, chlorofluorocarbons together with a number of lesser gases will double the greenhouse effect due to in creased CO2 over the next 40-50 years.

Jan 1, 1989

During the period 1981 - 1991, Esso Australia and their Joint Venture partners have discovered about 180 MB of liquids (crude and condensate), 60 MB natural gas liquids and 800 - 1000 GCF of gas. A total of 48 wildcat wells were drilled including 12 new pool discoveries drilled from platform facilities. Significant discoveries include the West Tuna, Kipper, Blackback and Terakihi fields. These four discoveries, contribute to 75 per cent of the total reserves discovered in the last decade and were all high-risk plays. The Kipper discovery, in the pre-Latrobe Golden Beach Group top sealed by volcanics, and the Blackback-Terakihi discoveries, located on the present day continental slope in water depths ranging from 300-700 metres are both the result of successful drilling outside the traditional exploration bounds for the basin. During the last decade, Esso and its partners have spent about A$400M on wildcat exploration activity. The exploration success rate, excluding platform based drilling, has been 50 per cent for wildcat wells. On a technical front, the last decade has heralded substantial improvements in seismic data quality. Peak frequency content in seismic data at the Latrobe Group target levels is now double that of the early 1980s. Significant advances have also been made in our understanding of sequence stratigraphy, geochemistry and geohistory of the basin.

Jan 1, 1992

By K Myers

Since the mid-1990s, the Chino Mine Facility (Chino) located near Silver City, New Mexico has been developing a closure plan with financial assurance to protect water quality, as required by State regulations. In February 2002, Chino and the New Mexico Environment Department (NMED) reached agreement on a closure plan; a closure cost amount of approximately $US 394 million ($A 591 million) was finalised in April 2003. Both the New Mexico Water Quality Act Regulations (1977) and the New Mexico Mining Act Regulations (1993) guided development of the closure plan and financial assurance amount. The process incorporated many years of correspondence, studies, negotiations and administrative hearings. The major technical issues focused on regrading slopes of the leach ore stockpiles and waste rock piles; cover systems; water treatment systems; and abatement of ground water contamination. The proposed financial assurance amount covers all closure costs and provides for perpetual water treatment.

Jan 1, 2003

The silver-lead ores of Yerranderie occur in a series of narrow, flat-dipping lodes in small bodies of quartz porphyry, intrusive into Upper Devonian volcanics, which are exposed in the western flank of the Permo-Triassic Basin of central New South Wales, about 80 miles south-west of Sydney (Harper, 1930; Lawrence, 1953). The lodes strike about E.-W. and are from 1,200ft. to 2,000ft. long. They consist of a series of ore shoots from 3ft. to 100ft. long, and up to 5ft. thick, though commonly under 2ft. thick, interspaced with low grade sections. They dip at from 18°S. to 400 S., and have persisted down the dip for 1,450ft. (693ft. vertical depth) in the Wollondilly mine, for 1,120ft. in the Bartlett's mine, and for 850ft. in the Wonga mine.The grade of ore in the Bartlett's mine was from 32% to 40% lead, from 100 oz. to 130 oz. silver per ton, 0.5 to 4.0% arsenic, with ore ,as rich as 20% arsenic on the No. 6 and No. 7 levels of the Silver Peak mine, the underlay extension of the Bartlett's lode, about 1% copper, and up to 4 dwt. gold per ton. In the Wollondilly mine the average grade was 15% lead, with sections as rich" as 36% lead, from 75 to 165 oz. silver per ton, 0.6 to 3.3% arsenic, 0.2 to 0.7% antimony, 0.8% copper, and up to 7...5. Cl~t. gold per ton. The zinc content of the ores is slight, and has not been recorded.Mining began about 1898, and to date more than 110,000 tons of ore, valued at £1,800,000, has been raised. Large scale mining ceased about 1935. The chief mines operating were the Bartlett's mine (formerly Colon Peak), the Silver Peaks, which is the underlay extension of the Bartlett's, the Wollondilly (or Yerranderie) mine, and the Wonga' (or Tonalli) mine.

Jan 1, 1953

By B P. Wrench, N R. Steward, C Wu

A gold mine in southern China has transitioned from an open pit operation to a fully underground mine. An overhand mining method is used which requires the mined stopes to be filled with backfill having an unconfined compressive strength of at least 0.35MPa. Tailings from the process plant is deposited into separate flotation and Carbon in Leach (CIL) tailings storage facilities. The tailings has a high fines content and the thickener on site could only produce a dilute flotation tailings at a solids content of about 30 wt%. This resulted in two undesirable outcomes: the density of flotation tailings in the Tailings Storage Facility (TSF) was significantly lower than planned so that the TSF could not store the life of mine tailings and that the backfill product had to include a high percentage of manufactured aggregate and increased cement content to achieve the required strength. This paper presents results of a tailings study which identified that the flotation TSF would be capable of storing the remaining life of mine tailings if an amended backfill product made up of 100% of flotation tailings could be introduced. A 100% tailings backfill with the addition of 8% cement was developed by classifying the tailings and using the coarser fraction in the backfill. This backfill allowed 60% of the flotation tailings to be placed underground and only the remaining 40% in the flotation TSF. A new thickener was designed and installed to thicken the tailings and rheological testing of the tailings, using a closed loop pilot plant, provided parameters to upgrade the underground reticulation system to deliver cemented backfill to stopes throughout the mine and to deliver thickened tailings to the TSF. The revised design was implemented and has resulted in considerable cost savings. CITATION:Steward, N R, Wrench, B P and Wu, C, 2018. Optimisation of surface tailings storage and tailings backfill – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 454–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Z Chang, S A. Mrozek, S Windle

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. It is important to understand skarn-porphyry transitions in order to use exposed skarns to look for associated and potentially larger porphyries. For such purposes, a good start is to understand the transition between porphyry and skarn in known deposits. In this contribution, we report the transition at Antamina, Peru, where skarns occur in and around a Miocene complex comprised of more than seven porphyritic intrusions. There are three types of skarn-porphyry relationships. The earliest intrusive phase, P1A, contains both endoskarn and porphyry-style quartz veins with secondary biotite halos. The porphyry quartz veins and endoskarns formed at the same time. Locally, the intrusion contains only endoskarn without porphyry quartz veins and is surrounded by exoskarns in carbonate wall rocks. In the third scenario, later porphyry (P2) intruding into P1A porphyry and skarns related to P1A contains abundant granular quartz veins and secondary biotite alteration but does not have significant endoskarn. The granular quartz veins also extend into earlier P1A skarns. The scarcity of endoskarn associated with P2 is related to the supply of Ca. The earliest P1A intrusion intruded into carbonates that supplied abundant Ca, therefore both endoskarns and exoskarns formed. In contrast, where the wall rocks of the later P2 intrusion are P1A or skarn related to P1A, there was little free Ca, therefore only porphyry-style quartz veins formed.CITATION:Chang, Z, Mrozek, S A, Meinert, L D and Windle, S, 2015. Skarn-porphyry transition – an example from the Antamina skarn, Peru, in Proceedings PACRIM 2015 Congress, pp 409–414 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By I Gipps

The mining industry has come through a period of major change in community expectations regarding safety and environmental impact and these changes can be expected to continue in the future. These changes are ultimately reflected in Government regulations and industry safety standards and form the basis of the ælicense to operateÆ. Equally, advances in technology have made possible new equipment and processes either available now, or close to completion, that will allow mines to meet these more stringent expectations if properly introduced. Changes in technology provide opportunities for mine management to introduce new systems that will remove people from hazardous areas and lead to improvements in the ætriple bottom lineÆ. In a longer time frame of five to ten years, novel and advanced technologies that are currently being developed will deliver new mining methods and conversion of presently uneconomic resources to ore. This is consistent with the time frame required to develop a new mine from discovery. Strategic decisions can be taken now by mine designers to enable the introduction of these major technology changes. Examples of both practical and strategic opportunities are drawn from the integration of rock cutting/blasting, automation, electronic communications and new mining methods. This paper discusses emerging industry trends, changes to legislative framework and some practical choices for existing and imminent technology.

Jan 1, 2003

By T McConachy

New opportunities for miners are beginning to appear through new discoveries, improved knowledge and access to vast unexplored areas of the deep sea and continental shelf. Recent discoveries of undersea hydrothermal deposits show evidence of high-grade mineralisation, although in many instances the extent of the resource is still unknown. The promise and the difficulties of undersea mining have been evident since attempts were first made to mine manganese nodules in the 1960s. The physical nature of the undersea resource is a key influence on its mining potential; and environmental issues will also become increasingly important. This paper explores these issues and concludes with a description of the immediate to medium term applied research required to develop this industry and the spin off that such research can provide.

Jan 1, 2000

The lignites of Otago and Southland offer a potentially viable future feedstock for electricity production and possible conversion to petrochemicals or liquid fuels. The deposits, when combined, represent New ZealandÆs largest energy inventory; equivalent to about 74 000 petajoules û or approximately 35 times current natural gas reserves. Too often dismissed as irrelevant to New ZealandÆs energy future because of adverse perceptions of the value of low rank coals, the strategic value of this resource is in fact huge.   Investigations of the lignites extend back over more than 50 years (LFTB various, CRL Energy Ltd). Whilst it is not the intention of this paper to review this work, these investigations have confirmed the suitability of the resource as a feedstock for thermochemical conversion. Current estimates of South Island lignite mining costs are NZ$1.0 - 3.0/GJ (Natusch 2005), making these resources amongst the most competitively-priced energy sources available world-wide.   This value, however, will only be captured if we as a country begin to envisage a world-scale, long-life, integrated and multi-faceted development sized to supply world markets for chemicals or fuels. Recent CAE studies (Hooper and Riddolls, 2005) have emphasised the vital importance of ensuring that any exploitation of this resource maximises their value to New Zealand. The question that thus must be applied is how might large-scale utilisation of the resource fit with New ZealandÆs primary energy supply, and its potential for the export of high-value commodities.   From the broader perspective of New ZealandÆs total energy supply equation we need to examine other supply options beyond just the generation of electricity. We face in this country a situation wherein almost all our liquid fuels feedstock has to be imported with projections for an increasing dependence on imported oil. In addition NZ has a natural gas reserves-to-production ratio of less than ten years, and dwindling supply from local production. Without further natural gas discoveries, New Zealand has only a window of approximately five years before we will need to commit to imported LNG or some other thermal fuels option.   In other words, New Zealand is facing an uncertain future unless we can restore energy inventories to cover an adequate strategic reserve capacity as well as enable long-term investment in alternative sources. Within this context the South Island lignite resources are thus deserving of more attention. The extent of the resource is well known, its suitability for conversion reasonably assessed, and its magnitude such that there is little doubt that lignite conversion could adequately meet NZÆs future energy needs for many years out.   This paper reviews coal gasification technology, its application to lignite and the possibilities for future development of the lignite resources. It is argued that the strategic imperative for this country is to secure the lignite resources as a primary energy source for this country well into the latter half of this century.

Jan 1, 2005