Search Documents

By C. E. Shoenfelt

Jan 1, 1942

By W. R. Hansen, F. W. Boulger

Twenty-nine laboratory steels were studied to determine the effects of composition and ferrite grain size on drop-weight and Charpy V-notch transition temperatures. The experimental steels covered the following ranges in composition.. 0.10 to 0.32 pct C, 0.30 to 1.31 pct Mn, 0.02 to 0.43 pct Si, md nil to 0.136 pct acid-soluble Al. Although most of the data were obtained on hot-rolled samples, some plates were heat-treated in order to cover a wider range in ferrite grain size. The experimental data were used for a multiple-correlation analysis conducted with the aid of an electronic computer. The study showed that carbon raises and that manganese, silicon, aluminum, and finer ferrite grains lower both drop-weight and Charpy transition temperatures. Quantitatively, variations in composition and grain size have a more marked effect on V15 Charpy transition temperatures than on the drop-weight transition temperature. Useful correlations were found between transition temperatures in drop-weight tests and those defined by seven different criteria for Charpy tests. Evidence was accumulated that the conditions ordinarily used for drop-weight tests are more severe for 1-1/4-in. -thick plate than for 5/8- to 1-in. -thickplate. PROJECT SR-151, to study quantitatively the effects of metallurgical variables on performance in the drop-weight test, was established by the Ship Structure Committee late in 1958 on recommendation of the National Academy of Sciences, National Research Council. This project was initiated as a result of the increasing use of the drop-weight (nil-ductility) test in predicting the ductile-to-brittle behavior of steel. Qualitative data indicated the drop-weight was not as sensitive to metallurgical variables as the Charpy V-notch test. Furthermore, the available information indicated that the drop-weight test did not show the superiority of killed steels over semikilled steels reflected by Charpy tests. This difference in sensitivity to brittle fracture is considered important because the drop-weight transition temperature has been reported1 to correlate better with service-temperature failures than the V-notch test does at a constant energy level. Therefore, this project was concerned with establishing quantitatively the effects of metallurgical variables in the drop-weight test. For comparison, Charpy V-notch data were obtained for the steels investigated. This paper summarizes the results of the investigation. Most of the steels used for the study were made and processed in the laboratory. However, some tests were also made on commercial killed steels available from Project SR-139 (SSC-141). During the course of the investigation, data were obtained on the effects of carbon, silicon, manganese, and aluminum on transition temperatures of drop-weight and Charpy specimens. In addition, the effects of heat treatment which changed the ferrite grain size and the transition temperatures were also investigated. Finally a few exploratory studies were made on commercial killed steels to evaluate the effects of plate thickness, grain size, and heat treatment on the performance of drop-weight specimens. EXPERIMENTAL PROCEDURES Preparation of Materials. A total of twenty-nine 500-lb induction-furnace heats were made and processed in the laboratory for the investigation. Carbon, manganese, silicon, and aluminum contents were systematically varied. Melting and rolling techniques proven satisfactory in a previous project2 were used as a guide for the current investigation. Composition. The composition of the twenty-nine laboratory heats made for this project are given in Table I. The steels are divided into three groups. The first group consists of ten aluminum-killed steels similar in composition to Class C ship-plate steel. The second group consists of ten semikilled or Class B type steels. In both of these groups the carbon and manganese contents were intentionally varied over a wide range. This wide range in composition was helpful in obtaining quantitative data from a limited number of steels. The primary purposes of these two groups of steels was to determine the effects of carbon, manganese, and deoxidation practice. In addition, one steel in each group (Steels 2-2 and 9-2) were made about 1 year after the start of the program in order to check consistency of melting practice. The third group of nine steels listed in Table I was intended for studies on the effects of silicon and aluminum. In eight of these steels carbon and manganese were held relatively constant at levels of about 0.2 and 0.8 pct, respectively, while silicon and

Jan 1, 1963

By James W. Baxter

Underground mining of limestone is becoming increasingly practicable in Illinois. Most quarries are near rivers on the western and southern borders where competition for land use is intensive. Increasing demands for stone can be met by expanded mining with access by adits in existing quarries and by inclines and shafts at downdip sites. Geologic, hydrologic, and engineering conditions indicate that deep mines in the Ste. Genevieve, Salem, Ullin, and basal Burlington limestones of Mississippian age and in the Moredock member of the Dunleith formation of Ordovician age are particularly feasible, but development will require prudent exploration and planning to ensure that the product will be of good quality.

Jan 1, 1981

University of Alabama University, Alabama Mining and Metallurgical Society WILLIAM S. SPRINGER, President ROBERT E. MEAD, Secretary J. R. CUDWORTH, Faculty Sponsor MILTON H. FIES, Counselor University of Arizona Tucson, Arizona Miners' Society PERCY E. COE, President W. JAMES THOMAS, Secretary E. P. MATHEWSON, Faculty Sponsor B. R. HATCHER, Counselor

Jan 1, 1937

VARYING in thickness and in number from place to place, coal seams in the Canadian Rockies also range in pitch from nearly horizontal to vertical, sometimes with overturns. Over the entire coal-bearing area there are considerable differences of rank in coals of the same geological age, and there are marked differences in ash content and washability characteristics. Correlation of seams at mining operations within a few miles of each other has often proved impossible. These factors influence mining methods, and, of course, production results. The oldest coal formations of western Canada are of Lower Cretaceous age, as the carboniferous sediments are marine and contain no coal. Coal is also present in formations of Upper Cretaceous and Tertiary ages. The rank of coal varies from semianthracite in some operations in the Kootenay and Luscar formations of the Lower Cretaceous in the Rockies to lignite in the Tertiary fields of the Saskatchewan prairies. Fig. 1 shows the general extent of the formations.

Jan 8, 1954

By S. K. Nicol, A. R. Swanson, J. C. Day

Addition of oil to a suspension of hydrophobic coal particles can influence its dewatering characteristics. An agglomeration process occurs in which coal particles are held together by negative capillary pressure at particle/oil/water contacts. Consequently, the units round which flow can occur are enlarged and this improves dewatering parameters such as drainage rate, solids recovery, and equilibrium moisture content. This paper discusses processes which attempt to use this principle, in terms of metallurgical and economic efficiency. The discussion is augmented by results of recent experiments on the effect of oil addition to centrifuges and vacuum filters.

Jan 1, 1980

Executive DEGOLYER, Chairman SIDNEY H BALL RICHARD PETERS, JR WILLIAM H BASSETT J V W REYNDERS Finance GEORGE D BARRON, Chairman H A GUESS GEORGE OTIS SMITH Membership J M CALLOW, Chiarman FRANK L ESTEP WILBER JUDSON GEORGE D BARRON H N SPICER Alternates P A MOSMAN EDWARD B STURGIS

Jan 1, 1923

By Louis A. Panek

Ground movements in the zone adjoining an active cave were measured at four sites in the San Manuel Mine. Measurements were made to detect extension and inclination, basic components of displacement, which can readily be duplicated by mine personnel using relatively simple equipment. The displacements demonstrated the development of a zone of strain relief surrounding the active cave, within which the ground tends to migrate toward the cave, and extension cracks develop tangential to the cave. This expansion of the ground surrounding an active cave can be exploited to promote future caving; it also creates special problems with respect to the design of an effective ground support system for mine openings in the production area.

Jan 1, 1981

By Richard E. Goodman

Rock slope stability assumes different roles in decision making as a mining venture develops and, accordingly, geological investigations vary in thought and in deed according to the project stage. During exploration, stability questions bear on the decision whether or not to mine, because their resolution affects the cost of mining. During the mine lay-out stage, stability is a key factor in deciding how to mine. Finally, during mine operation, stability affects safety and operating costs, and therefore, pit productivity. Among the many considerations influencing stability, rock mass classification and geological environmental factors count heavily. The rock mass behavioral class depends upon the rock character and its degree of fracturation. The loads on the rock are derived from the environmental factors of initial state of stress and the water regime. Of course, stability is also tied to a host of non-geological factors such as the pit geometry, mining style, relative wealth, philosophy of mine operation, and accident history. METHODS OF STABILITY EVALUATION AND CORRESPONDING INVESTIGATORY TOOLS The purposes of the geological investigation are to identify and evaluate the geological factors influencing stability so that the vital questions can be analyzed. The tools selected for stability analysis reflect the stage of development of the mining scheme and therefore the geological investigations, which must furnish data for the analyses and must vary with the project stage. For exploration and mine planning, the methods of resolving stability questions must meet the need to evaluate numerous parameters in limited time; examples of such methods are stereographic projections (1, 2, 3) charted solutions(4) and simple physical models (5, 6). An investigation program that employs geological mapping tools and aids to mapping, such as geophysics, with relatively few rock tests, is in balance with these analytical methods. First data about the water regime are obtained from observed piezometric levels, and the initial state of stress is queried simply through geological inference and experience. In the layout stage more elaborate physical scale models (7) and perhaps finite element models (8, 9, 10, 11, 12), will be relevant to the design process and therefore much more detailed geological investigation is required. The scale of observation of both rock material and joints will be significantly enlarged and mechanical tests of rock and joint strength

Jan 1, 1972

E. T. DUMBLE, Houston, Tex.-This paper is a continuation of one that was published by Mr. Garfias, I believe, in the Journal of Geology, 1912, in which he gave the results of his investigations in Mexico, showing that the basalt extrusions frequently did not come up as cones. but reached the surface as a small neck and then mushroomed out into a sill, penetrating the beds both in limestones and in shales. He has continued his investigations to show that as these basalt protrusions came up they forced the strata into a funnel shape at the top instead of throwing them out altogether. While this may be true concerning these particular beds, there are other places at which the basalt does appear clearly as cones and dories, and there the funnel structure does not exist. We know that the sills are there, because we find them in the wells. In one well that I know of. we found a 2-ft. sill of basalt at about 1600 ft. and oil below it at about 2100 ft.; others have gone through similar beds. We also know that there. are cones, because north of the Ranuco River one well struck basalt at about 800 ft. and continued in it for several hundred feet-did not pass through it at all. This paper of Mr. Garfias will give us considerable help in that oil field. W. E. WRATHER, Wichita Falls, Tex.-I would like to ask for information as to the temperatures of Mexican oils. I have heard a number of conflicting reports about the high temperatures of the water and oil, and the relationship between them.

Jan 1, 1918

By P. Somasundaran

An experimental and theoretical treatment of the depressing effect of inorganic electrolytes on the amine flotation of quartz is presented. Experimental data obtained for the amine flotation of quartz as a function of pH with potassium nitrate as depressant was used to test the models for the effectiveness of inorganic ions as depressants. The validity of commonly used assumptions are examined. The surface tension data obtained for dodecylammonium acetate solutions as a function of KNO3, concentration indicated that the collector adsorption on bubble cannot be neglected in the treatments, since this adsorption changes significantly with the addition of the inorganic electrolyte. It also indicated the possibility of significant changes in the specific adsorption potential of the collector occurring with the addition of inorganic electrolytes.

Jan 1, 1975

By Lee Morris, Charles E. Lawall

This paper represents the results of a study to determine the source, mode of occurrence and conditions influencing the flow and liberation of large volumes of inflammable gas in the Pocahontas No. 4 coal bed in southern West Virginia. A study of this kind is of interest in connection with mine ventilation, because in the removal of gases from coal mines it is very important to know the origin, the occurrence and laws of gas flow. The study was started in April, 1931, and the data and observations were obtained throughout a period of 15 months of field work. Geology The country where this study was made is mountainous and rugged; great cliffs, precipitous slopes and deep narrow gorges are found throughout the area. The outcropping rocks consist of stratified layers of sandstone, shale, limestone and deposits of coal of Carboniferous age. The Pottsville series of the Pennsylvanian, lying at the base of this period, cover the greater portion of the area. A stratigraphic section of the Pocahontas group of the Pottsville series is shown in Fig. 3. The older rocks outcrop in the extreme southeastern part of the area, but are under drainage in the central and northern parts due to the gradual northwest dip of the strata. The structure has a general northeast-southwest trend (Fig. 1). North of Dry Fork anticline the strata have been only slightly disturbed by movements of the earth's crust; it is now a long monocline. Southeast1 of Dry Fork anticline the strata are warped into great arches and deep troughs and are broken by overthrust faults. All of this folding is probably the result of the intense folding associated with the formation of the Appalachian Mountains. Pocahontas No. 4 Coal Bed The Pocahontas No. 4 bed, lying approximately 550 ft. above the base of the Pottsville series, is one of the thickest and most gassy coal beds in

Jan 1, 1934

By J. N. Hobstetter, J. J. Becker

Deformed copper single crystals exhibited, upon annealing, a recrystallized twinned grain with a twin plane parallel to an active deformation plane, rotated approximately 22" about its pole, or else did not recrystallize at all. If extraneous deformation was not carefully removed, no simple orientation relationship was found. RECRYSTALLIZATION textures have been a subject of practical interest for many years, but any real understanding of their formation will have to start with a study of the recrystallization of carefully deformed single crystals. Some efforts have been made in this direction,'-' but much more experimental information is needed before a satisfactory picture of the crystallography of recrystallization can be formed. This paper reports a few results in copper single crystals. The crystals studied in this investigation were grown by the Bridgman method," and their orientations determined by the back-reflection Laue technique." Some specimens were simply deformed in compression, others were sheared, and still others tested in a rotating-grip device, in attempts to remove end constraints. The details of their deformation behavior are described elsewhere.' The deformed specimens were annealed and the orientations of the recrystallized grains were determined optically, as described by Barrett and Levenson.8 Compressed Specimens Specimen 17-A, whose orientation is given in Fig. 1, was compressed to a total of 19 pct. As observed before,' increasing deformation took place by increasing density of slip lines in initially formed clusters, with little if any formation of new slip clusters in unslipped areas. The specimen was then etched in nitric acid until its length had been reduced from 0.766 to 0.735 in. It was annealed at 1000°C, in increments of a few minutes. After 63 min, two small grains had appeared in the center, Fig. 2. They were found to be twinned with respect to each other (AB, Fig. 4). After 30 min more, the specimen was completely recrystallized. A typical view of it is given in Fig. 3. A summary of all orientations found is given in Fig. 4, in which the prominent grain G is in (001) standard projection, and the poles of the active slip planes after deformation are indicated by SP (primary slip plane), CrSP (cross-slip plane), and CnSP (conjugate slip plane). All the orientations found were related through seven orders of twinning. A "family tree" of these twins is given in Fig. 5. Furthermore, the BG twin composition plane lies close to the cross-slip plane

Jan 1, 1954

By H. N. Thomson

GENERAL. THE Tooele plant of the International Smelting & Refining Co. is situated at the mouth of Pine canyon, Tooele county, Utah. It is connected with the main line of the San Pedro, Los Angeles & Salt Lake railroad by the Tooele Valley railway, and is about 7 miles from Tooele Junction. Fig. 1 is a general view of the plant. FIG. 1.-TOOELE PLANT OF THE INTERNATIONAL SMELTING & REFINING Co. The copper plant has been in operation since July, 1910, and the first blast furnace at the lead plant was blown in on Feb. 29, 1912. The location of the plant was selected on sloping ground with the idea of using gravity to the fullest extent and thus keeping labor at a minimum. Practically the entire plant is constructed of steel, reinforced concrete, and brick. Bingham ores, both lead and copper, are received over the Utah Consolidated Aerial Tramway. The tram buckets, each containing

Jan 7, 1913

By T. E. Schwarz

The publication of the report by Mr. F. L. Ransome1 was welcomed by many engineers who had mined in the heart of the San Juan country, braved its long and snowy winters, climbed its lofty peaks, run the gauntlet of its snow-slides, and studied its problems of geology, while making dividends for their English or American clients. This report helps one to understand why the bonanzas occurred, and why the inevitable " borrasca " presents itself where least expected. The Red Mountain district of Ouray county, a very productive section from 1884 to 1893, occupies considerable space in the report mentioned. The character of the ore-occurrence.

Jan 1, 1906

By R. M. Hudson

The removal of nitrogen from a nitrogenized low-carbon sheet steel that contained 0.011 wt pct N was determined during heat treatment in Hz-N, mixtures. TIze process followed a first-order rate law; that is, plots of the logarithm of nitrogen content in steel were linear with the time of treatment at a given temperature. The rate of removal increased with an increase in temperature from 900" to 1300°F. By 1400°F the rate in dry hydrogen had decreased to a value intermediate between the rates at 1200" and at 1300°F; in wet (2.47 vol pct water vapor) hydrogen the rate at 1400°F was less than the rate at 1300°F and nearly the same as the rate at 1200OF. The rate at a given temperature increased as the 3/2 power of hydrogen concentration in the atmosphere. While wet atmosplzeres were generally more effective than the corresponding dry atmosplzeres, the effect of water vapor was much less pronounced than the influence of hydrogen content. NITROGEN is the principal agent in the strain aging of ferrite, the effect of carbon being secondary.' To eliminate the return of the yield point after straining and aging, it is claimed2 that the amount of nitrogen in solution in steel must be reduced to 0.0002 wt pct. Strong nitride-forming elements (titanium, vanadium, zirconium, and aluminum) can act to eliminate strain aging by combining with nitrogen. It is extremely difficult to decrease the nitrogen content in commercial steels to the low level required by conventional coil annealing because of the poor contact between the strip surface and the reactive atmosphere. However, a variety of gas-metal reactions can be effected by use of the open-coil annealing method,3 in which the metal surface is fully exposed to the atmosphere. With this possibility in mind, the Applied Research Laboratory has studied the influence of time, temperature, and atmosphere composition on the removal of nitrogen from low-carbon sheet steel. MATERIALS AND EXPERIMENTAL WORK Samples from a commercial nitrogenized low-carbon steel (0.010 in. thick) in the cold-reduced condition were used. The chemical composition of this steel is given in Table I. The gas mixtures used are listed in Table 11. The moisture content in the "wet" annealing atmospheres was controlled at a +70°F dew point (2.47 vol pct water vapor) by passing the gas mixture through a glass tube packed with a solid mixture of 10 pct anhydrous oxalic acid and 90 pct oxalic acid dihydrate held at 127°F; this technique has been described previously.4 For "dry" atmospheres, the gas mixtures were passed through a cold trap immersed in liquid nitrogen. A hinged-top Hevi-Duty electric furnace was used with a Vycor-glass furnace tube. When the furnace was at the desired temperature, the gas mixture was passed through the furnace at a flow rate between 1.1 and 1.2 cfh; coupons (size 3 by 3/4 in.) of the steel were pulled into the center of the Vycor-glass

Jan 1, 1964

By Hannon, J. W. G.

Silicosis is today's most important industrial disease and probably dates back to the Stone Age. Since the industrial revolution, increasing attention has been paid to those occupations where mineral dust is present in the air breathed by the workers. For many years it was assumed that the inhalation of all mineral dusts was hazardous. but investigations conducted in several countries pointed the statistical finger of guilt at free silica in any of its numerous physical forms as a dust of outstanding toxicity. Recognition of silica as the chief hazard has resulted in widespread use of the term "silicosis." Depending upon the concentration of finely divided silica dust to which the individual is exposed and the duration of exposure, silicosis may become a disabling condition in from one to thirty years. The structure of the lung and respiratory passages is such that only minute particles of silica can gain entry to the air cells in the lung (5 microns or under are most toxic). When these minute particles gain entry to the lung tissues they stimulate certain protective cells in the lung to multiply at an excessive rate. The cell's undergo inflammatory changes which result in nodular scars and a low-grade inflammation of the lung tissue. These progressive changes in the lung structure gradually encroach

Jan 1, 1949

By Guillermo Zuloaga

THE iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana High-lands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Profes-sor Lindgren and Professor Newhouse.

Jan 1, 1933

By W. D. Robertson, A. S. Tetelman

The technique of decorating dislocations was employed to investigate deformation and fracture resulting from Precipitation of hydrogen in Fe-3 pet Si single crystals. It is shown that cracks are produced on (100) planes inside crystals, as a consequence of the precipitation of hydrogen gas, either when crystals are quenched from a hydrogen atmosphere at elevated temperatures or cathodically charged with hydrogen at room temperature. Plastic deformation in the vicinity of cracks, observed as arrays of decorated dislocations, is in conformity with the calculated stress distribution about a crack containing an internal pressure, and the observations provide information permitting a detailed analysis of the mechanics of crack growth. The fracture characteristics of crystals containing internal cracks were evaluated at 25o and -196°C and the results are related to the mechanism of hydrogen embrittlement in terms of the growth of preexisting cracks. HYDROGEN in bee iron or steel produces two characteristic changes in mechanical properties: I), a decrease in ductility (macroscopic strain at fracture) that depends on temperature and strain rate, and 2), spontaneous fracture under static load that depends on time and apparent stress. Resolution of these phenomena into the microscopic processes that combine to produce the macroscopic effects is especially difficult in the Fe-H system in which the active component cannot be directly observed and only maintained in equilibrium with great difficulty in the temperature and pressure range in which embrittlement phenomena appear. As a result of these complications, verification of the numerous hypotheses'-5 that have been proposed to explain the microscopic mechanism of embrittlement depends on self-consistency with measured changes in macroscopic properties that are averaged over the volume of a specimen. It is obviously important to obtain a more direct evaluation of the microscopic processes that combine to produce embrittlement. Accordingly, the present investigation was designed to identify and observe, as directly as possible, the microscopic effects of introducting hydrogen into a bee crystal. It was concluded from a previous investigation6 of X-ray line broadening, produced by introducing hydrogen into pure iron at room temperature, that the only effect that could be associated with the introduction of hydrogen was plastic deformation; in particular, dilation of the lattice was not observed, within ± 0.01 pet, and no evidence was found that could be interpreted to support the idea7'* that hydrogen occupies tetrahedral interstitial sites in the iron lattice. The absence of lattice dilation is consistent with the extremely small solubility of hydrogen in bee iron9,10 (0.015 at. pet at 900oC and 1 atm pressure), and the evidence of plastic deformation is consistent with the fact that hydrogen, introduced by cathodic charging, eliminates the carbon yield point.11-13 Following this investigation, the immediate problem was to devise a method by which plastic deformation could be observed directly. The technique employed by Hibbard and Dunn14 to observe the movement of dislocations during bending and subsequent polygonization of Fe-3 pet Si single crystals was adopted and modified for the present purpose to include the observation of dislocation arrays in the volume of the crystal, and their association with the fracture process. EXPERIMENTAL PROCEDURE Single crystals of a high purity Fe-3 pet Si alloy, containing 0.007 pet C, were grown in vacuum by

Jan 1, 1962

By C. R. Austin

THE paper describes an investigation on the pressure welding of low-carbon steels. The work necessitated a reproducible mechanical means of making the weld and also a test that would indicate the nature and completeness of the union. An apparatus including a high-temperature furnace was devised for making the welds, and the ordinary tensile pulling test 'in correlation with macroscopic and microscopic observations was used as a means of examining the result. Initially it was intended to devise some simple test of weldability, but as the experimental work progressed, it soon became clear that with our limited knowledge of the exact nature of the mechanism of pressure welding it was impossible to interpret our results or to devise a simple test of weldability. Hence it was manifestly necessary first to study the mechanism of such welding and attempt to elucidate the fundamentals underlying the so-called welding of steel by pressing together two metal surfaces. It also became evident that it was necessary to define the term "welding." In many early experiments when, two heated rods were pressed together and then pulled in the cold, very high tensile values were obtained, and yet the fracture took place exactly in the line of junction except for a few small scattered areas. In other words, the' rods pulled apart just as they were before being "stuck" together and had certainly not welded completely, despite the high value indicating the strong cohesive force operating. In this paper, welding has been considered as a form of intimate contact between two metal surfaces, so that the units lose their individual identity and there is no change in physical properties in passing through the weld from one unit to the other. This is defined as "true welding." When true welding has taken place completely over the whole section, the probability is that the rupture in tensile test will occur outside the weld.

Jan 1, 1932