Search Documents

Jan 1, 1958

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,' is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3' tests, however, this is not justified, and the D values

Jan 1, 1941

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,' is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3' tests, however, this is not justified, and the D values

Jan 1, 1941

By F. Keller, R. H. Brown

BECAUSE of the extensive use of Alclad 24s alloy sheet in aircraft construction, there is much interest in the metallurgical changes caused by heat-treatment of this product.1,2 One of these changes is the result of the diffusion of soluble elements from the core into the coating during treatment. This paper deals with the thermal treatments that may influence diffusion and with the practical effects of diffusion on the serviceability of the product. As is well known, Alclad 24s-T sheet has a core of high-strength alloy combined with surface layers of relatively pure aluminum. The microstructure of a cross section of this product is shown by Fig. I. hot only does the relatively high-purity coating have a high resistance to corrosion, and hence serves as a mechanical barrier between the core metal and the corroding environment, but in addition this coating I exerts electrochemical protection over areas where the core may be exposed, such as cut edges. In addition, the coating affords electrochemical protection to projecting heads of *417S-T, 17S-T and 24S-T rivets, or attached members made from these alloys. Under some conditions of heat-treatment, however, diffusion of copper into the coating will alter the electrochemical relationship between the coating and the core to the extent that only partial protection will be obtained under some corrosive conditions. The reason for the electrochemical protection lies in the fact that the coating layers of pure aluminum are anodic to the alloy core. The addition of copper to aluminum produces alloys in which the potential is lower than that of the pure metal. Moreover, as the amount of copper in solid solution in z4S alloy is increased, the potential of the alloy becomes more cathodic. When heat-treated at 920°F. and quenched in cold water, 24s-T is about 0.16 volt cathodic to pure aluminum. However, copper will diffuse from the core into the coating, and if it reaches the surface the potential will be altered in a cathodic direction. Thus the potential dif-erence between the core and coating may be less than 0.16 volt, depending upon the thickness of the coating, and the time and temperature of heat-treatment. Of the methods available for determining the extent of diffusion of copper from the core into the coating of Alclad 24S-T, two are generally used; namely, the metallographic and the solution potential method.3 METALLOGRAPHIC METHODS Metallographic methods will reveal the progress of diffusion of copper into the coating. For instance, the diffusion zone in the coating intermediate between the coating surface and the core is shown in Fig. I. This photomicrograph is of a polished and etched cross section of 0.040-in. Alclad 24S-T sheet. Diffusion proceeds into the coating more rapidly along the grain boundaries than through the body of the grains. consequently, the diffusion zone is not of uniform width

Jan 1, 1944

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

THE subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for 10 years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. I). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, nonmetallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to 100 mg. per sq. cm. per day, the corrosion rate of high-purity magnesium is 0.15 ± 0.05 mg. per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in combination, in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called "tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable. In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0.001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. While the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1941

PRESIDENT OF THE COUNCIL. JOHN HAYS HAMMOND NEW YORK, N. Y. (Term expires February, 1909 ) VICE-PRESIDENTS OF THE COUNCIL SAMUEL B. CHRISTY BERKELEY, CAL. JOHN A. CHURCH NEW YORK, N.Y. PERSIFOR FRAZER PHILADELPHIA, PA. (Term expires February, 1909 ) J. PARKE CHANNING NEW YORK, N. Y. FREDERICK W. DENTON PAINESDALE, MICH. JOHN B. FARISH New York, N. Y. (Term expires February, 1910)

Jan 1, 1910

By AIME AIME

THE American copper mining industry is threatened with disintegration and destruction. This threat is not one which may only materialize in the distant future. The destruction has already commenced. At present, many domestic mines have already closed down. .Others are operating on a greatly curtailed basis. Those operating are doing so only at tremendous loss-because the selling price of copper is below the cost of production and rapidly diminishing financial resources and credit clearly forecast the early suspension of operations in most of the industry. Unemployment in the mining districts is increasing by leaps and bounds. While this condition is due in some measure to the present unsatisfactory state of business in general, the copper industry, unlike other lines of business, sees no possibility of recovery without definite aid. The fundamental, underlying cause of present conditions in the American copper mining industry is the unprecedented rise in foreign production, and the basic change which has taken place in the world copper industry in the last three years. The American industry had begun to feel this change early in 1929 long before the general collapse of business in the fall of that year. While the distress in the industry is undoubtedly aggravated by the present economic depression, it nevertheless would have arrived and. have been present at this time, regardless of general business conditions.

Jan 1, 1932

Our merchant marine is rapidly outgrowing our consular service, according to Edward N. Hurley, Chairman of the United States Shipping Board, who urges that steps be taken immediately to provide facilities abroad for handling the millions of tons of shipping which will be afloat under the American flag in peaceful trade when the war is over. When peace is restored and our present tonnage is scattered over world trade routes, the consular service will be inadequate to handle our ships: Besides, it will have to work against the handicaps of obsolete shipping regulations and, in many cases, lack of experience. There are nearly 100 pages in the United States consular regulations dealing with shipping platters. . Many of these regulations are based on old treaties and many of them are obsolete. There are also differences between treaties with various countries. Our consuls often lack authority to handle matters involving the interests of our sailors and shipowners. Before we can operate a modern merchant marine we must revise, standardize, and simplify this whole mass of regulations and bring them up to the efficiency of other nations' practice.

Jan 12, 1918

By F. L. Wolf

THERE is a tendency on the part of practical foundrymen to accept with reluctance the results of tests on sands, binders, and. such materials made in the chemical laboratory alone. They feel that such tests frequently emphasize and measure properties that are of minor importance and fail to take account of characteristics that are important in determining the value of the material in actual practice. Experience seems to indicate that the most thorough and conclusive, test for any new foundry material is an actual run in the foundry alongside of a standard material of known value. Such a test, however, involves certain difficulties and necessitates certain precautions. It is not always easy to obtain a fair trial for a new material. We all have certain prejudices, which unconsciously affect our judgment to a marked degree. A practical test frequently involves so many workmen, each of whom reacts in a different manner to the test, that; the personal equation becomes very, complex and the true results of the test are obscured. There are times, too, when a thorough experimental trial of a material would interfere too much with the rush of work in a department or would hazard the quality, of the product to such an extent as to make it inadvisable. Under such conditions a laboratory test is advisable before the material is sent into the foundry. These tests should be made as practical as possible and so closely related to foundry practice as to give a true index to the value of a, product for the purpose desired. Core sands and molding sands are as numerous "as the sands of the sea" and vary as much in quality. Old sources of supply are continually failing and new ones must be opened, so that we must continually search for new and better grades of sand. During the past year, the Ohio Brass Co. has developed tests for sands', cores, and binders which bear a close relation to the particular use to which these materials are put in

Jan 9, 1920

By F. C. Holden, R. D. Buchheit

In the course of studies made on the Ti-Cu alloy system,' particles identified visually as TiH were encountered unexpectedly in a specimen of high-purity Ti-0.8Cu alloy. The particles did not appear immediately after preparation, but following-storage in a dessicator for several days. Since the alloy had been vacuum annealed to a low hydrogen concentration (19 ppm by vacuum-fusion analysis), the appearance of the TiH particles was suspected as a surface contamination effect. A specimen of a Ti-0.8Cu alloy had been annealed 2 hr at 790°C and water quenched, to produce the single-phase equiaxed a structure. The metallo-graphic sample was ground through 600X paper, rough-polished on a high-speed wheel with a mixture of alumina and chromic acid, awLhish-polished on a slow-speed wheel. Disturbed metal layers were removed from the final surface by alternately etching with a 1 1/2 HF-3 1/2 HNO3-95 H2O solution and polishing on the slow-speed wheel with fine alumina. The final surface was swab-etched with a 1 1/2 HF-3 1/2 HNO3-95 H2O solution, rinsed in tap water, and dried in a stream of filtered air. The micro-structure, shown in Fig. 1, was composed of equiaxed a grains without any trace of second phase. After storage in a dessicator for 3 days, the appearance of small particles in the structure became evident (see Fig. 2). After 7 days of storage, the particles were more distinct, and in some grains, began to appear as elongated particles. The specimen then was etched a second time (without repolishing) to produce the structure shown in Fig. 4. On the basis of micro- structural observation, the line markings were identified as TiH; attempts to obtain diffraction patterns from the surface for positive identification were not successful. That the structure is a surface effect was demonstrated by grinding with 240X paper to remove the surface layer. The surface then was ground, polished, and etched using the procedures described previously. The same observations were made: the freshly prepared surface was devoid of any second phase, whereas the particles again appeared after several days storage. The same effect has been observed in other a-stabilized titanium alloys, including a high-purity Ti-0.20 alloy containing only 16 ppm H by analysis. The effect has not yet been observed in unalloyed titanium, nor does its appearance appear to be consistent with any particular alloy system. From these observations, it is concluded that certain a-titanium alloys are susceptible to the formation of titanium hydride at the surface of metallo-graphic specimens. The hydrogen probably is diffused into the surface from a residual film of etchant decomposition products. Estimates of the hydrogen

Jan 1, 1961

By Harold B. Ewoldt, Robert R. Reynolds

THE Upper Mississippi Valley zinc-lead district covers an area of some 2000 sq ml located in the southwestern corner of Wisconsin, the north-western corner of Illinois and a portion of eastern Iowa around the city of Dubuque. Commercial deposits of lead and zinc have been mined in Iowa but the major discoveries during the past eight years have been made in Jo Daviess County, Ill, and LaFayette County, Wis. Activities in the state of Illinois are centered about the city of Galena, while those in Wisconsin are located a few miles south and west of the town of Shullsburg.

Jan 3, 1951

By John V. Beall

As recently as 1964, the situation in the Australian iron ore industry was chiefly one of potential. The only producer was the Broken Hill Pty. (BHP). That company mined about 5 million tpy from deposits in the Middleback Range in South Australia and at Yampi Sound in Western Australia. No ore was exported from Australia. Now, just five years later, and after expenditures amounting to approximately one half billion dollars, BHP and seven new companies exported about 15 million tons (long tons) of iron ore and pellets as well as meeting Australia's own annual requirements of approximately 8.5 million tons of ore. Early this year, the volume of iron ore on order stood at 328 mil- lion tons to be delivered over a period of 15 years, but Cliffs Western negotiations for sale of Robe River iron ore have boosted the volume to the new high of 466 million tons. All of this has meant a great deal to Australia in terms of new income. In fiscal year 1967 (ending June 30, 1967) exports of iron ore amounted to $52 million; in 1968, $128 million and by 1'972 the Bureau of Mineral Resources expects the value of exports from iron ore to reach $242 million. In achieving the position of major- supplier of iron ore to the Japanese steelmakers, it was necessary to build a great many new facilities, mostly in Western Australia. Three railroads, 70 miles long, 182 miles and 265 miles were constructed. A new port was created at Dampier; Port Hedland was deepened and otherwise improved; both of these ports are in Western Australia. In Tasmania, Savage River developers built an offshore shiploading station that has received the recognition of engineers internationally. At least a half dozen new communities have been founded. The narrow gage railroad from Kalgoorlie to Perth and Freemantle was replaced with a standard gage line.

Jan 6, 1969

By J. B. Conway

Stress-vuptuve data for several of- the refractory metals are frequently found to yield a linear relationship between the Larson-Miller parameter and the logarithm of the applied stress. In such cases linear stress-rupture isotherms result with slopes bearing a definite relationship to the temperature. It also follows that the stress to produce rupture in a certain period of time will be linear in temperature. Data for several refractory metals have been reviewed and excellent linearity is shown in this type of isochronal plot. In addition, the af ore - mentioned lineavity leads to a linear relation between the log of the stress to produce rupture in a certain time and the homologous temperature. This has been illustrated for the Group VI-A metals, tungsten and molybdenum. EXTENSIVE use has been made of the Larson-Miller' parameter in the interpolation and extrapolation of stress-rupture and creep data. In those cases where this particular parametric approach is applicable a convenient and fairly straightforward procedure is made available for the correlation of experimental stress-rupture data. It is quite common to employ this parameter in the form of a master rupture plot in which the parameter, T(C + log tr), is expressed as a function of log stress. In many cases this functional relationship in log stress is linear within acceptable accuracy and hence the following relation results: where P is the parameter, C is the Larson-Miller constant, T is the absolute temperature, t~ is the rupture time, a is the stress, and a and b are constants. Examples of such a relationship are contained in the work of Green, Smith, and 01son2 dealing with high-temperature rupture behavior of molybdenum and in the work of Green' dealing with the high-temperature behavior of tungsten. In addition, pugh4 has shown a similar linearity for some fairly low-temperature data for molybdenum. It can be shown that when the relationship in Eq. [I] is exhibited certain generalizations can be made concerning the form of the stress-rupture isotherms. For example, rearranging yields: For a given material (constant C) at a given temperature the first term on the right-hand side of Eq. [2] is a constant and hence this equation defines a straight line when log stress is plotted as a function of log-rupture time. This is recognized as the standard form usually employed in this type of data presentation. Such linearity then suggests the linear form of the Larson-Miller parameter. Or, in other words, the linear parametric relationship in Eq. [2] results only when the stress-rupture data are linear on a log-log plot of stress vs rupture time. Another interesting observation can be made in regard to Eq. [2]. It can be noted that the slope of the stress-rupture isotherms is given by - T/b and hence a direct calculation of the constant b is available. It also follows that since the value of b is the same for all temperatures the slopes of the various isotherms on the log-log stress-rupture plot cannot be the same. Indeed, the existence of the relationship in Eq. [2] precludes a system of parallel lines on this common stress-rupture plot. As a matter of fact it further specifies that in addition to being nonparallel the slope of these isotherms must decrease (i.e., become more negative) with increasing temperature. Such a condition is indeed found to exist in the case of the stress-rupture data reported for molybdenum.' As a corollary to the above, it may be stated that stress-rupture data which do not lead to a linear log-log stress-rupture plot or whose isotherms do not exhibit a decrease in slope as the temperature increases will not yield the linear relationship of Eq. [I]. Applying Eq. [2] to two different temperatures and solving for C yields: Eq. [3] affords a simple and rapid method for calculating the Larson-Miller constant from the log-log stress-rupture plot. The slope of a given linear isotherm is measured and the value of "b" calculated based on Eq. [2] as: slope = - -Tb Then at an abscissa value of 1.0 hr (making log tr in Eq. [3] equal to zero) read the stress corresponding to rupture for two different temperatures. Substitution in [3] yields: A value of the Larson-Miller constant can thus be calculated from a few simple mathematical procedures employing data read directly from the log-log plot of the stress-rupture data. Of course, it is not to be overlooked that the above reasoning has been based on the linear relationship of Eq. [I] being applicable. However, if as mentioned above the log-log plot is

Jan 1, 1967

By K. J. Gill, P. Chiotti, J. T. Mason

Thermal, metallographic, and vapor pressure data were obtained to establish the pkase boundaries and the standard free energy, enthalpy, and entropy of formation for the compounds in the Y-Zn system. Three coinpounds with stoichiometric formulas of YZn, YZn2, and Y2Zn17 melt congruently at 1105", 1080°, and 890°C, respectively. Four compounds with stoiclziometric formulas of YZn3, YZn4, YZn5, and YZn,, undergo perztectic reactions at 905", 895", 870º, and 685ºC, respectively. Three eutec-tics exisl in this system with the .following eutectic temperatures and zinc contents in wtpct: 875ºC, 23.2 Zn; 1015ºC, 51 Zn; 865ºC, 82 Zn. The YZn, pkase undergoes an allotropic transformation. In the two phase YZn2 -YZn alloys the trans.formation gives a weak thermal arrest at 750°C, whereas in the two phase YZn2-YZn3 alloys no thermal arrest is observed and the transformation occurs over a temperature range below 750°C. At 500°C the free mzergies of formation per lnole vavy from —18,090 for YZn to —53,430 fov YZr11 and corresponding enthalpies vary from -24,050 to -92,080. The free energies and enthalpies per g atom as a function of composition show a maximum for the YZn2 phase; the 500°C values are -9580 and -13,180, vespectively. 1 HE only information found in the literature on Y-Zn alloys was the observation reported by Carlson, Schmidt. and speddingl that Y-20 wt pct Zn forms a low melting alloy. The alloy was produced by the bomb-reduction of YF3 and ZnF2 with calcium in an investigation of methods for producing yttrium metal. The solubility of yttrium in zinc has been determined by P. F. woerner2 and reported by Chiotti, Woerner, and Parry.3 In the temperature range 495" to 685°C the solubility may be represented by the relation In these equations N represents atom fraction of yttrium and T is the temperature in degrees Kelvin. The purpose of the present investigation was to establish the phase diagram for the Y-Zn system and to determine the standard free energy, enthalpy, and entropy of formation for the compounds formed. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in the preparation of alloys were Bunker Hill slab zinc, 99.99 pct pure, and Ames Laboratory yttrium sponge. Arc-melted yttrium buttons contained the following impurities in parts per million: C-129, N-12, 0-307, Fe-209, Ni-126, Mg-13, Ca < 10, F-105, and Ti < 50. Some of the alloys containing 70 wt pct or more of Zn were prepared from yttrium containing 5000 ppm Ti as a major impurity. Tantalum containers were found to be suitable for all alloys studied and were used throughout the investigation. The pure metals, total weight about 30 g, were sealed in 1 in. diam tantalum crucibles by welding on preformed tantalum covers. A 1/8 in. diam tantalum tube was welded in the base of each crucible for use as a thermocouple well. Welding was done with a heli-arc in a glove box which was initially evacuated and filled with argon. The sealed crucibles were enclosed in stainless steel jackets and heated in an oscillating furnace at temperatures up to 1150°C. Homogeneous liquid alloys were obtained within a half hr at these temperatures except for alloys containing less than 20 pct zinc. The latter alloys were held at 1000º to 1100°C for 2 to 3 days in order to obtain equilibrium. After the initial equilibrations the tantalum crucibles containing the alloys were removed from the steel containers and used directly for differential thermal analyses. Further annealing heat treatments for alloys in which peritectic reactions were involved were carried out in the thermal analyses furnace. After thermal analyses the tantalum crucibles were opened and the alloys sectioned and polished for metallographic examination. In the following discussion alloys referred to as "quenched" were obtained by quenching the sealed stainless steel jacket containing the tantalum crucible and alloy in water. The differential thermal analyses apparatus used was a modified version of the one described in an earlier paper., The graphite crucible was replaced by an inconel crucible, the nickel standard and sampie container were separated by a 1/8 in. MgO plate, no getter was used, and provisions were made to

Jan 1, 1963

By R. W. Parsons

wben a displacement front encounters an isolated permeability heterogeneity, it will be perturbed. The details of this perturbation will depend on the beterogeneity size and shape, the Permeability contrast, and the mobility ratio. This paper deals with the displacement front behavior for one, simple, mathematically tractable model: a circular permeability discontinuity and unit mobility ratio. The progress of an initially planar front is shown for four permeability contrasts: k2/k1 = 0, 5/2, 2, m. The front distortion is more pronounced than streamline and isopotential distortion and it approaches a constant shape downstream from the discontinuity. INTRODUCTION The impact of reservoir heterogeneities on oil displacing processes depends upon the variation of the heterogeneous property (frequency distribution), its disposition (spatial distribution), and the inherent stability of the displacement mechanism.l The interplay of these factors plus the impracticability, if not impossibility, of describing a natural rock system in any detail makes exact displacement front movements difficult to determine. It is useful, however, to be able to qualitatively visualize what heterogeneities will do to a displacement front. In this respect certain simple models that can be treated analytically are of value. The following analysis will show the displacement front behavior for one such model. MODEL DESCRIPTION The flow field is two-dimensional and infinite in extent. The fluid flow is single phase, steady state and unidirectional at x, y = 2 m, or before insertion of the discontinuity. A circular permea- bility discontinuity is placed at the origin. Porosity and thickness are the same within and exterior to the heterogeneity. This is exactly the same model that was used by Greenkorn et al. to check analytically Streamlines as determined by Heie-Shaw flow models and finite difference computer techniques.2 FRONT POSITION CALCULATIONS The results of displacement front calculations are presented in Figs. 1 through 4 for four different permeability contrasts: k2/kl = O, %, 2, m. The times corresponding to the front locations are the Same for the 0 and cases! and for the 1/2 and 2 cases. The determination of front positions at various times is based on known analytical expressions for velocity potentials ().2 and stream functions ().2 These expressions are in terms of the x and y

Jan 1, 1969

By H. J. Ward

RUM Jungle uranium field lies in the subtropical portion of the Northern Territory on the Finniss River, East Branch. It takes its name from a railway siding about 2 ½ miles to the southwest and 52 miles from Darwin. The field can be reached from Darwin by a bituminized road. Monsoonal rains of the wet season, October to April, provide an annual rainfall of about 60 in. Vegetation is of the open forest type with denser tree growth along the watercourses and scattered throughout the area are isolated dense patches of jungle growth which are always found on ironstone cappings overlying limestones. The name, Rum Jungle, is thought to have been derived from this unusual occurrence of jungle growth. The wet season prevents the movement of motor vehicles and personnel. It is not until March, when the grass which ranges up to 15 ft in height is burned and the alluvial flats dry out, that field work can be undertaken.

Jan 12, 1954

By Byron Johnston

IN 1926 I had occasion to make numerous measure-ments with a Pitot tube. The differential gage was mounted in a box, and since the work entailed setting upon girders, staging, and flues of various shapes and slopes, much time was generally expended in getting the box blocked into the level position. This inconvenience was so considerable that I devised the gage stand shown in the accompanying illustration. The gage is bolted to the board seat, the bolt per-mitting unlimited adjustment in the plane of the paper. The seat, carrying the gage, revolves on trunnions, per-mitting unlimited adjustment in a second plane, per-pendicular to the first. Consequently, the stand may be stood up, hung by one corner, leaned against some-thing or simply laid down, and the gage levelled from any position. On uneven surfaces, where the stand naturally rests on only three of its legs, it may be swung in the manner peculiar to the tripod, bringing the center of gravity within the triangle formed by the legs, thereby providing a firm set-up. Rubber stoppers under compression were found to give sufficient friction to hold the seat in the desired position.

Jan 3, 1928

A joint statistical report released by the U.S. Department of Commerce and U.S. Securities and Exchange Commission indicates that business investment in new plants and equipment is expected to total $81.8 billion during 1971. This figure is based on the findings of a survey conducted in late April and May and reflects about a 1 ½ % decrease in investments from the $83.1 billion projected in February. Mining, on the other hand, is still in a bullish mood and is expected to spend $1.99 billion in 1971 compared to $1.89 billion in 1970 and $1.86 billion in 1969. Based on figures quoted above, mining investment in 1971 should show a 5.2% increase over 1970. Carl E. Bagge, president of the National Coal Association, was the dedicatory speaker at the new Milton R. Young Station of the Minnkota Power Cooperative in North Dakota. This new power plant incorporates many innovations which have overcome the problems of using the low-cost lignite abundant in the area. According to Bagge, this development and President Nixon&apos;s recent request for an extra $10 million for coal gasification plants is helping the region lead the way in providing for the power needs of the future. He also maintains that gasification of coal can reconcile coal consumption with the demand for cleaner air, and also assure the nation of adequate pipeline gas.

Jan 1, 1971

By O. G. Bell

Development and exploratory work continued vigorously during 1933 in Southwest Texas and, from a standpoint of new production discovered, the new discoveries probably equal or may even exceed any previous year in the history of this area. While exploratory work has been general over the area much of it has been confined to two localities; namely, northern Duval-southern McMullen counties and Starr County. A persistent effort has been made to open new productive areas in northern Duval County and the adjacent part of McMullen County, occasioned primarily by the fact that the Government Wells group of fields in northern Duval County have been by far the best fields so far developed in this part of the state, and the possibility of being able to find new fields in the same general area under similar geologic conditions. This has resulted in the discovery of three new fields, Northwest Government Wells, Moca and Eagle Hill. In addition encouraging shows have been found in North Kohler, Hoffman, Smith-Hunter and the Ignacio areas with the prospect that continued exploratory work will develop some of these prospects into fields. Wildcatting in Starr County was the continued result of an effort to find a trend of production through the county southwestward from the older Reynosa Escarpment fields in Webb, Jim Hogg and Zapata counties. This same impulse has caused most of the wildcatting in Zapata County. New Fields Cuevitas.—During the early part of the year the Sun Oil Co. began some core-drill work on a block of leases in northern Starr County, then in June drilled a test which found production in the McElroy member of the Jackson at 2200 ft. Drilling in this field has continued but the productive area has not as yet been clearly defined. Seven oil wells and three gas wells have been completed. There is as yet no pipe line outlet for this production, hence no productive history of the wells has been

Jan 1, 1934