Search Documents

By A. B. Kinzel

SINCE the exposition of the behavior of certain iron alloys by Sykes1 involving the existence of an austenite loop and the discovery of such a loop in the chrome iron system by Bain,2 there has been much conjecture both on his part and on the part of metallurgists in general as to the exact shape and location of this loop. In previous work commercial steel has been used and the microscope has been employed to locate the critical points so that the position of the loop has been quite approximate. Numerous attempts have been made to measure the critical points of the carbon-free alloys but all of these for one reason or another have failed. A satisfactory method for studying these phenomena is presented here. MATERIAL The first difficulty in this study was to obtain pure chromium-iron alloys. This has been overcome by melting in a vacuum electrolytic Eton and chromium analyzing 99.84 Cr, Fe and C. A pure magnesite crucible was used and the melt allowed to solidify in the crucible. A typical analysis is chromium, 10.10 per cent., carbon, 0.006 per cent., silicon and manganese nil. To overcome the problem presented by segregation, ingots were made into wire 0.04 in, in diameter. This was accomplished by hand-forging the ingots into rods, using an oxyhydrogen flame for heating, in order to avoid carbon. Subsequently the rods were swaged to wire, the heating being carried out in hydrogen. Thus local segregation was eliminated although differences in analysis between portions 50 ft. apart were noted. An electric-resistance method was first tried to determine the critical points, but due to the physical defects in the wire this failed. Bain had previously shown the presence or absence of critical points in a qualitative way by observing the sag in a catenary. The author has devised the following method which gives an accurate determination of the critical points from expansion-temperature curves of suspended wire, a special telescopic dilatometer being used for the purpose.

Jan 1, 1928

By Gerald V. Jergensen

Does an idea have merit? What does it cost to implement? Can the concept be implemented successfully? The ultimate proof is to try, then see. However, when there are many millions of dollars at stake, blindly building and trying requires considerable courage. Owners and investors in retrospect might choose other less complimentary words. So we might ask, "How might we establish the feasibility of an idea or concept before committing large sums of money to the ultimate test?" From this basic and prudent question, has evolved the engineering concept of the feasibility study. A feasibility study is simply a systematic evaluation of an idea or concept to determine the prospects for success. In a literal sense, a feasibility study considers an idea in terms of its data base, "builds" the idea on paper, "operates" that idea, calculates the cost and benefits, then measures the probable success in terms of some economic, technical or financial standard. Feasibility studies can be quite modest in scope yet provide useful insights as to the viability of an idea. A study might be initiated only to examine the completeness or validity of the metallurgical data base. Another study could be a search for a workable idea or solution to an already-identified possibly troublesome problem. In this latter case, the question, "Will it work?" may be far more important than, "How much will it cost?" Feasibility studies are sometimes global in scope, involving several dozens of specialists and examining an entire "grass roots" mining complex. Other studies may be less ambitious but equally important in examining an expansion proposal or developing new operating techniques. Studies may be commissioned to remove plant bottle-necks, solve maintenance problems and so on. The terms study and feasibility study are used interchangeably in this chapter. They denote a systematic method to examine a proposed concept or idea. DATA BASE Typically, studies are initiated with a minimum amount of specific information and a maximum number of assumptions. As the work proceeds and the data base expands, assumptions are replaced

Jan 1, 1982

By V. E. McKelvey

Some understanding of the United States mineral resource potential is essential for planning and policy making for the future. Reserves of some minerals are essentially lacking and for many others they are sufficient for only short term needs. Estimates of undiscovered resources of many minerals are substantial but are insufficient to support long term requirements, particularly if they continue to increase as they have in the past. Presently, subeconomic resources of some minerals such as aluminum are huge, but their recovery may require increased amounts of energy, which poses problems both as to cost and availability. Beyond these identifiable components of the United States mineral potential, what are the prospects? If they could be identified specifically, of course, they would be included in the above. An unappraised potential of new production and discovery can be expected to exist in known districts, where unproved methods of exploration may yield new discoveries; in new types of ore deposits; in metallogenic provinces as yet unrecognized or poorly explored; in frontier areas and in deeper parts of the crust as yet unexplored; and in presently subeconomic sources that may come within economic reach as the result of technologic advance. Other sources may extend the life of domestic material supplies -- substitution of abundant for scarce materials, recycling and prevention of waste, improved efficiency in recovery and use, and conservation of use.

Jan 1, 1976

By R. T. Mishler

Silver-gold. mine, in northern Mexico, with arrow veins in rhyolite. One fourth area developed has been ore. Deposits average 20 in. wide and 73 oz. silver per ton; diluted in mining to 40 oz. per ton. Developed by drifts and raises at 100-ft. intervals. Samples cut every 5 ft. Ore and waste sampled separately to make combined stoping width 3 or 3 1/2 ft. Ore reserves figured to sloping width; high assays not modified. Tonnage and assay of ore extracted higher than estimates. Ore stoped principally by cut and fill method. Cars from each stope counted and sampled. Cars check tonnage to concen¬trator within 1 per cent.; silver assay 9 per cent. high. Tonnage and assay from scopes corrected to agree with feed to concentrator. Profit or loss for each slope estimated monthly. THE Lucky-Tiger mine is a silver-gold property, situated at El Tigre, in the northeastern part of Sonora, Mexico, at, an elevation of 6000 ft. in the Sierra Madre Mountains. It is 30 miles by wagon road from the Esqueda station on the Nacozari railroad. Since its discovery in 1903, the mine has produced forty million ounces of silver. The ore has averaged 40 oz. silver and 0.25 oz. gold per ton. Copper, lead and zinc have been of minor importance, having averaged 0.4 per cent., 1.1 per cent., and 1.5 per cent., respectively. The richness of the ore,, combined with its occurrence in narrow veins, required the use of the more expensive methods of mining.

Jan 2, 1925

By James F. Kemp

(San Francisco Meeting, September, 1915) THE iron ores of southeastern Cuba present a subject of exceptional geological interest. Their relations to the inclosing rocks are varied and in some cases unusual. The problem of their geological origin is not a simple one and for this reason has occasioned some divergence of views among previous observers. Profiting, however, by. these earlier studies and by more detailed field and laboratory observations as well as by the experience of added years of mining, much more satisfactory descriptions and interpretations can now be prepared. PREVIOUS WORK In 1884, interest in the southeastern coast of Cuba became active among the consumers of iron ore along the Atlantic seaboard of the United States. Active development was undertaken by the Juragua Iron Co., Ltd., a corporation affiliated with the Bethlehem Steel Co., and the Pennsylvania Steel Co. The property of the Juragua company, which is situated about 15 miles east of Santiago, was studied in June and July, 1884, by Dr. James P. Kimball, at the tine Professor of Economic Geology in Lehigh University and one of the best known of American mining geologists. Dr. Kimball published on his return two papers, the first important descriptions which we have of the local geology.1 It is

Jan 9, 1915

By T. S. Lundy, F. R. Winslow

DIFFUSION coefficients of Hf181 in the high-tem-perature bcc phase of reactor-grade hafnium were determined at temperatures of 1795° to 1995°C by standard lathe-sectioning techniques. The temperature dependence of the data may be described by an Arrhenius-type expression for this limited temperature interval. However, hafnium is classed with the "anomalous" bcc metals zirconium, titanium, and y uranium by the low values of Do and Q observed in this study. The hafnium metal was received as 1/2-in.-diameter crystal bar. Analyses by the Analytical Chemistry Division of Oak Ridge National Laboratory showed the major impurity to be zirconium— about 2.1 pct. The total interstitial content was about 225 ppm with 190 ppm of this oxygen. The Hf"' was supplied as HfC12 in HC1 solution by the Isotopes Division of Oak Ridge National Laboratory. The hafnium bar was cut into disk-shaped specimens 3/8 in. long. One of the flat faces of each specimen was metallographically treated and then the isotope was deposited by vacuum evaporation from a tungsten filament. A 3 by 3 in. NaI (Tl) crystal with a single-channel analyzer was used for counting y rays with energies of 0.3 to 0.7 Mev. The as-deposited layers of isotope had counting rates of about 200 counts per sec. Specimens were annealed in argon in a tantalum resistance furnace. Temperatures were measured with a microoptical pyrometer calibrated for the particular furnace sighting conditions. All sectioning was done by standard lathe techniques. Section weights were determined on a semimicrobalance. A density of 12.5 g per cu cm was used in determinations of section thicknesses. Activities associated with the various sections were measured and the penetration data were treated using the computer code by winslow.' In all cases, except for specimens annealed at temperatures below 1795°C, normal Gaussian penetration behavior resulted. At lower temperatures, plots of In A(x) vs x2 were nonlinear [~(x) = relative activity at a distance x from the

Jan 1, 1965

By A. B. Kinzel

SINCE the exposition of the behavior of certain iron alloys by Sykes1 involving the existence of an austenite loop and the discovery of such a loop in the chrome iron system by Bain,2 there has been much conjecture both on his part and on the part of metallurgists in general as to the exact shape and location of this loop. In previous work commercial steel has been used and the microscope has been employed to locate the critical points so that the position of the loop has been quite approximate. Numerous attempts have been made to measure the critical points of the carbon-free alloys but all of these for one reason or another have failed. A satisfactory method for studying these phenomena, is presented here. MATERIAL The first difficulty in this study was to obtain pure chromium-iron alloys. This has been overcome by melting in a vacuum electrolytic iron and chromium analyzing 99.84 Cr, Fe and C. A pure magnesite crucible was used and the melt allowed to solidify in the crucible. A typical analysis is chromium, 10.10 per cent., carbon, 0.006 per cent., silicon and manganese nil. To overcome the problem presented by segregation, ingots were made into wire 0.04 in. in diameter. This was accomplished by hand-forging the ingots into rods, using an oxyhydrogen flame for heating, in order to avoid carbon. Subsequently the rods were swaged too wire, the heating being carried out in hydrogen. Thus local segregation was eliminated although differences in analysis between portions 50 ft. apart were noted. An electric-resistance method was first tried to determine the critical points, but due to the physical defects in the wire this failed. Bain had previously shown the presence or absence of critical points in a qualitative way by observing the sag in a catenary. The author has devised the following method which gives an accurate determination of the critical points from expansion-temperature curves of suspended wire, a special telescopic dilatometer being used for the purpose.

Jan 1, 1928

By W. N. Roberts

Hadfielcl steel has been studied by transmission electron microscopy to determine the microsl.rtic-ture of the cold-worked material, which has been a subject of controversy for many years. The presence of fcc deformation twins in specimens deformed in tension, by hamnzering, and by explosive -shock loading at room temperature lzas been established by electron diffraction. No evidence of a mar tensite was detected in any of the speciwens. Small amounts of E martensite were idenLified in the hamnleved specimens. DESPITE numerous researches on Hadfield steel since its discovery in 1882, there is still disagreement on the nature of transformations in the cold-worked material. Collette el al.,' using X-ray and electron diffraction, have found evidence for stacking faults, E martensite, and a martensite in Hadfield steel deformed in tension at room temperature. Nishiyama and Simizu,' using electron microscopy, have found stacking faults and E martensite in hammered Hadfield steel. White and Honeycombe have concluded from X-ray diffraction that Hadfield steel remains fully austenitic even after severe cold work at -196 Previous work by the author, indicating the presence of a, martensite in deformed Hadfield steel, was in error due to a faulty interpretation of the electron-diffraction patterns. Various workers,5'7 over the years, have speculated on the presence of deformation twins in Hadfield steel, largely from such circumstantial evidence as the persistence of slip bands with repeated polishing and etching, the presence of serrations in the stress-strain curve, and the absence of evidence of a martensite by X-ray measurements. The advent of electron-transmission microscopy and se- lected-area diffraction has made possible the positive identification of fine deformation twinning. PROCEDURE For tensile tests, standard ASTM specimens of 2-in. gage length, ground from 0.12-in. Hadfield steel sheet, were solution-treated at 1050°C for 30 min in a salt bath, to avoid decarburization, and water-quenched. The grain size was about 0.01 sq mm. Chemical analysis of the steel after heat

Jan 1, 1964

By John W. Cabot

THE following series of analyses, which may, be of interest to Bessemer-steel makers, is submitted as a contribution to the much-vexed discussion of manganese in Bessemer steel. They were made by the writer in the spring of 1881, at the works of the Pittsburgh Bessemer Steel Company Limited, during a period of about eight days, part of, which time the rail-steel showed great variation in rolling qualities. During the first part of the time in question, it rolled well; later on it began to roll worse until, finally, it cracked very badly, reaching its worst stage. After this it rapidly improved until it again rolled smoothly. During this .time of transition 'from. good rolling to bad, and back to good again, the course of the manganese was followed' quite closely. It is the striking correspondence between these varying manganese contents and the differences in rolling which is here presented as worthy of notice. The other ordinary elements were determined occasionally, but showed no unusual variation Tim steel, in question, was ordinary rail-steel of about "the following composition : C=.35.P=.08.Mn=.98. Si=.08. S=.05. The samples for manganese determinations were taken at first from an average of two days' work, and later on, when the steel

Jan 1, 1882

By Frederick Forscher

Frederick Forscher (Nuclear Materials and Equipment Gorp.)—It is gratifying to see another series of experimental results that essentially reconfirms our reported observations of "Strain-Induced Hydrogen Embrittlement in Zirconium" (F. Forscher: AIME Trans., 1956, vol. 206, p. 536, noted as Ref. 3 of paper). However, several important considerations may have been overlooked, or—at least—have not been specifically pointed out. It is the purpose of this discussion to present some of these considerations. The statement is made that "the equilibrium concentration of hydrogen in solution at 20°C in zirconium is approximately 10 ppm; i.e., no zirconium hydride precipitates are formed at or below this hydrogen content." This is perhaps the case in the unstressed condition. In the presence of triaxial (plastic) strain however, even as little as 1.4 ppm H2 (Forscher's Figs. 6 and 11) will cause porosity near fracture in 20°C tests. The necked-down region that develops during a tensile test provides the triaxiality necessary for these pores to open. Both Beevers' and Forscher's micrographs show that porosity is concentrated in the necked region. So-called "pure zirconium" containing about 10 ppm H2 also shows pronounced porosity near fracture (Beevers' Fig. 3). Since it is generally agreed that such porosity is

Jan 1, 1965

By John W. Cabot

The following series of analyses, which may, be of interest to Bessemer-steel makers, is submitted as a contribution to the muchvexed discussion of manganese in Bessemer steel. They were made by the writer in the spring of 1881, at the works of the Pittsburgh Bessemer Steel Company Limited, during a' period of about eight days, part of. which time the rail-steel showed great variation in rolling qualities. During the first part of tile time in question, it rolled well; later on it began to roll wome until, finally, it cracked very badly, reaching its worst stage. After this it rapidly improved until it again rolled smoothly. During this time of transition from good rolling to bad, and hack to good again, the course of the manganese was followed quite closely. It is the striking correspondence between these varying manganese contents and the differences in rolling which is here presented as worthy of notice. The other ordinary elements were determined occasionally, but showed no. unusual variation: The steel, in question, was ordinary rail-steel of about the following compusition : C=35. P - .08. Mn - .98. Si = .08. 8 = .06. The samples for manganese determinations were taken at first from an average of two days' work, and later on, when the steel

Jan 1, 1882

By J. G. Eenink, R. A. Cunningham

One phase has been completed of a laboratory invesrigation of formations with relatively high permeability under conditions of overburden, formation and mud coltrmn pressures. The following statements are based on these tests within the limitations described. Drilling rate decreased when mud column pressure was greater than formation pressure. The decrease was primarily due to a layer of cuttings and mud particles held to the hole bottom by the difference in pressure. Much of the force of the bit was wasted in this layer and was unavailable for penetrating virgin formation. Adequate jet velocities helped clean the filter cake and chips away and resulted in increased drilling rate — the higher the jet velocity the faster the drilling rate. Drilling rate increased slightly when formation pres sure was greater than mud column pressure. The i11(reuse resulted from cleaning the hole bottom as formarion fluid flowed into the borehole. Overburden pressure had practically no effect on drilling rate. INTRODUCTION Some formations are difficult to drill in a wellbore hole but are easily drilled under atmospheric conditions in the laboratory. The reasons for this apparent difference in drillability are not fully understood. An increase in formation compressive strength causes a reduction in drilling rate. It has been shown by Griggs1, Handin2 and others3-1 that formation strength increases under conditions of high hydrostatic stress. Based on these results, a decrease in drilling rate would be expected with increased drilling fluid pressure in formations of low permeability having low formation fluid pressure. Such a decrease has been shown by Murray. et a1 and Eckel" This effect holds even when using nitrogcn under high pressure as the drilling fluid (unrc-ported tests from the Hughes laboratory). Poor bottom-hole cleaning may account for decreased drilling rates. Even though it may not be easily explained, evidence of poor cleaning can easily bc seen. One evidence is the increased drilling rate that accompanies decreased balling obtained with addition of oil in some muds used to drill shales.4,7,3 Many variables can affect drilling rates. These may include mud composition and properties, formation properties, bit types and operating conditions, formation fluid, mud column and overburden pressures. These must be studied a few at a time under carefully controlled conditions which simulate actual conditions as closely as possible. The purpose of this work was to investigate effect of overburden, formation and mud column pressures on drilling rates in permeable formations. These tests were suggested by conditions shown in Fig. I. Represented is a borehole drilled into a formation with relatively high permeability. In the vicinity of the hole bottom there exists a mud column pressure, P a formation fluid pressure, P and an overburden pressure, The mud has low water-loss properties and sufficient weight to more than overbalance the formation pressure. Laboratory investigation included a range with formation pressure greater than mud column pressure. NOMENCLATURE Pm mud column pressure = pressure of drilling fluid or mud at hole bottom Pf, formation pressure = pressure of fluid in intersticies of formation

PAST PRESIDENT WILLIS MCGERALD PEIRCE New York City PRESIDENT-ELECT AND TREASURER ANDREW FLETCHER New York City VICE-PRESIDENTS O B J FRASER, New York City J B MORROW,' Pittsburgh, Pa. J L GILLSON, Wilmington, Del L F REINARTZ, Middletown, O PHILIP KRAFT, New York City W THOMAS,' Tucson, Ariz.

Jan 1, 1952

By F. Valton

(Read at the Wilkes-Barre Meeting, May, 1877.) IN the number of the Engineering and Mining Journal for April 7th, 1877, Mr. W. P. Ward, of Cartersville, Georgia, explains in a very interesting manner, the results he obtained in the manufacture of ferromanganese in the blast furnace. These results may be summed tip as follows : Production in the blast furnace of an alloy containing 67.2 per cent. manganese and 3 per cent. of carbon at most, with a utilization of the manganese amounting to 58 per cent. With the exception of the indicated proportion of carbon, which should be almost doubled to express the true state of facts, we would have had no observations to make on Mr. Ward's paper had he taken into account the results obtained in the same line in other centres of production. Before 1870, spiegel with 8 or 10 per cent. manganese only was known among blast-furnace products. In a journey to Sweden, in 1871, I ascertained that the Schysshyttan works manufactured regularly a spiegel with 18 per cent. manganese. Later, at the Vienna Exhibition, in 1873, the Sava and Jauerburg works, in Carniola, presented to the jury a ferromanganese, obtained in the blast fur-

Jan 1, 1878

By M. Cohen, C. Wagner, J. E. Reynolds

If the total volume of a diffusion couple changes during the diffusion, the measurement of distance becomes ambiguous. Use of distance parameters as suggested by Hartley and Crank is discussed. For small concentration differences, the standard form of Fick's second law is retained with conventional length units and the in- terdiffusion coefficient D. It is shown how D can be calculated from experiments involving large concentration differences and analyzed in terms of distance parameters. 'The merits of incremental diffusion couples involving small concentration differences are emphasized. THE conventional form of Fick's second law for one-dimensional diffusion of component B in a binary solution of A and B is where c, is the concentration of component B; x, the distance; t, the time; and D, the interdiffusion coefficient which may depend on ca. Hartley and Crank' have pointed out that Eq. 1 applies only if the total volume of the diffusion couple does not change during the diffusion process; otherwise, the definition of x becomes ambiguous. No change in total volume takes place if the specific volume of the solution is a linear function of the weight fraction Wb, or if the molar volume is a linear function of the mol fraction N. In some alloys, however, these relationships do not hold, and then it is necessary to introduce a modified measure of distance, 4 in order to retain the general form of Eq. 1. The application of Hartley and Crank's suggestions to diffusion in alloys has been discussed by Wagner.' Relation Between Measure of Distance and Units of Concentration The definition of [ depends on the choice of units for the concentration c,, as follows: 1—If the concentration ca is measured as the weight fraction W, (or weight percent), [ = 5, has to be defined so that equal increments of contain equal increments of mass m of the solution, e.g., dm = pSdx = Sdw [2] where p is the local density of the solution, and S is the cross-sectional area in sq cm which is taken to be constant in this problem of one-dimensional diffusion." * da Silva and Mehla have demonstrated the constancy of the cross-sectional area in the usual type of diffusion couple. However, experiments involving diffusion into thin wires4, 5 may exhibit changes in cross-sectional area, and therefore are excluded from the present treatment. Thus and the unit of is gram per sq cm instead of cm. 2—If the concentration c, is the mol fraction N, must be defined so that equal increments of contain equal numbers of mols of solution, e.g., dn= (S/V)dx= Sd [41 where V is the local molar volume of the solution. Thus dt, = dx/V [51 and the unit of is mols per sq cm. 3—If, as may be advisable in the case of interstitial solutions, the concentration C is measured in terms of the molar ratio of components B and A (c,, = Y, = nH/nA, where n and nl are numbers of mols of B and A), = Y has to be defined so that equal increments of contain equal numbers of mols of A, e.g., dnA= (NAS/V)dx = Sdf [6]

Jan 1, 1954

Pursuant to notice duly given in accordance with law and the constitution, a special business meeting of the members of the Institute was held at the office of the Institute on June 27, 1919, at 8.30 P.M., 1573 members were present in person or by proxy. On resolution duly made and seconded, the change of name to American Institute of Mining and Metallurgical Engineers, Incorporated, was authorized and the officers of the corporation were instructed to take the necessary steps to accomplish this result. The votes were 1565 in favor of the resolution and 7 against. It was then moved and seconded that the certificate of incorporation be amended to define the purposes for which the corporation was formed as follows: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in the industries by all lawful means, " etc., etc.-the remainder of the article reading the same. The purpose of this change was to allow the Institute to take any legal means it desires to accomplish the objects mentioned above instead of restricting it within narrow limits. The vote was 1573 in favor of the resolution and none against.

Jan 8, 1919

By MARK H. LAMB

(Canal Zone Meeting, November, 1910.) THE recent growth of a sentiment among cyanide-plant designers against the use of gravity-stamps for the crushing preliminary to cyanidation may be said to date from the almost simultaneous perfection of the ribbed tube-mill liner and of the tall, air-agitation tank. The first step in the resulting change of practice was the universal adoption of the tube-mill for fine-grinding and the use of coarse screening oil the battery. This was the beginning of the surrender of supremacy by the gravity-stamp ; since merely the single fact that it was a more economical machine for crushing fine had retained it in favor as compared with ball-mills, rolls, or steam-stamps. The surrender, however, is not yet complete. It is the universal practice to use rolls where a relatively small tonnage is to be crushed coarse, as, for example, when coarse concentration is included in the plan of treatment. Power, attendance, repairs, and first-cost are smaller for the rolls, under such circumstances, than for stamps; and it is becoming daily more apparent that, with no concentration to provide for, the use of rolls and tube-mills, without the complication of trommels and elevators required by concentration, is rapidly gaining favor in the eyes of the leading designers. The next step was the use of the rapid-running Chilean mill between the gravity-stamps and the tube-mill, which again narrowed the field of operation of the gravity-stamp while radically widening its screen-aperture. Such a combination of stamps and Chilean mill offers advantages when fine concentration is necessary, since the reduction in the Chilean mill call be adjusted easily and governed by varying the screen-mesh. But even concentration is now looked at askance. One of the leaders of this metallurgy has abandoned the separation and

Jul 1, 1910

By B. M. Loring, I. R. Kramer, F. M. Walters

No observations on the mechanical properties of iron-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,1 or whether the lack of ductility observed was due to impurities in the alloys that he studied. EXPERIMENTAL METHODS The alloys were melted in a 100-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb. ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon [ ] was added as ferrosilicon. The alloys forged without difficulty-and were given a 90 percent reduction to 3/4-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for [ ] 24 hr. at 1150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for z hr. at 540°C. (1000°F.) and air-cooled. The tensile specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were V-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1941

By Olin G. Bell

The year 1934 in Southwest Texas was marked by aggressive development and exploratory work and resulted in the finding of five new fields and a new producing horizon in one of the older fields. This activity is the result of a reasonable market outlet for production, on both oil and gas, and the fact that drilling and operating costs are reasonable and that possibilities of finding new productive areas are rather high. A large part of the area is prospective and very little, if any, satisfactory surface geological work can be done. This, together with the possibility of finding new productive areas, stimulates wildcatting throughout the counties under discussion. Development work continued actively in all of the newer fields. Exploratory work was most intense in Duval, McMullen, Starr and Zapata counties. The activity in Duval and McMullen counties was the result of persistent efforts to find new trends of production similar to and perhaps associated with the Government Wells group of fields. The activity in Starr and Zapata counties was stimulated by the discovery of the Sam Fordyce field in Hidalgo County as well as the continued effort to find new productive trends southeastward from some of the older fields in northeastern Zapata County and western Jim Hogg Comity. Statistics on production are shown in Tables 1 and 2. New Fields Lopeno.—The Lopeno gas field in the southwestern part of Zapata County was opened in August, 1934, by R. B. Morrison No. 1 Ramirez. This is an anticlinal structure mapable in Claiborne beds and the producing horizon is the Queen City sand at 2100 ft. in the Upper Mt. Selman. At the close of the year only two gas wells had been completed but drilling operations were in progress on several other wells and a gas line was being laid to the field so that withdrawals from the area will begin early in 1935. Comilas.—The Comitas field was opened by Merle Gunby No. 1 Haynes in a sand at 800 ft. in an area southwest of the Escobas field. The discovery well had an initial production of only about 16 bbl. of oil

Jan 1, 1935

THE SECRETARY The year 1917 has been a notable one in Institute affairs. The usual activities, including meetings, publications, local section interests, library service, and so-forth, have been continued on at least the same scale as previously, and in addition the resources of the Institute have been placed without stint at the service of the Nation, not only for the active prosecution of the military side of the war, but even more especially in the industrial operations which form the very basis of modern warfare. The officers and directors of the Institute have labored both officially and individually, while the Institute as a body, through committees of, prominent members, and through many individual members, has given freely. Finally, Institute funds have been appropriated to an amount exceeding $5000 to accomplish the cooperation with Government bureaus, and provide committee expenses necessary for performing the services that have been given. The President of the Institute had a very large personal share in many of these activities, which will be described in the following pages, as well as in the President's own report. Many of the Institute's members are giving their whole time for. $1 a year, or less, and especial mention should be made of Herbert C. Hoover, Food Administrator, W. L. Honnold, Head of the Commission for Relief in Belgium, Mark L. Requa, Petroleum Administrator, Edgar Rickard and Charles W. Merrill of the Food Administration, S. A. Taylor of the Fuel Administration, W. L. Saunders, B. B. Thayer and Joseph W. Richards who .are giving a. large share of their time to the Naval Consulting Board, W. Y. Westervelt, W.0. Hotchkiss and Harvey S. Mud of the War Minerals Committee, David W. Brunton of the War Committee of Technical Societies, and hundreds of others whose names are mentioned in the Honor Roll of Members. It has also been a notable year in cooperation with sister-societies. The most important event under this head was the accession of the American Society of Civil Engineers into the fraternity of Founder Societies.

Jan 2, 1918