Search Documents

By R. A. Davidson, L. Silverman

RESIDENTS of many urban centers are becoming increasingly aware of the obscuring effect of fume and smoke discharge from power, metallurgical, chemical, and other industries; and they, as well as the legislatures of these affected cities, are agitating for cleaner air. Management's most pressing problem is to find an economical way to reduce process effluents in response to the growing pressure from population and legislative demands. The removal must be done, if possible, without handicap to the current operation, since the costs of relocating are often excessive or prohibitive. In fume recovery or disposal, an important item to consider is whether or not the material being discharged has any value. If it has commercial value, the cost of its recovery may offset or aid amortization. For this reason, in making a study of the specific problem in hand, a major factor was the nature of the material emanating from the stack: in particular, its particle size, size range, and its chemical and physical composition, as well as its potential value and utility when recovered (in either a wet or dry state). Should the product have no commercial value, it must be disposed of at minimum cost in a way to prevent recontamination. Initial studies were therefore made to determine stack concentrations and volumes of material evolved from the operations. The next phase of the study concerned the physical and chemical nature of the collected fume. The third portion of this paper describes the wet and dry collector studies undertaken to recover the fume. Cleaning Requirements for Ferroalloy Furnace Operation The basic need for any effluent collection equipment is the highest possible efficiency and the lowest tolerable resistance when the power consumption involved is considered. Since the electric furnace effluent is largely composed of fume of small size (less than 0.5u), it has high light obscuring properties, and even low concentrations will cause some loss of visibility and be evident to nearby residents. The permissible limit for fly ash emission in many cities is based on a weight value (viz, approximately 0.4 grains per cu ft), but the smoke density values are dependent upon a shade of color. In the case of the Los Angeles County code, emission is restricted to pounds per pound of material processed per hour basis (but not exceeding 40 lb per hr for any one given plant operation). If an average particle size of the fume from ferro-silicon alloy electric furnaces is assumed to be 0.4u (as shown later, this is the approximate mean size) and an average loading of 1 grain per cu ft (stp), each cubic foot of stack gas will contain approximately 75x10 10 particles (based on assumed, and confirmed, spherical shape and a standard deviation of unity). When it is realized that the air in metropolitan areas, which are also general industrial areas, contains approximately 5x108 particles, the tremendous light scattering effect of this concentration becomes apparent. Consequently, nearly 100 pct collection would be necessary to equal the average concentration. Fortunately, however, discharge from a high point above ground (50 to 100 ft) will result in at least a thousandfold dilution, or the stack concentration reaching the ground in the foregoing case might result in a ground concentration of ' particles. If the concentration at the source could be reduced by a factor of 100 (99 pct efficiency of collection), then a concentration of 75x10" particles would be diluted to 7.5x10' which would be very satisfactory. An efficiency of 90 pct (factor of 10 decontamination) at the source would result in a discharge of 75x109 articles which upon dilution yields 75x10 which is still 15 times the general air value. Another approach to this consideration is to use the value of concentration of 0.005 grains per cu ft for the value of a visible effluent as cited by Kayse.1 To attain this value with an average loading of 1 grain per cu ft would require an efficiency of 99.5 pct. Since the foregoing value is not based on any reported size of fume particles, it is felt that the numbers' approach given previously is more reliable. These calculations serve to indicate the desirability of thorough cleaning, preferably at the source, and with efficiencies well above 90 pct, preferably above 95 pct (dilution 1:20). One of the most important items in any control program is to reduce the concentrations as close to their sources as possible. The use of better furnace design, deeper coverage over the electrodes, and the prevention of blows or breaks in the surface all help to reduce dissemination; consequently, all of these improvements should be made, if possible, to cut down the effluent load. In addition, in order to minimize the volume of contaminated air that has to be cleaned, the furnace should be enclosed as much as possible. Test Arrangements Before fundamental studies with collectors were made, a furnace stack selected for the test program was sampled to determine the gas temperatures and

Jan 1, 1956

YEAR or ELECTION 1913. FRANK DAWSON ADAMS Montreal, Canada. 1933. KARL EILERS New York, N. Y. 1922. FEDERICO GIOLITTI Q. Torino,Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER New York, N. Y. 1931. WALDEMAR LINDGREN Cambridge, Mass. 1921. C. MCDERMID London, England. 1913. EZEQUIEL ORDOAEZ Mexico City, Mexico 1935. ROBERT PEELE New York, N. Y. 1938. A. M. PORTEVIN Paris, France. 1937. Joan V. W. REYNDERS New York, N. Y. 1937. GEORGE S. RICE Washington, D. C. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T. A. RICKARD Victoria, B.C., Canada. 1933 Cambridge, Mass.

Jan 1, 1938

By P. Somasundaran, D. R. Nagaraj

Based on our finding that commercial copper chelating solvent extractants such as LIX65NR and LIX63R are excellent collectors for copper minerals, a detailed study was made using several water-soluble chelating agents belonging to the class of aromatic hydroxyoximes and having a gradual structural variation. A basic study of the system salicylaldoximetenorite was also carried out. Microflotation tests as a function of concentration of oxime, pH, addition of copper, etc., using oxidic copper minerals such as chrysocolla and tenorite, and batch laboratory flotation tests using synthetic mixtures of quartz and oxidic copper minerals were carried out. The results have demonstrated that the hydroxyoximes studied have comparable collector property, and in all cases the oxime was found to be partitioned between the mineral surface and the copper in the bulk aqueous phase in the form of a bulk copper chelate. The occurrence of the latter could be accounted for by formation in the bulk phase of a chelate between oxime and copper released from the mineral and/or by the detachment of the surface chelate. The role of surface and bulk chelates in flotation is discussed based on the results of partitioning of chelating agent into bulk and surface chelates in the salicylaldoxime-tenorite system. The effect of structural aspects such as isomerism and substitution in the molecule on the collector property of the oximes is also discussed. Substitution on oximic carbon by alkyl groups is found to promote collector activity. Only the anti-isomer has the ability to collect.

Jan 1, 1982

Chairman, MRS. JESSE SCOBEY The Foreign War Relief Committee closed its dispensary fund during the past month with a contribution to the American Fund for French Wounded of $1720.51, balance on hand, principal and interest, as a gift from the New York Section of the Woman's Auxiliary for pressing emergency dispensary work in France. The American Fund for French Wounded was authorized to cable this sun at once, in consideration of the fact that their existing dispensaries, including the one established by the New York Section at Briey, were in excellent condition, while their mobile dispensary fund was confronted by the most urgent need for work among the refugees now returning in pitiable condition and in great numbers to certain distressing centers. The committee sewing at Fund headquarters every week has had seven working days, with an enrollment of twenty: The average attendance was ten; largest attendance for any one day, thirteen; smallest attendance, eight. Interest in this activity is growing steadily and it is the intention of the committee to push the work vigorously for the next few weeks.

Jan 3, 1919

By H. E. Elliott, R. S. Busk, A. T. Peters

ONE of the problems of the fabricator of metals and alloys is the propensity of some composition ranges toward abnormal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, o per cent Al, 2 per cent Zn, 0.2 per cent Mn) and G alloy (Mg, i0 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other metals. Jeffries and Archer' have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. of abnormal local grain growth was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. r) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The Dow Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germination," since this term has been defined' as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

A group of prominent engineers and contractors of Chicago and vicinity have cooperated in forming a Joint Committee on Military Engineering. The founders are members of all of the leading engineering and contracting organizations of Chicago, including the local branches of the national engineering societies. The purposes of the Committee are to further military preparedness among engineers, contractors and their associates by the following means: (1) Courses of lectures; (2) assigned reading; (3) studies and practical instruction in military engineering;. (4) assisting engineers to qualify as officers in the National Reserve Corps of Civilian Engineers; (5) urging enlistment in and support for engineer troops of the National Guard and such other organizations as the Government may create; (6) furthering instruction in military engineering in training camps and the attendance in them of those qualified; (7) by such other means as from time to time may be deemed advisable. The Joint Committee has already prepared a program covering the vital points outlined. To date the program is practically complete for a period extending from April 20 to July 25. Something of interest will be taken up each week, including lectures by Lieutenant-Colonel W. B. Judson, Engineer Corps, U. S. Army; two lectures by Major P. S. Bond, Engineer Corps, U. S. Army; Lieutenant-Colonel Mason M. Patrick, Engineer Corps, U. S. Army, and several exhibition drills, terrain exercises and inspection trips under the direction and guidance of various officers of the Engineer Troops of the Illinois National Guard. Additions to the program will be made from time to time. '

Jan 5, 1916

By F. G. Jones, R. D. Pehlke, H. E. Gardner

The solubility of nitrogen in liquid Fe-18 pct Cr-8 pct Ni-0. 7 to 2.3 pct A1 alloys has been measured up to the solubility limit for the formation of aluminum nitride in the temperature range 1600° to 1700°C uszng the Sieverts' method. The solubility of nitrogen in 18-8 stainless steel increases with increasing aluminum content. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from the elements dissolved in liquid 18-8 stainless-steel alloys has been determined to be: ?G° = -42,500 + 20. IT in the range from 1600° to 1700° C. EVANS and pehlke1 have measured the equilibrium conditions for the formation of aluminum nitride, AlN, in liquid Fe-A1 alloys. The present study extends that work to the more complex solvent, liquid 18 pct Cr-8 pct Ni (18-8) stainless steel. Recent work by Small and pehlke2 has dealt with the effect of fourth-element additions on the solubility of nitrogen in 18-8 base alloys. They found the effect of aluminum additions, up to 0.74 pct, on the solubility of nitrogen to be small. The present study covered the range from 0.74 to 2.28 pct aluminum, and by extending the composition range may be used to better define the effect of aluminum on the nitrogen solubility in these alloys. EXPERIMENTAL PROCEDURE The Sieverts' method was used to measure the equilibrium solubility of nitrogen gas in liquid 18-8 stainless steel alloys containing 0.74, 1.49, 1.93, and 2.28 pct Al. The solubility was measured as a function of the nitrogen gas pressure at temperatures of 1600°, 1650°, and 1700°C. The apparatus used is the same as described by Small and Pehlke.2 The 100-g melts were made from Ferrovac-E high-purity iron, Crucible Steel Co.; 99.95 pct Cr, Union Carbide Corp.; 99.9 pct Ni, International Nickel Co.; and 99.99+ pct Al, Aluminum Co. of America. The aluminum was charged at the bottom of the crucible, surrounded by nickel and iron. The chromium was packed into the interstices to minimize vapor transport of the aluminum during initial melting. The hot volume of the system, measured for each melt with argon, ranged from 45 to 55 standard cu cm with a temperature coefficient of —8 x 10-3 cu cm per °C. The melt temperature was measured with a Leeds and Northrup disappearing-filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature calibration of the system by Small and pehlke2 was assumed. Two problems are involved in determining the solubility product of a solid, metal nitride phase in liquid iron alloys. These are: 1) establishing the point of departure from Henrian behavior at the solubility limit of the metal nitride phase; and 2) determining the composition of the solid nitride which is precipitated. Determination of the solubility product of AlN was made by admitting small amounts of nitrogen into the reaction bulb until the deviation from Sieverts' law was clearly evident in the form of a pressure halt. To obtain the solubility product at several temperatures during one run the following procedure was used: 1) add increments of nitrogen to determine the Sieverts' law line at the lowest desired temperature; 2) continue to add nitrogen to precipitate a small amount of the nitride phase; 3) increase the melt temperature 50°C to dissolve the precipitated nitride; 4) repeat step 2 until either a nitride formed or the system reached ambient pressure; if a nitride formed at 1650°C, the sequence was repeated at 1700°C. The composition of the precipitated phase was checked by an X-ray diffraction pattern obtained from powder scraped from the surface of the solidified 1.93 pct A1 melt. RESULTS AND DISCUSSlON Solubility Measurements. Fig. 1 is a typical nitrogen-absorption curve obtained from measurements on a 1.93 pct A1 alloy. Since the initial absorption of nitrogen follows Sieverts' law the nitrogen solubility is plotted as a function of the square root of the pressure of nitrogen gas in the reaction bulb. The results of the solubility measurements for all alloys studied are summarized in Table I. The slope of the Sieverts' law line for each alloy was determined. Since this is also the solubility of nitrogen at 1 atm pressure of nitrogen gas, the latter designation is used for the data. It should be noted. however, that in most cases the value lies above the solubility limit for AlN. Fig. 2 shows the effect of aluminum on the solubility of nitrogen at this reference pressure and as a function of melt temperature. The solid portions of the lines represent attainable solutions; the dashed regions lie above the limit for precipitation of AlN.

Jan 1, 1969

By Persifor Frazer

The section along the left bank of the Susquehanna, in Lancaster County, from Falmouth to the Maryland line, which the writer made in 1877 to accompany his report on that county, was redrawn by Professor Lesley, as stated in the prefatory'letter to Vol. CCC. (p. x.).* As then stated, neither the numerous data, nor the general features of the structure obtained by the writer, were changed ; but enough was done to make a discrepancy between the text and the section as given; and some important points were made less clear in the published section than they were in the MS. map. Amongst other portions of the section, that between the railroad stations, 1190 to 1224, gives the impression on the published maps of a much too definite superposition. A few words will be devoted to this region in the following communication. There is absolutely no room to doubt the structure for about four miles on .each side of the Tocquan axis. The dips are gentle, and in opposite directions, and the lithological characters constant within ordinary limits of variation, nor do these characters resemble those of the rocks which flank these gneisses and mica schists to the northwest and the southeast. For the same reasons it is evident that the rocks which occur within these eight miles or so, represent an horizon below the basement of the fossiliferous or palaezoic series. Not only have no fossils been found, but their lithologieal characters are unmistakably eozeic. But on the upper and lower margins of this

Jan 1, 1884

A group of prominent engineers and contractors of Chicago and vicinity have cooperated in forming a Joint Committee on Military Engineering. The founders are members of all of the leading engineering and contracting organizations of Chicago, including the local branches of the national engineering societies. The purposes of the Committee are to further military preparedness among engineers, contractors and their associates by the following means: (1) Courses of lectures; (2) assigned reading; (3) studies and practical instruction in military engineering;. (4) assisting engineers to qualify as officers in the National Reserve Corps of Civilian Engineers; (5) urging enlistment in and support for engineer troops of the National Guard and such other organizations as the Government may create; (6) furthering instruction in military engineering in training camps and the attendance in them of those qualified; (7) by such other means as from time to time may be deemed advisable. The Joint Committee has already prepared a program covering the vital points outlined. To date the program is practically complete for a period extending from April 20 to July 25. Something of interest will be taken up each week, including lectures by Lieutenant-Colonel W. B. Judson, Engineer Corps, U. S. Army; two lectures by Major P. S. Bond, Engineer Corps, U. S. Army; Lieutenant-Colonel Mason M. Patrick, Engineer Corps, U. S. Army, and several exhibition drills, terrain exercises and inspection trips under the direction and guidance of various officers of the Engineer Troops of the Illinois National Guard. Additions to the program will be made from time to time.

Jan 5, 1916

Here, published for the first time, is the group of Anaconda officials (New York office) concerned with the planning and operations of the company's copper properties in Chile.

Jan 1, 1952

By Olin G. Bell

At the beginning of the year 1935 the older fields in Southwest Texas, and particularly those discovered during 1934, had been practically delimited and only normal development continued. As a result, operations in this area were somewhat slowed down. Shortly after the first of the year, however, activity in the area was greatly accelerated, due largely to the fact that the Loma Novio field, discovered during the last few days of 1934, indicated the presence of a new productive trend east of and parallel to the Government Wells field and also indicated the presence of a new productive horizon, the Loma Novio sand, approximately 100 ft. lower than the Government Wells sand zone. Other discoveries during the year greatly augmented the activity in the district. During the year there were 651 oil wells, 53 gas wells and 275 dry holes drilled in this area during the year. Most of the operations were in the Government Wells, Cole, Loma Novio, Seven Sisters and Lopez fields. New Fields Four new fields were discovered during 1935 as follows: Seven Sisters and Piedra de Lumbre in Duval County; Loma Alto in McMullen County; and Lopez in Webb County. Seven Sisters Field.—The Seven Sisters field, opened in May, was the direct result of a systematic search for new productive areas northeast of the Loma Novio field. The first producer, Harvey & Henderson NO. 1 Chernosky, survey 226, was completed in the Labbe (Chernosky) sand at 2220 ft. However, the second producer, Santa Clara Oil Co. No. 1 Welder in survey 385, drilled about one mile south of the discovery well, failed to find production in the Labbé sand and was carried on down and completed in the Government Wells sand at 2473 ft. with an initial production of 20 bbl. of oil per hour. These two discoveries, in the Labbé and Government Wells sand, started an active leasing and drilling campaign in this part of Duval County and drilling operations continued especially active throughout the remainder of the year.

Jan 1, 1936

By Olin G. Bell

At the beginning of the year 1935 the older fields in Southwest Texas, and particularly those discovered during 1934, had been practically delimited and only normal development continued. As a result, operations in this area were somewhat slowed down. Shortly after the first of the year, however, activity in the area was greatly accelerated, due largely to the fact that the Loma Novio field, discovered during the last few days of 1934, indicated the presence of a new productive trend east of and parallel to the Government Wells field and also indicated the presence of a new productive horizon, the Loma Novio sand, approximately 100 ft. lower than the Government Wells sand zone. Other discoveries during the year greatly augmented the activity in the district. During the year there were 651 oil wells, 53 gas wells and 275 dry holes drilled in this area during the year. Most of the operations were in the Government Wells, Cole, Loma Novio, Seven Sisters and Lopez fields. New Fields Four new fields were discovered during 1935 as follows: Seven Sisters and Piedra de Lumbre in Duval County; Loma Alto in McMullen County; and Lopez in Webb County. Seven Sisters Field.—The Seven Sisters field, opened in May, was the direct result of a systematic search for new productive areas northeast of the Loma Novio field. The first producer, Harvey & Henderson NO. 1 Chernosky, survey 226, was completed in the Labbe (Chernosky) sand at 2220 ft. However, the second producer, Santa Clara Oil Co. No. 1 Welder in survey 385, drilled about one mile south of the discovery well, failed to find production in the Labbé sand and was carried on down and completed in the Government Wells sand at 2473 ft. with an initial production of 20 bbl. of oil per hour. These two discoveries, in the Labbé and Government Wells sand, started an active leasing and drilling campaign in this part of Duval County and drilling operations continued especially active throughout the remainder of the year.

Jan 1, 1936

By L. G. Austin, R. R. Klimpel

This communication points out that serious errors exist in some current treatments of the random fracture of solids, including the prior treatments by Klimpel and Austin, Gilvarry, and Gaudin and Meloy. The problem considered in all of these papers is: what cumulative weight versus size distribution is expected for the fragments produced by fracture of a particle? The basic assumption made is that fracture surfaces propagate in random directions from weak flaws in the solid (these weak flaws being activated to fracture by applied stress), with the activated weak flaws distributed at random spatially within the solid. The previous treatments considered fracture in three dimensions, and all use similar physical models, although the mathematical techniques were somewhat different. We first noticed that these treatments were in error when we attempted to reduce the equations developed to the simple case of fracture of a one-dimensional particle, e.g. a long, thin fiber which breaks along its length. For this simple case, it is readily shown that the assumption of random fracture leads to the expression P(V) = (r/Vo) (1-V/Vo) r-1 dV (1) is the probability of occurrence of a fragment of length within the range V to V + dV; V being length dimension, from r random fractures passing through an original size of Vo to produce r + 1 fragments. This equation agreed with the one-dimensional form of an equivalent equation in the original Klimpel-Austin treatment. However, in this treatment it was then stated that, "The fractional weight below size V is [ ]

Jan 8, 1968

[YEAR OF ELECTION 1913. FRANK DAWSON ADAMS Montreal, Canada 1938. HENRY CORT HAROLD CARPENTER London, England 1933. KARL EILERS New York, N. Y. 1922. FEDERICO GIOLITTI Torino, Italy 1906. SIR ROBERT A. HADFIELD London, England 1921. FRANK WILLIAM HARBORD London, England 1917. HERBERT HOOVER York, N. Y. 1939. HENRY KRUMB New York, N.' Y. 1921. C. McDERMID London, England 1913. EZEQUIEL ORDONEZ Mexico City, Mexico 1935. ROBERT PEELE New York, N. Y. 1938. A. M. PORTEVIN Paris, France 1937. JOHN V. W. REYNDERS New York, N. Y. 1937. GEORGE S. RICE Washington, D. C. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T. A. RICKARD Victoria, B.C., Canada]

Jan 1, 1940

By N. Tiner

IN an article on magnesium and its alloys, Gann and Winston1 stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 695°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I): This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing o.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. EXPERIMENTAL METHOD The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945

By Marsh S. Watson, Robert A. Howard

The effect of depth of formation penetration by casing perforations has been studied by means of an electrolytic model. It is found that the relative productivity of perforated casing is profoundly affected by the depth to which the formation is penetrated. The first in. of penetration i: of especial importance. A scaling equation which was shown to agree with experimental results at zero penetration is used to calculate the relative productivity of a waled down casing with scaled down perforations. INTRODUCTION In an earlier piper' the authors showed that the point sink representation of casing perforations is inade- quate. It was Pointed out at that time that while the electrolytic model results were a marked improvement over point-sink calculations, they still left a great deal to be desired in that the electrolytic model represented a case not realizable in practice, namely, a clean hole through the casing but undisturbed formation on the other side of the casing. Obviously, to be effective, the perforation must penetrate a finite distance into the producing formation. It was the purpose of the present investigation to find how the relative productivity of perforated casing varies with depth of penetration. The term "depth of penetration" as used in this paper refers to the distance which the perforation penetrates the producing formation. The amount of casing and cement penetrated is not taken into account, a fact which is discussed more fully later. The "casing radius," therefore, is to be interpreted as the radius of the boundary between cement and formation wall. in cases where the casing is not in contact with the formation wall. APPARATUS The electrolytic model experimental setup was identical with that described in the previous paper' except that the platinum electrodes were now allowed to project from the lucite cylinder by varying amounts. When fewer than eight electrodes were used, the unused ones were covered with a coat of insulating material to minimize disturbances to the current flow-lines. Comparison runs made with the unused electrodes uninsulated, however, showed that the values of Q/Q0 so obtained did not vary by more than the experimental error from the values obtained with the unused electrodes insulated RESULTS The variation of relative productivity* with perforation density is shown for various penetration depths from 0 to 4.03 in. in Fig. 1. It will be seen that even one in. of penetration into the formation results in a huge increase in the relative productivity. Moreover, as-the depth of penetration increases, it becomes less and less advantageous to use large perforation densities, 80 pel. cent of open hole productivity being obtained with only three 0.5-in. diameter holes per foot when the penetration is 4.03 in.

Jan 1, 1950

By R. M. Stewart, C. W. MacQueen

Anaconda's Berkeley pit at Butte produces 34,000 tpd of ore averaging 0.8 pct copper. Two-and-one-half tons of waste is stripped per ton of ore, approximately 40,000 tpd by the company and an added 45,000 tons by the F&S Contracting Co. The company truck fleet consists of 24 Euclid and 18 Mack 34-ton, rear-dump diesel trucks.

Jan 7, 1961

By Francis Foley

WITH the possible exception of high-speed tool steel, the service demanded of rock-drill steel is probably more precarious than that of any other tool steel. Unaided by the helpful influence of alloys and dependent solely on the efficiency of the heat treatment applied for its ability to stand up under the abuse to which it is necessarily subjected, rock-drill steel is worthy of intensive study. For its heat treatment the smith has his fire, an oil fire perhaps, and a quenching bath; he judges' the temperature by his eye. There are shops where excellent drills are produced by this method, but there are more where the product varies between very good and very bad. Pyrometers with specially designed equipment are used in but few cases. But the responsibility for rock-drill failures does not rest entirely on the smith. Little has been published concerning the efficiency of drill steel, though the Canadian Mining Journal' published the breakage record of a large number of hollow drill steels. This record indicates that most of the breaks occur during the early life of the steel and that as a given batch of steel is used, its percentage of breakage decreases. This fact, the article points out, is at variance with the much-talked-f theory concerning failure from crystallization and fatigue. It seems to point to the fact that the greater part of drill-steel failure from breakage is traceable to faulty manufacture, resulting in defects in the bore of the hollow steel from inclusions of slag or oxides, etc. As this defective material meets with early failure, it is weeded out. In addition, some breakage may be caused by a lack of proper condition with respect to heat treatment of the steel as furnished by the manufacturer. In the article mentioned, the breakage of 1 ¼ -in. (3.17 cm.) hollow steel is given as 4.62 per cent. for the early period of use, with a decrease to 3.35 per cent. and 2.67 per cent. With time in use. For 1-in. (2.5 cm.) hexagonal hollow steel, the figures for breakage are 0.18 per cent. and 0.06 per cent.; attention is called to the "enormous decrease in breakage by the use of smaller diameter drills." The figures are given as so many "drills sharpened," but there is no way of determining the percentage of

Jan 6, 1921

By D. M. Urich

New plant construction for pyrolysis and agglomeration during 1969 has been relatively quiet in the North American scene. U.S. pellet capacity approximates 52 million long tons and that of Canada 25.3 million tons. The foreign scene, however, has been extremely active during 1969, and this is expected to continue for the next several years. Changes in sinter practice have not been reported, other than a few changes towards increased bed depths and the increased use of screening facilities to size the product more closely. Interest in the field of briquetting in fields other than iron ore is high with a new fluorspar briquetting plant under construction at Brownsville, Texas. Considerable research appears to be pointed towards solving the problem of reclaiming steelmill waste products (flue dust, BOF dust, mill scale) by means other than sintering.

Jan 1, 1970

By Y. C. Liu, W. R. Hibbard

An aluminum single crystal cold-rolled from (110) [1121 essentially retains its initial orientation after 99.6 pct reduction in thickness. The orientation of the recrys-tallized grains of this material can be described in terms of crystallographic rotations about principal poles of deformation texture. DURING the study of the recrystallization of a copper single crystal cold-rolled from a (110) [112] initial orientation, the orientation of the re-crystallized grains could be derived by a 30" rotation of the orientation of the cold-rolled matrix about its <111> poles.&apos; The present investigation was undertaken to extend the work done on copper&apos; to an aluminum crystal also cold-rolled from a (110) [112] initial orientation. Experimental Procedure The procedure of this experiment was similar to that reported for copper.&apos; An aluminum (99.998 pct) single crystal rod* 1 % in. in diameter was grown in back-reflection technique.&apos; The specimen (1.20x 1.004x0.6787 in. thick) was then rolled along the [112] direction. The final thickness was 0.0028 in., giving a reduction in thickness of about 99.6 pet. Specimens were cut from the rolled strip with scissors, and approximately in. of disturbed metal was removed with Tucker&apos;s reagent. The rolling edge remained intact. The specimens were sandwiched between two graphite plates and annealed in a lead or lead alloy bath which was electrically heated. Pole figures were constructed using the techniques previously described.&apos; Specimens were electrolytically polished4 and etched with 47 pct HNO8, 50 pct HC1, and 3 pct of 48 pct HF. The electrolytic polishing method and etching reagent employed for aluminum specimens were not entirely satisfactory and the microstruc-tures could not be studied in any detail. Results and Discussion The octahedral pole figure of cold-rolled aluminum strip is plotted in Fig. 1. The <111> poles spread in the transverse direction approximately 8" for the highest intensity areas. The spread in the transverse direction can be related to a rotation about two <110> directions lying in a plane containing the rolling direction and rolling plane normal. The two <110> directions and a scale of rotation for the <111> poles are shown in Fig. 2. The amount of rotation is consistent for three of the four <111> poles, about 35" to 40". The discrepancy for the fourth pole is believed to be due to limitations of the film technique. Alternate inter-

Jan 1, 1956