Search Documents

By Rosewell H. Johnson

Discussion of the paper of ROSWELL H. JOHNSON, presented it the San Francisco meeting, September, 1915, And printed in Bulletin No. 102, June, 1915, pp. 1291 to 1294. WILLIAM A. WILLIAMS, San. Francisco, CaI.-A sliding. scale of royalties was proposed to the Department of the Interior in connection with the fixing of royalties to be charged upon oil leases made on the Osage Reservation in Oklahoma. The possibility of evasion and difficulty of enforcement required close inspection to satisfy all interests, particularly in connection with the exemption from royalty on oil to equal maintenance and interest on the junk. Mr. Johnson discusses the block method, the period method, and the cumulative method, and favors the adoption of the cumulative method with a proviso that the wells should be permitted to be pumped until the gross income is as low as the maintenance cost, which would mean exemption from royalty on the smallest wells. He recommends that depth be the variable factor upon which the sliding royalty is based and suggests that on partially developed territory in the Osage, the royalty be one-sixth for oil wells averaging less than 2,000 ft. in depth, one-eighth for wells from 2,000 to 3,000 ft., and one-twelfth above 3,000 ft.; for the rest of the Osage he suggests one-eighth above 2,800 ft. and one-twelfth below that depth. The net result, if Mr. Johnson's suggestions had been accepted in the Osage, would have been to reduce the then existing rate of royalty and considerably increase the cost of administration. The difficulties in determining the size of wells to be exempt and the possibility of obtaining oil at different depths in the same well might lead to complications which are avoided by charging a flat royalty as now universally charged throughout the United States. It is not uncommon to reduce the royalty when the production of the wells becomes unprofitable at an existing rate of royalty, accomplishing very much the same results as Mr. Johnson has attempted to accomplish by the cumulative royalties, and probably in a manner far more satisfactory to the operator and the lessor. A. C. MCLAUGHLIN, San Francisco, Cal.-The net revenue of the well depends, first, on the cost of production; second, on the amount of oil produced; therefore it would be impossible under Mr. Johnson's system to set a royalty which would be fair to all concerned. If it is impossible to set it at the beginning, it is certainly further impossible to do it from day to clay. I think it is entirely impracticable of application.

Jan 12, 1915

By L. G. Huntley

The occurrence of oil or "tar" in Mexico was mentioned as early as the seventeenth century by Friar Sagahun, who gives the Indian name "chapopote," by which these asphalt seepages are still called. This asphalt was apparently used, as it has been used by primitive people in many parts of the world, in religious ceremonies and for medicinal purposes. Travellers also report that the ruins in Yucatan and the pyramids in southern Mexico show traces of the use of "chapopotel' as a building cement.l DeGolyer says that the first attempt to exploit oil or gas in Mexico in a commercial way is shown by the records of the Memoria de Fomento of 1865, when permission was granted to a Senor Ildefonso Lopez to exploit the deposits of petroliferous substances in the San Jose de las Rusias area in the State of Tamaulipas. Other concessions follow, and probably refer to surface seepages which occur in that district. This was several years after the discovery of oil in Pennsylvania. In 1868, a well 125 it. deep was :drilled by a company organized in Mexico City, in what is now known as the,, Furbero district, and a little oil was refined there. In 1873, residents of Tampico denounced seepages along the Tamesi River, and asphalt was mined near Tempoal in the Canton of Tantoyuca. No drilling was attempted. But between 1880 and 1883 several shallow wells were drilled for oil in Mexico, two of them being near the present Potrero de Llano field west of Tuxpam. The wells were drilled by a Boston company with Canadian rigs, and are said to have reached a depth of about 400 ft., while one is reported to have flowed. Several other abortive attempts were made to drill for oil between 1885 and the beginning of the present century, about which time the Mexican Petroleum & Liquid Fuel Co., Ltd., in which Cecil Rhodes was interested drilled 24 wells unsuccessfully, several of them as deep as 1,500 ft., in the State of Vera Cruz. Also Messrs. Doheny and Canfield of California pur-

Jan 1, 1916

By B. H. Sage, W. N. Lacey

An apparatus is described for the measurement of the pressure-volume-temperature relations of pure substances, simple mixtures and complex mixtures with an over-all absolute uncertainty, which is usually not more than 0.2 per cent. The equipment is suitable for studies in the gaseous, two-phase, and liquid regions. The behavior of such systems may be investigated at pressures as high as 10,000 lb. per sq. in. for temperatures between 70 and 600 F. The methods of measurement and the construction of the apparatus are described in some detail. The measurement of the volumetric behavior of multicomponent systems requires the simultaneous measurement of the pressure, volume, temperature and weight of each component of the system. In the present apparatus a sample having constant weight is investigated at a number of independently controlled pressures and temperatures, therefore it is necessary only to establish the weight of each component added before a given set of measurements. This method is in distinction to that in which the total volume remains constant and the pressure is varied by addition or removal of material, the system having variable weight. An objective in the design of the apparatus to be described was to develop equipment that would yield results involving no uncertainties larger than 0.25 per cent throughout the range of pressures from 150 to 10,000 Ib. per sq. in. at temperatures between 70" and 600" F. Although this over-all absolute uncertainty of measurement may not appear to be small, it necessitated care in the plans for control and measurement of each of the fundamental variables. In general, any uncertainty greater than 0.05 per cent in the pressure, volume, absolute temperature or weight of each component was considered undesirable; therefore the attempt was made to obtain a precision of measurement in each case such that the absolute uncertainty would be only half this amount except in certain regions near the ends of the experimental range of the variable under consideration.

Jan 1, 1940

By W. N. Lacey, B. H. Sage

An apparatus is described for the measurement of the pressure-volume-temperature relations of pure substances, simple mixtures and complex mixtures with an over-all absolute uncertainty, which is usually not more than 0.2 per cent. The equipment is suitable for studies in the gaseous, two-phase, and liquid regions. The behavior of such systems may be investigated at pressures as high as 10,000 lb. per sq. in. for temperatures between 70 and 600 F. The methods of measurement and the construction of the apparatus are described in some detail. The measurement of the volumetric behavior of multicomponent systems requires the simultaneous measurement of the pressure, volume, temperature and weight of each component of the system. In the present apparatus a sample having constant weight is investigated at a number of independently controlled pressures and temperatures, therefore it is necessary only to establish the weight of each component added before a given set of measurements. This method is in distinction to that in which the total volume remains constant and the pressure is varied by addition or removal of material, the system having variable weight. An objective in the design of the apparatus to be described was to develop equipment that would yield results involving no uncertainties larger than 0.25 per cent throughout the range of pressures from 150 to 10,000 Ib. per sq. in. at temperatures between 70" and 600" F. Although this over-all absolute uncertainty of measurement may not appear to be small, it necessitated care in the plans for control and measurement of each of the fundamental variables. In general, any uncertainty greater than 0.05 per cent in the pressure, volume, absolute temperature or weight of each component was considered undesirable; therefore the attempt was made to obtain a precision of measurement in each case such that the absolute uncertainty would be only half this amount except in certain regions near the ends of the experimental range of the variable under consideration.

Jan 1, 1940

By H. C. Rogers

It has been shown previously'- 3 that when a mild steel or iron is charged with hydrogen, the normally observed yield point is eliminated or considerably

Jan 1, 1960

By B. H. Sage

AN apparatus is described for the measurement of the pressure-volume-temperature relations of pure substances, simple mixtures and complex mixtures with an over-all absolute uncertainty, which is usually not more than 0.2 per cent. The equipment is suitable for studies in the gaseous, two-phase, and liquid regions. The behavior of such systems may be investigated at pressures as high as 10,000 lb. per sq. in. for temperatures between 70° and 600° F. The methods of measurement and the construction of the apparatus are described in some detail. The measurement of the volumetric behavior of multicomponent systems requires the simultaneous measurement of the pressure, volume, temperature and weight of each component of the system. In the present apparatus a sample having constant weight is investigated at a number of independently controlled pressures and temperatures, there-fore it is necessary only to establish the weight of each component added before a given set of measurements. This method is in distinction to that in which the total volume remains constant and the pressure is varied by addition or removal of material, the system having variable weight. An objective in the design of the apparatus to be described was to develop equipment that would yield results involving no uncertainties larger than 0.25 per cent throughout the range of pressures from 150 to 10,000 lb. per sq. in. at temperatures between 70° and 600° F. Although this over-all absolute uncertainty of measurement may not appear to be small, it necessitated care in the plans for control and measurement of each of the fundamental variables. In general, any uncertainty greater than 0.05 per cent in the pressure, volume, absolute temperature or weight of each component was considered undesirable; therefore the attempt was made to obtain a precision of measurement in each case such that the absolute uncertainty would be only half this amount except in certain regions near the ends of the experimental range of the variable under consideration.

Jan 1, 1939

By C. L. Siebenthal

C. E. SIEBENTHAL, ? Washington, D. C.-From being one of the most maligned of metals-a veritable bugaboo-cadmium has almost overnight become respectable, though its slender claim to respectability rests almost wholly on the possibility of its substitution for tin. Preliminary to any campaign for such substitution, particularly for enforced substitution, the possible supply of cadmium should he determined as closely as possible; for that reason the statistical inquiry of which this paper embodies the results was undertaken. Production Cadmium is marketed in two forms, as metallic cadmium, in sticks or bars, and as cadmium sulfide, the pigment. The metal has found its greatest field of use in this country as a component of an easily fusible alloy that is used in automatic fire extinguishers. The sulfide is .used to some extent in paints but chiefly to give color and luster to glass and porcelain. The metal was first made in this country by the Grasselli Chemical

Jan 12, 1918

By V. K. Zworykin

THROUGHOUT its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes; it. has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron. Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction -at the very best a tenth-of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. To overcome it, a different imaging medium must be employed. The existence of such a medium became evident when it was demonstrated' that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed, Furthermore, although a wave length may be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light: Actually, the electron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. THE ELECTRON MICROSCOPE Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the electrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

By Robert Franke

(Butte Meeting, August, 1913.) IN view of the prominence which the conical mill has attained in the fine-crushing field .within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. . Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the immediately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years' operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each. liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which. follow rolls crushing to 0.5 in.

Jan 7, 1913

By K. Hanumantha Rao, A. Nayak, . K. S. Narasimhan, S. N. Mahapatra

Selective flocculation studies carried out with iron ore tailings generated at Kudremukh iron ore plant indicate that a concentrate containing 63% iron can be obtained from the tailings containing 34% iron with around 60% recovery. This opens up the possibility of recovering most of the iron lost in the tailings generated at 2 kt/h (2200 stph) while processing 22 Mt (24 million st) ore per year. This would mean that the productivity could increase by around 50%. In these studies, it has been established that caustic degraded tapioca starch is a most effective agent for selective flocculation. While potato starch after caustic degradation can also be used, neither the parent starch nor the amylopectin compound is as effective.

Jan 1, 1986

By R. H. Hopkins, R. W. Kraft

X-ray and metallographic analysis reveal that the preferred cryslallograPhic relationships in direc-tionally solid~fied Pb-Sn eutectic specimens can be stated: interface growth direction, Experiments in which tin single-crystal seeds were used to nucleate the eutectic demonstrate that the normal lamellar structure observed at steady state can be forced to break down initially to a semide-generate structure when the crystallograPhic direction of the tin seed does not lie within the preferred eutectic interface plane. A normal structure eventually develops by preferred grain growth. X-ray topo-graphs and rocking curves substantiate that the perfection of eutectic samples increases as growth proceeds until steady-state conditions prevail. RECENT years have seen substantial progress made in the understanding of eutectic solidification through both intensive theoretical1'' and experimental investigations (see Ref. 7 for a review and extensive bibliography of both aspects). Several important observations concerning the nucleation and growth aspects of binary eutectic solidification have been brought to light. Briefly some of these include the nonrecipro-cal nucleation of one phase upon another,'j9 the tendency for a specific low-index direction of one or both phases of the eutectic to be aligned in the growth direction during unidirectional solidification,'0711 and the production of lamellar microstructures having a preferred interface plane between "11-13 phases. Questions quite naturally arise as to the mechanism by which preferred grain growth evolves during eutectic solidification and what relationships (if any) connect the initial nucleation of one phase upon another with the preferred growth directions and interface planes observed after a few centimeters of growth in many systems. This study was initiated in an attempt to answer these questions. An experiment was devised in which both the nucleation and growth steps in the crystallization of a binary eutectic, Pb-Sn, could be correlated with subsequently developed eutectic morphology and crystallography. This was accomplished by nucleating the eutectic upon a tin single crystal seed and then causing the eutectic to grow from the seed by directional freezing. The morphology of the structures produced in this manner was then monitored metallographically and the orientation relationships and substructural perfection determined by X-ray analysis. The information thus ob- tained was correlated to the growth history of the samples. EXPERIMENTAL DETAILS The eutectic of composition 38.1 wt pct Pb and 61.9 wt pct sn14 was prepared by accurately weighing lead and tin of 99.999+ (from ASARCO and Lytess Metals and Chemicals, respectively), melting in a clean Pyrex beaker under an argon blanket, and casting into the proper crucible for resolidification as described below. Tin seeds were grown by the method of ~halmers," saw-cut, oriented by the Laue method, and soldered to the pull rod of the Czochralski puller. All seeds were given a final electropolishing (to assure the removal of any deformed material from the cutting operation) and acetone degreasing immediately prior to the nucleation experiment in which they were to be used. Eutectic samples were unidirectionally solidified in a horizontal graphite boat1' or by pulling from the melt16 with tin (or graphite) seeds. A flowing argon atmosphere was employed in all experiments and growth rates and temperature gradients, constant for a given run, varied from 2 to 4 cm per hr and 8" to 15°C per cm over the course of all the experi-

Jan 1, 1969

By R. F. Lynch, J. D. Wood

The Al-1.0 pct Mg alloy 565 7 was studied using optical microscopy and electron microprobe X-ray analysis. Constituent particles were found to exist inter-dendritically in the as-cast material in a region of precipitate free a -aluminum. Five phases besides a fine precipitate and a-Al were identified in the cast structure: Fel3, Fe2Al7, Mg2Al3, CUMgAl2, and Cu2FeAl7. Thermal treatments conducted for 100 hr at 1180°, 1130°, 1080°, 1030°, 980°, and 880° F revealed a general dissolution and spheroidization of the in-terdendritic constituent network observed in the cast structure. The principal constituents present in the thermally treated structures were FeAl3 and Fe2Al7 with the relative amount of Fe2A17 to FeAl3 increasing with a decrease in the treatment temperature. The phases Present in the wrought structure were identical to those observed after the thermal treatments, with the constituent particles strung out in the direction of rolling. ALLOY 5657 is a nonheat-treatable commercial purity Al-1.0 pct Mg alloy utilized extensively because of its bright finishing characteristics. This investigation was conducted to determine the constituents present in 5657 alloy, and to study the effect of extended thermal treatments on morphology. Numerous studies have been carried out to establish the equilibrium diagrams for various aluminum systems,1-3 with phase identification based on X-ray analysis, morphology, and the etching response of relatively large particles. Phragmen4 conducted a study of the phases in aluminum eutectic systems and compiled a "corrected" table of etching responses, drawing on his work plus that of Schrader,5 Keller and Wilcox,6 and Mondolfo.7 A review of the original work of Keller and Wilcox, and Mondolfo, which was concerned with the constituents found in commercial alloys, reveals that in numerous cases their etching responses differ from those reported by Phragmen and from each other. These inconsistencies may occur because a specific constituent will react to a given etch in a varying manner depending upon its size, the elements dissolved in the phase, the other constituents surrounding a phase, and the solute content of the matrix. Work with a commercial orientation was conducted on alloys 2024 and 3003 by Sperry8,9 and on alloy 3003 by Barker,10 where the relationship between the phase diagram and the nonequilibrium structure of an alloy was examined. Backerud11 investigated the A1-Fe binary system and found that at high cooling rates the equilibrium eutectic reaction forming a-A1 and FeA13 is replaced by another lower temperature eutectic reaction forming a-A1 and metastable FeAl6, a constituent first identified by Hollingsworth et al.12 Most of the above mentioned studies were conducted on materials having a significantly greater alloy content than 5657 alloy, where the relatively small size and sparse distribution of second phase particles hinders the process of identifying constituents. EXPERIMENTAL PROCEDURE Material with a composition as given in Table I was examined in the as-direct chill cast, hot rolled and cold rolled conditions, and after thermal treatment of the cast structure. Thermal treatments were terminated by a water quench. Microscopic examination was conducted under various lighting conditions following the application of standard etchants as specified in Table 11. A semi-quantitative electron microprobe X-ray analysis was conducted for Al, Mg, Fe, Cu, Si, Zn, and Ti. RESULTS AND DISCUSSION Microstructure of the As-Cast Material. Particles of second phase material were found to exist inter-dendritically, principally in regions of precipitate free a-Al, as illustrated in Fig. 1. Adjacent to the ingot edge was a region of inverse segregation, resulting in an increased amount of second phase material containing large sized particles which aided in phase identification. Phase Identification. Cast Structure. Five phases besides a-Al and a fine precipitate were identified using optical microscopy and electron microprobe X-ray analysis, as presented in Tables II and III, respectively. FeA13 and Fe2A17 are often found with Fe2A17 forming a sheath around the core of FeAl3, resulting from an incomplete peritectoid reaction. These phases have a nearly identical appearance under white light, although they are easily differentiated under crossed polarizers, as characteristically illustrated in Figs. 2(a) and 2(b), respectively. Microprobe analysis con-

Jan 1, 1970

By J. Campbell

Various models are discussed for the evaluation of the negative pressures which may occur in solidifying materials which exhibit various deformation modes: elastic-plastic, Bingham, viscous, or creep flow. The inadequacy of the previously proposed elastic-plastic solution for solidifying metals is revealed by comparison with the more reliable creep results which are given graphically for aluminum, copper, nickel, and iron. The maximum tensions experienced in the liquid phase of solidifying spheres ranging in size from large castings to submicron powders are in the range from —10' to —105 atm for these metals. THERE has been much recent interest in the negative pressures associated with the volume change on solidification and in the possibility of the occurrence of cavitation. Considering the freezing of a highly supercooled liquid, an attempt to evaluate the stresses in the liquid ahead of the rapidly moving solidification front has been made by Horvay1 on a microscale and by Glicksman2 on a macroscale. In a casting of a wide freezing range alloy, the pressure differential due to viscous flow of residual liquid through the pasty zone has been discussed by Piwonka and Flemings,3 In a previous publication4 the author has attempted to estimate the negative pressure occurring in the residual liquid of a spherical casting, employing an elastic-plastic model to describe the collapse of the solidified shell under the internal tension. An earlier model assuming a rigid shell was shown to be inaccurate by many orders of magnitude. The elastic-plastic model is critically reviewed here, and other models are developed which are thought to be more closely related to metals and other materials near their melting points. The spherical geometry (Fig. 1) is chosen because the highest shrinkage pressures would be developed, although the analyses are readily adaptable to cylindrical geometry. A parallel sided casting experiences little internal tension because of the relatively easy dishing inward of the sides. (This commonly observed phenomenon has previously been attributed solely to atmospheric pressure.) Furthermore, small regions of confined liquid in a large solidified volume of a casting approximate reasonably well to spherical geometry. ELASTIC-PLASTIC MODEL The author has shown4 that as solidification proceeds the internal hydrostatic tension builds up until the elastic limit of the shell is exceeded. At this point the internal pressure is closely -2Y/3. Subsequently a plastic zone spreads from the inner surface toward the outer surface of the shell. When the whole casting is deforming plastically a rather more generalized analysis taking account of the externally applied pressure PA + 2y/b gives the internal pressure as: P = Pa + 2y/a + 2ys/b - 2 Y In(b/a) [1] The 2y/a and 2ys/b terms result from the tendency of the liquid-solid and solid-vapor interfaces to shrink, reducing their energy, and thereby helping to collapse the solid phase and compress the liquid phase. The 2y/b term would be important only for powders. The last term arises because of the plastic restraint of the solid, resisting collapse and so effectively expanding the residual liquid. From Eq. [I] it is easily shown that there is a minimum in the pressure at the radius amia= y/Y [2] which is of the order of 103K for the metals aluminum, copper, and iron, and corresponds to the minimum pressure Pmin = 2 Y[l-ln(bY/y [3] The results of a fully worked out elastic-plastic solution are given in a previous reporL4 The main criticism which may be leveled at this analysis when applied to metals at their melting points is the strong dependence of the yield stress on the strain rate. The strain rate varies with both solidification conditions (e.g., whether chill-cast or slowly cooled) and during solidification, as is indicated in the following section. Thus an appropriate choice of Y is very arbitrary. Before proceeding to a discussion of models which are strain-rate-dependent, it is necessary to evaluate the strain rate as a function of the rate of solidification. SOLIDIFICATION RATE Various empirical relations have been deduced5 for the rate of thickening of the solid shell by pour- out tests on partially solidified spheres. These, however, are unsatisfactory for our purposes since they become very inaccurate when the liquid core is very small. A theoretical approach is therefore necessary, and some solutions are set out below. Making the assumptions of constant surface temperature of the casting during freezing, no superheat, and a material freezing at a single temperature, Adams8 deduces the approximate solution: which becomes when b » a: Employing a semiempirical approach vallet6 finds:

Jan 1, 1969

By Richard I. Petritz

A brief review of today's processing of integvated circuits is given. The major trends in the development of advanced integvated electronics are identified as 1) the broadening of the integvated circuit concept to a large class of circuit function, 2) the processing of more complex circuits within relatively small chips of silicon, and 3) the processing of very large electronic functions on complete slices of silicon. This latter trend, called array technology, is then developed in detail. Emphasis is given to defining the key tech-nological problems. Current progress being made is illustrated. THIS paper will endeavor to identify the major trends in advanced integrated electronics technology. One of these, array technology, will be developed in some detail. The array technology discussion will identify the key problem areas. Since it is the scope of the entire meeting' to present specific progress in the science and technology of integrated electronics, we shall indicate general directions being explored rather than discuss comprehensively solutions to the problems. In order to set the stage for the discussion of future trends in integrated-electronics technology, let us briefly compare the processes by which circuits are fabricated through discrete-device technology with that of integrated circuits technology. The reader is referred to the December 1964 issue of Proceedings of IEEE2 for a comprehensive review of integrated electronics. The article3 by Jay Lathrop is an excellent discussion of integrated-circuits technology. A discussion of the history of semiconductor technology is contained in Ref. 4. A) Current Status of Integrated Electronics. Fig. 1 (top) shows the process by which circuits are constructed from discrete devices. Key points are: 1) Slices containing large numbers of transistors or diodes are processed separately. 2) The slices are scribed into small chips (on the order of 15 mils on a side is about as small as can be conveniently handled) each chip containing one transistor. 3) Each device is specified separately—circuit -function specs are derived largely from device specs. 4) Circuits are formed by connecting together the discrete devices. 5) The number of circuit connections required is approximately equal to the number of devices. 6) There are potentially many more discrete devices per inch2 of semiconductor—only our lack of ability to handle them in discrete form prevents us from going to several orders of magnitude higher density iin Fig. 1, 400,000 transistors are discussed at 1.5 mils on a side). The bottom part of Fig. 1 illustrates the integrated circuit process. Key points are: 1) On the same slice of silicon, transistors, diodes, and resistors are processed grouped to do a complete circuit function. 2) While still in slice form, the components are interconnected into circuit functions by an evaporation process, eliminating the need for separate interconnection steps later. Dramatic improvements in cost and reliability are realized. With a simple flash of metalization thousands of interconnections are reliably made. 3) The slices are scribed into chips which contain complete circuit functions. 4) The circuit functions are specified-not each component in the circuit. This important point was missed by some of the early opponents to integrated circuitry. They argued that, with device yields at x pct, integrated circuit yields would be pct, where n is the required number of devices to make a circuit. This argument leads to extremely low yields for integrated circuits. The fallacy of the argument is that in integrated circuits each device is not specified separately. Furthermore, since a device is forever integrated into a specific circuit function, it need meet only the requirements for that particular function. Discrete devices, on the other hand, are tightly specified so that they can be applied to a variety of circuit functions. 5) Extremely high packing densities are achievable because one need only make the basic devices as large as the circuit demands. Their size is not dictated by handling requirements. A current example

Jan 1, 1967

By W. C. Roberts-Austin

The subject with which the Council of the American Institute of Mining Engineers has entrusted me is one of much interest. It has been so admirably treated in America by Prof. Carl Barus* that I should have hesitated to deal with it had not the adoption of pyrometric methods in England recently occupied much attention, especially in relation to metallurgical industries and research. I shall endeavor to show what is the present state of our knowledge of practical pyrometry by briefly tracing the history of the efforts which have been made to measure high temperatures. This paper will, therefore, be limited to the consideration of those forms of appliance which have either marked distinct stages of advance, or have remained in use with more or less modification through a considerable range of time. The earliest pyrometers were essentially thermoscopes, and although their graduation presented great difficulties, their importance as affording a means for the measurement of high temperatures has been recognized for centuries. It would be difficult to illustrate this better than by a brief record of the testimony which has from time to time been offered by those who have had to apply the heat of furnaces in research or in industry, and it is mainly for the sake of the light incidentally thrown on the progress of both that the following historical notes are offered. In the eighth century, Geber, the chemist, wrote a treatise on furnaces, and showed that he was familiar with many and varied means of applying heat; but he points to the difficulties that are met with in conducting operations at high temperatures, which he attributed to inability to measure heat, his actual words being: " sed quoniam non est res ignis, quae mensuari possit." t

Jan 1, 1894

By C. N. J. Wagner, E. N. Aqua

The bee alloys of the terminal solid solution of rhenium in niobium were investigated by X-ray diffraclion methods. The analysis of the broadening of the powder pattern peaks from the niobium-rich alloys, cold-worked by filing, showed evidence for faulting on (211) planes. The alloys with larger rhenium concentrations were brittle, and fractured when filed. The analysis of the shapes of the diffraction profiles from powders produced by hammering with steel plates) of these brittle alloys indicated that the broadening was due predominantly to platelets bounded by clibe planes. This result was consistent with the Laue patterns from single-cleazlage facets which showed evidence for clearage fracture on {100} planes. The influence of faulting on the mechanical properties of face-centered cubic (fcc) metals and alloys, i.e., how faulting affects the various dislocation configurations in fcc metals, is well-known.' The important question is whether or not faulting occurs in body-centered cubic (bcc) metals and alloys, and, furthermore, if faulting does occur, to what extent it affects the mechanical properties. Theoretical calculations indicate that the stacking-fault energy is rather high in most bcc metals.2 The results of sev-eral studies using transmission electron microscopy have indicated that faults are present in well-annealed and lightly deformed bcc metals and alloys, such as tungsten,3 vanadium,4 and Mo-Re alloys.5,6 These faults, as have been observed, may be stabilized by the presence of interstitial (C,N,O) atom segregation to the extended dislocations. In addition, there is considerable X-ray diffraction evidence for faulting in bee metals,7-8 using the same techniques that were successful for the study of faulting in fee metals and alloys.7 This X-ray diffraction method is currently the only technique applicable for the investigation of faulting in metals with high stacking fault energies, i.e., when severe amounts of deformation are required to produce sufficient amounts of faulting to be detectable by X-rays. The thinned films of heavily deformed metals will become opaque in the electron microscope due to the high dislocation densities present. In a previous investigation of faulting8 in bee metals of group Vb and VIb, the authors observed that niobium was ductile when filed at room temperature, and showed the highest density of faults on the (112) family of planes. A niobium-base alloy system was therefore chosen to study the effect of alloying on the occurrence of faults in a bcc alloy. There is a large range of terminal solid solubility of rhenium in the alloys of the bee refractory metals. All of the Group VIb-rhenium alloys, i.e., Cr-Re, Mo-Re, and W-Re, exhibit solid solution hardening without loss of ductility.9 In fact, the ductility reaches a maximum for alloys with compositions near to the limits of solubility. This enhanced ductility has been attributed to the lowering of the stacking-fault energy in the alloy; i.e., the increased amounts of twinning provide an additional mode of deformation, resulting in the observed high ductility.' Because of this demonstrated effect of rhenium in bee alloys, it was decided to study a series of alloys of Nb-Re. Using the same X-ray diffraction methods as described in the previous investigation,' one is able to identify the possible causes of broadening of the powder pattern peaks, e.q., particle size, microstrains, stacking faults, and/or twin faults. The separation of these various contributions to the measured peak shape is accomplished by the Warren-Averbach analysis.7 I) EXPERIMENTAL PROCEDURE A series of seven bee solid solution alloys containing from 2.5 to 21.5 at. pct Re (remainder niobium) were prepared at the General Electric Research Laboratory. Buttons, weighing 25 g, were alloyed from electron-beam-melted niobium chips and random rhenium sheet by arc melting in a water-cooled copper crucible, under an argon atmosphere. The buttons were inverted and completely remelted to promote homogenization. The nominal alloy compositions are listed in Table I. Samples of the cold-worked alloys were obtained by filing to produce a powder for the X-ray study. Alloys too brittle to be filed were hammered with steel plates. The resultant filings or brittle impactings were screened through 150-mesh classifiers and compacted to the required shape for the diffractometer holder. The X-ray diffraction peaks were automatically recorded by fixed time counting at uniform 28 intervals, or by continuous registration with a ratemeter. In all cases, the (110)-(220) and (200)-(400) pairs of peaks and the (211), (310), (222), and (321) reflections were measured on a GE-XRD5 diffractometer using CuKa radiation with nickel filter or MoKct radiation and a LiF monochromator in the diffracted beam. The first part of the data reduction, completed with the aid of a series of programmed computations,10 was the analytical resolution of the Kol component of the diffraction profile. Subsequent computations were then made with reference only to the resolved Kol peak shape. These included the measurement of the

Jan 1, 1967

By Herbert R. Hanley

THE One Hundred and Twenty-sixth meeting-of the Institute, held in San Francisco, Sept. 25 to 29, 1922, was a success in every way. Character-istically, San Francisco presented climate suited, to the occasion, while the Committees on Arrangements left nothing undone that would contribute to the interest and entertainment of the members and their wives. There was a registration of over 230, and all sections, save three, were represented. In the technical meetings, under the leadership of Albert Burch in the mining session and C. W. Merrill in the milling session, the greatest interest was manifested in ore-hunting geology and modern ore-dressing methods. The general geologic phase developed numerous discussions and had for its aim the study and correlation of known data and the application-of these to the finding of commercial orebodies. The geologic features of the Comstock and their significance to the development of the present orebodies were discussed. This brought out matters of much technical interest as well as those of romantic nature in the history of the early life of that camp. The profitable application of modern milling methods to ores, non-commercial a short time ago, was discussed with much interest. The recent work on the Comstock ores occupied a conspicuous part in these discussions. Basic principles delineated by mathematical study of mechanical devices for the milling of ore came in for a prominent part in the program as well as the physical-chemical side of the processes devised for the winning of precious metals as a profit.

Jan 11, 1922

For the year ending February, 1919 PRESIDENT SIDNEY J. JENNINGS, NEW YORK, N. Y. PAST PRESIDENTS L. D. RICKETTS, NEW. YORK, N. Y. PHILIP N. MOORE, ST. Louis, Mo. FIRST VICE-PRESIDENT C. W. GOODALE BUTTE, MONT. TREASURER GEORGE D. BARRON, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 2, 1919

By B. S. Norris, Charles R. Austin

The stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals' has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.* It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. $ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, wlletller deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of deformation. With this information, a study of the rates of work-

Jan 1, 1938

By B. S. Norris, Charles R. Austin

The stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals' has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.* It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. $ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, wlletller deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of deformation. With this information, a study of the rates of work-

Jan 1, 1938