Search Documents

By K Dudley, D Readett

The design of entrainment control processes in copper SX plants has been studied by use of models based on achievable plant performance. A number of alternatives have been assessed for their suitability in minimising the transfer of deleterious species from PLS into the electrolyte. The position of the wash (scrub) stage in the circuit, either before or after the loaded organic tank, has been the subject of considerable debate. The modelling shows that at ænormalÆ entrainment levels, the performance of the circuits are very similar. However at high entrainment levels the selection of the wash after the loaded organic storage has significantly lower transfer of contaminants. When considering the inclusion of a loaded organic coalescer the results of the modelling again show that the best circuit has the loaded organic storage/coalescer before the wash stage. The overall control of EW contaminants includes both a wash stage and an EW bleed flow. The total water use for these two flows is shown to go through an absolute minimum. The minimum flow rate is not greatly dependant on the total entrainment from the SX settlers. This can be a useful operating strategy if the quantity of high quality water for make up is limited by the capacity of the water treatment plant (eg RO). However the minimum cost option is to maximise the flow of water to the wash stage and minimise the EW bleed stream. The main driver for this is the cost of the cobalt sulphate contained in the electrolyte. Some results from the latest circuit modifications at the Nifty and Girilambone Copper Projects are presented to confirm the benefits of using both coalescing systems and a wash stage. The EW bleed has been reduced to a level that is less than the loss internally in the SX stage to stage entrainment. There has been an occasional need to add chloride to the EW to maintain sufficient concentration to act as a growth modifier.

Jan 1, 2002

By Yamada K, Abe H

Magnetic scanning type mass spectrometers have been given improved sensitivity with a large dynamic range and considerable resolution by the addition of a computer-controlled electric equipment. A mass spectrometer equipped with this newly developed electric system was applied to studies of the activities of liquid iron-silicon alloys and of liquid iron-phosphorus alloys at 1600¦C. The range of silicon concentration was 5.8at%-51.1 Si= at%, and values of ySi -3.1+0.15 and es 11.5 +1.5 were obtained. The concentration range of phosphorus was 1.3at%-5.7at% and a value of eP=7.3+0.1 was obtained.

Jan 1, 1980

Slide presentation at conference

Jan 1, 1996

By Lysnar R, Horswill M

Since the introduction of the pocket calculator, electronic measuring equipment, lasers and computers, the mine surveyor's approach to his work has changed. Where he once used steel bands he now uses infra-red, visible light or radio waves. The reading and storing of angles is done automatically and he now has to be familiar with the facilities that a computer can offer, instead of plotting and calculating manually. This highly sophisticated equipment is continually being upgraded, modified and fine tuned. This paper will attempt to highlight some of the equipment at present in use by the surveying profession and research currently being conducted by the WA School of Mines. The various options in EDM will be considered including the latest unit capable of measuring distance without the benefit of a reflector, thus enabling the surveyor to co-ordinate points that were previously thought inaccessible. The School is currently working on changes to the GAK1 Gyro Theodolite which may improve results and enable the operator to have more control and confidence in his observations. Areas under consideration are improved lighting, binocular viewing and interfacing the instrument to a stopwatch. In the last few years the computer is being used not only for surface pickups and control but also for underground work. We will highlight the underground options in this area and the software available.

Jan 1, 1987

By Haskard R. W

A method of raising has been developed at Cobar Mines Pty Ltd's CSA Mine which has achieved advance of up to 6 m in a single blast and raises are now developed which have averaged 4.2 m per blast. The method is a form of Long Hole Raising and is applicable to short raises of less than 50 m length. Blast holes are column charged and initiated sequentially with short delay detonators (millisecond). The equipment used to drill the raising blast holes consists of normal production drilling rigs and accessories and no other special equipment is required. The method has significant advantages in rates of performance and fits neatly into production drilling and blasting schedules. The method is also far safer than any non-mechanical or conventional means of Raising.

Jan 1, 1983

By M Yahyaei, P Knights, M S. Kizil, J Qu

Digital Twins (DTs) are transforming business operations across many industries through their accurate representations of physical entities enabled by IoT technologies.

Sep 1, 2024

By Nevolina VG, Zakharova IB

The results of a study on the flotation of baddeleyite and associate minerals are presented, together with effective flotation reagents. Detailed microcrystallomorphological analysis of the benefication products were made to find out the features of distribution of different baddeleyite generations between froth and chamber products. To reveal the dynamics of interaction of technological properties of minerals with their morphology and constitution, a method of onthogenetic analysis was used. It is well known that the difference between technological properties of the particles of the same mineral depend greatly on its genesis, but also the relation is direct - by means of constitution (habit). Thus, flotation behaviour of minerals depends on morphology microinclusions, distribution of impurities, dislocations and physical properties of individual particles. The microrelief of baddeleyite grains and crystals from froth and chamber products was studied with an electron scanning microscope. Chemical composition was determined by means of laser, microprobe and chemical analyses. The difference between baddeleyite generations, their distribution in benefication products, and the effects of grain sizes, number of inclusions and chemical compositions were valuated. Conclusions on baddeleyite flotation properties were made. Mineralogical study on eudialite grains from rough ore and eudialite concentrate was carried out. The interrelation between eudialite and associate minerals and negative effect of aegirine on technological properties of eudialite were revealed as well.

Jan 1, 1993

By Large RR

Underlying the 15 million tonne, high grade Hellyer volcanogenic massive sulphide deposit of western Tasmania is an extensive, well developed, and well preserved stringer system. Pervasive alteration of the footwall mafic volcanics occurred as the hydrothermal system initiated. Mineralogical zoning exists within the footwall alteration pipe, with a central siliceous core giving way to zones of chlorite, chlorite-carbonate, sericite-chlorite, and finally sericite-quartz on the margins (stringer envelope zone). However, the alteration morphology and zonation is not symmetrical around the central siliceous core; eastward the alteration zones are steeply dipping and terminate abruptly under the massive sulphide, while westward they extend out under the ore body in a blanket fashion. Geologic evidence indicates that the pervasive alteration started with the development of sericite-quartz which was subsequently overprinted by chlorite and finally quartz-sericite as the hydrothermal system became focused towards the centre of the stringer system.

Jan 1, 1990

Drilling has disclosed a sequence of Cainozoic sediments immediately to the west of the Ediacara mineral field containing little or no dolomitic debris in the lower and middle sections, but with gravel beds of dolomite derived from local rocks in the upper part. It is suggested that the lower and middle sequence of Cainozoic strata was deposited over the area of the Ediacara Range, and that this range was uplifted, probably as a horst block, during Quaternary times and was first exposed to subaerial erosion during the upper Pleistocene epoch.Lower Cambrian dolomites with associated stratiform lead mineralization, which formed the target of drilling on the western downthrown block of the Ediacara Fault, were eroded before deposition of Cainozoic sediments.Intense leaching of basal Cambrian dolomites around the periphery of the Ediacara Basin took place during Mesozoic and Tertiary times. This leaching process has resulted in enrichment of copper and lead mineralization in a thick marginal zone of residual clayey material overlain by dolomitic collapse breccia. These zones of leaching and enrichment were preserved under Cainozoic sediments which have subsequently been eroded. The Ediacara Fault appears to have been a major conduit for mineralizing fluids and is the main lineament of the Torrens Hinge Zone. Contemporaneous movements on this fault have controlled rates of depositionand thickness of sediments across the fault during Adelaidean and Cainozoic times. Though latest movements of this fault have been west block down, the predominant movement has been east block down with associated thickening of sediments to the east in the Adelaide Geosync1ine.

Jan 1, 1972

By A Roseman, T Gruber

Traditional methods for installing gaskets for segmented bored tunnels have relied upon different bonding procedures with adhesives that carry a series of disadvantages to segment producers. Fixation of the gaskets into the concrete segment as part of the casting procedure has been developed over the last 20 years and has emerged as an economical solution to produce high-quality tunnel segments for various technical tunnel applications. This paper investigates the advantages of using anchored gaskets, the different tunnel systems that employ anchor gaskets and reviews the first anchor gasket project; the Lee Tunnel and analyses how segment production efficiencies are gained.CITATION:Gruber, T and Roseman, A, 2014. Use of anchored gaskets in segmented bored tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 253–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By T A. Helms, P Gottlieb, S E, R Bateman

In response to the ever-increasing challenges facing the modern gold mining industry and the need for improved gold recoveries within all processing streams, CSIRO has upgraded its latest automated mineralogical analysis system, QemSCAN (formerly QEM*SEM), with special purpose hardware that speeds up the location and measurement of precious metal-bearing phases. By rapidly scanning the surface of polished blocks, and accepting only fields that contain the minerals of interest, QemSCAN is able to find, map, and quantify target minerals in extreme detail. Phase identification and quantification is achieved by placing a grid of points over the target particle and collecting X-ray information at each analysis point. The resulting mineral maps provide the metallurgist with a complete textural description of all gold-bearing phases within the product measured, together with quantification of the gold phases in terms of their modal abundance, particle size, mineral associations, relative contributions to gold deportment and liberation characteristics. Examples are presented which illustrate how QemSCAN is able to find and quantify gold-bearing phases within low-grade ores from the Super Pit, Kalgoorlie. This work is the result of a collaborative project between Kalgoorlie Consolidated Gold Mines (KCGM), CSIRO Minerals, and the University of Queensland, and is on-going.

Jan 1, 2000

By Leung L, Downey M

This paper presents an overview of a technology package developed by BHP for locating discontinuities in coal seams using an in-seam seismic (ISS) exploration technique. The technology package includes instrumentation, data processing software, field procedures, numerical modelling and interpretation know-how. The technology developed has proved to be highly successful; features such as faults and dykes, not detected by other methods, have been delineated. Using equipment specifically designed for underground use, surveys are carried out quickly and at low cost. More than 30 ISS surveys have been conducted by BHP in Australia. Substantial savings in production revenue have been realised in situations where ISS has identified mining conditions which would have impeded longwall operations. Case studies of several ISS surveys are described in the Paper.

Jan 1, 1987

By G Byrne

Long-term water management is typically ignored in mine closure planning. A review of 73 mine closure plans dating from 2007 to 2013 shows that, on average, relinquishment is proposed to be achieved in 11 years. A separate review of 57 mines in actual closure shows that only five have so far achieved relinquishment with an average closure period of 14 years after production cessation. The remaining 91 per cent of sites in closure have an average closure duration to date of 21 years - and still going.A common issue among those sites in closure is water management, with a further common issue being acid and metaliferous drainage (AMD). Of the closure plans that were reviewed only one site had allowance for long-term (>50 years) of water treatment. Of the sites in actual closure 25 per cent have reported that they expect such long-term water treatment, with many acknowledging that in perpetuity treatment is probable.Clearly there is a gap between what is being allowed in closure plans and the reality of closure. There are a number of factors leading to the optimism of the closure plans, including unrealistic assumptions, pressures to reduce closure cost provisions and the technical complexity of many AMD issues.Long-term water management is a reality that needs to be acknowledged and addressed. If addressed early in the mine life cycle the impacts for mining companies can be reduced.CITATION:Byrne, G, 2013. Long-term water management - the forgotten legacy of mine closure, in Proceedings Water in Mining 2013 , pp 163-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By T Baumgartl, B Richards

Covers on waste rock and tailings remain the primary choice for closure planning where the purpose is to create an environment where water ingress into reactive material can be controlled and/or prevented. In semi-arid and arid environments, dry cover systems are the preferred option with the design intention to absorb rainfall and to prevent deep drainage. Although the average amount of rain typical for semi-arid environments is relatively low and evaporative demand is high, the seasonal and annual distribution may vary greatly. Rocky substrates are often the only choice for the construction of covers due to economic constraints or availability of suitable materials. While the water holding capacity may be suitable for the application of a dry cover design in arid and semi-arid climates, some of these covers bear the risk of preferential water flow when rain events are intensive or occurring at high frequency. The objective of this presentation is to demonstrate the occurrence of preferential flow through rock containing dry cover systems. A regional classification for the applicability of dry covers is attempted to delineate those regions of Australia where the characteristic of the rainfall pattern increases the risk of failure for dry cover designs. CITATION:Baumgartl, T and Richards, B, 2016. Rainfall patterns rather than climate classification control cover design for closure, in Proceedings Life-of-Mine 2016 Conference, pp 89–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Windsor C

A review of the current pit design procedures and their performance has been undertaken recently by Mining Research Associates (MRA) and the CSIRO Division of Geomechanics. Visits were made to mines covering a wide range of operations. A questionnaire was completed by each mine in order to collate the relevant information. Interviews were also made with representatives of the Mines Departments to ascertain their role in regulating mine designs. Design expectations were compared with field performance, and reasons for variations noted. Problems associated with designs were identified and suggested methods of alleviating the problems have been made.

Jan 1, 1986

By T D. H McGrath, O Baker, W P. Staunton, C Ypelaan

"The carbon-in-pulp process has been used extensively in the gold industry since the late 1970s to recovery leached gold from solution. Despite more than 30 years of experience in operating carbon circuits, average gold solution loss has remained at an average of 0.02–0.03 ppm (mg/L), higher than the ‘best practice’ target of 0.01 ppm.Process modelling, such as SIMCIL developed by the Curtin Gold Technology Group (GTG), can provide information on optimum set points; however, manual control of the circuit limits the potential benefits.An automated carbon measurement device, the Scout Carbon Meter, has been developed to allow for automation of carbon concentration measurement, and automated control of the carbon transfer pumps. This paper describes the results from the evaluation of the first two prototypes of the meter.Citation:Staunton, W P, McGrath, T D H, Ypelaan, C, Baker, O and Eksteen, J J, 2016. Optimising Carbon Management - Increasing Gold Recovery and Decreasing Costs with the Carbon Scout, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 225–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Pollard DM, Willis GM

The removal of bismuth from liquid copper in a vacuum furnace was studied over a range of pressures. The rate determining step changes from diffusion in the gas at pressures above 0.2 Torr to approach the Langmuir evaporation rate at pressures of 10-2 Torr. Oxygen and sulphur were found to have a negligible effect on the rate. Bismuth removal from copper sulphide was found to be considerably slower than from copper. This is consistent with the known thermodynamic properties of ternary sulphide melts.

Jan 1, 1980

By Worner H. K

The paper briefly summarises the work of the Titanium Research Section in the Metallurgy Department of the University of Melbourne and mentions the development of a new electrolytic process for titanium production. This process utilises the "hot-spot" cathode technique and titanium carbide anodes. An introduction is given to three further papers on titanium metallurgy to be presented to the Institute.INTRODUCTIONThe unique combination of strength, lightness and corrosion resistance possessed :by titanium and its, alloy has made them of great interest to engineers. However, high cost, difficulties of production and limited knowledge of techniques of application restrict their usage at present almost exclusively to high priority armaments.The cost of the metal is divided between extraction and processing and much research has been carried out to devise new and cheaper methods for winning the metal from its ores. Processing costs will be reduced when production volume increases.Extraction research is proceeding rapidly overseas and Kellogg (1955, p. 72) reports that 'at least seventeen companies in the U.S.A. are interested in titanium production. Of these, two are producing the metal by a modified Kroll process, three are building Kroll plants and the remainder are in various stages of research activity. The Horizons Corporation alone is contemplating electrolytic extraction and is building a pilot plant. Steinberg et aI. (1955, p. 252, p. 332) have reported the early work done by the HorizonsCorporation on electrolysis of potassium fluotitanate and titanium monoxide in fused salt electrolytes. Of these two, the former appears to be the more attractive process.

Jan 1, 1956

By Kuwasaki N, Mitsune Y

Many activity measurements of components in liquid oxides have been reported in the field of slag chemistry. However, very little is known about the thermodynamic behavior of compo- nents in oxide solid solutions. In the present paper, e.m.fs. of the follow- ing galvanic cells employing solid electrolyte Zr02(CaO) were measured on the entire range of composition of the solid solutions. Pt/Ni-(Mgl-x ix)O/ZrO2(CaO)/Ni-NiO/Pt Pt/Ni-(Mgl-xNix)2SiO./ZrO2(CaO)/Ni-NiO/Pt Pt/Ni-(Mg l-xNix)Si03/ZrO2(CaO)/Ni-NiO/Pt. Activities of NiO in these solid solutions of (Mgl_ Nix)O and (Mgl_ Nix) 2Si0a(where 0

Jan 1, 1980

Australian continental crust has accreted and consolidated by thirds: 1/3 during Archean time, 1/3 during Early to mid-Proterozoic time, and 1/3 during latest Precambrian to mostly Paleozoic time. The progression of orogenic systems and the crustal consolidations they represent seem not fundamentally different in basic orogenic processes from better known Mesozoic-Cenozoic examples in that accretionary, continental margin, collisional, and intraplate intracratonic inverted and/or reactivated systems are all recognizable in the tectonic evolution ofAustralia.

Jan 1, 1995