Search Documents

By I. J. Demer, M. L. Holzworth, J. C. Kremer, P. A. Beck

For alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystal-lization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig I shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hr. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b It is seen that for any annealing temperature below T, the grain size was smaller than. in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T, the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig I by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has been most frequently and best investigated in brass. This type has been designated as "normal grain growth,'' while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1949

By M. R. Tek, K. H. Coats, D. L. Katz

In natural gas storage operations, seasonal pressure fluctuations in the gas reservoir cause the water from the surrounding aquifer to flow into and out of the gas sand. The theory of unsteady-state liquid flow through porous media developed by Van Everdingen and Hurst' has been applied to predict the water movement into and out of the gar bubble for .several .postulated pressure cycles. Those cycles with as many pound-days above the original aquifer pressure as pound-days below, may cause the gas reservoir to slowly grow or shrink rather than hold to a constant volume. Applications to an actual field case study give the predicted gas reservoir monthly pressures and volumes as compared with the observed monthly pressures and volumes. INTRODUCTION A large number of natural gas storage reservoirs are bounded by or adjacent to large water-saturated formations called aquifers. The presence of these aquifers is usually evidenced by the production of water from wells delineating the gas-hearing sands. Some gas storage reservoirs in use today have been purposely developed on aquifers. Cyclic pressure variations in a gas storage reservoir cause water influx and efflux from the surrounding aquifer. This, in turn, results in a varying gas reservoir volume. The prediction of the effect of this aquifer fluid movement on the size and size variation of the gas reservoir can provide information valuable in the study of several reservoir engineering problems. The economics of gas storage operations are directly influenced by the influx of aquifer fluid into the reservoir since a shrinking storage reservoir requires increasing pressures for the storage of the same quantity of gas. Material balance and reserve or recovery calculations also obviously require knowledge of reservoir volume. Various other reservoir engineering calculations such as interpretation of well interference data, evaluation of physical characteristics of porous media, water coning, gas injection and pressure maintenance studies are typical problems where variations of volume due to edge or bottom-water encroachment becomes important. The solution of equations describing influx and efflux of water in the gas sand, application to gas storage reservoir behavior and interpretation of results are the main objectives of this paper. While this work was directed toward gas storage reservoirs, it applies equally well to repressuring of partially depleted oil reservoirs with an active water drive. MATHEMATICAL ANALYSIS As just mentioned, the cyclic pressure variations in an aquifer-surrounded gas storage reservoir cause water movement and varying gas reservoir volume. Prediction of this volume variation from the reservoir pressure cycles or the injection-production schedule requires adoption of a flow model, certain assumptions concerning reservoir and fluid properties, and formulation and solution of the governing differential equation. The flow model used in this study is a gas bubble located on a very large aquifer (Fig. la). Gas bubble radius and aquifer sand thickness are denoted by rr and h, respectively. Fig. lb shows the horizontal, radial two-dimensional porous reservoir attended by the unsteady, compressible motion of the aquifer liquid. Volume variation of the gas bubble is determined from aquifer water flow across the cylindrical boundary, r = r0

By Blake M. Loring, Robert A. Colton

MELTING procedures for most metals and alloys usually include some provision for the control of oxygen, since this element frequently has some undesirable effect on the properties of the metal or alloy concerned. In the melting of the various bronzes, this is especially true, since oxygen can be introduced into the melt in a number of ways, most of which are difficult to control. In making bronzes from virgin materials, oxygen is usually present in the commercial grades of copper used; electrolytic he refined copper ingots usually contain from 0.02 to 0.05 per cent oxygen. When ingot metal or scrap bronze is used in the charge, oxides are almost always present to some degree. Under certain melting conditions and in certain types of melting equipment the atmosphere over the metal may be highly oxidizing. This, of course, may be desirable in the melting practice used, but is certain to introduce appreciable amounts of oxygen into the melt, and that may not be entirely desirable. From the foundry viewpoint oxygen may have several harmful effects on bronzes. The formation of excessive amounts of oxides may produce drossy metal, which, in turn, means dirty castings and a potentially high rejection rate. It is claimed, too, that oxides in the metal may combine with hydrogen to form steam and thereby produce porosity in certain of the bronzes. The presence of certain refractory oxides, such as SnO2, may be undesirable from the viewpoint of making machining difficult, or as possible stress-raisers in the metal matrix. It is often said that excessive oxide present in the liquid metal makes the metal run sluggishly. Since it appears impractical to try to control the amount of oxygen introduced into the metal beyond taking the economical limit of precaution about charging dirty scrap, it would seem that control of the oxygen content of the liquid metal offers the most promising approach to this problem. This might be done by using slags, or covers, or by the use of some element or compound added to the melt to remove oxygen preferentially. Most aspects of this problem have been considered and considerable work has been done along these lines. A reconsideration of the problem is indicated, however, by the controversial nature of the evidence at hand, especially on the possibility of using a chemical deoxidizer to control the oxygen content of bronzes. CHOICE OF DEOXIDIZER The choice of the chemical agent selected as a deoxidizer would naturally depend first on the alloy in which it is to be used; in this particular case the alloy is Navy gun metal. In Table I are listed a group of elements that might be considered as

Jan 1, 1946

By E. J. Duggan

THE mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. DESCRIPTION OF ORE The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chalcopyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the dose association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. HISTORY Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From 1926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and' 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for molybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill 10,000 tons per day, but it was not long before 12,500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. To increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. CRUSHING There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. 1) and No. 2, of 15,000 tons capacity (Fig. 2).

Jan 1, 1942

By H. S. Rankin, E. C. Houston

OLIVINE is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 per cent; Mn, 0.012 per cent; Ni, none. Chlorination[f] of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SUPPLY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.1 The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940. It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. PREVIOUS TECHNICAL WORK In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. Unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment5 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By J. O. Betterton, W. M. Spicer

The solubilities of antimony in the a and ß-forms of zirconium were determined between 750" and 1300°C. The a-phase forms by a peritectoid reaction, and the a/(a + ß) and ß/(a + ß) phase boundaries rise in temperature with in- ' creasing antimony. Impurities in the 99.95 pct zirconium were sufficient to influence the phase boundaries and the variation reported is approximate. The restricted solid solubility of the terminal zirconium phases, which is especially characteristic of this system, is thought to result from the low free energy of the Zr2Sb phase. ZIRCONIUM-antimony alloys are important in zirconium alloying studies since antimony is one of the highest valent elements which can be used to make zirconium alloys. The dilute alloys are of further interest as they have somewhat better corrosion resistance' than pure zirconium. The first investigation of the phase diagram was made by Russi and wilhelm2 who found a eutectic reaction, liquid (- 17.5 at. pct Sb) = ß zirconium (- 11 at. pct Sb) + Zr2Sb, at 1430°C'. The Zr2Sb phase was of complicated hexagonal structure, and by thermal analyses of the relatively impure alloys then available, Russi and Wilhelm found evidence for the peritectoid formation of the a-phase. EXPERIMENTAL In the present work, the phase diagram was re-investigated in the region 0 to 5 at. pct Sb and 750" to 1300°C using iodide-zirconium alloys. Details of the procedure have been described earlier. Essentially the alloys were prepared by arc casting and were then examined by the annealing and quenching method. The times of annealing varied from 1 hr at 1300°C to 30 days at 760°C. As in other zirconium phase-diagram studies1"5 the impurities in the zirconium were still sufficient to affect the results, and the experiments will therefore be described in 3 parts. The results from the first 2 parts of the work are shown in Fig. 1. Here the ß/(ß + Zr2Sb) and a/(a + ZrzSb) phase boundaries were determined with alloys made from 99.9 pct zirconium,* and cast under such conditions that the Vickers hardness of a alloys extrapolated to 95 to 110 VPN at 0 at. pct Sb. Such alloys were not suitable for investigations of the (a + ß) region, and the results shown in Fig. 1 near the (a+ ß) and (a +ß + Zr2Sb) regions were determined with purer alloys. These alloys had an extrapolated hardness range of 75 to 85 VPN and were made from 99.95 pct zirconium. A deviation from binary equilibrium occurs in Fig. 1 as indicated by the (a + ß) region of pure

Jan 1, 1959

By H. S. Rankin, E. C. Houston

OLIVINE is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 per cent; Mn, 0.012 per cent; Ni, none. Chlorinationt of olivine has two major defects: (I) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SUPPLY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.1 The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940. It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. PREVIOUS TECHNICAL WORK In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. Unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatments and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By E. C. Houston, H. S. Rankin

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By H. S. Rankin, E. C. Houston

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By D. Walton

The effect of small solute additions of Cu on the activation energies for creep A1 single crystals were determined over the range from 78° to 850° K. Below 240°K and above 800°K activation energies were unchanged. Between 240°K and 400°K strain aging causes the creep rate to become vanishingly small and the flow stress was independent of the temperature. Between 500° and 50°K the activation energy was increased to 41,000 cal per mole. NUMEROUS investigationsL have shown that solid solution alloying invariably increases the flow stress. A typical example is documented in Fig. 1. Such increases in flow stress can arise from two general effects: Alloying can increase the long-range stress fields through which dislocations must move by causing appropriate clustering; modification of dislocation densities, and so forth. Alloying can also modify the short-range stress fields that determine the activation energies for thermally stimulated migration of dislocations, such as occurs in some solute atom pinning processes, and so forth. Actually both long- and short-range stress-field effects can occur simultaneously. It was the purpose of this investigation to evaluate the effect of alloying on the short-range stress fields by determining the effect of alloying on the activation energies for creep. The resulting observations also shed some light on the effect of long-range stress fields on dislocation processes. EXPERIMENTAL TECHNIQUE Single-crystal bars (6 in. long 3/8 in. wide and l/4 in. thick) of dilute solutions of Cu in A1 were seeded, so as to provide extensive single slip, with the pole of the tensile axis located in the standard stereographic projection as shown in Fig. 2. Each crystal was grown under an argon atmosphere in a graphite mold containing a large reservoir of molten alloy for the purpose of obtaining rather uniform composition of Cu along the length of the bar. The nominal compositions of the alloys which were produced from 99.99 pct Cu and high-purity A1 containing 0.001 pct Fe and 0.001 pct Si, are given in Table I. Strains, measured by linear variable transformers attached by quartz rods to a 3 in. gage section were sensitive to and the stresses were ap- plied by direct loading of the specimen. Temperatures were determined by thermocouples attached to the gage section of the specimens. Below 400°K the apparent activation energies for creep, Q, were determined by the effect of small, rapid changes in temperature of about + 10°K from T1 to T2 on the corresponding creep rates ?1 and ?2 during primary creep according to where R is the gas constant.' Above 400°K, Q was evaluated from Eq. [1] for the secondary creep rate using temperature changes of about ±20K. A typical set of results is shown in Fig. 3. RESULTS AND DISCUSSION The previously obtained effect of temperature on the apparent activation energy for creep of single crystals of high-purity A12 is shown by the broken curve of Fig. 4. The datum points on the same graph illustrate the effect of dilute a solid solution alloying with Cu on the activation energy between 600" and 750°K. Each plotted point is the average of not less than five independent test values between 600° and 750°K and not less than three at other tempera-

Jan 1, 1962

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Early in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fickl and Ruer and Goerensz definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line of immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 157oOC in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Fords have shown that, when hot-rolled copper-iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have I50,000 psi tensile strength, and about 41 pct I.\CS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult. In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation of this type of alloy. As a result of this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1949

By H. B. Aaron

DIFFRACTION micrography provides a useful tool for studying complex strain fields. Newkirk1 observed an X-ray diffraction effect due to strain interactions at the intersection of slip lines in LiF and attributed this effect to a reduction of primary extinction due to strain-gradients. It is the object of the current study to correlate the observations and rationalize the appearance of the strain fields around intersecting slip planes in x-ray extinction contrast studies by a semiempirical method. Fig. 1 shows typical strain patterns observed by Newkirk on (200) reflections in LiF using chromium radiation and a variation of the Berg-Barrett (B-B) technique. In other reflections (e.g., {220}) the strain patterns are absent. If one defines a vector 3 along the striations from the more to the less dense portion, and a vector v in the direction of the X-ray beam parallel to the reflecting plane, such that both 3 and v lie in the reflecting plane of the crystal, Fig. 1, then the positions of the striations on (200) reflections appear to be confined such that where is the angle between v and 3, Fig. 1. It will be seen later that 3 is the projection of Sb on the reflecting planes. In some instances the strain effects are observed only above the slip plane, Fig. l(C), in others only below, Fig. l(D). Where the strains appear to be both above and below the slip line, Fig. l(E), one sees that there are actually two slip lines present, Fig. 1(F) and (G). Furthermore, the strain patterns are observed in the vicinity of the intersection of emergent edge dislocations (diagonal lines on the micrograph) with emergent screw dislocations (horizontal lines on the micrograph), e.g., Fig. l(HJ) and (MN), but not in the vicinity of the intersection of two emergent edge dislocation arrays, Fig. l(HJ) and (KL). However, in the latter case the contrast of the dislocation array itself is reduced along (KL) and increased along (HJ). Line (AB) in Fig. 1 is the edge of the crystal, and the material to the left of (AB) is the side of the sample. Any empirical correlation will have to include most, if not all of the aforementioned observations. Lang2 and Newkirk1 determined that the condition for contrast is given by g-b#0 [2] where b is the Burgers' vector and g the diffraction vector (normal to the reflecting planes). If one assumes that the direction of the observed strain fields is given by the vector sum of the slip vectors (Sb1) of the intersecting slip planes, then Eq. [2] may be generalized to g-S#0 [3]

Jan 1, 1963

By A. B. Stevens

IN the calculation of oil and gas reserves by volumetric methods, it is necessary to know the volume of the reservoir available for the storage of the oil or gas. To obtain this information, a number of methods for determining both total and effective porosity of reservoir rocks are used. For the determination of the total porosity, or the porosity that considers all of the pore spaces, connected and isolated, the Russell7,8,9 and the Melcher-Nutting1-6 methods are the best known and most- widely used in the petroleum industry. These methods have disadvantages in that they give the total porosity of the samples and in that the samples are reduced to grain size in the determination. In many sands there may be little or no difference between total and effective porosity but in other sands there may be considerable difference between the two. For the estimation of oil-and gas reserves the effective porosity of the reservoir rock always should be used. Of the methods that have been developed for the determination of the effective porosity of reservoir rocks, or the porosity that considers only those pore spaces that are connected, the best known are the so-called Boyle's law6,10-13, and the Washburn-Buntings.5,6,11 methods. The Wash-burn-Bunting method is probably the most widely used because it gives effective porosity, it is rapid, and the apparatus is inexpensive. This method employs a special porosimeter in which the core sample is placed in direct contact with mercury. This method has disadvantages in that, as a result of the high vacuum created in the pore spaces, mercury is drawn into the openings, making it impossible to use the sample for a check determination and also ruining the sample for any further test, such as permeability. The purpose of this paper is to describe an appa-ratus employing the same principle as the Washburn-Bunting method but so designed that the core sample does not come in contact with the mercury in the porosimeter.

Jan 1, 1939

By G. A. Bole, F. W. Davis

The purpose of this paper is not to report, to the Institute, the results so far obtained in the survey, by the Bureau of Mines, of the metallurgical requirements for open-hearth refractories, but to present an outline that we hope will serve as a basis for discussion. The systematic survey that the Bureau proposes to make has not been outlined, although considerable preliminary work has been done in the way of interviewing open-hearth superintendents in several of the larger steel plants from the Chicago district eastward. At the several conferences so many of the opinions were diametrically oppoeite, when considering the same point, that it was thought that such an opportunity as the Institute offers in the way of a clearing house for moot metallurgical topics should not be overlooked. For this reason, the paper has been prepared as a basis for a discussion which, it is believed, will be of value in outlining the program of the Bureau. D. A. LYoN, Assistant Director. The importance of securing suitable refractories for metallurgical operations is daily becoming more universally recognized; particularly in the manufacture of open-hearth steel, where the life and earning power of the furnace depends largely on the judgment and care exercised in the selection of the correct quality of refractory for each of the parts. Any innovation that would make available to the steel manufacturers refractories with longer life or better suited to their needs than those now employed, and at a cost that would permit of their use, would be of enormous value to the industry at large. It is quite probable that revolutionary changes would not be necessary. Material now used in some parts of the furnace might, by more suitable preparation, be made of much greater service; in other parts, possibly entirely different material would be necessary in order to effect much improvement. Inasmuch as different parts of the furnace structure perform different functions and are subjected to different service conditions, a refractory suitable for one part will be entirely unsuited for another. For this reason, to make a comprehensive study of the refractory requirements of the processes, we should consider the furnace as built up of a number

Jan 1, 1924

SECTION I PAGE PAGE Bulletins Wanted v Local Section News xv St. Louis Meeting v Affiliated Student Society Notes.. xviii National Engineering Societies in California's Mineral Resources National Service..: vii ? for War Purposes xix Members in Officers Reserve Corps xi Forthcoming Meetings xx Resolution by Military Engineering ? Library xxi Committee xi Membership. :: xxiv Personal :.. xii Biographical Notice of David H. Employment xiv Browne xliv Alaska Mining and Engineering Institute Committees xlvii Society xv Officers and Directors liv

Jan 6, 1917

NEW YORK MEETING PAGE Winchell, H. V.-Geology of Pachuca and El Oro, Mexico. Discussed by Frederick MacCoy, Robert Hawxhurst, Jr 2 WILKES-BARRE MEETING Kynor, Herbert D.-Mechanical Mining of Anthracite. Discussed by C. Evans, Jr., S. J. Jennings, W. J. Richards, Geo. S. Rice, and the author 3 Stein, C. H.-Ashley Planes for Handling Freight Traffic. Discussed by Graham Bright, Douglas Bunting, S. J. Jennings, R. V. Norris, C. H. Strange, Edwin Ludlow, W. J. Richards, and the author 3 Markle, Donald.-Anthracoal: A New Domestic and Metallurgical Fuel. Discussed by William Griffith, Edwin Ludlow, E. M. Chance, Charles Dorrance, E. W. Parker, G. H. Ashley, C. A. Burdick, Geo. S. Rice, and the author :.. 7 Griffen, John.-Slush Problem in Anthracite Preparation. Discussed by Henry Flood, Jr 11 Eavenson, H. N.-Lynch Plant of United States Coal and Coke Co. Discussed by E. V. d'Invilliers, C. Evans, Jr., Graham Bright, Geo. S. Rice, Geo. Otis Smith, A. M. Rodgers, C. T. Starr, C. A. Burdick, and the author 15 Bunting, Douglas.-Mine Fires Extinguished by Sealing. Discussed by Geo. S. Rice, J. B. Warriner, H. H. Otto, Edwin Ludlow, E. M. Chance, F. B. Nold, H. M. Chance, W. L. Jacobus, J. A. S. Ritson, R. D. Hall, Geo. S. Rice, and the author 18 Bright, Graham.-Determination of Electrical Equipment for a Mine Hoist. Discussed by F. L. Stone, Geo. S. Rice, L. F. Mitten, and the author 34

Jan 12, 1921

By A. K. Knickerbocker

Practically all underground work on the Minnesota iron ranges is done by miners working on a so-called contract wage system. This system, while it has certain advantages over the straight day's pay or company-account method of wage payment, has serious and vital defects. In view of the scarcity and demands of labor, it is important that employers of labor scrutinize their systems of wage payments carefully, not only to save losses and trouble, due to labor disturbances, but also to secure the greatest efficiency of their workmen and reduce their operating costs. It is admitted that an adequate, just, and equitable wage is the prime factor in bringing about these benefits. The wage of labor and its method of application and payment have been, and always will be, the main factors in the unrest and dissatis. faction of labor. Not only does labor want and need an adequate wage, assuming that work is adequately performed, but it wants and is entitled to a just and equitable wage. Labor must have respect for the fairness of the wage and for the fairness of the management in the application of the wage It is conceded that the Minnesota iron miners are now, and have been, in the main paid adequately, but the inherent defects of the so-called contract system prevent any just or equitable application of this wage to the various units of the labor body. The defects of the contract system, with its obvious inequalities, favoritisms, and injustices, are cancers in the brain of labor. Every thinking miner realizes these defects and knows just what they are; the unthinking do not realize the details of the subject, but each month they are forcibly reminded of these defects through the pay envelope. As practiced on the iron ranges, however, the so-called "contract " system is not a contract and the name is a misnomer. No true contractual obligation exists. As usually practised, the contract system involves the setting of a price per foot in development work, or per foot or per car, usually the latter, in slicing or stoping, by the mining captain, and assumes its acceptance, though often under protest, by the men. A price is set for each working place, in which there are usually two men per shift. This price includes labor and supplies, such as explosives, fuse and caps, shovels, carbide, etc., and the men divide the total earnings less the amount expended for supplies. The cost of the supplies charged to the men varies

Jan 1, 1920

By Keith C. Hendrick

The mining industry of Canada, stretching from coast to coast and reaching into the most remote regions of the country, is of fundamental importance to the national economy and the well being of many communities outside the main urban areas. The production, processing and transportation of a host of mineral products provide employment for about 9% of the country's labour force; and their shipment to export markets provides an important contribution to the balance of payments. In 1976 Canada's metal and mineral production had a value of $5.24 billion, of which zinc and lead accounted for $862 and $129 million respectively, or 19% of the total. By all standards the Canadian zinc and lead industry is large and, therefore, important to the country as a producer and the world as a supplier. This report will review the development, describe the present status and discus current problems and future potential of the industry. The discovery and successful development of the major lead-zinc deposits at Kimberley, British Columbia, provided Canada with a solid base from which to grow. The breakthrough in metallurgical technology using differential flotation to separate the lead and zinc sulphides and the refining of high purity metal by electrolytic methods not only helped Canada to compete with other world producers but also provided a new source of these metals at prices and qualities that encouraged the development of new end uses.

Jan 1, 1977

By J. H. Smith, H. W. Paxton

ALTHOUGH many structural and kinetic investigations have been made for alloys of iron and nickel, only meager data exist from thermodynamic investigations. The purpose of this note is to estimate the free energy of the Fe-Ni solid solutions from thermodynamic data available for ternary alloys containing iron and nickel. The lack of a description of the thermodynamic behavior for the Fe-Ni system has required the structural and kinetic analyses of the system to assume some form of solution behavior, usually regular, e.g., the mar-tensite transformation analysis of Kaufman and Cohen, 1 consistent with the limited thermodynamic data. Indications that this system could exhibit ideal solution departures might have been suggested by the large deviations from additivity rules observed in the density and lattice-parameter measurements of Jette and Foote2 who interpreted this in terms of possible solute-solvent interactions. Later Turkdogan et al. 3 and more recently Ward and wright 4 found a minimum in the graphite solubility in liquid Fe-Ni solutions near the concentration of FeNi3 with deviations from linearity persisting at all concentrations. This was interpreted by Ward and wright4 to indicate negative heats of solution and was suggestive of short-range ordering. The infinitely dilute activity coefficient of carbon (?oC) was also observed by smith5 to pass through a maximum near the FeNi3 concentration in Fe-Ni solid solutions. Recent investigations of the liquid solutions over the entire concentration range by Zellars et a1.' and Speiser et a1.," using vapor-pressure determinations, revealed both negative departures from Raoult's law and a nonregular solution behavior. The solid alloys have been studied by Oriani 8 and Kubaschew-ski and von Goldbeck6 employing gaseous H2/H2O equilibria with Fe and FeO. Both investigations were in substantial agreement, indicating very small departures from ideality. However, Oriani observed the formation of Fe3O4 (instead of FeO) at XFe= 0.441 which severed the equilibrium and precluded experimental investigation of the nickel-rich alloys. Heat-capacity and heat-content measurements have been evaluated by Montgomery10 and found generally unsatisfactory for gleaning thermodynamic information. This is due to the unknown final states of the alloys caused by the interference of the martensite transformation on cooling iron-rich concentrations and superlattice formation, magnetic transformation, and the varied heat treatments used by investigators of nickel-rich concentrations. As an alternative to the experimental difficulties, indirect estimates of the solid-solution behavior have been made by Fleischer and Elliott11 and Smith et a1.12 From their measurements of the solubility of Fe-Ni alloys in liquid lead, Fleischer and Elliott calculated the nickel activity (aNi) (and integrated for aFe) by assuming: 1) liquid lead has no solubility in solid Fe-Ni alloys, 2) Henry's law is obeyed throughout the liquid lead-rich phase (0— 12 at. pct Nil, and 3) Henry's law constant is independent of relative iron and nickel concentrations. The estimate of Smith et a1.12 was obtained

Jan 1, 1964

Frank H. Probert, A.R.S.M., Morenci, Arizona (communication to the Secretary): The management of mines and the system of bookkeeping employed are subjects of great interest to mine-superintendents, and such papers as that of Mr. Davis callnot fail to attract attention. The Institution of Mining and Metallurgy, London, England, has done much within the last three years to promote discussion on the many systems adopted throughout the mining world; and any papers giving individual experience will benefit that class of men who are charged with the cconomical management of mining properties. It is often said that " a good mine shows a good manager," and more often that mismanagement is the chief cause of poor returns; or, as Mr. A. G. Charleton puts it, in his able paper on " Mining Accounts and Cost-Sheets,"* " accident may, and often

Jan 1, 1902