Search Documents

By M. E. Fine

IN the apparatus for measuring internal friction shown in fig. 1, a modification of that described by Kê,1,2 the parasitic energy loss or background is equivalent to a Q-1 of approximately 4x10-5. This low value of background was obtained by using a jeweler's collet of appropriate size for the upper support, eliminating lateral motion without immersing the bob in oil, and designing the bob to reduce air resistance. The pendulum is supported on the frame through a snug fitting, sliding rotary joint (fig. I-B). A slight twist of the top imparts essentially pure torsional motion to the pendulum. No evidence of energy loss in the sliding joint has been observed. In the bob (E) steel balls are used in the torsion arm, and the bottom is filled with lead giving a total weight of 94 g. A lighter bob may be used for small diameter specimens. Another bob was a solid disc with provision for adding discs to change the frequency. The oscillating image of the filament is recorded on a revolving drum camera (fig. 1-3) driven by a synchronous motor. This allows use of frequencies higher than can be measured visually on a glass scale. Samples varying in diameter from 0.020 to 0.075 in. have been measured, the frequencies have ranged from 1 to 12 cps, and the maximum strain varied from 0.5 to 10x10-5. With appropriate modification the sample may be placed in a thermostat. The apparatus may also be used to measure the shear modulus. In the examples of measurement given in table I the internal friction of Permendur and the 46.8 Ni-Fe alloy are due, for the most part, to magneto-mechanical hysteresis8 (elastic hysteresis accompanying stress-induced magnetostriction) which depends on strain amplitude and increases with annealing. The internal friction of most materials decreases with annealing. References IT. S. K6: Physics Review (1947) 71, 533. 2 T. S. Kê: Transactions AIME (1948) 176, 448; Metals Technology (June 1948) TP 23703. 3 R. Becker and W. Döring: Ferromagnetismus. 365 (1939). J. Springer.

Jan 1, 1951

By Leonard Greenburg

The American literature in the field of dust sampling and analysis has been growing rapidly since 1915. Studies made since that time clearly indicate that there are three fundamental factors that determine the production of lung pathology due to dust inhalation. These are the duration of exposure, the chemical and mineralogic nature of the dust and the concentration of the potentially harmful dust. In the estimation of the amount of the potentially hazardous dust there are essentially three problems involved: (I) a determination of the size of the hazardous dust; (2) determination of the most satisfactory apparatus and technique of sampling, and (3) the most satisfactory method of analysis. A complete study of the literature shows that industrial dust varies ill size from ultramicroscopic particles to those larger than lop in diameter and that relatively few particles are found over 5u in diameter. Approximately 10 to 25 per cent are less than 0.811 in diameter and the median size as a rule is found to lie between 1.25 and 1.75 microns. From the point of view of lung pathology the particle sizes of most importance lie between 0.5 and 5u. Of all the instruments for sampling dust the Impinger apparatus is the only one that will sample a larger body of air satisfactorily with small control errors and high efficiency in both low and high concentrations of dust. The Owens apparatus has the advantage of being more portable and somewhat easier to use but it does riot permit of the sampling of large volumes of air. It has a low efficiency in high concentrations of dust and does not permit dust weights to be obtained. From the point of dust-counting technique the author points out that in 1922 considerable experimentation with dark field and oblique illumination resulted in the conclusion that such methods were not readily duplicated from day to day and therefore yielded somewhat erratic results. Changes in the amount of illumination produced variations of several hundred per cent in dust counts obtained with dark ground

Jan 1, 1934

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Dick Whittington, W. R. Taylor

GENERAL In mid-1974, a representative of ARCO Petroleum Company walked into our Austin offices and asked for a permit for ARCO's first Clay West Mine site. This was the first in situ uranium mining permit issued in the United States. That initial permit, issued in January 1975, was for three acres. The four years since have been characterized by growth and change. Today there are 16 permits approved for approximately 1,540 production acres issued to five companies at eight sites in four counties. There are approximately seven additional permit applications being processed or on the verge of being submitted for an estimated 2,000 additional acres of production. As a rough gauge of the financial scope of this activity, at the typical 40 production wells per acre and an estimated $2,000/well, operators hale installed or committed $122 million for production wells. This does not account for the exploration and development wells installed to delineate the ore or the cost of processing facilities for extracting the uranium. HISTORY OF URANIUM MINING IN TEXAS Information I have concerning early in situ uranium mining activities is "sketchy" but the apparent first on-site test of in situ uranium mining was conducted between 1967 and 1971 at the Dueterstat site, north of Yorktown in Gonzales County, by City Service. Others ran tests at the Bruni site in Webb County and the Burns and Clay West sites in Live Oak County in the mid-70's. During this period, Texas Water Quality Board personnel in the central and district offices maintained a general surveillance of these various test activities. Regulation of in situ uranium mining was formalized with the issuance of a permit in January 1975 with the advent of ARCO's initial production scale (3 acre) effort in the Clay West area at the Moser mine site. Since 1975, the accelerating rate of mining and exploration activity is noticeable. There were 16 exploratory rigs operating early in 1977. This year, the rig count is averaging 46--a 287% increase. HISTORY OF LEGISLATION Paralleling this mining activity was state and federal legislation which subjected in situ mining to environmental regulation. The following is a brief chronology of the legislation that is directly or indirectly related to uranium mining. As most of you know, disposal wells are an integral part of most in situ uranium mines operating in Texas. They are used both during production and during aquifer restoration following production. The wells are regulated by the Texas Injection Well Act, enacted in 1961 by the Texas Legislature. In 1967, the Water Quality Act established the Texas Water Quality Board, and provided for the regulation of water quality by the so-called permit system. In 1969, the Solid Waste Act was enacted by the Texas Legislature. The legislation provides for control of wastes from manufacturing, mining, and agriculture. This Act regulated uranium surface mining activities until 1975 when the Texas Surface and Mining Reclamation Act placed responsibility with the Railroad Commission for uranium open-pit mining and surface mining of coal and lignite. In 1972, the Federal Water Pollution Control Act (Public Law 92-500) was passed. This legislation forms the legal base for the NPDES (National Pollutant Discharge Elimination System) and the subsequent point source effluent guidelines and standards. The November 6, 1975 issue of the Federal Register published interim final rules for Best Practical Treatment levels for effluent discharges from ore mining and dressing operations. Litigation was immediately initiated by eleven companies against these proposed rules, and they are currently being reconsidered for reissuance in 1979. In 1974, the Federal Safe Drinking Water Act (Public Law 93-523) was enacted. A part of this legislation is the Underground Injection Congrol Program. The regulations implementing this program have undergone various public hearings and it is expected that they will be published in the Federal Register before the end of 1978. In 1975, the Texas Surface Mining and Reclamation Act (Senate Bill 55), providing for the Railroad Commission's authority to require reclamation of surface mines, was passed. In 1977, an amendment to Senate Bill 55 was introduced that proposed to place regulation of in situ mining of coal, lignite, and

Jan 1, 1979

By J. R. Thompson

It is common practice, and certainly good business as all of us know, to take care of plant operating equipment. Machinery of any type requires periodic inspection and planned maintenance. With this thought in mind a plant operator should at the end of every shutdown period make regular belt inspections and plan for later appropriate care and maintenance. The points mentioned below are understood well by all of us but are sometimes forgotten because belt conveyors are comparatively easy to operate. Maintenance of any conveyor belt is dependent upon the fundamental characteristics of the two component parts-cover and carcass.

Jan 6, 1950

By J. H. Brophy, A. L. Prill, H. W. Hayden

An error lzas been found in the conventional way of determining the time exponent of linear shrinkage for the solution-precipitation stage of liquid-phase sintering. Large amounts of shrinkage due to initial rearrangenzent result in erroneously low exponents and tni si dentification of the rate-controlling process. Two alternative, mathematically correct, methods of calculation are applied to existing data on Fe-Cu, WC-Co, and Tic-Ni-Mo. This results in reidentifi-cation of the rate-controlling process and somewhat better agreement with related data. In each case the solution-precipitation process is solution-controlled and not diffusion-controlled. THE liquid-phase sintering process has been the object of a considerable amount of research for many years. Linear shrinkage vs time data at various sintering temperatures have been used recently in an attempt to identify the prevailing mass-transport processes in a number of metallic and nonmetallic systems. There is an analytical error inherent in the methods previously used for handling data during the "solution-precipitation" stage of shrinkage which must be recognized before the correct rate-controlling processes can be determined. It is the purpose of this paper to show how the error has affected previous conclusions and to suggest corrections. A number of mechanisms have been proposed to explain experimental observations during sintering in the presence of a liquid phase. The earliest of these is due to Price, Smithells, and williamsl who attributed the observed growth of the solid phase to the simultaneous solution of smaller particles and growth of larger particles. From the work of Lenel et al.2,3 and Gurland and Norton4 has come the suggestion that the liquid-phase sintering process may be divided for analysis into three steps: 1) rearrangement upon formation of the liquid phase; 2) solution and reprecipitation of the solid phase in the liquid; and 3) "coalescence" or a final stage of sintering, characteristically slower than the solution-precipitation process. The sequence of steps is shown schematically in Fig. 1. Kingery5 presented a thermodynamic and kinetic analysis of the first two "stages" of the liquid-phase sintering process in which the functional dependence of lineal shrink- age on time at temperature was used to identify the rate-controlling mass-transport process. Table I summarizes the time dependences and processes considered by Kingery.5 This method of data presentation has been employed by Kingery and coworkers for Fe-CU,6 WC-Co, and a number of nonmetallic systems," and bv Whalen and Humenik for Tic-Ni-Mo and Fe-cu.8 In each of these studies, the rate-controlling step during the "solution-precipitation" stage was identified from the slope of the curve in that stage on a logarithmic plot such as Fig. 1. However, in all of the previous studies, at a certain composition, relatively large amounts of shrinkage due to rearrangement preceded the solution-precipitation stage. Under these conditions, the larger the amount of rearrangement shrinkage the

Jan 1, 1965

By W. R. Ingalls

THE bases of the work by the committee whereof I am chairman were (1) the abolition of extra-lateral rights and (2) the preservation of the maximum of the existing laws. The matter of extra-lateral rights had been under prolonged discussion among mining men and up to the time when our com-mittee began its work (in 1917) the expression of opinion in every way whereby it could be made known -and those ways were extensive-was only a little short of being unanimous that extralateral rights ought to be abolished. I have not observed important evidence indicating a change of opinion on the subject since 1917. ABOLITION OF DISCOVERY LOGICAL Now, when it be decided that extralateral rights ought to be abolished, there can not be merely a simple change to that effect, but it is found that consequential changes are necessary all the way through the existing laws. Abolition of extralateral rights implies abolition of discovery as a prerequisite to location, for otherwise there would be no legal means for locating claims on the dip of a vein. Quite apart from this consideration, abolition of discovery as a prerequisite to location is supported by other good reasons. Among these are the occurrence of orebodies with no exposure on the surface and which often are hidden at great depth. A prospector who has reason to suspect the occurrence of such an orebody must have legal means for the location of a claim within which to explore, and obviously he may. not be able to make any discovery on the surface sufficient to locate and hold legally such a claim under the terms of the law as it stands at present. As a matter of fact, discovery as a prerequisite to location was abolished by common consent many years ago, not only for the reasons that I have given here-inbefore but also for others. It is highly desirable to revise the mining law in this respect, so that it will conform to the conditions of practice and not require people to perjure themselves in making locations, even if it be for praiseworthy purposes.

Jan 6, 1922

By Glenn C. Waterman

THE diamond drill is a very important tool in exploration and development testing and its use is increasing. In almost all cases results of diamond drilling are analyzed on the basis of grade and tons. A proper evaluation of core and sludge assays is important if drilling results are to be acceptable as a basis for geologic and engineering appraisal. The relatively wide variation in assay averages as calculated by various well-known combining methods indicates that the engineering choice of a method may affect the outcome of the drilling in terms of ore and waste. The problem of combining assay results from core and sludge samples has been discussed many times in conference and in the literature.'" Most writers agree that the field of disagreement in methods is large and that the engineer on the job must consider features unique to his drilling, pick one of several combining methods, and depart from the rules when abnormal results come in. All the discussion to date can be summed up by the admission that as yet there is no fairly simple, generally acceptable combining method that is practicable over a wide range of drilling conditions, ground conditions, and ore occurrence.

Jan 1, 1955

By R. G. Wheeler, J. W. Goffard

The Larson-Miller parameter was used to correlate time, temperature, and indentation creep of magnesium, aluminum, and some of their alloys. In the temperature range 300" to 450°C, the short-time Meyer hardness of pure magnesium was less than that of the magnesium alloys tested, but for long times the pure magnesium has greater indentation creep resistance. Aluminum (1100 alloy) had 1.5 to 2.5 times more indentation creep resistance than magnesium at 300" and 450oC, respectively. Hardening of aluminum with a dispersion of Al2O3 was effective in the time and temperature ranges studied. New technologies have required the development of new materials and the utilization of the more familiar materials for new and unusual applications. The use of magnesium and aluminum and some of their alloys, because of their desirable nuclear characteristics, light weight, low cost, and ready availability, has been extended to the 300" to 450°C temperature range. In this temperature range the basic consideration of these materials must be their rate of plastic flow rather than offset yield strengths. The indentation testing reported here arose from a need for design data for the load-holding ability of supports made of these materials. Test Procedure—Hardness indents were made with a 0.275-in.-diam quartz indentor and a 10.65-lb load. The indentor was made by fire-polishing a spherical surface on the end of a fused quartz rod. The samples were held at temperature in a graphite crucible controlled to ±2°C. A thermocouple was attached to the sample and test temperatures were recorded. The diameter of the spherical indentation was measured at the end of a test period and the compression stress (Meyer Hardness) was determined by: H___________load__________ m = projected area of indent Samples were 1 in. in diam and at least 1/4 in. thick. It was observed that at the higher temperatures and longer times, the quartz indentor would stick to the magnesium sample. The quartz indentor was, therefore, frequently inspected and fire-polishing repeated when necessary. The area of sticking was always a small fraction of the area of indent and was therefore considered to have an insignificant effect on results. Correlation of Hot-Indentation Test Data with Time-Temperature Parameter—Sherby and Dorn' have correlated creep or tensile data of a' solid solutions of aluminum with a temperature and strain-rate parameter suggested by Zener and Holloman. underwood2 used this parameter to correlate creep properties of some steels with hot hardness, and upon the basis of this correlation a means of obtaining creep properties from short-time (and inexpensive) hot hardness tests has been demonstrated. Since the validity of the correlation of creep properties with a time-temperature parameter and the correlation of creep properties with hot hardness have been shown, it follows that hot hardness may correlate with the time-temperature parameter. The hot-indentation data obtained was expressed as Meyer hardness, and was shown to be time and temperature dependent. Correlation of Meyer hardness, time, and temperature with the parameter was made using the relationship: Hm = Meyer hardness t = time, hours T = absolute temperature, OK K = constant A value for the constant K was calculated by equating In l/t + K/T at different temperatures and times but at the same hardness. The correlation was tested by plotting Hm vs the parameter, In 1/t +K/T. Since materials are being sought which have high hardness at low indentation creep, i.e., a high Meyer hardness for long time at high temperatures, low values of the parameter are ofthe most interest. TEST RESULTS Magnesium—Pure magnesium (99.98 pct) cut from extruded rod was indentation tested perpendicular to the rod axis at temperatures of 300°, 350°, 400°, and 450°C for times ranging from 6 sec to 112 hr. Fig. 1 shows the time dependency of Meyer hardness at the four constant temperatures. Fig. 2 shows the correlation of the Meyer hardness of pure magnesium with the time-temperature parameter using a K of 22,720 in Eq. [I]. At the bottom of Fig. 2, the effect of doubling the time of indentation t2 = 2(t1), on the abscissa for any time is shown graphically. This effect is of constant magnitude. Also shown graphically are the magnitudes of the effects on the

Jan 1, 1960

By R. A. Pallanch

SODIUM sulfite as a zinc retarding agent in the selective flotation of complex lead-zinc sulfide ores was discovered by the writer in the summer of 1919 in the testing laboratory of the U. S. Smelting, Refining & Mining Co.'s gravity concentrator at Midvale, Utah. It proved to be the first reagent to give consistently good results in the laboratory on the company's Bingham ore. In December, 1919, C. A. Lemke, concentrator superintendent, recommended that a flotation unit be added to the existing gravity mill to handle the mill slimes, using sodium sulfite as the zinc depressant. Owing to the poor lead and zinc markets and the unfavorable royalty schedules offered by the Minerals Separation Co., the project fell through at this time. In 1921, a number of laboratory tests were made at Midvale on other ores, among them ore from the Sunnyside mine at Eureka, Colo. Both sodium and calcium sulfites were used with success on this ore. Early in 1923, further tests were made at Eureka, shortly after the Sunnyside company had resumed operations after a two-year shutdown. As a consequence sodium sulfite was given a trial in the mill. The results showed sufficient improvement over previous work as to warrant continuous use of this reagent in the lead circuit. Except for a week or so in 1926 and for several weeks in April, 1927, when sodium cyanide and zinc sulfate were given trial runs in this mill, sodium sulfite has been used ever since. Sodium sulfite was chosen rather than the calcium sulfite because of its greater solubility, making it possible to introduce the reagent as a solution. This solution is introduced into the Marcy ball mills along with the original feed of ore. The consumption of sodium sulfite in the Sunnyside mill varies from ¼ to ½ lb. per ton of ore, the smaller amount probably being nearer the average. In February, 1924, laboratory work at Midvale demonstrated conclusively that good results could be obtained on the company's Bingham ore and on most of the custom ores tested by using sodium sulfite as the zinc depressant, xanthate as the lead enhancer in the lead circuit, followed by copper sulfate and additional xanthate to float the zinc. Sodium sulfide was used to float the iron pyrite after the lead and

Jan 1, 1928

By H. E. Rorschach

Activity in Oklahoma fields declined in 1938 from the banner year of 1937. During the year, 1768 wells were completed as compared to 2632 completed during the year 1937. The following tabulation sets out details regarding the wells completed during the year: These computations do not take into account the wells drilled for repres-sure and salt-water disposal, and other nonexploratory wells. Purchasers' reports filed with the Corporation Commission of the State of Oklahoma show a total of 168,789,229 bbl. of oil purchased from Oklahoma leases in 1938, or a daily average of 462,436, a decrease of about 25 per cent from the year 1937. The outstanding operation of the year was the further development of the Ramsey pool, in western Payne County, the producing horizon being classified as the Wilcox. This pool was discovered on the last day in the year 1937, by the Mid-Continent Petroleum Corporation drilling on a unitized block in see. 18, T. 18 N., R. 2 E. The map in Fig. 1 shows the development at the end of the year 1938. An important discovery of the year was the Champlin Refining Company's No. 1 Boehm, in Garfield County, sec. 4-24N-8W., the producing horizon being the second Wilcox found at a depth of approximately 6700 ft. This pool was assigned the name of Hillsdale. Some of the offsets to this discovery well had not come up to expectations at the end of the year, but the discovery seems to be important as indicating that the Wilcox sand is productive in the Anadarko Basin area, providing that the right structural conditions are present.

Jan 1, 1939

By H. E. Rorschach

Activity in Oklahoma fields declined in 1938 from the banner year of 1937. During the year, 1768 wells were completed as compared to 2632 completed during the year 1937. The following tabulation sets out details regarding the wells completed during the year: These computations do not take into account the wells drilled for repres-sure and salt-water disposal, and other nonexploratory wells. Purchasers' reports filed with the Corporation Commission of the State of Oklahoma show a total of 168,789,229 bbl. of oil purchased from Oklahoma leases in 1938, or a daily average of 462,436, a decrease of about 25 per cent from the year 1937. The outstanding operation of the year was the further development of the Ramsey pool, in western Payne County, the producing horizon being classified as the Wilcox. This pool was discovered on the last day in the year 1937, by the Mid-Continent Petroleum Corporation drilling on a unitized block in see. 18, T. 18 N., R. 2 E. The map in Fig. 1 shows the development at the end of the year 1938. An important discovery of the year was the Champlin Refining Company's No. 1 Boehm, in Garfield County, sec. 4-24N-8W., the producing horizon being the second Wilcox found at a depth of approximately 6700 ft. This pool was assigned the name of Hillsdale. Some of the offsets to this discovery well had not come up to expectations at the end of the year, but the discovery seems to be important as indicating that the Wilcox sand is productive in the Anadarko Basin area, providing that the right structural conditions are present.

Jan 1, 1939

AT THE beginning of December, the Lausanne Con-ference was in session. The representatives of the United States declared the American position. The representatives of Russia were received and were heard. The Turks appeared at this conference in the attitude of victors, dictating terms. The British refused to surrender Mosul, and December thus ended with this question unsettled. Early in the month the premiers of the principal powers met in London for the discussion of the German reparations question, the temporary agreement expiring on. Jan. 15, 1923. On Dec. 11 the Conference adjourned without getting anywhere, and at the end of December prospects looked more hopeless than ever. The premiers are to meet again on Jan. 2, 1923. The interruption of the London conference was followed by the intimation of early participation of the United States in European affairs in the practical way of a large loan to Germany. These intimations, ema-nating from Washington, appear to have been in the nature of trial balloons. They showed that the wind was unfavorable, the bankers not considering conditions suitable for the flotation of such a loan. British statisticians are puzzled by the fact that the trade returns of Great Britain show a greater turnover in the volume of goods during the first 11 months of 1922 than in 1920, although the rate of labor employ-ment in 1920 was nearly 100 per cent. and in 1922 only about 86 per cent., with an economic situation admit-tedly so bad as to be alarming. The British Parliament was convened under the premiership of Bonar Law. One of its first acts was confirmation of the constitution of the Irish Free State. Civil war in Ireland continued. Poland, like most of the other countries of Europe, is torn between socialism and conservatism, with the former party at present predominant. Early in December, Gabriel Narutowicz, an engineer but a radical, was elected president. On Dec: 14 he entered office and-on Dec. 16 he was assassinated.

Jan 1, 1923

By Michael Tenenbaum, T. L. Joseph

Recent researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any substantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed. In some recent work, Diepschlagl found that, all other factors remaining constant, the degree of reduction of iron ores was much greater when carried out under pressure. Pressures as high as seven atmospheres were used. The degree of reduction was determined from the ferrous and ferric iron in the sponge iron. Results were obtained using both carbon monoxide and hydrogen at temperatures of 400°, 600° and

Jan 1, 1939

By Michael Tenenbaum, T. L. Joseph

Recent researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any substantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed. In some recent work, Diepschlagl found that, all other factors remaining constant, the degree of reduction of iron ores was much greater when carried out under pressure. Pressures as high as seven atmospheres were used. The degree of reduction was determined from the ferrous and ferric iron in the sponge iron. Results were obtained using both carbon monoxide and hydrogen at temperatures of 400°, 600° and

Jan 1, 1939

By Charles W. Wagner

A premature explosion might be described as an explosion that, occurs before the miner expects it. Notwithstanding that it is unexpected, a premature is generally within the miner's control. A hangfire explosion is a blast that occurs after the miner expects it,, and in all instances, except where the explosives or blasting accessories are defective, hangfire explosions are within the miner's control. Causes of Premature Explosions Generally, there are seven methods of shot-firing in anthracit,e mines; namely: (1) cap and fuse with dynamite, (2) fuse with pellet powder, (3) squib with black powder or pellets, (4) exploders and delays with dynamite or black powder, (5) exploders with dynamite, (6) delay ignitors with black powder or pellets, (7) electric squibs with black powder or pellets. Cap and Fuse.—This method of firing seems to produce the greatest number of premature explosions. This is not solely because of the method, but is the result of mispractices which are possible with this method of firing. The two most common mispractices followed with cap-and-fuse blasting are the firing of multiple holes and the use of short fuse.. In the firing of multiple holes by cap and fuse, investigations have shown that in nearly every instance where the miner was injured by this method of firing he remained too long at the face lighting the several fuses, so that the first shot went off before he could reach a place of safety. Such accidents could have been avoided either by accurate judgment by the miner of the relative lengths of the fuses or by the use of electric firing. Rules exist in nearly every mine forbidding the lighting of more than one hole at a time where the cap-and-fuse method of firing is practiced. Where it is desirable to fire more than one hole at a, time, electric firing should be used. It is difficult to understand why so many premature explosions result from the use of short fuses, inasmuch as the cost of fuse is practically a negligible item in the expense of a day's work. Notwithstanding this, however, we frequently find miners using short lengths of fuse in an effort to save one or two cents per hole, or about 15 to 20 # in a day. A practice

Jan 1, 1931

By William B. Phillips

The concentration of natural magnetites has been carried on in this country for several years, and more or less information has been collected on the subject. Various inventors, availing themselves of the magnetism which is inherent in such ores, have devised machines for separating the impurities from the ore by means of the electric current; and a greater or less degree of success has rewarded their painstaking and persevering efforts. We are now fairly in position to judge of the value of the process as applied to such material. It is not my purpose to speak of this matter further than may be required by the emergencies of the case. I shall assume that most engineers and metallurgical chemists are already acquainted with what has been done at the Chateaugay mines, at Mineville, at the Benson mines, at the Weldon and Ogdensburgh mines, and at Cranberry; although, at this latter place, there has not been so much done as we could wish. I shall not now speak of the various types of separators. From the time of William Fullarton, to whom was granted an English patent, in 1792, for separating iron-ore by the application of magnetic attraction, down to the present time, a great. many devices have been suggested, and a great many patents taken out for this purpose; but it is not necessary now to enter upon a discussion of their merits. Perhaps, at some future meeting of the Institute, after we shall have experimented further with some of the machines on the market, there may be an opportunity to contribute something to the current knowledge of the efficiency and economy of separating-machines. In this paper I propose to give, as briefly as possible, the results already reached in converting a non-magnetic ore into magnetic ore, and then concentrating it over a magnetic separator of the alternate-polarity type. I am aware of the work

Jan 1, 1896

By Henry Seltz, Cyril Wells, Hugh J. MacDonald

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940

By Henry Seltz, Hugh J. MacDonald, Cyril Wells

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940