Search Documents

By J. Murray Riddell, George A. Morrison

This paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.‡ Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Bar-berton constitutes the world's deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 2-40 ft. Fractured sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra- turn of oil-bearing sandstone one foot thick was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), ? by 4 by 4-in. angle irons; spacing of sets. 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. The Shaft-sinking Operation The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (1) a storage pocket of 300 cu. ft, capacity with truck servicing facilities, and (2) pneu matically operated dump doors, which mere actuated by the hoistman, thus caring

Jan 1, 1946

By C. H. Jr. Herty

FEW subjects have attracted the attention of metallurgists more than ,oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction;, vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;1 furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A1203, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet-extraction methods' give only the more insoluble oxides Si02 and A1203, though the iodine method gives MnO to an uncertain degree (information that may be more misleading then no information

Jan 1, 1930

By E. P. Pfleide, L. W. Gibbs. J. R. Gross

A method using computer techniques is described for the comparative evaluation of truck performance over any given haul road using readily obtainable manufacturers' data. An additional computer program is utilized to calculate individual cycle times for each truck and shovel combination, fleet requirements for any desired production rate, and to estimate comparative costs. The introduction of a large number of variables into the program permits management to determine the critical system factors having the greatest bearing on costs. Thus, the method described can be used not only for analysis of needs for a new surface mine but for cost improvement in existing mines where changes in truck and shovel operations are contemplated. The systems analysis approach to the solution of problems in the mining industry is gaining in industry acceptance. This is a logical development in view of the fact that a mine constitutes one of the most dynamic systems of production. In contrast with a manufacturing plant, situated in a location selected through choice and utilizing a regulated source of quality controlled raw materials, the miner must go where the ore is and he is faced with ever changing physical conditions. He is subjected to the vagaries of nature, and he can never mine the same ore twice. What is systems engineering? There seems to be no concise and universally accepted definition of the term and its meaning is still fairly local. It deals largely with trade-offs of subsystem characteristics to achieve some desired result in an overall system. This concept of suboptimization can be explained by an example. If the objective of a mining company is to produce a certain quality ore at minimum cost, the optimum operation is not achieved by minimizing all costs, since all phases of mining are interrelated. Reduction of blasting costs might well increase loading, hauling, and crushing costs out of proportion to the resulting saving in explosives. Hence tradeoffs are necessary. It is evident then that an optimum system is achieved through a blending of suboptimal components which taken together yield the desired result. OBJECTIVE For our mathematical model we will assume the existence of a hypothetical new organization called Taconite Mining Co. (TMC). TMC has made an analysis of their orebody, their proposed operation, and

Jan 1, 1968

By d&apos, John C. Entremont

Pure iron was inductively melted in small refractory crucibles and optical pyrometer and immersion thermocouple readings were simultmzeously taken. The resulting emissivities of the liquid iron surface obtained were found to be greatly affected by both the gaseous atmosphere and geometrical changes in the physical setup. Quantitative values for these effects are indicated. FOR many applications in both the laboratory and plant, optical pyrometry is still the best means of measuring temperatures in the incandescent range. A prerequisite in evaluating the correct temperature is a good value of the emissivity of the surface. To obtain the emissivity from the tabulated values of the literature can be very confusing and often far from correct. There are many reasons for these difficulties, and it is not within the scope of this paper either to enumerate or to discuss them all. Its purpose is to show quantitatively how several factors affect the apparent emissivities obtained from experimental measurements on liquid iron surfaces. The black body is the reference state for the quantitative values of emissivities and is defined1 as a body which absorbs all radiation incident on it, reflecting none; such a surface emits more radiation per unit area per unit time than any surface which reflects any radiation, and is given a value of unit emissivity. All bodies having reflective power thus have emissivities less than unity and are considered nonblack or grey bodies. The ratio of the radiant energy emitted by the flat, nonblack surface to that of a perfectly black surface of equal area and temperature is the emissivity of the surface. The above definitions are applied to flat, polished, opaque surfaces, very seldom encountered in actual measurements, and for this reason many authors have suggested that the word "emittance" be used for real bodies rather than emissivity. The emittance has reference to the material and its configuration rather than to its properties in the idealized state. Recent observations of molten iron in a small refractory crucible indicate that not only the configuration of its surface but the geometrical arrangement of its surrounding and the nature of the surrounding atmosphere have a pronounced effect on the emittance. Neglect of changes in such conditions may lead to errors as large as 40°C at 1600°C. Thus it is suggested that the term "apparent emissivity" be used and that it be recognized that its value pertains to a particular experimental arrangement only. As a result of not recognizing these differences in emissivities, which are obtainable from changes in the physical setup of an observation, many investigators have incorrectly quoted their values as those of the emissivities of particular materials rather than as an apparent emissivity for their particular arrangements. As a consequence, values of the emissivity of liquid iron ranging from 0.3 up to 0.55 are found in the literature. In an effort to establish an accurate optical temperature scale for liquid iron solutions in which de-oxidation studies were to be carried out, it was observed that the temperature relationship, obtained by simultaneously taking immersion thermocouple

Jan 1, 1963

By A. H. Hand

When considering the question of future demand for crude petroleum in California, one must first decide whether it is to be approached in the light of the definition of "demand" when used in economics; i.e., "The quantity of any commodity required or sought in the market," or in the light of markets developed to dispose of total supply. Therefore, is the California demand of future years to be predicated on a continuation of supplying markets developed following the surplus production commencing in 1922, or predicated on supplying what would be termed economic markets ? If the latter, what are economic markets ? Obviously, the Pacific Coast States and Canada, Alaska, Hawaii and probably the Pacific side of Central and South America, can be considered as normal markets for California petroleum products. While there have been small quantities of gasoline shipped into the PacSc Coast from East Texas, transportation costs, plus import taxes in the case of foreign oil, are a sufficient barrier to justify considering that these markets will be retained. But how about our participation in Atlantic and Pacific foreign and intercoastal markets? During the five years preceding 1931 California shipped substantial quantities of gasoline to the United Kingdom and to France, Germany and Italy. During recent years our business in European markets has been restricted to occasional shipments of gasoline and Kettleman crude. This loss of business is occasioned by the development of production in the Mid-Continent, principally East Texas, and in Iraq, Rumania, Venezuela and other closer producing areas, which makes it impossible at the prevailing crude-oil prices for California to be competitive in supplying any substantial portion of these markets. It is therefore apparent that under a stabilized price structure that will return the California producer a reasonable price for his oil, future Atlantic foreign -business will be restricted to occasional spot cargo sales. As to Pacific foreign shipments which, in addition to Central and South America, consist principally of shipments to Japan, China, Australia and New Zealand: A considerable portion of the business we had with Australia and New Zealand until four or five years ago is now being

Jan 1, 1937

By Lester F. Engle

Books have been written, complex charts drawn, great batches of punched cards handled by ever increasing numbers of computers, and innumerable meetings held-all for the purpose of making effective the ultimate objective of new, revised or improved process facilities. It is to the credit of management, engineers, and others that in the vast majority of cases, the outcome of their work has been technically sound and economically rewarding. There is a way, however, to insure even better results.

Jan 5, 1966

By A. Kenneth Schellinger

DURING the comminution of a brittle material in the presence of dry air, no known phase change or chemical reaction takes place. The energy changes associated with the comminution are those of the transformation of kinetic energy into heat energy and the energy absorption represented by the actual rupture of molecular and/or ionic bonds. The random nature of the actual grinding process in a tumbling-mill often precludes the effective application of a rupture force on each individual particle of brittle mineral present. The result must be a great deal of useless vibration on an atomic scale in both the brittle mineral and the grinding medium below the elastic limit, which vibration is eventually manifested as heat energy in the mill. The actual rupture of molecular, or ionic, bonds creates new surface on the brittle minerals; each square centimeter of this new surface then must possess a number of potential bonds, each of which could reform theoretically with the release of energy. The sum total of this potential energy of bonding per unit of new surface, minus bond satiation effects of the enclosing gas or liquid, must be the surface energy of the mineral. If the comminution of the brittle mineral were carried out within the chamber of a calorimeter, the energy released as heat could be determined rather accurately. Moreover, the total kinetic energy input to the comminuting mass (mineral and medium) conceivably could be derived by a suitable torquemeter and revolution counter if the whole calorimeter were revolved. The difference between these two energy figures should then represent the net energy (gross energy input-heat energy output) used in creating

Jan 6, 1951

By Robert Gillham, Victoria Yablonsky, Grover R. Castle

INTRODUCTION The commercial paper market, unique to the United States, is a direct exchange of funds between high-grade borrowers and large lenders; because it eliminates both the bank's role as middleman and also some significant transaction costs, commercial paper is the lowest cost short term instrument in the world. For this reason, virtually all borrowers would like to enter the market, but only issuers with the highest rating from Moody's and Standard & Poor can attract purchasers at the best rates. COMMERCIAL PAPER The commercial paper market, in existence for over 100 years, has traditionally been used for short-term financings, with most paper maturing within 30-45 days. Under the U. S. Securities Act of 1933, (section 3(a)3) industrial paper can avoid registration only if it matures within 270 days and is used for current transactions. It was first used to finance the short-term seasonal working capital needs of manufacturing companies. Since World War II, commercial paper use has grown steadily, serving in the 1950's as the market in which finance companies financed the explosion in consumer credit purchases of heavy consumer durables. LETTER OF CREDIT BACKING As far as is known, the use of letters of credit to support energy-related commercial paper began about 13 years ago with an arrangement to finance the nuclear fuel for Con Edison's Indian Point 3 Plant. Goldman, Sachs was the architect of this financing and Chemical Bank provided the letter of credit support. After an early burst of interest, this type of financing wobbled severely in the difficult credit markets of the mid-seventies before regaining serious momentum in 1976 and 1977. A mining project would not normally qualify as a borrower in the commercial paper market because of its credit standing and because its large capital needs require long term financing. However, lately, commercial paper has begun to take the place of a bank term loan in limited recourse project financings. L/C backed commercial paper took this new and startling turn in 1982 when it was used as part of the $700 million financing for the development of the Newlands-Collinsville coal mines of Mount Isa Mines Ltd. in Australia. This was the first use of L/C backed commercial paper in a long-term limited recourse project financing. First Boston acted as financial advisor and, again, Chemical Bank provided sole letter of credit support of $155 million. The $785 million BHP financing for the acquisition of the Queensland (Australia) coal assets of Utah International from General Electric Company followed the next year; there we acted with two other Front Banks to provide $270 million of L/C support. These two important transactions indicate that not only has commercial paper become an integral part of a long-term financing package, but also that it is no longer the exclusive domain of the best known U. S. companies. Lesser-rated companies and a multitude of foreign borrowers have gained access to this "exclusive club." How has this become possible? OPERATION OF AN L/C An instrument of the commercial banks, the "direct pay" letter of credit, has enabled lesser-rated companies to issue commercial paper in their own names. The letter of credit allows the issuer to substitute the credit rating of the supporting bank for its own. The L/C in effect allows a lesser-rated company to rent the bank's credit rating. This upgrading is possible because the bank is unconditionally obliged to pay the note-holders at maturity and then turn to the Issuer for reimbursement. The Issuer commonly "rolls over" a new short-term issue and reimburses the supporting bank from the sale of the new issue until cash flows from the project allow the borrower to reduce the level of paper outstanding. The commitment for an L/C facility, up to 12 years in the case of the Broken Hill transaction, governs the life of the commercial paper tranche of the financing. The term of the L/C commitment thus has the power to extend the ordinary 30-45

Jan 1, 1985

By R. B. Tippin, J. S. Browning

The feasibility of multistage heavy liquid cyclone beneficiation of spodumene was successfully demonstrated in this investigation. The indicated recovery for the multistage circuits was mathematically estimated as continuous test runs would be necessary to determine the true influence of a middlings recycle. In the three-stage circuit, both the concentrate analysis and spodumene recovery exceeded 90%. The two-stage circuits were unable to simultaneously yield an acceptable produce with a satisfactory recovery. With the Nation's growing industrial mineral requirements, the U.S. Bureau of Mines has undertaken the task of investigating new mineral dressing techniques and improving the existing concentrating methods of ore beneficiation. One such project is the gravity concentration of minerals using heavy liquid separation (HLS).1-3 Heavy liquid separation is based on the simple principle that a material, whose specific gravity is less than the density of a solution, will float on top of the liquid and a material with a greater specific gravity will sink. Heavy liquid separation techniques were developed in the laboratory over half a century ago but the process has yet to be commercially adopted. In the past, commercial operations have failed because of numerous problems.4 Industrial interest has recently been reactivated because of engineering advances. The number and quality of the heavy liquids suitable for mineral processing has increased while the cost has sharply dropped. New and improved liquid recovery systems5,6 are under consideration with present emphasis on 1) solvent extraction, 2) thermo-evaporation, and 3) water washing. The toxicity of the heavy liquids7 presents a problem, but throughout the chemical and mining industries, many similar hazardous materials are safely handled. A distinct advantage of using heavy liquids is its ability to provide a near perfect separation of fine-sized mineral particles even when the specific gravities are close. Effective separations have been made on minerals down to 200 mesh and with a density

Jan 1, 1968

Roger A. Markle was sworn in as director of the US Bureau of Mines on September 27, 1978, ending a 20-month period during which the Bureau was without a leader. Some Bureau observers wondered out loud if this delay was a signal that Interior was slowly pulling the rug out from under the agency. When Markle was finally tapped for the director's position-coal industry executive to lead an agency that had been stripped of its fossil fuel R&D functions as well as its safety and health enforcement role--the speculation was fast and furious: One camp had it that Markle was brought in to phase out the Bureau; others said that Markle's directive was to revitalize the organization by charting a new Bureau course. In March, with the proposed Department of Natural Resources making headlines, ME went to Washington to interview Markle about his first six months as director and the goals he has set for the Bureau's future.

Jan 4, 1979

By Kiyoshi Sugasawa

At Sumitomo Metal Industries, technologies for manufacturing metallurgical coke have been developed, under the names of Sumicoal System and DKS formed coke processes. Sumicoal System is the process utilizing approximately 70% conventional fine coal, 30% briquettes charge, and 2-3% caking substance. This technology was industrialized in 1975, and now the blending ratio of non-coking coal has reached up to 20%. On the other hand, a large scale demonstration plant using the DKS process was constructed and operated over one year. As the result of that test, it is thought that the DKS process has also reached the stage of industrialization. This paper will describe these new coking technologies.

Jan 1, 1977

By D. Foster Hewett

The scope of this paper is the description of two districts in Peru in which deposits of vanadium have been found, and the consideration of much laboratory-work that I and others have done to determine the nature of these deposits. It is with regret that I present some of the data in a state of evident incompletion, particularly the analyses of a few of the minerals, which leaves some doubt as to whether the true nature of the migerals is understood. I make no apology, however, since in this case, as in many others referring to ore-deposits, conclusive opinions cannot be stated until a great amount of work has been done, and the deposit has been thoroughly exploited. I believe that the data and the tentative conclusions here presented indicate a unique and interesting condition which may assist others in work along similar lines; arid further, what is of more practical importance, stimulate a search for a metal which, though long considered rare, is probably so merely because proper care has not been taken to recognize it. An excellent bibliography on the occurrence of vanadium in nature is given by I?. W. Clarke in his paper, Data of Geochemistry;' and in the preparation of this paper 1 have consulted many of the references contained in the Bibliography of the Chemistry of Vanadium, by M. Moisan.2 A brief review of the subject having special reference to the metallurgy of vanadium is contained in the small book by P. Nicolardot.3 One of these vanadium-deposits has already been briefly. 1 Bulletin No. 330, U. S. Geological Survey (1908). 2 Chimie Minerale, vol. iii. (1905). 3 Le Vanadium (1905).

Jan 1, 1910

The Committee, appointed early in May, met and organized in Washington, May 9, 1923, and were then advised that such data as they required would as far as obtainable be submitted to them in tabulations, and that they could not be allowed to see the individual reports nor know the identity of the operators on whose reports the figures submitted were based, therefore the Committee's valuation is based on data received from your statisticians, and on tonnages estimated by your staff and by the United States Geological Survey. Various methods of valuation for mining properties have been suggested, but all authorities seem to agree in accepting, as the fairest and most practicable and logical, a capitalization of the estimated future earnings, when such estimate can reasonably be made. Hoover and Finlay both emphasize this. The United States Supreme Court says in Cleveland, Cincinnati, Chicago & St. Louis Railway Co., v. Backus, 154 U. S. 439: But the value of the property results from the use to which it is put and varies with the profitableness of that use, present and prospective, actual and anticipated. There is no pecuniary value outside of that which results from such use. The amount and profitable character of such use determines the value. The Committee on Federal Taxation of the American Institute of Mining and Metallurgical Engineers, appointed in 1919, in its report states: A proper value of a mining property is the present value of the prospective net earnings, taking into account probable variations in output and value. Ingalls ("Wealth and Income of the American People," p. 97) says: The fundamental principle of mine valuation is the present worth of an annual dividend accruing during the period of years corresponding with the lie of the mine. It is a convention that the estimated period shall not be more than 30 years.

Jan 1, 1924

By Benjamin LeRoy Miller, Joseph T. Singewald

The ore deposits at Firmeza have been worked continuously since 1884; those at Daiquiri since 1895. It is surprising, therefore, that they have not been the object of careful geologic study until quite recently. It is true that considerable attention was paid to these deposits by A. C. Spencer, in 1901, in the report on the geology of Cuba, by Hayes, Vaughan, and Spencer,l but this was only incidental to a hasty general reconnaissance of the Island. As far as the Daiquiri deposits are concerned, this gap has been filled by the appearance of the two papers by Prof. James F. Kemp2 and by Prof. Waldemar Lind-gren and Clyde P. Ross respectively.3 Max Roesler, first holder of the Emmons fellowship, made a detailed study of the Firmeza deposits during the past summer, so that soon we can expect a full description of them. Consequently, there is no, demand at the present time for a description of the deposits from other sources, and that is not the purpose of this paper. The papers on Daiquiri, however, leave unsolved problems in regard to the age of the rocks of the district and certain phases of the genesis of the deposits, and it is with the hope of aiding in the solution of some of these problems that this contribution is offered. Kemp, and Lindgren and Ross agree in assigning these deposits to the type of contact metamorphic deposits. They disagree in part on the question of their localization. The deposits occur in an extensive area of diorite which includes numerous blocks of limestone, and sometimes are found in the contact zones between these blocks and the diorite, and in other instances are completely enveloped in the diorite, showing no apparent connection with the limestone. The latter class includes

Jan 1, 1916

TO THE BOARD OF DIRECTORS OF AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-I have the honor to present the following, report for the calendar year 1920. The activities which seem to call for special comment are: THE NEW FORM OF MAGAZINE MINING AND METALLURGY appeared every month during the calendar year and has been developed until it contains some ten departments. It has brought forth more commendatory letters than have been received at headquarters on any other subject throughout the year. Less than a dozen letters unfavorable to the change have been received, and the indications are that the magazine has met a want deeply felt, especially by members distant from headquarters. The technical papers printed by the Institute are published in abstract in the magazine and opportunity is given to members who desire them to receive full copies of any or all papers published. The Bound Volumes, as usual, contain all the papers in full and discussions thereof. FINANCES The greatly increased cost of paper and printing has put a tremendous burden on the Institute's finances, since the dues of $12 per year are only 20 per cent. greater than the members paid when the Institute was founded forty-nine years ago. This has resulted in a temporary deficit, similar to that encountered by many of our sister engineering societies. The fact that our Institute has lower dues and gives more in the way of publications to its members than any other of the national engineering societies has rendered the situation more difficult for us. MEETINGS The Annual Meeting in New York, the Field Meeting in the Lake Superior District, the meeting of the Petroleum and Gas members at St. Louis, and of the Institute of Metals Division in Columbus, Ohio, have all been described in full in the magazine.

Jan 1, 1925

By J. G. Davis, P. C. Thakur

Hazardous methane gas in coal mining is receiving increased attention due to the increased US demand for coal which has resulted in the exploitation of deeper seams and the utilization of more productive equipment. Problems posed by methane emission has the Mining Research Division of Continental Oil Co. (Conoco) accelerating efforts that began in the early 1950's with Consolidation Coal Co. (Consol).1 The program's focus is on finding new techniques for degasification of virgin areas as well as control of methane in gob areas.

Jan 10, 1977

By R. J. Brison, O. F. Tangel

The development of a new method of mineral separation was sponsored by the International Salt Company, which requested Battelle Institute to investigate means for improving the quality and appearance of rock salt from the Company's Detroit mine. Although developed specifically for removing impurities from rock salt, the general method may be applicable to other separation problems. The principal impurities in rock salt from the Detroit mine are dolomite and anhydrite which represent 2 to 5 pct of the weight of the mined salt. In the size range from 114 to 112 in. (the range of primary interest in this project) the impurities are only partially liberated from the halite in normal production. Further size reduction to improve the liberation of impurities is not practicable in view of the market requirements for the coarse grades of rock salt. Laboratory separations in heavy liquids showed that, to improve the quality and appearance of the rock salt substantially, it would be necessary to remove not only free gangue particles but also a large proportion of the locked-in particles.

Jan 8, 1960

By A. A. Burr, D. Caplan

IN carrying out experiments in metal-gas systems, it is often difficult to estimate how long a reaction period must be allowed for equilibration. This is especially true in systems for which the diffusion coefficient is not known. In an investigation of the Cr-O system, the necessary information was obtained in the way described subsequently. Two pieces of chromium sheet of different thicknesses were packed in mixed powders of chromium and Cr2O3 and sealed into an evacuated metal capsule by welding. Austenitic stainless steel proved suitable as a capsule material up to 1350°C and molybdenum at higher temperatures. The capsule then was heated at a specific temperature for a time sufficient to saturate with oxygen the thinner but not the thicker specimen. The time is readily estimated from a preliminary experiment if a sufficient thickness differential is chosen. Under these experimental conditions, the metal sheet is exposed to a partial pressure of oxygen equal to that of the dissociation pressure of the oxide and hence can become saturated with oxygen without developing any second phase. After cooling, both samples were analyzed for oxygen by the vacuum fusion technique. Assuming that the surface of the specimens is kept saturated with oxygen throughout the experiment, the diffusivity can be calculated by application of the appropriate solution to Fick's second law. This is most conveniently accomplished by use of a plot of mean fractional saturation (Cm-Co) / (Cs-Co) vs (Dt) ½/L as given by Darken,' where t is time, L the half-thickness of the sheet, and D the diffusion coefficient. Cm, the mean concentration at time t, is given by the oxygen percentage in the thicker specimen; Cs, the constant surface concentration, is the oxygen percentage in the thinner specimen; Co is the oxygen content of the original chromium sheet. (Cm-Co) / (Cs-Co) is calculated and the corresponding (Dt) ½/L is read from the graph and D thereby calculated. By performing the experiment at two temperatures and plotting log D vs 1/T, the D for any temperature is established. (The activation energy for diffusion may be obtained from the slope of the line.) Once D is known as a function of temperature, it is a simple matter to estimate the correct reaction time for experiments with single specimens at other temperatures by equating (Dt) ½/L to its value for effective saturation. Darken' points out that this is approximately unity. The solubility of oxygen in chromium, as determined from the thin samples at each temperature, proved to be approximately 0.03 pct at 1350°C and less at lower temperatures. Due to low solubility and to the known difficulties of the vacuum fusion method in this low range, the values obtained for D (5x10-0 sq cm per sec at 1350°C) are estimated to be correct only within an order of magnitude. Nevertheless, the method has proved useful in estimating reaction times. Its usefulness will be greater in metal-gas systems where the solubility is appreciable. A second function of the method is to permit the determination of diffusion coefficients in systems for which the conventional techniques are experimentally difficult or impossible.

Jan 1, 1956

By Walter C. Smith

THE Cerro de Pasco Copper Corp. began to produce bismuth at the Oroya smelter in 1929, at which time the only important consumption of that metal was in the manufacture, of pharmaceutical compounds, and the normal supply of metal exceeded the demand. With a new and major producer entering the field, additional uses for bismuth had to be developed. A survey indicated that the most promising opportunity lay in fusible alloys containing bismuth. A large number of bismuth alloys were known and a few of them were being used in the manufacture of automatic sprinkler heads and safety plugs. The literature cover in,- the- alloys was found to be sketchy and contradictory. Research, development, and educational work carrried on by the Corporation during the past fifteen years has resulted in greatly enlarged uses for the metal. In general the low-melting bismuth alloys are of high specific gravity, relatively soft, of low tensile strength, brittle to shock, yet subject to plastic

Jan 1, 1945

By Alfonso W. Ovalle

INTRODUCTION The block-caving mining method is one of the most economical ways existing today to extract ore from nature. It is undoubtedly the least costly of the underground systems and moreover it compares favorably to open-pit mining. In addition to its low cost characteristic, the block-caving mining method permits a great extraction volume as can be exemplified by El Teniente's output capacity of over 22 million tons of ore per year. These characteristics of block-caving give assurance that, even though it is a very old mining system, it will be a good answer to the many future large massive low ore grade deposits to come and a1 so to rep1 ace open-pi t mining as such operations get deeper with higher stripping ratios. These are the reasons that induce further study of block-caving. In this paper block-caving at El Teniente is analyzed with due consideration to the major problems that this mine will encounter. Emphasis is given to the factors influencing the mining of soft ore which accounts for most of the ore to be extracted in the next ten years. A separate paper is devoted to a major modification introduced to block-caving hard primary ore at El Teniente by means of LHD equipment extraction. DESCRIPTION OF THE PRESENT MINING Ore Production and Flow Over 62.000 tons per day of ore are extracted 359 days per year at the El Teniente Mine. The Teniente 8 train haulage level at 1.983 m takes 29.000 tons daily to the Col6n Concentrator. Two trains make the 8 km haul with 16 cars per train. Car capacity is 90 tons. The Teniente 5 train haulage level 298 m above takes 33.000 t per day to the old Sewell Concentrator. Ore is produced from three production areas in two different levels. The so called North Mine produces 42.000 tons daily from the Teniente 4 level 65 m above the Teniente 5 haulage level. The Central Mine produces 1.000 tons from the first hard rock block caved at the Te- niente 4 level. The combined 43.000 tons per day production is sent through inclined 2 m dia- meter raises to the Teniente 5 haul age level , where 33.000 tons are taken 2.5 km to the Sewell Concentrator and 9.000 tons are hauled 0.5 km to a 5 m diameter vertical ore pass which sends ore to Teniente 8. The haulage is by 7 trains, 15 gabble-bottom cars per train. Car capacity is 20 tons. The so called South Mine produces 19.000 tons per day from the Teniente 1 level 645 m above the Teniente 8 haulage level. Ore is transferred by 2 m diameter inclined raises to the Ten 1 Retram level 22 m below, where 5 trains with 20 Sandfor Day cars per train, 8 tons capacity per car, haul the ore 1.5 km to two vertical 5 m diameter ore passes which connect to Ten 8. Starting in 1982 the Central Mine will in- crease production to 6.000 tons per day. An in- dependent loop haulage system will start operat- ing at the Teniente 5 level to feed a new under- ground 1.372 mm (54 in.) gyratory crusher which will send minus 152 mm ore (9 in.) to Teniente 8. In two or three years time the North Mine will only feed the 33.000 tons to the Sewel 1 Concentrator with its old Teniente 5 haulage system. The Col6n Concentrator will be fed from the Central and South Mines. Figure 1 shows the transfer systems and ore flows. The Ore Body In plan view at the Teniente 4 level the ore body has a kidney shape 1.800 m long and between 400 to 700 m wide. The north-eastern section of the ore body was washed away by the Teniente River. At the Sub 5 Level, 125 m below Teniente 4, the mineralization completely surrounds the circular 1.000 m diameter steep-sided barren breccia pipe (Braden pipe) . The ore body rock is 73% andesite, 14% diori te, 13% dacite and 6% mineralized breccia. Most of this ore is secondary enrichment sulfides which apart from the dacite is strongly fractured being chal cocite, cove1ine , bornite and

Jan 1, 1981