Search Documents

By A. Tanaka, K. G. Carroll

The existence of local room-temperature plastic flow in germanium, which has been a subject of controversy for nearly two decades, has recently received renewed attention, albeit no more agreement than hitherto. Phenomenologically one major facet of the problem has been reduced to the question whether or not indentation can be effected in germanium without the introduction of cracks. That plastic flow can be induced at room temperature by fracture appears to have been rather convincingly demonstrated recently by Suzuki and Kamada and by Noble and Henisch.1 The literature contains both direct and incidental references to Vickers and Knoop indentations showing no cracks, within resolution of optical microscopy. Recently, however, following a controversy on the subject,2,3 johnson4 made a study of indentations produced by spherical indenters and concluded that these are accompanied by cracking. This study in-

Jan 1, 1969

By James H. Bechtold

The yield strength of annealed tungsten was found to have a strain rate exponent 12 times as great as that of low carbon steel. The effects of temperature and strain rate could be correlated through the Zener-Hollomon parameter with a heat of activation associated with yielding of 32,000 cal per g-atom. This heat of activation is independent of strain although both the temperature and strain rate dependence of the yield strength vary with strain. MOST metals have mechanical properties that are relatively insensitive to strain rate, especially at temperatures below that at which creep is important. In iron and molybdenum," however, relatively large strain rate effects are observed in the temperature range where the rapid increase in yield strength occurs which leads to the ductile to brittle transition. In this temperature range Zener and Hollomon' have suggested that the effects of strain rate and temperature T on the yield strength could be correlated through a single parameter, P, in the following manner where Q is a heat of activation characteristic of the metal and associated with some unspecified relaxation process. They also observed that if the temperature is restricted to a relatively narrow range— below room temperature for steel—that the logarithm of the yield strength could be expressed as a linear function of the logarithm of P. From this relation the logarithm of stress should be a linear function of the logarithm of the strain rate at constant temperature: where r will be referred to herein as the strain rate exponent. At a constant strain rate the logarithm of stress should be a linear function of l/T, ay(e = C) ~ eT [4] where q = Qr [5] and is referred to herein as the temperature exponent. These equations have been found to relate the effects of temperature and strain rate on the yield strength of molybdenum in the temperature range wherein the ductile to brittle transition occurs, —75° to +150°C.2 Bechtold and Shewmon3 have shown recently that the ductile to brittle transition in annealed tungsten occurs in the temperature range +150° to +350°C. In this temperature range the yield strength in-

Jan 1, 1957

By AIME

D R. GILLSON, who was born in Evanston, Ill., in 1895, is another one of those geologists who received his early inspiration and foundation in his science from that great teacher at Northwestern University, the late Professor U. S. Grant, and then went on to give his time and interest to Institute affairs-like those other Northwestern men, Arthur Blair, Gilbert Cady, Charlie Behre, Evan Just, Ian Campbell, Clayton Ball, and many others. After serving in the Navy in the first World War as, of all things for a geologist, a commissary officer on a transport, he went on to MIT and took his doctor's degree under Waldemar Lindgren in 1923. He even assisted in mineralogy at Harvard and thus had training under another great teacher, Charles Palache. He taught mineralogy and petrography at MIT from 1923 to 1928. After several summers of field work as an assistant in the U. S. Geological Survey, Dr. Gillson joined the staff of the du Pont company.

Jan 1, 1947

By Severn P. Brown

Search for ore continued at a feverish pace-as can be attested to by anyone who has tried to arrange for extensive diamond drilling. The stakes are high, and so is the cost as was indicated by Selco Exploration Ltd. when they announced discovery of base metal sulfides at Uchi Lake in northwestern Ontario. It was apparently their first commercial find after 15 years of exploration at a cost of more than $10 million. For the first time in many, many years the big exploration news has come from east of the Mississippi River. In January, the New Jersey Zinc Co., in an unusually worded press release, stated that they had made a major zinc discovery of 13-50 million tons of ore averaging 5-10% Zn. New Jersey's holdings are said to embrace 500 sq mi. The ore was discovered in eastern Tennessee in the upper part of the Knox dolomite of early Ordovician age. Reportedly the mineralization is at depths of 900 to 2000 ft. Currently about 20 diamond drills are working the area for New Jersey. At least nine other major companies are prospecting the region, which now includes parts of Kentucky. Five hundred thousand acres are said to be under lease. Greatest activity is clustered around Carthage, Tenn. In Missouri, the St. Joseph Lead Co. announced plans to develop a new mine in the Brushy Creek area of the "New Lead Belt." copper and zinc concentrates will be by-products.

Jan 1, 1970

WHERE "MINING AND METALLURGY" OR THE TRANSACTIONS MAY BE CONSULTED For the convenience of members Who may be traveling from place to place, the Secretary has compiled a list of libraries or other places in the United States ant foreign countries where MINING AND METALLURGY or the Transactions may be con suited , This list will be sent to members if they so request

Jan 1, 1923

By F. M. Lyon, F. J. Chernosky

Research efforts have not developed techniques for the complete desulfurization of coal that is needed to reduce air pollution caused by burning coal and to reduce the sulfur in metallurgical coke. Sulfur in coal occurs in three forms and of these, the pyritic sulfur occurs as discrete mineral particles and, at least theoretically, should be subject to physical rejection. Pyrite occurring in hard rock mining is concentrated by froth flotation; therefore, the possibility of removal of pyrite from coal by flotation does exist. With this possibility in mind, the flotation and adsorption characteristics of ore and coal-pyrite were compared while using potassium ethyl xanthate as the collector.

Jan 1, 1973

By David B. Reger

The year 1935 was mostly quiet in West Virginia, and devoted to routine drilling in old pools and extensions. A notable exception to this general rule, however, was the further development and proving of a field of gas discovered in 1930 in the deep Oriskany sand (L. Dev.) in Kanawha County, as later discussed. No new pools of oil were found and little or no attempt was made to search for them. No new pools of gas were recorded but various extensions of old pools were made. There were no new pipe line extensions of consequence, either for oil or gas. Operating technology was much the same as in recent years, there having been some further advances in repressuring oil wells and in the use of acid for treating small wells in calcareous formations, and some change in the technique of shooting gas wells. Financially, there has been a full market for all crude oil produced and a fair market for gas. There have been occasional transfers of producing oil or gas properties, mainly between established companies. Most of the attempts made to finance mergers and new developments have failed largely because of difficulties encountered under the Federal securities act. This situation has prevented the normal turnover of properties by small operators who frequently desire to sell partly developed interests and then step out into new ventures. New Development In 1935 the State issued 569 permits for drilling and records the same number of completions. One trade journal records 533 completions and another 483. A running record kept by the writer accounts for 713 completions, with 156 oil wells, 417 gas wells and 140 dry holes (Table 3). Some of these completions may be old wells drilled to deeper sands. Some, apparently, have been drilled without legal permit. Extensions of Producing Areas Ritchie County has again led all others in new drilling, with 137 completions as compared to 74 in Calhoun and 61 in Cabell. This Ritchie County drilling was done mainly to extend or further develop old pools

Jan 1, 1936

By David B. Reger

The year 1935 was mostly quiet in West Virginia, and devoted to routine drilling in old pools and extensions. A notable exception to this general rule, however, was the further development and proving of a field of gas discovered in 1930 in the deep Oriskany sand (L. Dev.) in Kanawha County, as later discussed. No new pools of oil were found and little or no attempt was made to search for them. No new pools of gas were recorded but various extensions of old pools were made. There were no new pipe line extensions of consequence, either for oil or gas. Operating technology was much the same as in recent years, there having been some further advances in repressuring oil wells and in the use of acid for treating small wells in calcareous formations, and some change in the technique of shooting gas wells. Financially, there has been a full market for all crude oil produced and a fair market for gas. There have been occasional transfers of producing oil or gas properties, mainly between established companies. Most of the attempts made to finance mergers and new developments have failed largely because of difficulties encountered under the Federal securities act. This situation has prevented the normal turnover of properties by small operators who frequently desire to sell partly developed interests and then step out into new ventures. New Development In 1935 the State issued 569 permits for drilling and records the same number of completions. One trade journal records 533 completions and another 483. A running record kept by the writer accounts for 713 completions, with 156 oil wells, 417 gas wells and 140 dry holes (Table 3). Some of these completions may be old wells drilled to deeper sands. Some, apparently, have been drilled without legal permit. Extensions of Producing Areas Ritchie County has again led all others in new drilling, with 137 completions as compared to 74 in Calhoun and 61 in Cabell. This Ritchie County drilling was done mainly to extend or further develop old pools

Jan 1, 1936

By Charles Barron McIntosh

BECAUSE of the well known relationship between a low atmospheric pressure and increased amounts of methane in coal mines, attempts have been made to find associations between low pressures and coal mine explosions. An early study by F. Able disclaimed this relationship. He found that half the explosions took place during a rising barometer when methane content in a ventilated mine would be decreasing. A more recent study by C. L. Hosler revealed a close relationship between anthracite mine explosions and low atmospheric pressure. Bituminous coal mine explosions, where coal dust as well as methane can be exploded, were found to be more closely associated with a rising pressure following a low barometer than with the falling or low pressure period. Emphasis on rising pressure periods led the present writer to investigate the effect of the post-frontal or post-cyclonic weather on coal dust. Dust samples of uniform mesh were exposed in an Illinois mine. Analyses of the dust taken before and after the passage of cold fronts and their accompanying low pressure troughs indicated an increase in coal dust moisture prior to a frontal passage and loss of moisture from coal dust following the time of lowest pressure. Thus the warm, moist air (Tropical Maritime)found over the mine during the falling pressure period was cooled in the mine and moisture added to the dust. Cold, dry air (Polar Continental) accompanies' the rising barometer following a frontal passage and the air, being heated in the mine, subtracted moisture from the coal dust. A similar but seasonal phenomenon occurs from summer to winter, the dry dust period in winter being recognized as the more dangerous period. The question arose as to how the short period or daily changes in moisture content of coal dust compared with the seasonal changes. Temperature and humidity statistics were obtained from the surface and mine entry for the months of July andJanuary. The gain and Ioss of mdisture. to the hine were calculated for these two morths as were the gain and loss associated with mT (Tropical Maritime) and cP (Polar Continental),air masses as observed in the investigatiynsl. Temperature and humidity statistics tigatiynsl.taken from [the two air masses represent atimp span of only 34 hr. The redultant changes as presented in the accompanying table verify the supposition that short period changes in coal mine moisture may attain the magnitude of recognized dangerous seasonal changes. Statistics for the mT air and the July air have been placed next each other and those for cP and January air together for easier comparison of the two warm and two cold air units. The last column readily reveals that there is little difference in the amount of moisture being deposited in the mine from the mT air and the July average air. A similar conclusion is reached regarding the loss of moisture from the mine when it is affected by the cP air mass or the average January air. This comparison would be particularly true from late fall through early spring when strongly contrasting air mass changes are a common occurrence. The invasion of cold, dry air following a cold front thus produces a drying period that could well receive more attention as a danger period for coal dust explosions. This drying period would compare with Able's explosion period during a rising barometer. The drying period is also perltinent in Hosler's findings, where it was noted that the average explosion day (for bituminous coal mines) followed the day of lowest atmospheric pressure. Moreover, the author's investigation of some 365 coal mine explosions also indicates that this post-frontal period should receive special attention in connection with mine safety measures. Two comparatively recent major explosions in Illinois (Centralia and West Frapkfort) occurred after the mines had been under the influence of cold-dry air for 25 to 30 hr-following a deep low pressure passage. Dust was the important explosive element in both these explosions.

Jan 1, 1958

By C. A. Stetefeldt

Metallurgical processes cannot be conducted successfully With out the aid of analytical chemistry. The great perfection of Iead smelting in the West, for instance, has only been accomplished by the analysis of ores, fluxes, slags and all products of the furnace. Ores are mixed and fluxed to obtain a slag of desired composition. Account is even taken of the composition of the ashes obtained from the coke. The " muscular " smelter has left the field forever! This state of affairs has been induced by sharp competition, i.e., by a com plete separation of the industries of mining and reducing ores, not by the liberality and wisdom of directors and stockholders to pro vide laboratories and engage chemists, or by their love for scientific investigation. It would be considered absurd, at present, to run a lead-smelter, a blast-furnace for pig-iron, or a Bessemer plant without the assist ance of a well-equipped laboratory and a chemist; but it is con sidered quite sufficient to provide amalgamation- or lixiviation works merely with a crude assay-office, and an assayer who is paid less than a laborer in the mill. In my opinion, this will change in the near future. By the ex clusion of Mexican lead-ores, and their growiring scarcity in the West, smelters have been forced to raise their charges on so-called dry silver-ores, and cannot handle the latter now in such unlimited quantities as formerly. The inevitable result must be that the sur plus of these dry silver-ores, especially those of low grade, will be reduced by processes cheaper than smelbing; and here the introduc tion of lixiviation has an excellent field, provided the muscular lixiviator has an able chemist for an assistant. It is to be regretted that so little analytical work has been done in lixiviation. We know almost nothing of the composition of roasted ores before and after lixiviation; of the constitution of the first wash water and of lixiviation-solutions after prolonged use; of the chemistry of sodium and calcium sulphides; of the col-hposition

Jan 1, 1892

By T. H. Dunn, P. L. Menaul

This paper discusses the results of an investigation made to develop a method of combatting corrosion of subsurface oil-well equipment caused by brines containing hydrogen sulphide. Carbon monoxide, aldehydes, and certain cyanide compounds were found by laboratory tests to effectively inhibit corrosion of steel by sulphide brines. Experiments were made for one year in eight wells in West Texas fields using formaldehyde as an inhibitor. It was found that the inhibitor treatment successfully prevented the severe corrosion previously experienced in these wells, and effected important net savings in operating costs. Introduction Corrosion of oil-field equipment has long been a problem in areas producing sour crudes. These areas include the major fields of Arkansas, Western Kansas, West Texas and New Mexico. Corrosion in these fields is caused primarily by the chemical action of hydrogen sulphide in the presence of water and by electric currents entering the wells through flow lines. Hydrogen sulphide is noncorrosive to iron or steel in the absence of water but under the usual conditions prevailing in oil wells where more or less water is present, hydrogen sulphide is very corrosive. This type of corrosion occurs over the pH range below 9, which includes all natural oil-field brines. If air is present in addition to hydrogen sulphide and water, corrosion proceeds at an extremely rapid rate. It was reported several years ago that a string of oil-well tubing was literally dissolved within 50 days where an air lift was used on a well producing considerable water and hydrogen sulphide. Air is generally absent in wells producing sour crude. After hydrogen sulphide corrosion starts, it proceeds with increasing severity and its correction becomes progressively more difficult. This characteristic of sulphide corrosion has been attributed to the formation of galvanic couples between the iron and steel equipment on one hand and the products of corrosion on the other.' Severe corrosion of subsurface oil-well equipment leads to a multitude of troubles. In addition to destruction of costly equipment, producing sands often are damaged by flooding with water leaking through corroded casing; bad mechanical conditions may develop in a well due to obstructions caused by corroded equipment lost in the hole, or partly collapsed casing; pumping operations are interfered with, and severe emulsification problems may result from the homogenizing action of corroded balls and seats.% A typical case of severe corrosion caused by hydrogen sulphide was reported in Howard County, Texas, where it was necessary to pull tubing once a week to repair leaks after the tubing had been in use for only one year. On one well in this area a string of tubing was pulled 11 times in 8 months; 11 joints of tubing being replaced because of leaks. In Ector

Jan 1, 1946

By T. H. Dunn, P. L. Menaul

This paper discusses the results of an investigation made to develop a method of combatting corrosion of subsurface oil-well equipment caused by brines containing hydrogen sulphide. Carbon monoxide, aldehydes, and certain cyanide compounds were found by laboratory tests to effectively inhibit corrosion of steel by sulphide brines. Experiments were made for one year in eight wells in West Texas fields using formaldehyde as an inhibitor. It was found that the inhibitor treatment successfully prevented the severe corrosion previously experienced in these wells, and effected important net savings in operating costs. Introduction Corrosion of oil-field equipment has long been a problem in areas producing sour crudes. These areas include the major fields of Arkansas, Western Kansas, West Texas and New Mexico. Corrosion in these fields is caused primarily by the chemical action of hydrogen sulphide in the presence of water and by electric currents entering the wells through flow lines. Hydrogen sulphide is noncorrosive to iron or steel in the absence of water but under the usual conditions prevailing in oil wells where more or less water is present, hydrogen sulphide is very corrosive. This type of corrosion occurs over the pH range below 9, which includes all natural oil-field brines. If air is present in addition to hydrogen sulphide and water, corrosion proceeds at an extremely rapid rate. It was reported several years ago that a string of oil-well tubing was literally dissolved within 50 days where an air lift was used on a well producing considerable water and hydrogen sulphide. Air is generally absent in wells producing sour crude. After hydrogen sulphide corrosion starts, it proceeds with increasing severity and its correction becomes progressively more difficult. This characteristic of sulphide corrosion has been attributed to the formation of galvanic couples between the iron and steel equipment on one hand and the products of corrosion on the other.' Severe corrosion of subsurface oil-well equipment leads to a multitude of troubles. In addition to destruction of costly equipment, producing sands often are damaged by flooding with water leaking through corroded casing; bad mechanical conditions may develop in a well due to obstructions caused by corroded equipment lost in the hole, or partly collapsed casing; pumping operations are interfered with, and severe emulsification problems may result from the homogenizing action of corroded balls and seats.% A typical case of severe corrosion caused by hydrogen sulphide was reported in Howard County, Texas, where it was necessary to pull tubing once a week to repair leaks after the tubing had been in use for only one year. On one well in this area a string of tubing was pulled 11 times in 8 months; 11 joints of tubing being replaced because of leaks. In Ector

Jan 1, 1946

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Opening for man as head of laboratory of large brass manufacturing plant in Ohio; must also be competent to manage foundry making brass castings, following practice of malleable iron castings and insulating materials. Good opportunity for right man. No. 36. Professorship in Mining at a Western university; requires man competent to give instruction in ore dressing, in metal and coal mining, and in zinc smelting, and capable of gaining confidence of mining interests. Salary $2,200 to $3,000. No. 37. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of - the Institute by members or other persons introduced by members.) Member, graduate engineer, aged 44, with over 20 years' experience in connection with large coal and coke operations in different parts of the country, desires position as general superintendent of large coal company, or will take an interest with the management in a smaller company. No. 206.

Jan 6, 1915

By G. A. Merkt

THE Isley furnace control, here presented as a novelty in furnace construction, is, in principle, one of the oldest methods of maintaining furnace heat for industrial purposes. Records unearthed in Egyptian tombs and the primitive methods of melting metal practiced by African tribes today indicate that fanning the fire and forcing the furnace by bellows have been an effective means of regulating heat for man's work during thousands of years. Even today, these cruder forms of mechanical draft production are still nn use within the borders of this most highly developed industrial land. Stacks, as we know them, are of com- paratively recent historical age but their attractive simplicity and seeming effectiveness have made them exceedingly popular. And so we find one of the most important types of furnace the world has even known, the open-hearth furnace, duly and more or less properly equipped with a chimney. The regenerative, or reversing, type of furnace, how-ever, required another mechanism between its hearth and the stack to provide a means for alternately con-necting one side and the other of its system of regen-erative chambers and flues to the stack and to a source of fuel and air supply respectively. Various types of reversing valves were developed, some of which are re-markably well designed for maximum efficiency and ease of installation as well as operation. However, this combination has a number of inherent faults which are so difficult to correct as to make efforts in the direction of improving over-all efficiency almost futile. These inherent difficulties are as follows: (1) The necessarily high temperature at which the gases must be delivered to the stack in order to make it operative. (2) The great temperature difference incidental to the reversal of flue gas and air and consequently the large variation in preheated air and fuel delivered to the furnace dur-ing the cycle. (3) The leakages and resistances created by the reversing apparatus and the complicated flues necessary. (4) The inadequate range of control af-forded by the natural draft system, especially under adverse atmospheric conditions.

Jan 12, 1927

By C. H. Li, J. A. Sarteli, W. Bonfield

The stress to cause a permanent micros train of 2 x 10-6 in. per in. (defined as the microscopic yield stress) in beryllium is found to be very sensitive to surface condition. The initiation of plastic flow in as-machined specimens, which contain a high density of twins and large residual compressive stresses to a depth of about 0.010 in. from the surface, occurs by the nucleation of slip from high stress fields around twin tips in the surface layers. Removal of the damaged surface layers by chemical polishing results in an appreciable increase in the microscopic yield stress, which is attributed to the remoual of stress raising twins rather than to the release of residual stresses. IT is well known that the macroscopic mechanical properties of beryllium are very sensitive to the nature of its surface finish. Matthews and coworkers1 have shown that the tensile strength of rolled beryllium sheet can be considerably enhanced by chemical polishing, presumably due to the removal of the high concentration of notches, twins, and large residual compressive stresses normally found in the surface layers of ground specimens. There was no similar effect of surface condition on the macroscopic yield stress (the stress to produce 0.2 pct strain), a point to which we shall return. To date there have been no extensive studies on the effect of surface condition on the microstrain region of beryllium. Recent measurements2 of the stress to cause a permanent microstrain of the order of 10-6 in. per in. on machined hot pressed QMV beryllium, gave values ranging from about 600 to 3500 psi. Reasons for the considerable scatter in the results were not discussed. In this paper, we wish to show that the microstrain region of polycrystalline beryllium is, in fact, very sensitive to surface condition. The stress to cause a permanent strain of 2 x 10-6 in. per in. which for convenience we will refer to as the microscopic yield stress, can be increased by almost a factor of 2 by minimizing the amount of surface damage. The variation of microscopic yield stress is attributed to the presence of twins in the surface layers, rather than to residual compressive stresses. EXPERIMENTAL PROCEDURE The starting material for this investigation was commercial purity hot pressed QMV beryllium, with an average grain size of about 20 . The effects of surface treatment were assessed by comparing the microstructure with residual stress measurements and microstrain properties. Specimens were prepared for metallographic examination by wet grinding with 240, 400, and 600 papers, followed by polishing with a suspension of fine alumina in warm 20 pct oxalic acid. After this treatment, the surface could be examined, either in the unetched condition with polarized light, or after etching in 2 pct hydrofluoric or boiling 20 pct oxalic acid with normal light. Thin films of beryllium suitable for electron transmission study were prepared from bulk specimens by chemical polishing with hydrofluoric and phosphoric acids, and were examined in an RCA-EMU-3 electron microscope. Residual stress measurements were made by a procedure similar to that of Treuting and Read.3 Specimens 4.0 in. by 0.625 in. by 0.080 in. were prepared by three different machining procedures, namely: turning, grinding, and sawing, in order to introduce different levels of residual stresses. An electrical resistance strain gage was attached to one side of the specimen, and that surface was then protected by an acid-resistant enamel, while the opposite surface was removed by etching approximately one thousandth of an inch at a time. The change in specimen curvature in the longitudinal direction was noted and the residual stress was calculated by the following formula:

Jan 1, 1963

By Leroy U. Gardner

EVERY reader of this paper is well aware of the fact that the prolonged inhalation of large amounts of free silica dust results in fibrosis of the lungs, and that other inorganic dusts, except those of asbestos and the mineral poisons, are thought to be relatively harmless. But probably few have had opportunity to visualize the effects of silica, asbestos and other minerals upon living tissues. The ideal demonstration would be based upon sections of lungs from human beings that had inhaled com- parable concentrations of different dusts for a unit period of time. Such material is generally difficult to obtain and in some instances is of questionable value because the subject has been exposed to more than one kind of dust. A demonstration could be prepared from the lungs of animals. However, so many months or even years are required to complete the exposure to each kind of dust that enough material has not been accumulated. For a general survey of the action of different types of dust, I am therefore compelled to use the tissues of animals that have been injected with suspensions of dust particles. The injection method offers certain advantages. The quantity, the particle size and the state of dispersion can be controlled with sufficient accuracy so that the tissue responses to different minerals can be accurately compared. The method insures contact between the tissues and the mineral particles; protective mechanisms, which may prevent the inhalation of certain types of foreign body, never come into play. If the pathway of injection be one that minimizes nonspecific injury, the tissue responses may simulate those produced by inhalation but they develop somewhat more rapidly. It should always be remembered that injection methods merely demonstrate the capacity of various kinds of minerals to provoke reaction in the tissues; whether the same substances are inhaled from atmospheric suspension and accumulate in the lungs in dangerous quantities can be demonstrated only by inhalation. The reactions that I shall discuss first took place not in the lungs but in the liver. For the purpose in hand this is quite immaterial for we are merely seeking to discover whether these minerals are capable of produc-

Jan 1, 1938

By Ernest J. Stocking

ENGINEERS are the key men in our war program today. Upon the technical knowledge and skill of the engineer and upon his administrative and executive abilities rests the entire success for the production of vital materials of the war. Naturally the work load of the engineering examining unit of the U. S. Civil Service Commission has increased greatly since our active participation in the war. At present, over 550 separate requests for certification of eligibles are received by the engineering unit per week. These represent more than a fourth of the total requests received for personnel by the Commission's central office at Washington and represent a recruitment work load of three to four times that carried by the whole Commission previous to January 1940. These requests represent a minimum of a thousand vacancies to be filled each week, while an average week will produce, at present, approximately 1400 vacancies and a weekly maximum may approach well over 2000 vacancies.

Jan 1, 1942

By W. R. Crane

While professiorlally engaged in the oil- and gas-fields of Kansas, in measuring the pressure and flow of gas-wells, and studying the phenomena attendant upon the production of both oil and gas, I noticed in the flow of gas a peculiar and interesting feature. That there are actual lines of flow in liquids (non-compressible fluids) discharged through an orifice, or a short section of pipe, is shown by the external shape of the discharge—the vena contracts. Such lines of flow are not observable in the discharge of gas from an orifice. It can hardly be questioned that they exist. That they are not apparent is probably due to the very small weight of the gaseous particles, which climinishes the momentum of their movement in a given direction, acquired before they issue from the orifice, and also to the expansion of the gases, which would exert a powerful influence in overcoming any such tendency in their flow. Gas flowing from an orifice, supplied by a large reservoir or blowing-engine, exhibits almost the reverse of what is noticed with liquids. Namely, the gas assumes the form of an inverted truncated cone, of large angle: with its apex-end at the orifice. (See BB, Fig. 1.) This external ahape assunled by the flow of gas shows, however, marked differences under varying conditions of volume and pressure. For instance, a large volume of gas under high pressure, flowing through a 2- or 3-in. pipe, as in the case of a natural gas-well, assumes a more definite conical form, the angle of which increases as the pressure falls. Moreover, outside of the well-defined inverted cone is a thin conical heath or zone of gas, A A, the angle of which is considerably greater than that of the main cone, and increases with +1UNIVERSITY OF KANSAS, LAWRENCE, KANSAS.

Jan 1, 1905

The Joint Economic Committee's subcommittee on international payments and exchange has recommended that, following international monetary reforms, the law which prohibits private possession of gold by American citizens be repealed. The subcommittee recommendation called for reforms to enhance the role of special drawing rights in international monetary affairs and downgrade the role of gold. Special drawing rights, also known as "paper gold", are on artificial reserve with the International Monetary Fund (IMF) which distributes them to member nations in proportion to their economic importance in the world economy. The special drawing rights are then used to settle debts between nations in the same manner as gold or currency. The subcommittee said that under the reforms now being discussed special drawing rights would be acceptable in lieu of gold among the member countries of the IMF.

Jan 1, 1973

By George Stern

The purpose of this investigation has been to study one method for making ordinary carbon steel by the powder metallurgy technique. This method con- sists of pressing and subsequently sintering an intimate mixture of iron powder and gaphite in a suitable atmosphere to Produce a steel. Two types of iron Powder have been studied, electrolytic and reduced. The sinkring of mixtures of loose Car-bonyf iron and carbon black for several hours at I000 to 1100 C. (1830' to 2010°F.), followed by forging of the resultant ingots to bars, has been studied by Offermann.' TrailZ has reported on the properties of hydrogen-reduced and electrolytic iron powders, both containing 0.5 per cent carbon. Methods for making steel bodies by powder metallurgy have also been sug- gested by Goetzel13 who recommends the addition of steel powder of well-defined carbon content to pure iron powder, and Volterra,~ who suggests compaction and subsequent sintering of a mixture of steel powder, iron oxide and iron powder. Additional methods for making steel bodies by powder metallurgy have been reported in the literature by Kohering Allen,6 Balke,7 Wulff,8 Boegehold,9 and others.,0,11,12 It is felt that the method of pressing iron powder and graphite, as described herein, lends itself best to production be-Cause of the lubricating action of the

Jan 1, 1946