Search Documents

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By A. L. Blomfield

THE Golden Cycle Mining and Reduction Co. operates its custom mill at Colorado Springs on Cripple Creek ores exclusively. These ores are straight sulpho-tellurides, with practically no base metals such as Pb, Cu, Zn, As, or Sb. Upon entering the mill, the ore all passes through the sampler to storage bins, where beds of 5000 tons each are made to insure uniformity in roasting. CLASSIFICATION OF ORES For efficiency, it has been found advisable to separate the ores into two classes according to their line content. Other constituents have their effect, such as alumina and magnesia, but, speaking generally, these are roughly proportional to the line, which, as CaO, is used as the indicator. Class A contains not more than 2 per cent. CaO and comprises about 66 per cent. of the ore treated. Class B contains over 2 per cent. CaO, and comprises 34 per cent. of the ore treated. Typical analyses of both classes are as follows: Class A Class B Insol 56.70 75.90 Al203 2.30 3.40 Fe 3.26 3.48 CaO 1.57 5.12 S 1.79 1.80 Mg0 0.21 1.08 Ignition loss 3.20 6.50 99.03 97.28 The beds of each class of ore are made as large as possible with the available ore as it comes in, to avoid changing from one bed to the other any oftener than necessary. Each roaster will handle 50 percent. more of class A ore than of class B, with practically the same results. This necessitates changing the rate of feed for each new bed and tends toward a poor roast and loss of tonnage at each change.

Jan 8, 1918

By Walter E. Duncan

The ores treated at the concentrating plant of the Mahoning Mining Co. at Rosiclare, III., come largely from the blanket replacement deposits of the northeastern part of Hardin County, Illinois, and consist of complex mixtures of galena, sphalerite and fluorspar in a gangue of quartz, limestone and sandstone. The several minerals are so intimately inter-grown that they are not liberated at the sizes usually treated by gravity concentration in the usual fluorspar plant. For this reason, an all-flotation method of concentration was developed in cooperation with the station of the U. S. Bureau of Mines at Rolla, Mo.1 This flotation separation made possible the commercial production of four concentrates: (I) lead, (2) zinc, (3) acid-grade fluorspar and (4) metallurgical-grade fluorspar.2,3 Although fluorspar had been floated in Canada in 1921 and a plant at Rosiclare had been floating fluorspar since March 1929, fluorspar flotation was given considerable impetus by the Mahoning developments, since some features of the separation were quickly adopted by other fluorspar companies. The Bureau of Mines6 reports that in the 10 years preceding 1938 only 50,552 tons of fluorspar flotation concentrates were produced in the United States. The rise from this almost nominal figure to 153,750 tons (largely acid grade) in one year (1944)6 is indicative of the activity in fluorspar flotation occasioned by the war. The industry thus proved to be in a position to expand and keep up reasonably well with the requirements imposed upon it by such developments as occurred in high octane aviation gasoline alkylation, in the use of Freon as a refrigerant and as carrier in the Aerosol "bug bomb," and in the atomic bomb project as well as in the expansion of other activities requiring hydrofluoric acid; for example, the aluminum industry. Despite the fact that the greater portion of acid-grade fluorspar produced in the last few years went directly into war uses, the future of the acid-grade field still appears bright. As a result of the activity in fluorine chemistry during the war, it seems likely that in the relatively near future almost every phase of human endeavor will find some fluorine compound involved. The other three concentrates produced deserve some attention in these introductory remarks. The lead concentrates first produced contained both zinc and fluorspar but these did not interfere with their marketing. As will be pointed out later, the quality has steadily improved until today it is a relatively high-grade product. Although some zinc smelters accept concentrates containing limited quantities of fluorspar, it is a very objectionable impurity. Since flotation methods fail in the complete removal of the fluorspar, chemical methods were developed for

Jan 1, 1947

By Walter E. Duncan

The ores treated at the concentrating plant of the Mahoning Mining Co. at Rosiclare, III., come largely from the blanket replacement deposits of the northeastern part of Hardin County, Illinois, and consist of complex mixtures of galena, sphalerite and fluorspar in a gangue of quartz, limestone and sandstone. The several minerals are so intimately inter-grown that they are not liberated at the sizes usually treated by gravity concentration in the usual fluorspar plant. For this reason, an all-flotation method of concentration was developed in cooperation with the station of the U. S. Bureau of Mines at Rolla, Mo.1 This flotation separation made possible the commercial production of four concentrates: (I) lead, (2) zinc, (3) acid-grade fluorspar and (4) metallurgical-grade fluorspar.2,3 Although fluorspar had been floated in Canada in 1921 and a plant at Rosiclare had been floating fluorspar since March 1929, fluorspar flotation was given considerable impetus by the Mahoning developments, since some features of the separation were quickly adopted by other fluorspar companies. The Bureau of Mines6 reports that in the 10 years preceding 1938 only 50,552 tons of fluorspar flotation concentrates were produced in the United States. The rise from this almost nominal figure to 153,750 tons (largely acid grade) in one year (1944)6 is indicative of the activity in fluorspar flotation occasioned by the war. The industry thus proved to be in a position to expand and keep up reasonably well with the requirements imposed upon it by such developments as occurred in high octane aviation gasoline alkylation, in the use of Freon as a refrigerant and as carrier in the Aerosol "bug bomb," and in the atomic bomb project as well as in the expansion of other activities requiring hydrofluoric acid; for example, the aluminum industry. Despite the fact that the greater portion of acid-grade fluorspar produced in the last few years went directly into war uses, the future of the acid-grade field still appears bright. As a result of the activity in fluorine chemistry during the war, it seems likely that in the relatively near future almost every phase of human endeavor will find some fluorine compound involved. The other three concentrates produced deserve some attention in these introductory remarks. The lead concentrates first produced contained both zinc and fluorspar but these did not interfere with their marketing. As will be pointed out later, the quality has steadily improved until today it is a relatively high-grade product. Although some zinc smelters accept concentrates containing limited quantities of fluorspar, it is a very objectionable impurity. Since flotation methods fail in the complete removal of the fluorspar, chemical methods were developed for

Jan 1, 1947

By Enrique Touceda

FOR a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At -the outbreak of the war the firm decided to specialize in the manufacture f propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods f manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual -blade mold formed, the pattern is then rotated on the spindle to the position- for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this practice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface f each blade must be chipped too the templet and through this procedure chipped to such accuracy, as will be required for a static balance. Inasmuch as the' work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin f the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days f foundry work and about the same length of, time for the machining. Through the use f the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity, with any particular propeller-wheel design,

Jan 4, 1921

By B. W. Prof. Frazier

I PROPOSE in this paper to treat of the chimney merely as a heat engine, as one of the devices resorted to in practice for the conversion of heat into mechanical work. For the sake of simplicity and clearness in the discussion, let us consider the subject in its simplest form. Conceive a chamber, heated from without, in free communicatioH at one end with the external atmosphere, and at the other end opening into a vertical chimney. Let the. cross-section of the chamber be so great, relatively to that of the chimney, that we can neglect the actual energy of the air passing through the chamber. We will neglect, also, all passive resistances to the passage of the air. We will assume that the cross-section of the chimney is constant, and that the air in passing through it neither gains nor loses heat. The following symbols will be employed in the discussion : Po = the normal pressure of the atmosphere, which, it is assumed, is the pressure existing at the level of the chamber. Po = 10332.96 kilograms per square meter. P2 = the pressure of the external atmosphere at the top of the chimney. To = the, absolute temperature of melting ice by the centigrade scale. This is assumed to be the temperature of the external air at the level of the chamber. To = 273°. T2 =the absolute temperature of the air as it passes from the chamber to the chimney. T3 =the absolute temperature of the air as it issues from the chimney. to, t2, t3 are the temperatures, as recorded on the centigrade ther¬mometer, corresponding to the absolute temperatures To, T2, T3 re-spectively to = 0° C. In general, t = T- 273. Io, I2, I3, represent the intrinsic energy of the air at the temperatures To, T2, T3 respectively.

Jan 1, 1882

By E. L. Affleck, W. G. Stevenson

In both Canada and the United States, a company making a public offering of securities must comply with regulations which have been passed by Federal, State and/or Provincial Legislatures. These regulations usually require the distribution of an acceptable prospectus which provides essential background information about the issuer, the project and the share offering. when the public offering has been accepted, the unlisted company may then seek a listing of its shares for trading on a Stock Exchange. Once listed, the company will be subject to rules of the Stock Exchange. This paper will deal with the specific information required for inclusion into a prospectus being submitted for a resource company and particularly those parts of concern to mining engineers and geologists.

Jan 1, 1985

By Kenneth F. Whinery, John M. Campbell

Basically, the Buckley-Leverett theory involves two systems which are similar in nature but are differentiated by time. These systems may be described by the fractional flow and frontal advance equations which essentially characterize the mechanics of oil movement while being expelled from the reservoir. The fractional flow equation originally developed by Leverettl may be expressed in the more usable form The development of this equation is based on Darcy's law describing fluid flow through porous media and applies to the flow at only one point (it is a point function). For simplification, the fractional flow equation is written in the above form because the capillary forces always increase the fractional flow of the displacing phase regardless of the direction of flow or the displacing phase. If, for simplicity, the effects due to gravity and capillary pressure differences are neglected, the fraction of the displacing fluid, f, at any point in the flowing stream is related to the properties of the system by 1 Thus, it is seen that in the absence of capillary and gravitational effects, fd for a given sand and fluids varies only with saturation and pressure. The magnitude of the viscosity ratio, —a has an effective range (range of about 30) in the system where gas is displacing oil and a much smaller range for water displacing oil. In order to make the fractional flow equation more versatile, it is necessary to connect the fractional flow at a given point and saturation with time. This problem was approached by Buckley and Leverett" who developed the frontal advance equation, Eq. 3 states that the rate of advance of a plane that has a fixed saturation, Sd, is proportional to the change in composition of the flow stream caused by a small change in the saturation of the displacing fluid. It is, essentially, a transformation of a material balance equation representing the net rate of accumulation of the displacing phase within a homogeneous sand block. This accumulation is proportional to the difference between the rate at which the displacing fluid enters the sand and that at which it leaves. Eq. 3 describes the velocity with which a plane of constant displacing phase saturation advances through a porous system. Buckley and Leverett," Babson,' Kern," Welge, and others have adequately discussed the basic mechanism and application of the fractional flow and frontal advance equations. APPLICATIONS OF THE FRONTAL ADVANCE THEORY TO PETROLEUM RECOVERY Two general applications of the Buckley-Leverett frontal advance theory involve the system in which the oil is being displaced by an expanding gas cap overlying the oil zone and that in which the oil is being displaced by water. Displacement by Gas in the Presence of an Immobile Water Saturation A system in which gas is the displacing phase may be thought of as having two forces effecting the displacement process. These forces are the gravitational force and that force exerted by the displacing gas. The gravitational effects control the displacing efficiency of the gas. The gravitational effect will be less at higher rates of flow, thereby reducing the effectiveness of the displacement of the oil by the gas. The more efficient displacements occur at flow rates which are less than the gravity free fall rate. Capillary forces can be neglected without materially changing the magnitude of the gas saturation. The Mile Six pool is used herein to illustrate the calculating procedures in evaluating gas drive-gravity drainage field perfomlance. These calculations represent the determination of the gas-oil contact when the distribution of the hydrocarbon pore volume is considered. Two methods

By J. R. Long, A. H. Roberson, T. R. Graham, R. S. Dean

EXPERIMENTAL work on the properties of high-purity alloys of the copper-manganese-zinc system has necessarily required extensive metallographic work to determine the equilibrium conditions in this system. Previous work on these alloys is fragmentary and, unfortunately, based on alloys made with impure grades of manganese, thus introducing significant amounts of iron, silicon, aluminum and carbon. Since these elements are known to affect equilibrium conditions, it became desirable to re-examine these alloys made from the pure metals. The alpha solid solution field was of particular interest and, therefore, was chosen for the initial work, which was outlined to determine the composition limits of this field. PREVIOUS WORK Heusler1 conducted an extensive survey of the liquid-solid regions of this system and also made an estimate of the solid-phase boundaries at 340°C. The pertinent part of his diagram is given in Fig. I, but it is of limited usefulness, since it applied to a single temperature only and is based on impure alloys under admittedly nonequilibrium conditions. Bauer and Hansen,2 likewise working with impure alloys, have determined the phase boundaries for alphabeta brasses containing small amounts of manganese and indicate an increase in the extent of the alpha field with increasing manganese. This is not in accordance with Heusler or with data obtained on pure alloys.3 They also described a third constituent precipitating in the alpha plus beta field below 350° to 400°C. but did not identify this constituent. Guillet4 and Heike and Ledibur5 have also noted this precipitate Each of these investigators recognized that impurities present in the manganese could and did have an effect on the structure and properties of their alloys. Corson6 in particular pointed out the hardening effects of silicon, aluminum, and carbon in copper-manganese alloys and Heusler reported that his alloys containing more than 25 per cent manganese were extremely brittle. In all probability this brittleness was due to the impurities present. This early work, therefore, should be taken as a general guide for preliminary studies only, and high-purity alloys may be expected to produce different results. The work of the Bureau of Mines laboratories with electrolytic manganese has been briefly summarized by Dean7 but includes only a short section on this system. Later work3 outlined a limited portion of the alpha field in the neighborhood of 65 per cent copper, 10 per cent manganese, and 25 per cent zinc. The present work was under-

Jan 1, 1945

By T. O. Allen, J. H. Atterbury

Laboratory and field tests during the past five years indicated considerable variation in the penetrating power of commercially available gun perforators. Many of the guns which achieved inadequate penetration in these tests have since been improved. However, recent productivity tests indicated the possibility of inadequate penetration or, at least, ineffective penetration in some wells. Laboratory experiments under simulated well conditions have demonstrated considerable plugging of the perforations, apparently as a result of factors associated with the shooting process and/or the drilling mud in the well at the time of perforating. The restrictions to flow per unit of hole depth caused by this plugging appears to be greater for jet perforators than for bullet guns of comparable diameter; however, because of the greater depth of penetration obtained with the jet guns, the total flow rates appear to he approximately equal. Limited testing with an experimental shaped charge suggests that less shot hole restriction and greater flow rates may result from larger-diameter perforations or other factors related to charge design. INTRODUCTION Gun perforating has been accepted for a number of years as a routine well completion method which is often preferred since it permits more selective operation of producing zones. Nevertheless, questions have continued to arise as to the effectiveness of the communication paths established between the productive formation and the interior of the casing. The basis for these questions has generally been failure to obtain anticipated fluid production rates through gun perforated completions in specific wells. These low productivities, together with the frequent recovery of bullets from well bores, were considered strong evidence of inadequate penetration. Laboratory investigations of the penetration performance of many of the bullet guns available as late as 1948 gave support to these indications. Subsequent electrical analog studiesl,2,3 indicated that the depth of penetration required to provide productivities equivalent to open hole was beyond the capacity of most bullet perforators evaluated in the early laboratory penetration tests. These results, together with the advent of the shaped charge in the field of oil well perforating, stimulated the interest of both oil operators and service companies in gun development. Improvements in gun design resulted in jet and bullet guns which appeared to be capable of providing sufficient penetration for most perforating jobs. However, some wells failed to yield satisfactory fluid production even after being perforated with the more powerful guns, again raising the question as to the effectiveness of the perforating operation. This fact, together with preliminary shooting into targets prepared with formation cores, indicated that factors associated with the perforating process and/or the fluids in the well bore at the time of shooting may reduce effective formation penetration and thereby decrease well productivity. These laboratory and field data prompted another phase in the investigation of the effectiveness of gun perforating: a program to determine the extent and seriousness of perforation plugging under simulated well conditions.

Jan 1, 1955

By Arthur L. Walker

DURING my trip around the world last year, covering a total of 45,000 miles, I saw many things of especial interest from an engineering viewpoint. Sailing from New York, I went through the Panama Canal, down along the west coast of South America, then over the Peruvian and Bolivian Uplands; thence to the celebrated copper mines of Chile; across the Andes, to Buenos Aires, then to Rio Janeiro; across the Atlantic to Lisbon, Portugal; through Spain to the Rio Tinto mines; across southern Europe to Italy; thence to Alexandria and Cairo; up the Nile to Assouan, to Palestine through the Suez Canal, Red Sea and across to Bombay; up to the country of the Moghul Emperors; then to Calcutta, from which point I shipped to Singapore, as having crossed the Equator twice, I wished to shake hands with it again; thence to Shanghai and Pekin; up to the Great Wall of China, back to Nanking and up the Yangtse to Hankow; then back and eastward across the Pacific Ocean. The climatic changes were sudden and severe; there was winter where, for me, it should have been summer and vice versa. The weather man was very kind, however, and until I was near the Aleutian Islands there were only three rainy days in a total of 220.

Jan 1, 1924

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC's. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

By Ove Alm

Wet and dry specimens of three rocks of approximately granitic composition were deformed at different experimental conditions. These experiments were carried out in order to study the extent to which water, either added or released from mineral reactions, may affect the mechanical properties and the microstructure of these rocks. The experiments were conducted in a Griggs&apos; hot creep apparatus at temperatures and pressures up to 900ºC and 1000 MPa respectively; and most of them were performed in the constant strain rate mode [(1.10-6 < t < 1 • 10-4 s-1 )]. All three rocks were low porosity rocks, and the wet specimens never contained more than 0.9 wt % of added water. The experimental results are, however, quite unequivocal: They show that wet rocks are weaker than dry ones. A significant difference is even found for rocks tested in uniaxial compression at room temperature. A few experiments carried out on specimens obtained from larger prestressed rock cores indicated that the central parts of these cores were more likely to contain more microcracks than the ends. Optical microscope examinations revealed that extensive microcracking takes place even at the highest temperatures, where other mechanisms such as slip and dislocation creep also become important. Very little partial melting could be observed except for the specimens deformed at 900ºC.

Jan 1, 1982

By L. A. Panek, F. D. Wang, M. C. Sun

A method of stability analysis of underground opening by the limiting equilibrium approach is presented. The Coulomb shear failure criterion is employed to find possible fracture surfaces and to evaluate the shear strengths along them. The normal stresses required for the calculation of shear strength, and the shear stresses for the calculation of total shear force along the fracture surfaces, are obtained by the finite-element method of plane-strain analysis. The factor of safety against Coulomb shear failure is calculated as the ratio of the shear strength to the shear force along a fracture surface, similar to the practice in slope stability analysis. Four shapes of openings are analyzed, with three ratios of horizontal lithostatic stress and four coefficients of internal friction. The critical fracture surfaces found by this method of analysis are consistent with the arching of roofs and slabbing of ribs commonly observed.

Jan 1, 1972

By K. E. Manchester, C. B. Sibley

The feasibility of doping silicon to produce device structres by directly implanting impurity atoms has been demonstrated. Both phosphors and boron ions have been successfully implanted in silicon to produce electrical junctions. Junctions as deep as 1.2 p have been produced by phosphorus ions having energies the order of 80 kev. An electromagnetic separator has been used to controllably produce uniform, large-area implantations for evaluation experimentation. Correlations between junclion depths and ion energies huve been obtained. Orientation effects have been observed and it has been found that the (110) direction is the easy direction for implanting. Monitoring of thermal treatments oj implanted substrates by sheet-resistance measurement indicates a very mild thermal anneal removes most of the damage done during the implantation. These indications are further substantiated by reverse-current measurements of j,inctions Produced by implantation. Electrical characteristics of implanted junctions are compared with those of diffused junctions. We have been interi n the interaction of energetic ions in the III-V groups, in particular boron and phosphorus, with single-crystal silicon to produce type conversion for possible device use. A number of investigators, a few of whom are avies, Kornelson,3 and so forth, have reported on penetration of energetic ions into both amorphous and crystalline solids. While most work has been done with ions of the rare gas and alkali metal groups, some work has been reported by ing, erber,&apos; and others6 in which ions of the 111-V groups have been implanted in single-crystal silicon. A large amount of this work has been done with ion energies in the 100-kev to 1.5-Mev range. An excellent review article has been written by caldin. We have concentrated on ion energies which are in the 10 to 80 kev range, with which over 1500 implanted junctions such as the one shown in Fig. 1 have been produced in silicon substrates with both phosphorus and boron ions. Fig. 1 is a 3-deg angle lap in which the n type area produced by 66 kev P is delineated and the junction is 9500A below the surface. EXPERIMENTAL Implantations reported in this paper were made with the ion source adjusted to produce ion currents in the range of 1 to 2 pa with accelerating voltages varied from 10 to 40 kv. When using doubly charged ions this produced 10 to 80 kev ions. This allowed substrate temperatures to remain below 100°C. Sam- ple movement resulted in beam impingement angle variation of 7 deg from the normal to the substrate surface. Substrate resistivities have been varied through the range of 0.001 to 500 ohm-cm and specimens oriented in three directions, (110), (Ill), and (loo), within 12 deg. RESULTS For the purpose of this paper, discussion of results will be limited to phosphorus implantations with mention of results for boron-implanted silicon. Similar results have been obtained for boron and will be reported at a later date. In Figs. 2, 3, and 4 depth penetration is shown

Jan 1, 1967

By H. E. Biber

DURING the production of tin plate a thin layer of FeSn2, is formed at the interface between the steel sheet and the protective tin coating. Because excessive amounts of this alloy layer are undesirable, the kinetics of its formation is a subject of interest in the tin-plate industry. A recent study of this subject at our laboratory uncovered a relationship which should be of general interest to anyone studying kinetics of reactions in metallic systems. It had been previously concluded that, at any given temperature in the range 175" to 330°C, the Fe-Sn alloy layer would have a parabolic growth rate.1,2 However, our studies showed that this rule apparently holds only when the tin plate is heated very slowly to the "reaction" temperature; when the tin plate is rapidly heated, considerably different growth rates occur. An example of this effect of heating rate on growth behavior is contained in the accompanying results of alloy-layer growth measurements at 240°C in oil baths stirred at 10,500, 1800, and 0 rpm. The heating curves for these three conditions are given in Fig. 1, and the growth data are presented in Fig. 2. With the rapid heating rate, provided by the stirring at 10,500 rpm, the alloy layer had three distinct stages of growth. In the initial stage, which persisted well beyond the time required to heat the tin plate to bath temperature, the alloy layer formed very rapidly. The growth followed a rate law of the form w = ktn where n > 1. This initial stage was followed by a growth-retardation stage of about 50-sec duration in which little additional alloy was formed. In the third stage the growth again followed a rate law of the form w = ktn, but here « =0.3. With the intermediate heating rate provided by stirring at 1800 rpm, the three-stage nature was less pronounced and the slope of the third stage increased (i.e., n > 0.3). With the slow heating rate provided by the unstirred oil bath, the alloy layer grew in two stages. The initial rapid-growth stage persisted only until the specimen was heated to bath temperature, no growth retardation was observed, and the slope of the main portion of the plotted data was greater than in the stirred baths, having a value of almost 0.5. Similar results were obtained for other bath temperatures in the range 200" to 300°C. This effect of heating rate on growth behavior may be due to changes in the rate of nucleation of FeSn, crystallites. The iron and tin are in contact from the onset of heating. Thus the initial formation of FeSn, occurs not at the "reaction" temperature but rather while the tin plate is being heated to that temperature. Because nucleation is in general temperature-dependent, different heating rates could cause different over-all nucleation rates, which in turn could cause different growth behaviors. A more detailed discussion of the growth of Fe-Sn alloy layer and the effect of heating rate will be published shortly.

Jan 1, 1965

By D. N. Dietz

Jan 1, 1969

By G. H. Wigton

THE oxidized ores of the Chief Consolidated Mining Co., in the Tintic mining district, have never yielded to metallurgical treatment by any standard method except smelting. These ores occur in comparatively small, irregular, siliceous replacements in limestone, and carry silver, lead, and gold as the principal valuable metals. But smelting methods. are unsatisfactory, as the lead smelters heavily penalize the large amount of silica in the ore, and the copper smelters do not pay for the lead in the ore; therefore, an alternative treatment method was sought. In 1916, a metallurgical research department was organized under; the direction of the writer. Many standard metallurgical methods were investigated but, on oxidized ore, none yielded extraction great enough to make its use feasible. During some chloridizing-roasting experiments in 1916, made in an assay muffle, the writer noted that large proportions of the silver, lead, and gold were volatilized from certain oxidized ores. The possibility of volatilizing the metals and collecting them in the form of a concentrated fume was then studied. But, as it was shown that satisfactory chloride-volatilization would be limited to a furnace feed with a high fusing temperature of the non-volatilizable constituents, and as the results obtained in a rotary kiln with the admixture of common salt with the ground ore were inferior to muffle tests, further volatilization experiments were discontinued until 1920. During this interval, an experimental sulfidizing and flotation plant was operated. After the cessation of attempts to float the oxidized minerals, chloride-volatilization experiments were resumed. The highly infusible flotation. tailing from the operation of the flotation mill was used for furnace feed. The first tests made on flotation tailing mixed with 10 per cent. common salt showed -nearly complete lead and gold volatilization but considerably less volatilization of silver than in muffle tests. In attempts to increase the silver extraction, the percentage salt in the furnace feed was varied, and it soon became apparent that the use of smaller percentages of salt raised the fusion temperature of the furnace charge and thus,

Jan 8, 1925

By John M. Kelly

New Mexico produced 31,913,816 bbl. of oil in 1942, the lowest annual production since 1936, and dropped one place to rank eighth among oil-producing states. This production decreased 7,838,052 bbl., or 19.71 per cent, from the 1941 figure is the result of transportation difficulties caused by the dislocation of tanker sailings to east coast ports. The average per-well allowable in New Mexico on Jan. I, 1942, was 43 bbl. and at the end of the year was 38 bbl. Allocations as set by the New Mexico Oil Conservation Commission followed the recommendations of the Petroleum Administrator for War. After setting the daily outlet, however, the average daily pipe-line runs were 87,545 bbl.—11.06 per cent short of these allocations. Production for Lea County was 26,812,949 bbl., Eddy County 4,624,578 bbl., northwestern New Mexico 473,609 bbl., Chaves County 2,680 barrels. Drilling activity for New Mexico in 1942 was approximately 84 per cent of that in 1941 with 339 completions. Of these completions 254 were oil wells, II gas wells, and 74 dry holes. Proven fields accounted for 55 of the dry holes and 19 were wildcats. Three new oil fields and one new gas field were discovered as the result of wildcat drilling. Extensions were made to one oil field and one gas field. By the close of the year, the New Mexico Oil Conservation Commission had designated 59 areas as proven for oil and/or gas. Southeastern New Mexico Lea County Monument was again the largest producing field in the state, with 5,729,336 bbl.; Eunice was next, with 5,217,965; Vacuum produced 3,295,624 and Hobbs 2,973,488. The Hobbs field has the largest accumulated production, which at the close of 1942 totaled 100,381,417 bbl. The 100-million-barrel mark for Hobbs focused attention on the fact that this is the first field in the state to attain this figure, and also that, as Hobbs has been under continuous proration since July 1930, or approximately the entire life of the field, this 100-million-barrel recovery was obtained with 86 per cent of the wells in the pool still flowing and having a drop in bottom-hole pressure of only 3.5 Ib. per million barrels recovered. Hobbs stands out as perhaps the best regulated major oil field in the world. Two new oil fields were discovered in Lca County, the most inlportant being the area designated as East Lusk, consisting of the south 4 tiers of Sections in T. 19 S., R. 32 E. The discovery well was drilled in the SW. SW. 1/4 of sec. 21, T. 19 S., R. 32 E., by Culbertson and Irwin, Inc., and others. It was completed at a total depth of 2751 ft. in the Seven Rivers formation of Permian age. The initial potential of the well was 237 bbl. per day on pump. The oil produced has a gravity of 24.10 A.P.I., with sulphur content of 0.9 per cent. This oil has an asphaltic base and because

Jan 1, 1943

By John M. Kelly

New Mexico produced 31,913,816 bbl. of oil in 1942, the lowest annual production since 1936, and dropped one place to rank eighth among oil-producing states. This production decreased 7,838,052 bbl., or 19.71 per cent, from the 1941 figure is the result of transportation difficulties caused by the dislocation of tanker sailings to east coast ports. The average per-well allowable in New Mexico on Jan. I, 1942, was 43 bbl. and at the end of the year was 38 bbl. Allocations as set by the New Mexico Oil Conservation Commission followed the recommendations of the Petroleum Administrator for War. After setting the daily outlet, however, the average daily pipe-line runs were 87,545 bbl.—11.06 per cent short of these allocations. Production for Lea County was 26,812,949 bbl., Eddy County 4,624,578 bbl., northwestern New Mexico 473,609 bbl., Chaves County 2,680 barrels. Drilling activity for New Mexico in 1942 was approximately 84 per cent of that in 1941 with 339 completions. Of these completions 254 were oil wells, II gas wells, and 74 dry holes. Proven fields accounted for 55 of the dry holes and 19 were wildcats. Three new oil fields and one new gas field were discovered as the result of wildcat drilling. Extensions were made to one oil field and one gas field. By the close of the year, the New Mexico Oil Conservation Commission had designated 59 areas as proven for oil and/or gas. Southeastern New Mexico Lea County Monument was again the largest producing field in the state, with 5,729,336 bbl.; Eunice was next, with 5,217,965; Vacuum produced 3,295,624 and Hobbs 2,973,488. The Hobbs field has the largest accumulated production, which at the close of 1942 totaled 100,381,417 bbl. The 100-million-barrel mark for Hobbs focused attention on the fact that this is the first field in the state to attain this figure, and also that, as Hobbs has been under continuous proration since July 1930, or approximately the entire life of the field, this 100-million-barrel recovery was obtained with 86 per cent of the wells in the pool still flowing and having a drop in bottom-hole pressure of only 3.5 Ib. per million barrels recovered. Hobbs stands out as perhaps the best regulated major oil field in the world. Two new oil fields were discovered in Lca County, the most inlportant being the area designated as East Lusk, consisting of the south 4 tiers of Sections in T. 19 S., R. 32 E. The discovery well was drilled in the SW. SW. 1/4 of sec. 21, T. 19 S., R. 32 E., by Culbertson and Irwin, Inc., and others. It was completed at a total depth of 2751 ft. in the Seven Rivers formation of Permian age. The initial potential of the well was 237 bbl. per day on pump. The oil produced has a gravity of 24.10 A.P.I., with sulphur content of 0.9 per cent. This oil has an asphaltic base and because

Jan 1, 1943