Search Documents

By E. Morgan Massey

Located in virgin coal acreage near Gilbert, W. Va., Massey Coal Mining Co.'s Ben Creek No. 2 mine afforded the company's engineers the opportunity of designing and laying out the entire mining operation from the mine faces to the railroading loading site. However, the topography of this region posed difficult problems in haulage of coal for, in this extremely rugged terrain the uppermost coal seams lay in the mountain-top ridges, approximately 1400 ft above the valley floor. The decision for mining equipment naturally leaned to the new high-capacity continuous miners where seam conditions permitted: otherwise, to the new super-high capacity conventional cutting and loading machines. Since the coal seams lay in ridges and points of considerable outcropping, the decision was to keep the transportation on the surface and mine the coal with multiple entries into the outcrop. This way, the major problems of underground haulage, drainage, and ventilation are eliminated, and the opportunity to take advantage of a-c underground power becomes a much simpler proposition.

Jan 10, 1960

By Richard D. Snouffer

Prime topics of conversation these days are the new concepts of rail haulage for bulk items such as iron ore, potash and coal. We have heard such ideas as the "integral train" and the "unit train" discussed frequently during the past two years at various AIME meetings, and progress reports have kept up a steady appearance in the technical press and in local newspapers. While no railroad has a complete "unit train" in service at this moment, one has 50 fast-discharge cars under construction and the Pennsylvania Railroad has experimented with radio-controlled motive power distributed at intervals throughout the train. To a great extent, however, the promise for greater efficiency and lower costs held out to industry by these new haulage methods is dependent not on greater speed or larger cars or more dedicated equipment alone but, rather, on the utilization of modern practices in the loading and unloading of rail cars. It is the purpose here to examine these two key steps and the up-to-date procedures and equipment they entail.

Jan 7, 1963

By G. R. Fitterer

Trends in slag composition in acid open hearth practice, particularly the variation in iron and manganese oxides during refining, are reviewed. A procedure which is currently being used to control the refining reactions is described and partially explained through slag phase diagram considerations. In addition, the ionic nature of these slags is considered and it is proposed that silica combines with the oxide ion and forms a series of complex silicate ions. The effect of basic oxides such as FeO, MnO, and CaO is apparently additive in furnishing the oxide ion for this purpose. IT is now possible to control192 the refining of steel in an acid open hearth furnace to a surprising degree. This control has been brought about through the knowledge and use of several facts and tests. These are: 1—A planned charge analysis based on a knowledge of the type of fuel, the bath depth, etc. 2—Knowledge and control of rate of fuel input as well as its method of atomization, if any. 3—Determination of the slag fluidity. 4—Bath temperatures (use of the Pt-Pt-Rh thermocouple). 5—Periodic determination of carbon content (use of the Carb-analyzer or Carbometer). Through the use of these control methods, a heat may be made to "melt-in" with or without residual manganese and silicon. The rate of refining or carbon elimination may be controlled accurately, and the desired tapping (or "go-ahead") carbon may be approached at a rapid or slow rate according to preference and type of steel being made. Thus operating time may be predetermined and greatly reduced. Further, all of the refining can be done without any ore or other oxidizing additions, and the heat may be brought to the desired tapping temperature simultaneously with the attainment of the desired carbon analysis. This control procedure is being used in most acid plants in the United States today and has been de- scribed.', ' Although the slag metal relations are sufficiently well known to control the heat as stated, yet it is possible to account for only about two-thirds' of the 0, which must have been used for the elimination of the carbon and other metalloids. Phase diagram studies' of the slags, slag weights, the metal particle theory,' ore additions, limestone additions, etc., may all be taken into consideration; yet, the mechanism of oxidation and source of all the oxygen remain to be explained. This paper reviews some of the principles upon which the control methods were based and proposes other possibilities regarding the unexplained phenomena. Old and New Acid Open Hearth Practice Some of the recent statements in the literature regarding acid open hearth operation are based on old heat data which are not typical of modern American practice. These old heat logs have been responsible for many misconceptions regarding the acid hearth practice and represent heats which do not coincide with modern methods. In recent years, American practice has been altered materially and these changes will be briefly described. Modern American Practice: A typical log of a modern American acid open hearth heat' is shown in Fig. 1 which indicates that the refining time was only two hours, during which the carbon was eliminated rapidly and the bath temperature increased at a fast rate. The manganese and silicon contents of the metal were essentially eliminated and their oxides had become constituent parts of the slag at the "melt-down" period. During the course of the heat, the MnO content of the slag remained practi-

Jan 1, 1954

By AIME AIME

PERHAPS the outstanding characteristic of the newly elected President of the Institute is his rare ability to set aside nonessentials, and pick out the few basic elements on which a valid conclusion on any question can be drawn. This holds whether he is appraising a mining enterprise, selecting a man for an important position, deciding whether to buy or sell a bond, or choosing the best method for mining a huge body of ore. For example, he has pointed out that the two primary factors that make for success in a copper-mining venture are a large reserve of reasonably good ore and competent management. Usually the first is not as difficult to gauge accurately as the second. In a big enterprise the quality of the management

Jan 1, 1939

By W. L. Zeigler

THE year 1930 in the Ceur d? Alene district was one of curtailment in production. Many of the small properties were closed entirely and only three large. producers, the Bunker Hill & Sullivan, Hecla, and the Morning mines were left producing at capacity. No innovations in milling were evident, but progress was made in reducing costs as is always necessary in times of low metal prices. One new concentrator was constructed, a 500-ton daily capacity selective flotation plant for, the Jack Waite Mining Co. This mill uses coarse crushing, followed by hand sorting, for both a high-grade ship- ping ore and waste. The remainder of the ore leaving the sorting belt is crushed in a new type Traylor reduction crusher to %-in. size and stored in large capacity mill ore-bins. The grinding is done with ball mills, in closed circuit with a Dorr classifier to 75 per cent - 200 mesh. Minerals Separation 24-in. flotation machines are used both for a lead and a zinc concentrate, with double cleaning in each case. The concentrates are dewatered in Dorr thickeners and filtered on Oliver late-type filters.

Jan 1, 1931

In the January Bulletin a list was published of Societies' publications, magazines, etc., which were duplicates and were discarded at the time of-the consolidation of the libraries of the three Founder Societies. A second list published herewith includes text books which are duplicates and which will be disposed of about April 1, 1916, by the Board of Directors of the Institute through the, Library Committee.. If, meanwhile, members desire to secure some of these books, they are asked to communicate at once with the Secretary as. this is an unusual opportunity to secure books at an extremely low price. Airy, George Biddell.-Magnetism, London, 1870, Bd. Alberti, Friedrich von.-Halurgische geologic. Erster Band. Zweiter Band. Stuttgart, 1852, Bd. American Iron and Steel Association.-Ann. Rep. of the Sec'y. Statistics of American and, Foreign Iron Trades, 1877. Phila., 1877, Bd. Same, for year 1878. Phila., 1879, Bd. American. Telephone and Telegraph Co.-Ann. Rep. of Directors to Stockholders, 1911. N. Y., 1912, paper. Armagnat, H.-Induction Coils. Trans. by Otis Allen Kenyon, N. Y., 1908, Bd. Armstrong Cork Co. Insulation Dept. Nonpareil Corkboard Insulation. Pittsburgh, 1909, Bd. Associazione fra gli Industriali Metallurgici Italian.-The Metallurgic industry of Italy. Description of some of the principal works. Milan, 1911, Bd.

Jan 2, 1916

By Frank M. Stephens, Robert D. Macdonald

As processes for handling low-grade or complex ores become more complicated and as new methods are found, the need arises for more complete and detailed pilot-plant studies to protect the capital investment required for a full-scale plant. Occasionally a process is firm technically, but there is a need for a demonstration plant that will convince nontechnical men of the wisdom of investing in a full-scale operation.

Jan 5, 1959

By James C. M. Li

The Petch relation between the flow stress and the gain size is derived from a consideration of gain boundary sources of dislocations without the need of dislocation Pile-ups. Three mechanisms for inierpreting the yield stress: the gain boundary strength, the unpinning of Frank-Read source near a grain boundary, and the generation of dislocations from the grain boundary are compared and the condition of their equivalence is shown. The effect of the average angle of misfit of pain boundaries is found to be sma11 and so is that of the average angle of misfit of subboundaries having impurities. The effect of impurities on the ledge density in the grain boundary is treated thermodynamically and a relatwn is proposed for the variation of Petch slope with impurity activity. The effect of temperature on the Petch slope is interpreted as due to the change of ledge structure in the grain boundary. It is indicated that the effect of annealing temperature may be more important than that of the test temperature and therefore should be studied. The effect of plastic strain on the Petch analysis is deduced from a work-hardening equation in which the generation of dislocations has first-order kinetics and the annihilation of dislocations has second-order kinetics. It is concluded that the Petch slope will decrease with plustic strain if the rate of annihilation of dislocations is sufficiently large. Critical experiments which may shed light on the mechanism for the Petch relation are suggested. THE relation between the yield or flow stress, 0, and the grain size, l, was first proposed by all' and later studied more extensively by Petch and co-workers, who also proposed a similar relation for the fracture stress and deduced from these a grain-size effect of the ductile-brittle transition temperature. The microscopic mechanism used by all' and petch2 involves a pile-up of dislocations of like sign generated from a Frank-Read source. The yielding or flow takes place when the pile-up exerts sufficient stress at the grain boundary so that the plastic deformation can propagate from one grain to another. If the average strength of the grain boundary is ai and the average length of the pileup is lp, the Petch slope, k, is given by" where p is the shear modulus, b the Burgers vector, and v the Poisson ratio. This slope will be independent of the grain size if l/lp is a constant. This is possible, since, if the Frank-Reed source is situated near the grain boundary, lp = 1, and if it is situated in the middle of the grain, Ip = 1/2. cottrell,12 also using the pile-up mechanism, proposed that the stress concentration at the grain boundary will initiate Frank-Read sources near the grain boundary and in this manner a Lüders band can propagate from one grain to another. Assuming that the average distance between the Frank-Read sources and the grain boundary is 1, and the unpinning stress of the Frank-Read sources is op, Cottrell obtained the following Petch slope: This slope will be independent of the grain size if ls is independent of the same, which is not as obvious as the condition, Ip = I for Eq. [2]. In addition to this assumption, the direct relation between the Petch slope k and the unpinning stress, up, was recently questioned by Johnsonon grounds that it is inconsistent with the following observations: the independence of k with temperature and strain rate, and the small k in columbium, which, like iron, has a sharp yield point. As pointed out by ohnson," the most important objection both to the Hall-Petch mechanism, in which the strength of the grain boundary plays the role in yielding, and to the Cottrell mechanism, in which the unpinning of Frank-Read sources plays the role in yielding, is the lack of direct observation of the pile-ups. The dislocation structure in deformed iron has been examined recently in the electron microsope.'-' Dislocations appear to be generated from grain boundaries or other interfaces; they form clusters and tangles within the grain at very early stages of deformation, even in the Lüders band, if the deformation is slow or at normal and elevated temperatures. Although it is still too early to interpret bulk properties from thin-film observations, it does seem worthwhile to look for a mechanism for the Petch relation which does not require dislocation pileup. SUBBOUNDARY SOURCES In order to show that a consideration of grain boundary sources can lead to the same Petch relation as does the consideration of the strength of the grain boundary, we shall first discuss the case of a simple tilt boundary whose elastic properties have been studied in detail.17 The strength of a partially

Jan 1, 1963

By E. W. Felegy

THE need for improved mine communication to increase efficiency and to insure greater safety has long been recognized. General and unrestricted communication between all points underground, and between the surface and all points underground, is probably the least advanced phase of the mining industry. An ideal system of mine communication must require no fixed wire installations. The equipment must be small, lightweight, and readily portable, and the power requirements low. A system that can be used not only under normal circumstances but also in an emergency, when the continuity of wires, tracks, and pipelines may be disrupted, must function independently of any aid furnished by standard installations. Radio communication offers possibilities of meeting all the requirements necessary for an ideal communication system in underground mines. Transmission of signals must be achieved through one or both of two mediums, through the air in mine openings or through the strata. The results or lack of results obtained by early investigators showed conclusively that radio communication by space transmission cannot be accomplished effectively beyond line-of-sight distances in underground passageways. A radio system underground therefore must depend solely upon transmission through soil and strata. The application of radio to underground mine communication was investigated by many individuals and agencies at different times in the last several decades, but little success was achieved before World war 11.2-0, The results of experiments during the war, and further knowledge gained in experiments with vastly improved communication methods and equipment after the war provided the background for additional research in radio communication in underground mines. During 1950 to 1.952 the University of Minnesota sponsored an investigation to determine the possibility of developing: a system of radio communication universally applicable in underground metal mines in the Lake Superior district. The possibility of using radio equipment to determine the imminence of rock bursts in deep copper mines in that district also was investigated. The investigation supplemented previous and concurrent emergency mine communication studies of the U. S. Bureau of Mines. Testing equipment and laboratory facilities maintained by the Bureau of Mines at Duluth, Minnesota, were used in the research program, which was conducted as a mining engineering graduate research problem by the present writer under the direction of T. L. Joseph and E. P. Pfleider. The radio units used in the research program were designed and built to specification solely to conduct tests of radio communication in mines. Two identical units were used in all tests. Each unit contained a transmitter section, a receiver section, and a power-supply section, mounted on a single chassis. The entire unit was enclosed in a single 10x12x18-in. metal case provided with a leather-strap handle for carrying purposes. The front of the case was hinged to open upward and provide easy access to the single control panel on which all controls were mounted. Storage batteries supplied the operating power for all tests. Standard 6-v automobile batteries were utilized to provide adequate capacity to conduct tests for a full day without exhausting the battery. A frequency range from 30 to 200 kc was covered in eight pre-fixed steps on each unit. The carrier frequencies were crystal-controlled and amplitude-modulated. The receiver employed an essentially standard superheterodyne circuit and was sufficiently sensitive to detect signal strengths of 5 micro v. A heterodyne circuit was employed in the transmitter to obtain the low-carrier frequencies used in the units. Power output of the transmitter, usually less than 2 w, rarely exceeded 3 w in any test. Tests were conducted in mines on the Vermillion iron range in Minnesota, the Gogebic iron range in Wisconsin, the Menominee and Marquette iron ranges in Michigan, and a copper mine in the upper Michigan peninsula. All tests were conducted when the mines were operating normally, and usual mining, maintenance, and transportation activities were in progress, so that any interference caused by normal production activities could be evaluated during the tests. Tests were made between different points underground in each mine, and between underground and surface points at some mines. Test readings obtained at any one mine were calibrated in the laboratory before another series of tests were begun at the next mine. The transmitter and receiver were separated by one or more levels in each test, and generally there was no other means of communication between test points. Two 100-ft lengths of rubber-covered wire were used for antenna wires on each unit in both transmission and reception. The ends of the wires were connected to ground points in one of several methods, depending upon physical conditions at each test site. The wires were clipped to metal rods about 200 ft apart in the back, side, or bottom of the mine opening where the character of the rock permitted driving rods. Both wires were clipped to points about

Jan 1, 1954

By R. W. Jenkins

TRACKLESS equipment is being used by the Coplay Cement Manufacturing Co. to develop a folded limestone deposit economically and safely with inexperienced men. Cost and quality of development stone results in a saving when it is used in- stead of outside sources of limestone. This favorable cost has been attained by following a methods development and training program described in this paper. It is expected that further savings in favor of the mined stone will be made when stopes now being prepared are in production. The present equipment will be used for loading from stope draw points. The limestone is blended with quarried cement rock to serve as raw material for Portland cement, first produced in this country by Coplay Cement Manufacturing Co. from a process developed by its president, David 0. Saylor, in 1873. For many years the cement rock alone or with a small amount of added limestone was used for raw materials. Later as specifications were raised and the richer portions of quarries were depleted, limestone from outside sources was required in increasing amounts. In 1925 D. J. Uhle, the general manager, began to prospect company property for limestone.

Jan 1, 1954

By John C. F. Randolph

(Read at the Amenia Meeting, October, 1877.) Tits establishment being now in full working order, it has seemed of considerable professional interest to collect together, in a concise form, the various points as to its plan, method of dressing, and equipment. The data contained in this paper have been largely drawn from the able paper of E. Kutscher, constructing engineer. of the works, contained in the Zeitschrift fur Berg-Hütten-und Salinenuesen im Preussischen Staate, 1873, supplemented by some personal memoranda made while the works were under construction and by memoranda on the works appearing in various German technical papers from their completion up to date. This is probably the largest dressing works in the world devoted to the beneficiation of argentiferous lead ores, and it is doubtful if any establishment for the concentration of mineral of any description can compare with it in size. As showing the final practice adopted in an old and very conservative mining region, in which the concentration of ores has been a matter of constant practice and experiment for a very long period, these works are of peculiar interest. The fact that the Clausthal ores strongly resemble a very large and abundant class of ores found in the United States has always attracted the attention of American mining engineers and mine owners to the methods employed in dressing and smelting them. The study of their methods of concentration of ores has, however, always been full of difficulty,

Jan 1, 1878

By John H. Bassarear, Harold W. Sorstokke

The fourth expansion within 10 years was completed at Pima Mining Co. during late 1971. The first three expansions increased capacity from 3000 to over 40,000 tpd. Conventional crushing and grinding practices were used in the original 10-section mill. Total capacity is now approximately 54,000 tpd. Expansion IV includes a new primary crusher and a radial stacker conveyor that feeds stockpiles for both concentrators. The -8-in. primary product is fed from the reclaim stockpile to the new mill by two pairs of pan feeders, each pair feeding a separate conveyor. The reclaim conveyors each feed 28 X 12-ft semiautogenous mills operating with an 8% charge of 4-in. balls. Autogenous discharge is screened, oversize recycling by conveyors, with -%-in. undersize feeding two conventional 161/2 X 19-ft ball mills in closed circuit with cyclones. Cyclone overflow is pumped to three parallel rows of 300-400 cu ft flotation cells. Rougher and scavenger concentrates produced are sent to the original mill for regrind, cleaning, and filtering.

Jan 1, 1974

By R. G. Jones, W. L. Kinney, R. E. Schilson, R. S. Wilson, G. A. Clark, H. Suralo

This paper discusses the results of the Fry conventional or cocurrent in situ combustion test, which was conduct-ed in a 3.3-acre inverted five-spot. The depth of the formation was between 880 and 936 ft; the oil had a specific gravity of 28.6° APl and a viscosity of about 40 cp at the reservoir temperature of 65°F. Preceding the combustion test, air injection tests were conducted which, in conjunction with geological studies, were used to evaluate the characteristics of the reservoir. Combustion was initiated on Oct. 13, 1961, with ignition being accomplished by a 40 kw electrical heater. The test phase of the project ended on Oct. 1, 1963. During the test, the average air injection rate was 1,520.-000 scf/D. Throughout the test, production of all fluids— gas, oil, and water—was monitored. Cumulative oil production credited to the project was 100,586 bbl. The cumulative air-oil ratio was 11,500 scf/bbl oil, and the oxygen uti1ization efficiency was 87 per cent. INTRODUCTION The Marathon Oil Co. conducted a successful in situ combustion test, beginning Aug. 22, 1961, at the Fry unit, Crawford County, 111. The purpose of the project was to test the feasibility of cocurrent in situ combustion as a means of oil recovery in the Fry type reservoir. Interest in in situ combulstion as an oil recovery tool has been stimulated mostly by the existence of large reserves of heavy viscous crudes with low expected recovery, usually less than 10 per cent. These are the so-called unrecoverable reserves, and most combustion tests to date have been conducted in this type of reservoir.1-4 In contrast, the Fry combustion test was conducted in a reservoir with a relatively high gravity oil having a relatively low viscosity. This paper discusses the performance of the test. The geology of the reservoir and the field operations are discussed in separate papers.5 TEST SITE The Fry combustion test was carried out in a 3.3-acre inverted five-spot portion of a lenticular body of Robinson sandstone. Net sand was 50 ft thick, porosity averaged 19.7 per cent, oil saturation was 68 per cent of pore volume, and water saturation was 20 per cent of pore volume. The oil in place was estimated at 1,040 bbl/acre-foot, or 171,600 bbl within the 3.3-acre pattern. The water in place was 326 bbl/acre-foot, or 53,800 bbl. The oil has a specific gravity of 28.7° API and a viscosity of 40 cp at the reservoir temperature of 65°F. AIR INJECTION PERFORMANCE Air injection took place in two phases, the phases separated by ignition of the reservoir. In the pre-ignition phase, air injection tests were conducted in the summers of 1960 and 1961. These indicated that the Fry reservoir was confined, and a high return rate of injected air could be expected. This proved to be an outstanding characteristic of the project, as cumulative gas production was 95.3 per cent of the air injected. The difference between the cumulative air injected and the total gas produced can be largely accounted for by the quantity of air stored in the reservoir. An estimated 16 X 10 cf of air remained in the burned-out portion of the reservoir and an indeterminate amount of gas was stored in the unburned but pressurized reservoir. Hence, a complete material balance of gases would account for nearly 100 per cent of the air injected. At times during the test, the daily gas production rate was 98 per cent of the daily air injection rate. Fig. 1 presents the air injection history of the Fry com-

Jan 1, 1966

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939

By S. N. Sharma, William Davis

Because of diminishing energy resources and rising energy costs, every industry is forced to carefully examine its pattern of energy consumption. The copper industry is no exception; current smelting practice begs for technological innovations that would improve the efficiency of its energy utilization. The thermochemical simplicity of copper metal production, as shown in Fig. 1, is deceptive. Designed from the same basic principles, there are four major commercial processes either in use or under construction; and others, such as the Mitsubishi process, are being developed.

Jan 5, 1977

By M. F. COOLBAUGH

WHEN I was asked to speak on the subject of leaching, I did not realize that a complete summary of recent progress in leaching had been given by Stuart Croasdale. I shall try to give some other phases of the subject that were not touched by Mr. Croasdale. Not all metallurgists are in harmony as to their methods of treating metals. If they were it would probably mean lack of progress. They can be divided into two classes-the pyrometallurgists, using fire means, and the hydrometallurgists, or those using leaching methods. Conflict is always good for progress; we have it in politics, and in religion there are fundamentalists, and those who are not fundamentalists. As representing pyrometallurgy, may I hope not to be classed among the fundamentalists. The leaching of ores is not new. The leaching of ores for the recovery of metals, however, is quite new. The older leaching was simply to recover the salts. Agricola, back in 1555, I think it was, outlined a great many methods of leaching for the recovery of salts. They called them solid juices at that time. There was no real competition, however, between leaching meth-

Jan 1, 1926

By H. F. JR. Miller

(Butte Meeting, August, 1913.) THE major cause of the deterioration of the open-hearth furnace as its length of service increases, is the melting down, or rather the slagging, of the checker-brick, together with the deposition of dirt in the form of iron oxide, etc., which helps to close the openings, as well as to slag the brick by chemical action. Any construction that will do away with the necessity of having the waste gases come down through the checkers will eliminate the main reason for their deterioration. There are some other well-defined reasons which are subordinate to the main one given above. Some of the defects of the present type of regenerator chambers are as follows: 1. The checkers cannot be cleaned while the furnace is in operation, nor can they be cleaned at the end of the run without taking out all of the checker-brick. This causes high costs for labor and brick. The labor cost is high because all checker-brick have to be handled twice. The brick cost is high because many of the bricks are spalled in the double handling, rendering them useless because a spalled brick will not stand up. 2. The top courses of brick become coated with iron oxide, etc., melt clown, and large amounts of dirt are deposited throughout the checkers, especially at the bottom. The draft of the furnace is decreased by the closing of the top and bottom openings, especially the top ones, and the entire working of the furnace is affected. If an effort is made to clean the checkers the dirt and brick falling down into the holes still further diminish the draft. 3. The distribution of the air or waste gases through the checkers is in many cases uneven, resulting in a lower temperature of pre-heated air and therefore a slower working furnace. Also, the passage of air and waste gases is so crooked that sometimes the chimney is not powerful enough to overcome the friction.

Jan 6, 1913

By Rudolf Kudlich

The problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Latcr, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines—by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care. It is necessary, therefore, to place our reliance mainly on mechanical devices to prevent accidents, and to depend as little as possible on laws,

Jan 1, 1923

By Rudolf Kudlich

The problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Latcr, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines—by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care. It is necessary, therefore, to place our reliance mainly on mechanical devices to prevent accidents, and to depend as little as possible on laws,

Jan 1, 1923