Search Documents

By L. S. Castleman, R. K. Hotzler

We are currently studying the effects on recrys-tallization of impurities diffused into dispersion-hardened alloys. Our interest in this phenomenon was originally aroused by the observation that the recrystallization temperature range of tungsten "doped" with alumina and silica, or with thoria, is lowered drastically if nickel is plated onto the tungsten prior to heat treatment.' In this note, we report a similar effect that sulfur has on the recrystallization behavior of thoriated nickel. The experimental procedure for this exploratory phase of the investigation has consisted simply in heating commercially obtained stress-relieved samples of thoriated nickel for varying temperatures and times in sealed capsules containing air and small quantities of sulfur. The samples contain 2.4 vol pct thoria and initially less than 18 ppm S by weight; they are prepared either from 0.5-in.-ciiam rod stock or from 0.092-in. sheet and are in the "as-received" (stress-relieved) condition prior to exposure. In an atmosphere free of sulfur, such samples do not show evidence of recrystallization after being annealed for 1 hr at a temperature of 2500°F (1372C).2 The photomicrograph in Fig. 1 shows the microstructure of one of our samples annealed for 75 hr at 1000° C (1832°F) in a sulfur-free capsule. The grain structure is hardly evident (if at all) at 465 times magnification. In contrast, the photomicrograph of Fig. 2 shows the recrystallization that has taken place in a sample exposed to sulfur for 5 hr at 1000°C (1832°F). A nickel sulfide phase is visible at the grain boundaries of the light-appearing grains. We have also observed recrystallization to occur in a sample annealed at 600°C (1112°F) for 25 hr. This temperature is below the 637°C (1178°F) eutectic in the Ni-S system. In the latter case, no nickel sulfide phase is evident in the microstructure. Moreover, we have noticed the occur-

Jan 1, 1969

By D. R. Wieland, A. N. Barron, A. R. Hendrickson

A definite relationship has been found between the reactivity of flowing hydrochloric acid and its shear rate in a carbonate fracture. Both flow velocity and fracture width affect the acid reaction rate. Laboratory studies were conducted on acid reactivity at different flow velocities through horizontal-linear fractures, using 15 per cent hydrochloric acid at 80' F and approximately 1,100 psi. Fracture width varied from 0.02 to 0.20 in. These data provide a new basis from which the spending time and penetration of the acid can be estimated. Equations were derived expressing the relationship between injection rate, fracture width, acid concentration, time and fracture height, for linear and radial fracture systems. Because the penetration of the acid before spending is closely related to the extent of productivity increase resulting from an acidizing treatment, these data provide a valuable insight into some of the controlling factors that must be taken into consideration during treatment preplanning. INTRODUCTION Acidizing of carbonate reservoirs to improve production characteristics has been widely practiced since 1932. Originally, it was assumed that the acid uniformly penetrated natural formation pores and flow channels, enlarging them and thereby increasing their flow capacity. Little consideration was given to the reaction rate of the acid, or how far it would penetrate away from the wellbore into the formation, before spending. It has been shown recently' that, unless fractures are present in the rock, very little penetration is attained before spending, and the benefits of the acidizing treatment are largely confined to the immediate vicinity of the well-bore. Therefore, acid treatments may be classified into two categories: (1) matrix acidizing, in which the acid flows through multiple: formation pores; and (2) fracture acidizing, in which the bulk of the acid travels through fractures in the rock, whether natural or induced. When acidizing treatments are conducted at pressures of sufficient magnitude to open and extend such fractures, it is often desirable to inject a propping agent to hold the fracture open after the treating pressure has been released, thus providing a highly conductive flow channel through the rock. In some cases where acid attack produces surface irregularities, the resulting flow passages can be sufficient to provide high conductivity without use of a propping agent. During injection, the acid dissolves the carbonate rock with which it comes in contact until it is spent. Deeper penetration of the spent acid into the formation produces no appreciable benefit (if no propping agent is used) because the unetched fracture faces will rejoin when treating pressures are released and the fracture will "heal", with negligible resultant conductivity. The spending time of the acid thus becomes important in determining how far from the wellbore the improved-conductivity zone extends. The spending time of acid after injection into carbonate rock depends on the rate at which the acid reacts with the rock. This in turn is controlled by a number of factors, as previously reported. 2-4 These include temperature, pressure, acid concentration, rock composition, injection rate and the area-volume relationship between the acid solution volume and the surface area of the formation flow channels through which it penetrates. Thus, in matrix acidizing, where an extremely large area is exposed to the acid, spending is rapid. In contrast, spending time is prolonged in open fractures, where the area-volume ratio is much lower. Thus, greatest penetration of the acid before spending will be achieved in acid-fracturing treatments where fractures are held open by hydraulic pressure. Perkins and Kern5 have presented equations for fracture-width determinations which, for hard formations such as limestone or dolomite, indicate that high injection rates and viscous fluids are required to create wide fractures. Increasing the injection rate will, in itself, produce faster reaction rates. Because this type of reaction can be considered to be first-order diffusion-controlled, '-' the rate of movement of fluid past the rock surface affects the thickness of the diffusion layer, in turn affecting the reaction rate. Staudt, et al,10 report the results of tests in which a rotating marble cylinder was immersed in acid, and the weight loss at different speeds determined. Such test conditions, however, are not truly indicative of the situation in a formation during an acid-fracturing treatment. This paper reports reaction-rate data obtained under

By J. H. Frye, D. L. McElroy, E. E. Stansbury

The rates of growth of pearlite in high-purity Fe-C alloys have been measured as a function of the transformation temperature. These and other data have been correlated in terms of a derived rate equation. Activation energies for the growth were found to be 24,200 cal per mol of austenite for the 0.78 pct C alloy and 27,600 cal per mol for the 0.93 pct C alloy. Theoretical implications are discussed. AN excellent review of the the theoretical and experimental studies on the mechanism and kinetics of the eutectoid reaction has been presented recently by Mehl and Dube.' They have pointed out that these investigations have followed two lines of approach: 1—experimental studies and derivations of expressions for the overall transformation characteristics, and 2—derivation of expressions for the nucleation and growth rates in terms of fundamental processes. Investigations of the latter type have been concerned for the most part with the nature of the growth at the austenite-pearlite interface in plain carbon and alloy eutectoid steels. They discuss two theories of the rate of growth of pearlite from aus-tenite—those of Brandt and of Zener. Both derive rate equations which are based on the assumption that carbon diffusion is the controlling mechanism. Mehl and Dube,' Zener,2 and Brandts. " have attempted to calculate growth rates by use of these equations together with thermodynamic and diffusion data. The results are encouraging, but agreement is not so good as to constitute verification of the theories. Furthermore, it Is not clear how these equations are to be used to study the effect of alloying elements which apparently exert little influence on carbon diffusion, but markedly decrease growth rates. It is not clear whether or not the addition to iron of an alloying element which does not diffuse during transformation can alter the rate of growth of body-centered from face-centered cubic iron. That it can greatly decrease the overall transformation rate has

Jan 1, 1954

By AIME AIME

PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1911.) VICE-PRESIDENTS OF THE COUNCIL. W. C. RALSTON SAN FRANCISCO, CAL. W. L. SAUNDERS NEW YORK, N. Y. H. V. WINCHELL MINNEAPOLIS, MINN. (Term expires February, 1911.) BENJAMIN B. LAWRENCE NEW YORK, N. Y. JOSEPH W. RICHARDS SOUTH BETHLEHEM, PA. ALBERT SAUVEUR CAMBRIDGE, MASS. (Term expires February, 1912.)

Nov 1, 1910

Plans for the Petroleum Division during the ensuing year are in process of development, in contemplation of the usual fall meetings in the Mid-Continent and California areas, as well as the annual meeting to be held in New York in February, 1936. Houston, Texas has been suggested as the place for the Mid-Continent fall meeting, the exact date to be announced shortly. During the past year, the Division's technical programs, as in former years, have emphasized the wide fields of engineering endeavor in the petroleum industry yet remaining for more thorough investigation and discussion. An effort has been made to bring an international interest into the proceedings of the Division by inviting the participation of prominent foreign technologists. This viewpoint should promote a continuation in 1935 of past high standards, afford a more thorough understanding of problems throughout the membership, and maintain the Institute's position among the various technical organizations functioning particularly in the oil-producing and refining areas. In the list of subjects proposed for the fall meetings is the problem of estimating petroleum reserves. Various factors requiring study will include productive sand volume, porosity, average permeability, saturation, and types of recovery. Research papers are proposed dealing with energy consumption per unit of oil recovered, reservoir pressure or energy loss relationship to the usual volumetric method of estimation, and the study of oil and gas segregation within the reservoir. Other subjects tentatively suggested include new casing practice in relationship to wells producing from several productive zones, progress in lifting methods, repressuring, advanced methods in drilling economies, and the economics of conservation. Although the threat of overproduction yet remains, to a lesser degree than during the past few years, intensive activity is now being directed towards the discovery of new petroleum reserves. This situation undoubtedly will influence, in some considerable degree, the channels through which technical activities will be directed. A continuation of the commendable work on production statistics for the various oil-producing states and foreign countries has been effected. The usual papers dealing with the general economics of the industry will be reserved for the annual New York Meeting. The Stabilization Committee maintains its membership of nationwide authorities, and interest is manifest in new developments to meet the changing requirements of the industry.

Jan 1, 1935

By Wilbur E. Sanders

AT some period during the operation of metalliferous and other commercially valuable mineral-deposits in connection with their underground mining, when the developments therein have become so extensive that their description is tedious and confusing, some scheme for naming or numbering the various workings and their parts is necessary for convenience of ; reference.. A simple and symmetrical yet expansive system of classification must be devised, one that is capable of being extended to cover all possible exigencies and conditions of future operations within the property. Such a scheme, properly arranged, greatly simplifies communication between the various departments of the mining business, as, for instance, between the administrative and the operating departments of the concern, and is of the greatest assistance to the officers of the mine in enabling them to locate and describe particular points and parts of workings and specific kinds of work. Again, in the proper segregation and differentiation of mine-accounts, when they are carried out with that detail which will furnish ready information concerning the cost of a particular piece of work, or the various items and totals of expense connected with the, development,, operation and repair of each or all of the mine-workings, some such method of designation becomes a necessity. . Moreover, such a plan is admirably adapted to the needs of the mining engineer, who, in connection with his reports upon mining-properties, is sometimes required, in his descriptions of certain blocks of ore, to locate lists of assays of samples taken from many and various places, and to designate workings and parts of workings that are located in different parts of the mine, sometimes at points wide apart.

May 1, 1906

By W. E. Horst

Flotation feed was hell constant for batch laboratory tests and continuous pilot and commercial plant tests on a spodumene ore to determine the relation.ship between flotation behavior and the size and type of flotation machine. Results. showed that additional retention time would be needed in the plant flotation circuit to duplicate laboratory or pilot plant performance when operating Dariables of the. plant flotation machines remained unchanged. During the past few years of operation at Kings Mountain, N. C., full-scale flotation has generally yielded poorer metallurgical results than those obtained in the laboratory or pilot plant. After 2 min in each size of Denver flotation machine in the spodumene rougher circuit, pilot recovery (41.7 pct) was almost three times that of the plant (13.6 pct) and about twice that of the laboratory (21.0 pct). Pilot and commercial plant data are based on continuous operation, and laboratory results on batch testing of rougher performance. The ore is a pegmatite containing spodumene, feldspar, quartz, mica, and amphibolite. Data were accumulated to evaluate the scale-up relationships between laboratory, pilot plant, and plant flotation cells. Flotation rate constants and dimensional analysis were used to define the relationship existing between flotation behavior and scale of operation. Measuring Flotation Rates: Efficiency of the rougher stage was measured by flotation rate, defined as the recovery that can be attained within a given time." • The problem of measuring flotation rates has been studied by many investigators, whose methods have varied. Published studies an flotation kinetics have been summarized recently by Gaudin.l When comparing flotation rates, it is more satisfactory to compare straight line relationships between recovery and flotation time than exponential curves resulting from plotting cumulative recovery vs cumulative flotation time. To convert the exponential curves into straight line relationships, rate equations were applied similar to those used in chemical kinetics to study the velocity of chemical reactions. Two rate equations have been used in this investigation to measure efficiency of the various cells: 1.5 order Rate Equation dR/dt=k (A-R)1.0 [Eq.1] Second Order Rate Equation dR ---- - K(A - R)2 [Eq. 2] dt Upon integration Eq. 1 becomes 1/(A-R)1/2=k/2 t+1/A1/2 [Eq. 3] and Eq 2 becomes: or fEq. 4] t/R=1/A2K+t/A [Eq. 4] where R = cumulative recovery [percent recovery of total value (spodumene) in flotation feed]. A = initial concentration, pct (100 pct of mineral to be separated). t = flotation time (minutes). k = flotation rate constant for 1.5 order rate equation [units: 1/(percent) 0.5 (min)1. K = flotation rate constant for second order rate equation [units: 1/(percent) (min) 1.

Jan 1, 1959

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

IT is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references 1 to 4. Investigations on the properties at elevated temperatures are few, however,5-7 and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. As is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hardening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During [TABLE I.-Sources of Materials Used in the Testing Program MATERIAL ORIGIN AND TREATMENT 24S-T Alclad.... From Lockheed stock. 24S-RT Alclad... Direct from mill. 24S-T80 Alclad.. 24S-O Alclad from Lockheed stock, solution-heat-treated (925°F., water quench) and aged at 375°F. for t0 t % hour. 24S-T8I Alclad.. 24S-T Alclad from Lockheed stock, plant stretched up t0 I per cent and aged t0 ± % hr. at 375°F. 24S-T86 Alclad.. 24S-RT Alclad from Lockheed stock aged 534 ± 34 hr. at 375°F. 6IS-W (bare).... From Lockheed stock. 6IS-T (bare) 6IS-W (bare) from Lockheed stock aged 8 hr. at 350°F. XB7SS-T Alclad. From Lockheed stock.] the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "overaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: I. The higher the temperature, the more rapidly is the fully aged condition attained.

Jan 1, 1945

By Edward Thomas

THE late George S. Rice was active in the investigation of bumps, particularly in the last ten years of his career as chief mining engineer of the U. S. Bureau of Mines. Since most of his investigation was carried out in Great Britain, continental Europe, and-to a lesser extent-Canada, his thinking on prevention was influenced considerably by the experience of those countries. It is not surprising, therefore, that when he was called upon a few years before his retirement to investigate bumps in the U. S. and suggest ways to prevent them, he turned to longwall mining. A longwall method had been most successful in combating the bump hazard in mining coal under deep cover, especially in Great Britain, but the prevailing method there at the time was advancing longwall mining, which he knew was uneconomical under U. S. mining conditions. For this reason he proposed a modified retreating longwall system that he believed included the best features of the advancing method. As brought out by Rice,1 if the cover is 2000 ft and 50 pct of the coal is extracted, the static load on the remaining pillars will be about 4000 psi, which exceeds the ultimate crushing strength2 in most instances. If the pillar coal is overloaded before a pillar line is established, then the abutment zone preceding a line of extraction is no place to split pillars or extract them by any method other than an open-end system. Rice therefore advocated open-end mining, preferably by longwall, but he was willing to compromise with long-face mining if the longwall method was not acceptable.

Jan 8, 1958

By J. W. Dougherty, J. M. Douglas

THE Hollinger gold mine is in the Porcupine mining division, District of Cochrane, in the northern part of the Province of Ontario. The adjacent town of Timmins, with a population of 25,119, lies 490 miles by railway north of the city of Toronto. GEOLOGY The property is situated on the northwest limb of a major syncline, which pitches northeast at approximately 50°. The principal rocks of the Hollinger area are of pre-Cambrian age and consist of altered, schistose, Keewatin lava flows intruded by stocks of schistose, quartzfeldspar porphyry generally assigned to the Algoman period. The structure of the Keewatin series is extremely complex as a result of close folding and some faulting. The schistosity, trending north 70° east and dipping steeply to the southeast, is most highly developed along a subsidiary anticline in which the major porphyry bodies occur. The ore bodies, which exhibit three principal structures, consist of quartz veins and associated pyritized wall rock. Some lodes are composed of en echelon veins, others exhibit a main quartz body with branching stringers and a third consists of a single definite lead. Gold, in a coarse visible form, may be confined to quartz in some ore bodies but in others it is finely divided and is found not only in quartz but also associated with pyrite in the adjacent wall rock. In many veins the distribution of gold is such that there are several ore sections, separated by areas of low-grade material, in the same vein although its physical appearance remains unchanged. The veins form a very complex pattern in an ore zone which in places attains a length of 6000 ft. and a width of 4000 ft. They are most abundant in the Keewatin lavas in the neighborhood of the porphyry bodies. Few of the veins are persistent for long distances, though some

Jan 1, 1940

By B. Wilshire, W. J. Evans

W. J. Evans and 8. Wilshire SEVERAL recent investigations1-6 have shown that the strain, c, during transient and steady-state creep is well-represented by the expression: € = e0 + et(l - e-mt) + Esl [l] where Eo is the instantaneous strain on loading, ET the total transient strain, C, the steady creep rate! and m a constant relating to the rate of exhaustion of transient creep. However, it has been noted6 that deviations from this equation occur over the first 10 to 15 pct of the transient stage, when the creep rate, (. decreases more rapidly than is predicted by this equation. This rapid decrease has been attributed to a large change in work-hardening coefficient. It 1s widely accepted that steady-state creep results from a balance between the rate of strain hardcning h and the rate of recovery r (=-s(st) as: dE/dt = Es = r/h [2] Comparison of values obtained for h at the end of the initial extension and during steady creep suggests that h increases several fold during the transient stage. which has the effect of reducing the creep rate proportionally.7 To examine the dependence, on r and h, of the deformation behavior during transient and steady-state creep. a series of constant-stress creep tests was carried out at 413°C at 6000 psi using 70-30 a brass. Prelinlinary investigation showed that. with this material. the transient stage constituted a significant portion of the total creep life (-0.4tf. where tf is the time to fracture). The alloy. obtained from Metals Research Limited. was made from high-purity copper, 99.999 pct. and zinc. 99.99 pct. Heat treatment at 675°C for 4 1/2 gave a uniform grain size of 5 mm-1. Details of specimen preparation and creep testing procedures have been given previously.6 Values of h (?s/?E) were determined by measuring the instantaneous strain. ?E. which occurred on increasing the stress during creep by a small amount. ?s. Similarly. v (= -?s/ ?t) was derived from the incubation period. At, after a small decrease in stress.' Several values of v and h were obtained throughout duplicate creep tests. using different stress increments in the range 300 to 800 psi. The accuracy with which Eq. [I] represents the present creep curves was established by determining the best value of the constants Es, Et, m , and 6, using a digital computer program based essentially on the graphical solution for this equation devised by Conway and Mullikan.9 About 40 strain/time readings were taken during transient and steady-state creep. Over most of the creep curve, the average difference between the measured reading and the calculated strain at the appropriate time was less than 0.0001. However.

Jan 1, 1969

By R. D. Vaughn

The limiting cases of non- Newtonian fluids flowing inside a concentric annular duct are developed without using a model of the fluid behavior. The solutions provide limits with which to test the various models of fluid behavior such as the power law and Bingham plastic models. The results of previous theoretical work are discussed in terms of limiting cases. This limiting case study also shows that experimental work on flow of non-Newtonian fluids in annular ducts should be confined to ducts for which the ratio of the radius of the inner wall to that of the outer wall is less than 0.3 and preferably less than 0.2. INTRODUCTION During the last 10 years the problem of laminar flow of non-Newtonian fluids in concentric annuli has received much attention large1y because of its application to the hydrodynamics of the wellbore. Recently solutions utilizing the power law1,2 and Bingham plasticl,3,4 models have been published. In this paper the method of limiting cases, which has been successfully applied to laminar-flow heat transfer516 will be applied to the problem of flow of non-time dependent, non-Newtonian fluids through annuli. This method permits solutions for the limiting cases to be made without using a model of unknown validity. The solutions, therefore, provide limits with which to test the various models which have been or will be proposed. A pertinent conclusion concerning the region of experimental work is also provided. DEVELOPMENT OF LIMITING CASES The limiting cases for the axial flow of fluids in concentric annuli may be defined with reference to Fig. 1. It is possible to define two limiting cases which pertain to the physical dimensions of the annulus. First, the annulus must degenerate to a circular pipe as the radius of the inner wall decreases or, as k = (k R/R) ? 0. Second, the annulus must approach the limit of parallel plates of infinite extent as the spacing between the inner and outer tubes becomes small in comparison with the radius R of the annulus, or as k?1. It is also possible to ascertain three limiting cases which pertain to fluid behavior. With reference to Fig. 2, as a fluid becomes progressively more pseudoplastic, the shear stress-shear rate relationship progressively approaches the indicated horizontal line more closely. At this limit the shear stress becomes independent of the shear rate. At the other extreme of increasingly dilatant behavior, the vertical asymptote is approached. Intermediate between these two limiting cases lies the case of the Newtonian fluid. Fluids which exhibit a yield shear stress also approach the limiting case of "infinite" pseudoplastic behavior. The remainder of the theoretical development is concerned with the description of and the solutions

By R. W. Raymond

(Cleveland Meeting, October, 1912.) UNDER the names of Conservation, Social Justice, the New Nationalism, and Progressive Democracy, many earnest reformers are calling for a new system of Federal government to replace the one which they ascribe to our fathers, and declare to have been outgrown. They are proposing the lease by the United States of certain natural resources on the public domain, for the profit of the U. S. Treasury, instead of the sale of such resources to private citizens or associations of citizens. In the present paper, I shall try to show that this notion is neither new nor good. It is clear that the United States is owner, as well as sovereign, of public lands acquired through conquest or purchase from other nations, as it was owner of the public lands expressly ceded to it by the original thirteen States. Its policy with regard to such lands involves, therefore, two entirely distinct questions: What shall it do as owner ? and, What shall it do as sovereign ? The latter question, it must be confessed, has played but a small part in our history. All the prerogatives of sovereignty which were not explicitly conferred upon the Federal government by the original States were retained by them. The ownership or control of precious or other metals or minerals in the earth, for instance, was thus reserved to the several sovereign States. New York, South Carolina, and other States have passed laws on this subject, without regard to Federal authority. As new States have been successively admitted to the Union, the tacitly accepted theory has been,. that they thereby acquired all the reserved rights of the original States. These newer States largely outnumber the first. thirteen; and it is inconceivable that they would submit to any deprivation of sovereignty based on historical grounds. One of them-Texas-came into the Union by its own voluntary

Oct 1, 1912

By B. J. Steblay

Roof bolts are the primary means of supplemental support in coal mines and are widely used in other mines. Presently, post installation loads are measured infrequently on only about 10% of the bolts by using standard torque wrenches that limit accuracy to about ± 30%. Because mine roof bolts are long, slender, non-uniformly sized, roughly forged, placed in a difficult environment, and subject to severe bending on installation, researchers have been unable to use ultrasonic reflection techniques to measure strain. A complete measurement system has now been assembled by the US Bureau of Mines, Denver Research Center. Obstacles such as bolt preparation, transducer mounting, reliable reflection, and calibration have been dealt with. The seemingly simple concept of measuring the time of flight of an ultrasonic pulse to a reflector is actually complex due to the need to measure to 0.0025 mm (0.0001 in.) accuracy, the sensitivity of velocity to temperature, and stress, and the stability required to make measurements over several years.

Jan 1, 1986

By H. Tanner, T. Heikkinen

In1950 studies concerning mining and milling of the approximately 17 million tons of ore remaining at Outokumpu revealed the surface facilities for economical treatment were inadequate. The two shafts would soon be too far from the mine workings. Moreover, in spite of several extensions, mill capacity was insufficient and recoveries were not satisfactory. Therefore it was decided in 1951 to sink a new shaft and to build a new mill and auxiliary surface buildings around the shaft. The new shaft was sunk near the center of the remaining orebody, about 650 ft from the ore to the footwall side. This location placed the main part of the shaft as well as the crusher rooms and the ore bins around the lower end of the shaft in the firm and strong mica-schist.

Jul 1, 1955

By Geo. W. Bain

PRODUCERS of building stone have had to seek new and attractive uses for their output to supplement the diminished orders for standard products. Lunar is the direct result of the need of new outlets for marble and is. probably the most ingenious and attractive type to reach the market in a quarter of a century. It is a highly translucent stone which retains the same glistening sparkle in transmitted light that marble exhibits by incident rays. This sparkle sets it apart entirely from translucencies made of glass or even onyx, alabaster, and the distinctive exceedingly fine textured calcite marbles produced in Alabama and quarried formerly in northern Vermont and Quebec.

Jan 1, 1936

By P. W. Bridgman

THE thesis of this article is that the age of Newton is now coming to a close, and that recent scientific discoveries have in store an even greater revolution in our entire outlook than the revolution effected by the discovery of universal gravitation by Newton. The revolution that now confronts us, arises from the recent discovery of new facts, the only interpretation of which is that our conviction that nature is understandable and subject to law arose from the narrowness of our horizons, and that if we sufficiently extend our range we shall find that nature is intrinsically and in its elements neither understandable nor subject to law. The new experimental facts are in the realm of quantum phenomena. Comparatively little has been written for popular consumption about this new realm which has opened in the last fifteen years. The man in the street has been much more interested in relativity, which to him has seemed extremely interesting and revolutionary. Occasionally, however, there has filtered down to him the news that nearly all the theoretical physicists are occupied with a new order of phenomena which they find very much more exciting and revolutionary than any in the realm of relativity. For after all is said and done, the practical effects of relativity, measured in ,dollars and' cents or in centimeters and grams, are exceedingly small, and require specially de- signed experiments executed by men of the highest skill to show their existence at all. The phenomena with which quantum theory deals, on the other hand, are of the greatest practical importance and involve the simplest aspects of everyday life. For example, before the advent of the quantum theory no one could explain why a tea kettle of water boiling on the stove should not give out enough light in virtue of its temperature to be visible in the dark; the accepted theories of optics demanded that it should be visible, but every burned child knew that it was not.

Jan 1, 1929

By Max Roesler

Page I. Introduction........................... 78 Location.......................... 78 Scope of Work and Acknowledgments.............. 79 History and Mining...................... 80 I1. Topography and its Interpretation................. 80 III. Petrology............................ 82 Sedimentary Rocks...................... 82 Description....................... 82 Age.......................... 84 Igneous Rocks........................ 85 Diabasic Rocks..................... 86 Dioritic Rocks...................... 87 Granitic Rocks...................... 88 Later Dike Rocks.................... 88 IV. Areal Geology.......................... 88 Rock Types Found in the District............... 88 Distribution of the Various Rock Types............. 89 Surface Distribution................... 89 Vertical Distribution................... 90 Causes of Present Areal and Vertical Distribution of the Various Rock Types..................... 91 Faulting...................... 91 Magmatic Differenti~tion............... 91 Tilting........................ 95 Erosion....................... 96 V. General Description of Ore Deposits................ 96 Nature of Ore ........................ 96 Shap~ and Size of Orebodies.................. 96 Geologic Position....................... 97 Mineralogy......................... 98 Distribution....................... 98 Interpretation...................... 99 Superficial Alteration................... 102 VI. Genesis of the Ore Deposits.................... 104 Previous Theories...................... 104 J. P. Kimball...................... 104

Jan 1, 1917

By L. G. Huntley

Points out differences between the new, more liberal, law passed by the Colombian Congress and the law passed in 1919, gives a few facts about the pipe-line concession granted to a Canadian company, and tells of new drilling developments. PROBABLY the most important development in the Colombian oil situation during the past year was the passage by Congress of a new petroleum law, which went into effect Jan. 31, 1923. The principal points of interest in which this new law changes or improves the previous one are as follows: Law 120 of 1919 provided that one person or corporation could not acquire more than three exploitation zones. of 5000 ha. each, and royalties were based on a sliding scale, to wit: 6 per cent. royalty on lands 400 km., or more, from the ocean; 8 per cent. on lands 200 but not over 400 km. from the ocean, and 10 per cent. royalty on lands located less than 200 km. from the ocean. Rentals were fixed at 10 centavos per hectare for the first year; 20 centavos for the second year; 50 centavos, third year, and $1 (one peso) yearly thereafter. Under this law the term of the lease was fixed at 20 years and, at the discretion of the government, could be extended for 10 years additional. After the expiration of the lease and its corresponding extension, the machinery and other material placed upon the property would vest in the government. A bond of 20,000 pesos was also required of the lessee to guarantee faithful performance of his contract.

Jan 3, 1924

By F. Weston Starratt

The opening of a new large-scale beneficiation plant is always news, but the start-up of Cleveland-Cliffs Iron Co.'s Eagle Mills near Ishpeming in Michigan's Upper Peninsula early in October is of particular interest because of the completely different type of operation being carried on at this plant. The ore boat which left Marquette, Mich. on the 3rd of October bound for the plant of Wisconsin Steel Division of International Harvester, not only carried the first output of this new mill, but also carried the first agglomerate made from the Upper Peninsula's jasper ore, the first commercial output from an updraft traveling-grate furnace, and the first large-scale commercial application of the balling disk, also called the flying saucer, to the agglomeration of an iron flotation concentrate.

Nov 1, 1956