Search Documents

By Peter F. Weiss

INTRODUCTION Austro-American Magnesite Co. of Radenthein, Carinthia, Austria, is a wholly owned subsidiary of General Refractories Company, Bala Cynwyd, USA, and has been incorporated since 1908. The raw material basis is the magnesite mine on Millstatt Alp, located in the mountains near Radenthein at an altitude of 1500 m above sea level. The mined crude magnesite is crushed in a surface crushing plant to minus 35 mm and consequently hauled to the processing plant in the valley by means of a cable conveyor of 7.5 km length. The annual production of 350,000 mt is accomplished with 20 supervisors and 122 workers (of those 60 are in the mine). The labor requirement for block caving is 0.2 man hr/mt, corresponding to an output of 40 mt/man/ shift. GEOLOGY The rock in this area mainly consists of crystalline type schist. There are mostly coarse crystalline garnet mica schists with varying mineral concentrations, and to a lesser degree, some deposits of amphibolite and marble. This petrographically rather homogeneous rock is divided into numerous different tectonic units (covers and scales). The magnesite deposit itself is a foreign body that also has been tectonically inserted. The ore body has a length of 600 m, is 450 m deep, and has a thickness of 60 m on average, varying substantially however, The contact with the accessory rock is very precise. The deposit 1 = ore body, 2 = previous open pit, 3 = caved in area, 4 = block under excavation, 5 = land slide consists of coarse crystalline magnesite in excess of 90 per cent. The few impurities consist of dolomite and talc. The lower part of the deposit is inclined parallel with the schists at approx. 40 degrees. In profile it can be seen, however, that the upper part of the deposit has been tilted over. This is a result of a post-glacial land slide reaching from the bottom of the valley at 1400 m above sea level to the peak of the mountain at 2100 m above sea level. Due to this land slide, with horizontal movements of up to 100 meters, as well as older tectonic events, the rock was crushed to a vast extent. Through mining, the land slide was reactivated; about 40 million cubic meters of rock slowly flow downhill almost like a plasticized mass. Near the surface, the rock is completely crushed and resembles a glacier rupture zone. This renders the originally impermeable rock completely water permeable so that practically all of the annual quantity of 1000 to 1100 mm of precipitation permeates the rock and flows down into the mine. The carbonate rock turns into the preferred aquifer. From 1700 to 2600 cubic meters of water have to be pumped from the mine daily. On one hand, additional problems are caused by the water in the mine, on the other hand we have learned to make use of the down- hill pressure forces to improve the crushing process during block caving. The boundary of the downhill shearing zone moves downward as mining goes deeper.

Jan 1, 1981

By Norman F. Schulz

Relative fineness is an important characteristic of iron ore balling feeds. It is frequently expressed in terms of the Blaine Number which is determined by standardized permeametry procedures. Inconsistencies in Blaine Number specifications for balling feeds from different sources prompted an investigation of permeability methods. A revised procedure for permeametry tests was developed for use with conventional apparatus that yields an Effective Blaine Number which is similar to the Standard Blaine Number except that it more accurately describes the effective fineness of the actual test sample.

Jan 1, 1980

By T. C. Poulter, B. M. Caldwell, D. E. Brink

The flash X-ray has been used more than a decade to study the configuration of the jet from a shaped charge. The high-speed, rotating-mirror smear camera has provided time-distance graphs of detonations and shock fronts in transparent materials, and the high-speed framing camera has given pictorial representations of the progress of explosive phenomena. Adequate means for measuring the paths and velocities of all parts of the shaped-charge cavity Iiner during the collapse phase have not existed heretofore. A technique enabling the single-lens framing camera to make stereoscopic photographs of the cavity liner while it is collapsing has been developed. Analysis of this photographic record gives the directions and velocities of various parts of the Iiner surface, permitting direct quantitative measurement where this has previously been impossible. Significant improvements in shnped-clrarge design are expected to result. INTRODUCTION The familiar oilwell jet perforating charge, generally referred to as a "shaped charge", is related to the Mun-roe charge first described by C. E. Munroe in 1888 and later by Neumann in 1910. It differs in construction from the Munroe charge in that its cavity is lined with some inert material (usually metal)', and it differs in performance by projecting a fast jet of dense liner material against the target instead of a stream of expanding detonation products. Fig. 1 represents a typical shaped charge in axial cross section. The charge is circularly symmetrical about its longitudinal axis. The cavity at the right is lined with metal, usually copper; and, with the exception of air, the liner is otherwise completely empty. High-explosive material is intimately in contact with the convex surface of the liner and extends in the other direction to the booster. This is a pellet of high explosive having somewhat different characteristics and serves to couple the detonator to the main charge. When the detonator is fired, a small hemispherical reaction zone of very high temperature and pressure occurs at its output end. The booster responds, adding its own latent energy to the reaction, thereby initiating the main charge. The reaction progresses throughout the main charge at a velocity of 7 to 8 mm/microsecond until all the explosive material has reacted. With a reaction pressure of about 160,000 atm, the surrounding material is moved rapidly away from the high-pressure zone. As the detonation proceeds along the cavity liner, moving from apex to edge, the liner is collapsed toward the axis of the cavity, where liner material from all parts of the concave surface converges. A zone of extraordinarily high pressure results. with only one escape path—outward along the axis. The particles from the liner, thus, become a jet of very high velocity, with a density characteristic of the material from which the liner was made. The kinetic energy of the jet, concentrated in a small area of the target, has great penetrating power. It overcomes the strength of any target, and the target material crumbles or deforms plastically to escape from the path of the jet. An unlined cavity charge, on the other hand, projects a turbulent body of hot gaseous material against a target and erodes the exposed surface. With equal quantities of explosive, the penetration effectiveness of an unlined charge is a small fraction of that of a lined charge. Given an explosive charge with a detonator at one end and an axially symmetrical metal-lined cavity at the other, one has a perforator of considerable potency. To maximize the penetrating and other desirable effects,

By R. Laird Auchmuty

FOREWORD THE A. I. M. E. Subcommittee on Bituminous Mining has been trying for several years to secure the information that was collected by the Marquette Cement Manufacturing Co. on the subsidence of its property caused by mining coal beneath it. The Marquette company was willing to have these data used, but it was impossible to obtain them because the records had been filed away. About two years ago these records became available and the engineering data presented herewith were compiled from them by R. L. Auchmuty, assisted by L. E. Young, who was connected with the collection of the information. On account of the cost, it is impossible to reproduce all of the data here, although the original information is on file with the records of the Committee on Ground Movement and Subsidence. The accompanying charts show representative and average data and give only the engineering information with enough description to tell how it was obtained. It is hoped that all of those connected with the original case will participate in the discussion that this will bring forth. HOWARD N. EAVENSON, Chairman, Subcommittee on Bituminous Coal Mining.

Jan 1, 1931

By A. D. Marlin, A. J. Gentile, E. F. Jordan

Metallurgical changes in SAE 52100 ball-bearing components resulting from overload testing are described. Changes in microstructure, hardness, and resiclctal stresses crre discussed zuitlz re.ference to material cleanliness obtained by various steel-melting practices and are compared with work by otlzer investigators. Evidence is presented to show that the initialion and development of microstruc-tural alterations are characterized by two separate reactions: the appeavance of a "dark etchingJ' constituent, and "gray lines" or a light etclzing constituent. The dependency of these tzvo reactions on material cleunliness, running tirne, and contact stresses is discussed and a failure mode related to material cleanliness and microstructural transformation is proposed. THE study of ball- and roller-bearing contact fatigue has been paced by a strong emphasis on bears ing application performance. Particular attention has been paid to conditions that effect the spalling-type failure that is characteristic of rolling contact fatigue in through-hardened components. Some of the conditions investigated are lubrication and atmosphere,1-3 material characteristics and finish,475 and speed and design fa~tors."~ A typical spalling-type failure is shown in Fig. 1. The arrow shows the motion of the ball relative to the inner-ring race surface. The leading edge of the spall is usually sharper than the trailing edge. The race surface near the trailing edge also shows small dents caused by debris from the spall. In this type of testing very little metallurgical investigation is done on failed bearings. Emphasis is placed on test conditions and statistical analyses of endurance data. More basic work has been done relating micro-structural changes to fatigue performance. Dyer" and Wood, Cousland, and sargant9 have used mostly simple materials, such as single crystals and single-phase polycrystalline specimens, under simple alternating strain to identify a systematic process of fatigue damage. drutowski" was concerned primarily with the relationship between steel structure, contact stress, and energy losses in rolling contact. dones11 and Bush, Grube, and Robinson12 utilized changes in microstructure and residual stress in overload-tested rolling contact elements as a means of investigating the fatigue process. Work is being done on an ASME-sponsored contract,13 using both simple and complex materials, but there is still a long way to go before such theories as pore and void growth in simple structures can be applied to the relatively complex bearing steel microstructure. The purpose of this paper is to report on an investigation into the effect of steel cleanliness on the structural alteration and residual stress changes found in overload-tested ball bearings. Using these results and those of previous investigators, we will propose probable failure mechanisms in both overload- and normal load-tested ball bearings.14,15 PROCEDURE Ball bearings? 3208 size, were fabricated from SAE 52100 steel obtained by five different melting practices. The melting practices, chemistry, and inclusion ratings for the five lots of steel are summarized in Tables I and 11. The nonmetallic inclusion ratings were determined by the Jernkontoret method described in ASTM E45-51 Method A. This technique consists of microscopically examining a series of polished samples taken from specified locations in the ingots, billets, or bars. Each sample is surveyed at XlOO magnification and the inclusion types and sizes are compared to standard fields. Because of the nature of these ratings all values in Table I1 are rounded to the nearest half. The elec-

Jan 1, 1965

Jan 1, 1954

By A. R. Troiano, W. J. Barnett

IN recent years the demands of space limitations and increased loads, particularly in the aircraft industry, have accelerated the trend toward utilization of ultra-high strength steels. The increased application of such steels has focused attention on the phenomenon of delayed failure or static fatigue. Parts subjected to a static load, after successfully sustaining the load for an extended period of time, may fail in a brittle manner. Subsequent examination of such failed parts by conventional laboratory tests in many cases reveals no apparent signs of embrittle-ment. That is, the material exhibits good ductility and impact resistance. Furthermore, consideration of the service conditions (environment and temperature) under which this brittle failure occurred eliminates its classification as a stress-corrosion or creep type of failure. Recently this unique time dependent fracture process has been the subject of numerous investigations. The most significant result of these studies was the recognition of hydrogen as the source of embrittlement. While the effect of numerous variables on the occurrence of static fatigue failure has been defined, an adequate explanation of these behaviors is lacking. The occurrence of this phenomenon in steels generally has been limited to strength levels in excess of 180,000 lb per sq in. Although steels at high hardness levels have exhibited delayed failure in the absence of hydrogen introduction after heat treat-ment,'.' this behavior was most prevalent when the material in processing had been subjected to an environment conducive to the absorption of hydrogen. Delayed failures have been produced in high strength steels by the introduction of hydrogen

Jan 1, 1958

By G. L. Hassler, E. Bruner

An apparatus and method is described whereby the relation between saturation and capillary pressure under decreasing saturation can be quickly determined for small core samples. The initially saturated core is cen-trifuged at increasing rates and the average saturation is measured at each rate with the aid of a stroboscope device. A theory and calculation procedure is given whereby the accelerations and saturation values can be converted into a true curve of capillary pressure versus saturation. The present work differs from previously described use of the centrifuge to obtain capillary-pressure curves of core samples3 in that the core is centrifuged alone, so that the whole range of saturations required by the properties of the sample and the radially varying centrifugal force occurs within the sample. The calculation procedure nevertheless secures correct results from simply obtained values of the average saturation. The apparatus described was developed in connection with studies of capillary pressure and wetting of oil-field rocks, and the paper provides the apparatus background for a previous publication' dealing more fully with the uses and implications of the data in petroleum engineering. The method is applicable, however, to general combinations of immiscible fluids and porous or comminuted solids, and may be useful in other fields. Introduction The importance of capillary phenomena in determining the behavior of liquids in porous media has long been recognized. The concept of capillary Pressure was early formulated, and in recent Years discussions of the application of the laws of capillarity to oil field problems have appeared.l-3 One reason why progress in the application of capillary phenomena to the solution of problems of reservoir mechanics has not been more rapid has been the lack of a, satisfactory technique for measuring the capillary pressures in reservoir rocks. It is the principal purpose of this paper to describe a method by which the relation between capillary pressure and saturation can be determined for small consolidated core samples which have been extracted and resaturated, Capillary Diaphragm Perhaps the most direct way to measure the capillary pressure in a rock is to make piezometric contact with the wetting liquid through a diaphragm of porous material with high displacement pressure saturated with the liquid in question.3-6 The liquid in the diaphragm assumes the pressure of the liquid in the core, which can then be measured with a manometer, while the atmospheric air is prevented by capillarity from entering the diaphragm and affecting the pressure measurements as long as the displacement pressure of the diaphragm is not exceeded. With an apparatus of the type illustrated schematically in Fig. I, the relation between capillary pressure and saturation can be measured for a small core sample by starting with the core saturated 100 per cent, applyillg successively greater suctions

Jan 1, 1945

By R. F. Mehl, B. Lustman

THE formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.1 It is necessary here only to enumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type-i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained-the isothermal growth of the phase follows a simple parabolic equation: [1 = ki [I]] where X is the thickness of the alloy layer, k the reaction rate constant, and [t] the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.3 In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varies with temperature according to the Arrhenius equation: [k = Ae-QIRT [2]] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By G. E. Goodspeed

The Cornucopia gold quartz veins form a parallel vein system traversing meta-morphic and granodioritic rocks. Field and petrographic evidence suggests that inetasomatism has played an important role both in the emplacement of the grano-diorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage, and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore-forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a shght amount of cross faulting, and some movement along the planes of the veins as well as oxidation. Introduction Cornucopia is in the southeastern part of the rugged Wallowa Mountains of northeastern Oregon. It was founded over 50 years ago following the discovery of its system of gold quartz veins. The major veins are roughly parallel and dip into the western side of Pine Valley, which drains the southern slope of the range. Previous operations had cut the upper portion of four major veins with two tunnels over 1000 ft. apart, when the present operating company drove a third tunnel, called the Coulter, at the level of the valley over 1000 ft. lower to intersect the most easterly major vein at over 6200 ft. from the portal. General Geology of District The oldest rocks in the vicinity are metamorphosed sediments and volcanics. These, for the most part, are presumably Mesozoic in age, although some black argillites outcropping along East Pine Creek are considered to be Permian.l,2 These rocks have been deformed and metamorphosed in general to hornfels at the close of the Jurassic. The series was then invaded by a granodiorite batholith, the origin of which is

Jan 1, 1941

By G. E. Goodspeed

The Cornucopia gold quartz veins form a parallel vein system traversing meta-morphic and granodioritic rocks. Field and petrographic evidence suggests that inetasomatism has played an important role both in the emplacement of the grano-diorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage, and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore-forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a shght amount of cross faulting, and some movement along the planes of the veins as well as oxidation. Introduction Cornucopia is in the southeastern part of the rugged Wallowa Mountains of northeastern Oregon. It was founded over 50 years ago following the discovery of its system of gold quartz veins. The major veins are roughly parallel and dip into the western side of Pine Valley, which drains the southern slope of the range. Previous operations had cut the upper portion of four major veins with two tunnels over 1000 ft. apart, when the present operating company drove a third tunnel, called the Coulter, at the level of the valley over 1000 ft. lower to intersect the most easterly major vein at over 6200 ft. from the portal. General Geology of District The oldest rocks in the vicinity are metamorphosed sediments and volcanics. These, for the most part, are presumably Mesozoic in age, although some black argillites outcropping along East Pine Creek are considered to be Permian.l,2 These rocks have been deformed and metamorphosed in general to hornfels at the close of the Jurassic. The series was then invaded by a granodiorite batholith, the origin of which is

Jan 1, 1941

By T. lkeda, R. S. Montgomery. A. Hara

Actual test specimens used in the previous laboratory wear investigation,' were fully characterized and the data is given in Table 1. Most of the carbides tested could be placed into groups of similar mean grain size. When the wear rates of the members of these groups were plotted as functions of their hardnesses, a family of curves resulted; curves for groups containing data from larger grained composites were at lower wear rates at the same hardnesses. Most specimens tested showed only A-1 porosity (ASTM Standard designa-

Jan 1, 1971

Jan 1, 1949

By O. N. Carlson, H. A. Wilhelm, H. E. Lunt, J. M. Dickinson

On the basis of data obtained from microscopic examination, melting observations, cooling curves, X-ray analyses, and resistance measurements, phase diagrams have been proposed for the Th-Cb and Th-Ti alloy systems. Both are simple eutectic systems and have no terminal solid solubility or intermediate phases. The eutectic between thorium and columbium occurs at a composition of about 8 wt pct Cb and a temperature of 1435°C. The Th-Ti eutectic occurs at 1190°C at the composition 12 wt pct Ti. No change was observed in the transformation temperature of thorium in either system or in the titanium transformation. RECENT study of thorium and its alloys has been promoted because of the possibility of employing this metal in nuclear reactors. Their corrosion resistant properties, nuclear characteristics, and high melting points put columbium and titanium among the many metals being employed in the study of thorium alloys. Since a knowledge of the phase relationships would be important in the application of such an alloy, investigations were undertaken to propose phase diagrams for the Th-Cb and Th-Ti systems. Experimental Procedures Thorium metal sponge was specially prepared for use in this investigation. Carbon in a quantity less than 0.04 wt pct was the principal impurity. There was also less than 0.01 pct each of iron, calcium, zinc, aluminum, and nitrogen in the thorium. Columbium, both as a powder and sheet metal, was obtained from the Fansteel Metallurgical Corp. The manufacturer's specifications indicated that the metal contains less than 1 wt pct total impurities. An analysis of the metal showed approximately 0.18 pct C in the powder and less than 0.05 pct C in the sheet. The titanium used was commercial sponge, reported to be 99.5 pct Ti. An analysis showed that this metal contained 0.2 pct Fe. Preparation of Alloys—Since the metals used in this investigation are reactive and might become contaminated on melting in a refractory crucible, the alloys were prepared by arc melting. The titanium sponge was employed in the form of small lumps while the columbium additions were made either as pressed pellets of powder or as clippings from sheet. The alloying material and the thorium sponge were melted together under argon in conventional arc melting equipment employing a tungsten electrode and a water cooled copper crucible.

Jan 1, 1957

By Frederick M. Becket

SHORTLY after the Armistice there appeared a few references to numerous attempts that had been made to produce steel without the aid of manganese, or at least with manganese in abnormally low percentage. Some years later, during two consecutive days of train travel, I had excellent opportunity to read Sir Robert Hadfield's book, entitled "Metallurgy-Its Influence on Modern Progress," and also his paper, "The Metal Manganese and Its Properties : Also the Production of Ferro-Manganese and Its History," presented at the spring meeting of the Iron and Steel Institute, 1927. Both the book and the paper are most interesting historically to makers of alloy steels and

Jan 1, 1931

By Klaus Emicke

The paper describes the lead refining process operated at Norddeutsche Affinerie (N.A.). Incoming materials are different grades of lead with varying percentages of impurities: Cu, Te, As, Sn, Sb, Bi, precious metals. The facilities are designed for charge-wise operation. After drossing, generally Te, As, Sn and Sb are removed substantially by the Harris Refining Process using fused NaOH. A certain selectivity during refining is achieved by controlled addition of NaNO3. Another refining step is decopperizing by means of elemental sulfur. Complete separation of Te, As, Sn and Sb is accomplished by chemical methods in a leaching plant. A Howard Press is used in the Parkes Process for desilverizing. After vacuum dezinking in kettle, Bi is removed, if required, by means of Ca and Mg. In an end refining step Ca, Mg and Zn are removed by having the lead melt treated with NaOH and NaN03. The refined lead as such, or in the form of special alloys, is cast by an ingot casting machine into 50-kg ingots. Zinc which is used as a precipitant in the Parkes Process is recovered by distillation from the high grade Ag-Zn-Pb crystals in Faber du Faur retorts while the Pb/Ag alloy is fed to the cupellation furnace. Ca and Mg are removed from the Ca-Mg-Bi crystals formed in the course of Bi removal, and the Bi-bearing lead is cast into anodes. The electrolytic lead refining facilities at N.A. are operated largely for the purpose of separating Pb and Bi. These facilities are also used particularly for the refining of Bi-bearing lead which had gone through the above process, but from which Bi has not been removed by Ca and Mg.

Jan 1, 1970

By C. R. Boyd

WITHOUT attempting to do more than give a preliminary or skeleton report upon the geology and minerals of Southwestern Virginia at this time, I am led to hope that the great commercial importance of the sixty miles of cross-section here crudely treated of

Jan 1, 1877

By T. R. Lippard

PURE gypsum may be broken down into its constituents as follows: [ ] Standard specifications (ASTM Designation C22-25) state that a material shall not be considered gypsum if it contains less than 64.5 pct by weight of CaS042H2O. Anhydrite, the second calcium sulphate mineral found in nature, may be broken into its constituents as follows: [ ] PROPERTIES OF GYPSUM AND ANHYDRITE Pure gypsum is colorless to white but various impurities change its color to shades of gray, brown, red, or pink. It has a hardness of 2 in the Mohs scale and can be scratched with the fingernail. The specific gravity of pure gypsum is 2.3 to 2.4, so that rock gypsum, free from moisture, weighs about 145 lb per cu ft. Gypsum crystallizes in the monoclinic system in tabular crystals that exhibit good cleavage

Jan 1, 1949

By J. H. Reynolds

The possibility of using a semiconductor, metal, semiconductor structure as a light detector is discussed. A brief theoretical argument is presented which predicts that this structure should have pho-toresponse characteristics similur to those of a metal-semiconductor diode, but with the magnitude of the current increased by a transistor gain factor. Measurements made at low frequencies on a particulur S-M-S device agree u~th this prediction aizd shoul that significant gain factors are attainable. The current gain is substantially higher than that predicted for the metal base transistor. It is proposed that the operation of these units is more closely approxinzated by the metal-gate model which predicts higher current gains. A qualitative discussion of its high-frequency performance indicates that detection of light modulated at microwave frequencies by a S-M-S deuice is possible. ADVANCES in the technology of chemical vapor deposition'-4 have made it possible to form a S-M-S structure consisting of a thin metallic layer sandwiched between layers of single-crystal semiconductor. It has been proposed5-7 that, if the metal layer is made sufficiently thin, this structure could be used in an amplifier having several advantages over presently available transistors including higher-frequency performance. Calculations8 predict that the maximum gain-bandwidth product is nearly an order of magnitude higher than that of a bipolar transistor having the same geometry. Maximum oscillating frequencies in the microwave range are predicted. Electrical measurements made on S-M-S devices have shown that, although the theoretical frequency characteristics are not presently attainable, current and power gain is obtained. Another possible application of the S-M-S structure is its use in a light detector. This structure is a three-layer relative of the metal-semiconductor diode. Light detection using M-S diodes is the subject of considerable present interest. They are known to have a short response time and the ability to detect light having a photon energy below the semiconductor bandgap. In this paper, the mechanism by which S-M-S photocurrent is generated is discussed. An expression is derived which shows that the response characteristics are similar to those of a M-S diode, but that the magnitude of the current is increased due to the transistorlike behavior of the device. The results of low-frequency response measurements on a particular S-M-S structure are presented. These agree with the theoretical predictions and show that significant gain factors are attainable. A qualitative discussion of the high-frequency characteristics is presented which predicts that detection of light at microwave frequencies by a S-M-S device is possible. THEORY In this discussion, the photocurrent, iT, measured across terminals attached to the semiconductor emitter and collector layers is related to the current pho-toemitted from the metal base layer. The latter will be referred to as the primary photocurrent. The behavior of the primary photocurrent is determined by the characteristics of the two metal-semiconductor diodes. The diode photoemission is illustrated in Fig. 1, which shows the emitter and collector potential barriers. The metal thickness has been greatly exaggerated. As will be discussed later, the actual barrier shape can be much more complex, but this diagram illustrates the essential features of the photoemission process. An absorbed photon having an energy greater than the barrier height can emit an electron into the emitter or collector. Since this process is discussed

Jan 1, 1968

IN CIRCLES where mining men are wont to fraternize, a statement often heard is: "Yes, I spent six (or two, or ten, or thirty) years down at 'Chuqui.' " This means Chuquicamata, the site in Chile of what in all probability is the world's largest deposit of copper ore. One hears similar remarks regarding Braden and Andes, and, in fact, regarding a score of other big mines in South America, Africa, and elsewhere, but Chuqui seems to lead the others as the locale of engineers who have done a stint in foreign countries. One reason probably is that it is the Anaconda Company's premier foreign operation. Because of its unusual size and the diversity of its operations a great many men are needed. It is a sort of training school for young engineers; but, also, Anaconda has sent down a great many mature members of its big organization for special assignments like metallurgical research or plant construction. Chuquicamata is about 150 miles northeast of Antofagasta, at an elevation of 9,500 ft. It is in an almost rainless desert country where the wind (it is alleged by some) blows most of the time. However, the copper mining entrepreneurs have done their best to make up for what nature has neglected to do in creating a pleasant environment for the people who operate the mines. These include about 160 "foreigners" of whom 86 are from the United States, most of them accompanied by their families. There are 165 Chileans on the staff. Comforts, conveniences, and many luxuries are provided to offset in some measure the disagreeable features of the climate. Nevertheless, as I have implied, engineers at Chuqui generally jump at the chance to become "alumni" when opportunity offers. At the same time, they appear to take pride in their alma mater.

Jan 1, 1957