Search Documents

By E. O. Karenna, A. D. Smigelskas

This is the third paper in a series on the diffusion of zinc in alpha brass.' At the time of the first paper it was accepted that diffusion in a substitutional type of solid solution depended upon an equal interchange of solute and solvent atoms across the diffusion interface (or past a given lattice reference point). Discrepancies in the size of the areas under the diffusion curves on each side of the interface, if observed, were explained on some other basis than the fact that the solute atoms might cross the diffusion interface without an equal number of solvent atoms diffusing across the interface in the opposite direction. The second paper presented evidence indicating that zinc atoms in alpha brass diffuse across the interface more rapidly in one direction than the copper atoms diffuse across the interface in the opposite direction. This phenomenon forced the interface to move in the opposite direction of the diffusion of zinc atoms to provide space for the additional zinc atoms dissolved in the alpha brass. That the interface and columnar grain structure on one side would remain intact during this mass movement was not expected; how ever, it is gratifying that they did. While the evidence was sufficiently satisfying to the author, it was decided that additional experiments were in order to prove that zinc diffuses more rapidly than copper in alpha brass. It is the purpose of this paper to present the results of these experiments. Procedure A bar of 70-30 wrought brass was selected, to avoid the relatively large volume change in going from beta to alpha brass as in the previous investigation. A bar 7 in. (18-cm.)* long and about 3/4 in. (1.9 cm.) wide was surface ground and polished with abrasive paper on plate glass to 0.4184 0.0002 in. (1.062j + 0.0005 cm.) thick. Six0.00j-in. (0.013-cm.) diameter molybdenum wires, chosen because of their very low solubility in coppcr and alpha brass, were strctched lengthwise along each of the two plane surfaces. Glass tubes placed at right angles to the wires every 1/2 in. held the wires tightly against the brass. The sample was then emersed in an acid copper sulphate plating bath and electroplated to a depth of about 0.020 in. (0.050 cm.) copper on all sides. The glass tubes were no longer necessary to hold the molybdenum wires in place and were removed. The sample was then electroplated to a depth of

Jan 1, 1947

By Edwin T. Myskowski, Alfred H. Hesse

THE development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly i00 per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson's X-ray data indicate that this decomposi¬tion is accompanied by a change in volume of as much as S per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson3 found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potters have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to g0 per cent Mn. is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparation of Alloys.-The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 Cu-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced go per cent when forged to ½ in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.-The tensile specimens, 0.313-in. diameter (1.25-in. gauge length), which were enclosed in evacuated Pyrex

Jan 1, 1942

By N. J. Grant, C. Stein

A more complete determination of the chromium-rich portion of the Cr-Ni phase diagram was made, based in part on resistivity measurements. The existence of a eutectoid reaction at 1215°C,made,based in addition to the previously reported eutectic reaction at 1343°C, was confirmed. Metallographic studies, lineal analysis, and diffusion-couple evidence were utilized to support Metallographicand extend the findings of the resistivity measurements. Delineation of the a chromium solvus line shows that the maximum solubility of nickel in a chromium decreases rapidly from 25 wt pct Ni at the eutectoid temperature to 16 wt pct. Ni at 950°C. IN recent years alloys of high chromium and nickel content have become of more interest as better performance of metals at higher temperatures is sought. It has become increasingly important, therefore, that the Cr-Ni binary diagram, which is composed of two of the elements commonly found in many high temperature alloys, be known more accurately. In particular, the chromium-rich portion of this diagram has for a long time remained incompletely determined and has been reported in the literature with a great deal of conflicting evidence. In general, electrolytic chromium of nominal purity was used by most of the earlier workers, who, except for Jenkins et al., made no further attempt to purify the metal. In the present redetermination of the chromium-rich portion of the Cr-Ni phase diagram, every effort was made to use the purest component metals available and to retain this purity throughout the preparation of the alloys and their subsequent handling. Early work by Voss, Bain," and Phebus and Blake4 indicated that the Ni-Cr binary diagram was a simple eutectic system with rather extensive terminal solid solutions. Later, Nishigori and Hamasumi," Tasaki, Weaver and Jellinghaus,' Matsunaga, and Jette, Nordstrom, Queneau, and Foote attempted to determine the limits of the phase fields. Except for Jette and coworkers, the other investigators agreed that the temperature of the eutectic reaction occurred between 1320" and 1340°C and at a composition of 50 or 51 pct Cr. There was, however, considerable disagreement as to the melting point of the chromium-rich alloys and the limits of the solid-solution fields. As a result of the studies of Jenkins et al., the liquidus and solidus curves up to 80 and 90 pct Cr, respectively, were outlined. In addition, the solid-solution phase fields at higher temperatures had been investigated and showed only two phases. The boundary of the chromium-rich a phase was not determined precisely according to these authors, but indications were that it tended to confirm the earlier work of Nishigori and Hamasumi. A more recent investigation by Taylor and Floyd,'" using X-ray methods, essentially corroborated the diagrams proposed by Jenkins et al., and by Wise and Eash (see Fig. 1). Again, no indication of a third phase in the chromium-rich portion of the diagram appeared. The earlier observations, however, are not substantiated by the modifications to the Ni-Cr binary diagram proposed by Bloom and Grant." In the investigation carried out by Bloom and Grant, X-ray methods showed that an eutectoid reaction existed at approximately 1180°C, in addition to the eutectic reaction at 1343°C (see Fig. 1). Their determination of the melting point of pure chromium was 1930°C (later revised to 1903"C)." Experimental Procedure and Results The chromium used for this study was electrolytic chromium, made available by the United States

Jan 1, 1956

By T. E. Leontis, J. P. Murphy

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By J. P. Murphy, T. E. Leontis

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By Robert Mehl

METALLURGISTS are properly interested in papers dealing with subjects ranging from the theories of the metallic state to very practical details on the use of metals. A review of theoretical metallurgy naturally excludes papers concerned with the usefulness of metals and limits itself to those concerned purely with the science of metals. Even in this more limited field the reviewer is confronted with thousands of papers dealing with facts and theories of metallic behavior, from which he can select only a few hundred. The selection is necessarily highly arbitrary. Certain classes of papers definitely fall within the scope of this review. Thus, papers on the deformation of metals, on the structure of alloys, on recrystallization, to select only a few, are fully represented. Other subjects, which verge on what is generally accepted as the science of metals, such as the magnetic properties of metals, the less familiar electrical properties and theories, adsorption of gases by metal surfaces, and the like, are treated scantily. Particular attention is given to reviews of subjects that fall with in the groups chosen; in a summary such as this, which is largely in the nature of a progress report, capably written reviews are of importance, particularly since the monograph and text book literature is so meager in this field.

Jan 1, 1935

By J. M. Karpinski, R. O. Tervo

A method and equipment have been developed for measuring the impact strength of grains of brittle materials. It is shown that brittle materials develop a characteristic particle size distribution when fractured by impact. A simple mathematical model has been found to describe this distribution, and one of the parameters of the model has been designated the r value. The r value is directly proportional to impact energy and, for fixed impact energy, it becomes a useful criterion of grain strength. Data are presented on the variation of the r value as a function of sample history, initial size, energy input and number of impacts. The results are interpreted in terms of the flaw theory of brittle fracture. The view is now widely held that brittle materials comprise a strong matrix, throughout which flaws or points of weakness are scattered at random. Failure always starts at one or more of these imperfections, and planes of fracture are established by the geometry of the flaw distribution. This view has been developed extensively by Weibull 1,2 and experiments of a confirmatory nature have been reported.3,4 Thus the process of fracture or size reduction of brittle materials can be regarded as a process of elimination or creation of flaws, and the concept of strength is intimately connected with the size and history of the specimen tested. One consequence of the point of view described above is that brittle materials will fracture to yield similar size distributions, although the impact energy to produce a given amount of fracture may vary greatly from one material to another. Generally speaking, experimental investigations of brittle fracture in solids have been confined to two extreme experimental situations. On one hand, we have tests on single specimens of well-defined, but artificial, geometry and, on the other, empirical data have been obtained on the feed-product relation in a variety of mills. The first situation necessitates specimen preparation, which in the case of brittle materials is equivalent to a priori size reduction, while the second one suffers from the disadvantage that little knowledge is gained about individual fracture events. Also, the statistical significance of single specimen tests may be questioned. Our approach lies somewhere between these two extremes. We test a large population of sized specimens and yet subject each specimen to a single fracture event. In 1956 G.H. Fetterley of Norton Co., Chippawa, Ont., made the empirical observation that product size distributions obtained from impacting sized grits can be described by the following equation where R is the proportion by weight of the grain that remains on a screen having an opening x on a side, x, is a parameter having the dimensions of length, and r is a number. This equation has since been derived on a theoretical basis by Gaudin and Meloy.5 They identify x, with the initial size of the test piece and r with the number of flaws per unit length. As will be shown below, our experiments indicate that both x, and r are functions of energy and hence they should more properly be called the effective initial size and the effective number of flaws respectively. Also, our empirical data give us no basis for assuming that r represents the effective number of flaws per unit length, rather than per unit volume. METHOD AND MATERIALS The impact test machine has been designed to feed specimens, essentially one at a time, into an evacuated chamber, where they fall freely and are struck with random orientation by one or the other of a pair of flat steel vanes. The vanes are mounted at opposite ends of a steel bar, which rotates at a closely controlled angular velocity about a vertical axis. Fig. 1 shows the flat circular vacuum chamber with the cover removed, and the horizontal steel bar with the steel vanes at the ends. The cylindrical pot in which the grains are collected after impact appears at the left. Fig. 2 shows the equipment assembled for a test. The vacuum chamber occupies the central position with the variable speed drive below the table surface, the vacuum pump at the extreme left

Jan 1, 1964

By J. W. Leonard

One of the more obvious phenomena which relate to coke formation is that soft coals of low volatile matter content tend to yield hard or high strength cokes while hard coals of high volatile matter content tend to yield soft or low strength cokes. This observation led researchers of the Coal Research Bureau of West Virginia Univ. to study the possibility of using Hardgrove grindability as a supplemental rank indicator for coking properties. Grindability has been used for many years as a means to measure the resistance of coal to comminution but it has rarely if ever been considered for evaluating coals for carbonization. The coal proper- ties which are measured by grindability are complex, but recent work with the difficult-to-correlate high volatile coals has demonstrated that a 93% correlation exists between grindability and the total petrographic rnicrinites, exinites, and resinites. This work demonstrated that inherent ash had no apparent effect on the grindability of high volatile coals, suggesting that the coal substance is apparently harder than the associated ash. These observations, together with the patented Burstlein process," indicate that the distribution of hard and soft components in the individual high volatile coals and blends of coals may be quantitatively interrelated to coke stability through selected ranges of coal volatile matter. The objective of this progress report is 1) to demonstrate the statistical relationships which exist between coal grindability and the numerous coal petrographic entities and 2) to present the results of initial studies concerning the correlation of the coke physical strength index of stability with coal volatile matter and grindability.

Jan 3, 1964

By E. E. Carpenter

(San Francisco Meeting, September, 1915) BELIEVING that the results accomplished in the mill of the Churchill Milling Co., Wonder, Nev., during the fiscal year ended Sept. 30, 1914, will be of interest, I am presenting the more prominent facts and figures showing the progress made in treating this ore with especial reference to tonnage, supplies, costs, and extractions. The mill is situated at Wonder, Nev., in the Wonder mining district, 55 miles east from Fallon, Nev., the nearest railroad point. All supplies are hauled this distance by freight teams, this method of transportation having been found more reliable for continuous service than trucks, the price paid for hauling being slightly under one cent per pound. In this mill are treated the ores of the Nevada Wonder Mining Co. ,

Jan 6, 1915

By Clark A. Sumner

An apparatus for agglomerating fine particles was developed in 1969 as a joint effort of Stauffer Chemical and O’Brien Industrial Equipment. Commercial sized units were built for agglomerating home dishwashing detergents. Recently, as a result of further pilot development, variation of bed depth and cage configuration has resulted in a means of controlling the amount of internal classification from a minimum, producing small agglomerates, to a maximum, producing compact rounded agglomerates. Little or no external classification of discharged agglomerates is needed. At maximum internal classification the agglomerates roll on a bed of fine particles rather than the shell resulting in increased agglomerate size.

Jan 1, 1977

By George L. Heath

It may at first appear doubtful that any further ideas can now come from such a well-trodden soil, when we consider that the ground of the subject has been so thoroughly gone over in many of its phases and that observations have been recorded in technical journals, ever since the days when Luckow and his cotemporaries brought the electrolytic deposition of pure copper to the position of an exact scientific method. Certain facts, however, which seem worthy of note, have come under the writer's observation during an extended use of the method in a large refinery, involving frequent tests of refined Lake and electrolytic copper, and thousands of assays of native copper concentrates and tailings. This work has required a careful study of the conditions suited to the assay of refined copper, and of ores and tailings— conditions which must be varied for each particular case to secure the best results. Especially is this true when we come to the exact determination of pure copper in the high-grade refined metal of the present day. Very slight traces of impurities (especially tellurium, selenium, bismuth, tin, arsenic and antimony) seriously injure the properties of copper, notably its electrical conductivity. The increasing demands of electrical science and construction lead to the conclusion that the analysis of all high-grade American coppers, at least, has become, and must be in future (in or-

Jan 1, 1898

By James W. Neill

Bituminous coal has for many years been used for the smelting of iron-ores in the blast-furnace. In some districts in Scotland it is used alone, in others it is used mixed with coke. The similar use of certain bituminous coals in the United States has been repeatedly mentioned in the Transactions. (See, for instance, as to the Hocking Valley coal, the papers of Dr. T. Sterry Hunt, Trans., ii., 275, and vii., 313; and as to Indiana "block-coal," the paper of Mr. J. S. Alexander, Trans., i., 225.) Phillips (Elements of Metallurgy, p. 250) says: " Raw coal for blast-furnace use must be of a non-cokiog kind, and, when of suitable quality, is perhaps the most advantageous fuel." In the first

Jan 1, 1892

By Marie L. V. Gayler

Without diffusion taking place in liquid metals and alloys, no castings could be made; it is therefore the most important factor affecting the structure of metals. Diffusion involves the interchange of atoms, a process which takes place during the life history of an ingot. In the liquid, atoms are in a state of high thermal agitation, but this thermal vibration is reduced in amplitude with falling temperature. When solidification sets in, the atoms arrange themselves on an ordered space lattice and the changes in structure which take place in the solid are due to the interchange of atoms on this space lattice. The rate of atomic interchange—e.g., of diffusion—is most rapid at temperatures close to the melting point and decelerates as the temperature is lowered. At room temperature, the rate of diffusion is practically negligible in most alloys, and any change in structure can only be brought about by using methods which will accelerate the rate of diffusion. The rate of diffusion depends on three factors (I) temperature; (2) concentration gradient and (3) activation energy. The growth of grains and particles in the solid alloy also depend on these factors and are therefore intimately associated with diffusion. The rate of homogenization in a cast alloy depends on several factors, such as: (I) rate of solidification, which involves grain and particle size which, in their turn, depend on diffusion: (2) the nature of the constituents; (3) the temperature interval between the melting point of the metal or alloy and the temperature at which it is being heat-treated. It is well known that coarse, cast structures are extremely difficult—if possible— to homogenize, and the finer the grain size and particle size, the more readily solid solution will take place. The rate of diffusion depends, also, largely on the nature of the constituents; for instance, copper and magnesium form solid solutions with aluminum quite readily but nickel and iron do not; neither do certain intermetallic compounds, such as alpha and beta FeSi. Furthermore, the actual formation of intermetallic compounds may be a very slow process, particularly when they are formed in the solid state as equilibrium products. For example, BFeSi is formed in the solid as the result of the reaction aFeSi + A1 —+ PFeSi. The particles of aFeSi become surrounded with a reaction ring of PFeSi. This layer is formed as the result of diffusion of atoms taking place between the aluminum matrix and aFeSi. As the amount of aFeSi surrounding the core of aFeSi increases the concentration gradient becomes low and so the rate of diffusion of atoms also decreases until it practically ceases. This occurs after a comparatively thin layer of ßFeSi has been formed. It follows that when intermetallic compounds of this type are formed in the solid, as the result of diffusion, it is generally impossible ever to attain equilibrium, since the forma-

Jan 1, 1944

By Marie L. V. Gayler

Without diffusion taking place in liquid metals and alloys, no castings could be made; it is therefore the most important factor affecting the structure of metals. Diffusion involves the interchange of atoms, a process which takes place during the life history of an ingot. In the liquid, atoms are in a state of high thermal agitation, but this thermal vibration is reduced in amplitude with falling temperature. When solidification sets in, the atoms arrange themselves on an ordered space lattice and the changes in structure which take place in the solid are due to the interchange of atoms on this space lattice. The rate of atomic interchange—e.g., of diffusion—is most rapid at temperatures close to the melting point and decelerates as the temperature is lowered. At room temperature, the rate of diffusion is practically negligible in most alloys, and any change in structure can only be brought about by using methods which will accelerate the rate of diffusion. The rate of diffusion depends on three factors (I) temperature; (2) concentration gradient and (3) activation energy. The growth of grains and particles in the solid alloy also depend on these factors and are therefore intimately associated with diffusion. The rate of homogenization in a cast alloy depends on several factors, such as: (I) rate of solidification, which involves grain and particle size which, in their turn, depend on diffusion: (2) the nature of the constituents; (3) the temperature interval between the melting point of the metal or alloy and the temperature at which it is being heat-treated. It is well known that coarse, cast structures are extremely difficult—if possible— to homogenize, and the finer the grain size and particle size, the more readily solid solution will take place. The rate of diffusion depends, also, largely on the nature of the constituents; for instance, copper and magnesium form solid solutions with aluminum quite readily but nickel and iron do not; neither do certain intermetallic compounds, such as alpha and beta FeSi. Furthermore, the actual formation of intermetallic compounds may be a very slow process, particularly when they are formed in the solid state as equilibrium products. For example, BFeSi is formed in the solid as the result of the reaction aFeSi + A1 —+ PFeSi. The particles of aFeSi become surrounded with a reaction ring of PFeSi. This layer is formed as the result of diffusion of atoms taking place between the aluminum matrix and aFeSi. As the amount of aFeSi surrounding the core of aFeSi increases the concentration gradient becomes low and so the rate of diffusion of atoms also decreases until it practically ceases. This occurs after a comparatively thin layer of ßFeSi has been formed. It follows that when intermetallic compounds of this type are formed in the solid, as the result of diffusion, it is generally impossible ever to attain equilibrium, since the forma-

Jan 1, 1944

COUNCIL OF SECTION DELEGATES Nicholas A D'Arcy, Jr, Chairman (Southern California Section) Charles Chapman, Vice-Chairman (Florida Section) Ben H Parker, Secretary (Colorado Section) Frontier Refining Co Boston Bldg Denver 2, Colorado

Jan 1, 1956

By Oliver Ralston

DURING experimental study on the separation of a zinc concentrate from the heavy sulfide ores of Jerome, Ariz., a great deal of attention has been given to proper activation of the sphalerite content of the ore. The sphalerite at Jerome contains enough iron to class it as a marmatite, as picked specimens have only about 60 per cent. zinc, whereas pure zinc sulfide contains 67 per cent, zinc. This marmatite in large pieces is black in color, but in dry powdered state is brown. A flotation froth made from it has a silvery black luster in comparison with a brassy luster caused by chalcopyrite which occurs in the same ores. The sample used in most of the experiments described below consisted of about 3000 lb. of diamond-drill core from the zinc-bearing orebodies of the United Verde mine, and had the following analysis: PER CENT. PER CENT. Oz. PER TON Cu 0.695 A1203 0.83 Ag 1.30 Zn 6.17 S...:: 43.35 Au 0.02 Fe 36.23 CaO 0.46 Si02 9.27 Mineralogically, this analysis is calculated to the following, which is in agreement with the microscopic examination: PER CENT. PER CENT. Chalcopyrite 2.0 Schist 3.2 Marmatite 10.32 Quartz 8.2 Pyrite 73.0 Calcite 0.9 All samples were ground in a laboratory ball mill in order to leave about 3 per cent. on a 200-mesh sieve, fine grinding being essential to liberate the minerals in the ore. Most of the Jerome ores are so intimately crystallized that reasonably complete unlocking by grinding does not take place until 800 mesh is approached. Therefore, the 200-mesh grind adopted contains a considerable amount of locked mineral grains, but not so much as. to render impossible the preparation of commercial grades of concentrate:

Jan 1, 1929

By F. N. Rhines

Despite the large amount of study which has been devoted to the subject our present knowledge of the copper-oxygen system remains incomplete and unsatisfactory .in many respects. This applies particularly to those regions in which solid metallic copper exists. The primary object of the present paper is the contribution of new information relative to the solid solubility of oxygen (or cuprous oxide) in copper at atmospheric pressure, together with certain observations in the low-pressure regions of the system. It seems appropriate also to present a brief summary of the outstanding previous work on the constitution of mixtures of copper with its lowest oxide in order. to show the relation between the new facts and the system as a whole. The earliest recorded investigations of the copper-oxygen system are those of M. S. Lucas(l) $ and of M. Chevillot(2) in 1819 and 1820. Lucas believed that liquid copper is capable of dissolving its oxide, but neither he nor Chevillot was able to furnish convincing proof of this property. It was not until 1866 that T. Graham(3) definitely established the existence of such a solubility. Nine years later W. Hampe(4) measured its extent and roughly outlined the copper-rich portion of the system. The first really precise examination of the constitutional relationship between copper and cuprous oxide, however, was that of E. Heyn(5) who in 1900 published a temperature-concentration diagram covering the range from 0 to 10 per cent of cuprous oxide at atmospheric pressure. Within these limits of composition cuprous oxide was found to dissolve in liquid copper, forming at 3.4 to 3.5 per cent a eutectic which melted at 1065" C. R. E. Slade and F. D. Farrow(6) extended these studies to mixtures of higher oxygen content. They discovered that between 20 and 95 per cent of cuprous oxide the metal and oxide form two liquid phases at a monotectic reaction of 1195" C. The span of the biliquidal region diminishes slightly

Jan 1, 1934

By Hsun Hu

Three single crystal strips of a 3 pct Si-Fe alloy with approximately (110) [001], (210) [001], and (100) [001] orientations were rolled at room temperature to 30, 50, and 70 pct reductions in thickness. Their deformation and annealing textures were studied. In most cases, the change in texture upon recrystallization and subsequent growth can be described as rotations around the <I10 > axes. A < WO > rotational relationship was also observed. The temperature dependence of recrystallization textures was discussed. WhILE considerable data have been published on the rolling and annealing textures in silicon-iron crystals, very little study has been made on the texture formation at various stages of rolling deformation, and during the process of recrystallization. Dunn&apos; in some of his early works had studied the orientation of recrystallized grains in crystals cut out from lightly rolled (10 to 20 pct reduction) large grained sheets. He found that in most cases a third-order twin relationship exists between the crystal and the recrystallized grains. This orientation relationship actually corresponds to rotations around the <110> axes. The more recent studies of Dunn &apos; and of Dunn and Koh &apos;5 on the rolling and annealing textures in various silicon-iron crystals were concerned mostly with a cold-rolling reduction of 70 pct and annealing at 980OC for recrystallization. Reductions of similar magnitude were also employed by Walter and Hibbard in rolling columnar crystal aggregates of a silicon-iron ingot. A systematic study of the effect of rolling reduction on the deforma- tion and annealing textures is still lacking. Regarding the effect of annealing temperature on the texture formation, Dunn3 has observed a change in therecrys-tallization texture by annealing a 70 pct rolled (1 10) [001] crystal first at a low temperature then atahigh temperature. But the details of texture formation during the annealing treatments were not thoroughly investigated. The present investigation was undertaken to study the texture developments at various stages of rolling deformation and of the recrystallization process, so that a better understanding on the texture formation in silicon-iron crystals may be obtained. EXPERIMENTAL PROCEDURE The three single crystals used in the present investigation were selected from the group of single crystal strips previously prepared7 from a high grade commercial Si-Fe alloy with 3 pct Si. The thickness of these single crystal strips was 0.040 in. The orientations of the three crystals as determined by the X-ray back-reflection Laue technique are shown in Table I. Each of the three crystals was rolled at room temperature along the strip direction to 30, 50, and 70

Jan 1, 1962

NAME "Utah" is derived from the name of the Indian tribe, variously spelled "Yuta," "Ute," "Youta." "Uta." "Eutaw," and finally "Utah." It means "in the tops of the mountains," or "on the heights." The state emblem is the "Beehive," typical of industry. State nickname is "Beehive State." AREA Utah is the tenth state in area. It contains 84.990 square miles, of which 2.806 miles are water. When admitted as a territory in 1850. Utah included all the area from the east line of California to the summit of the Rocky Mountains between the 37th and 42nd parallels, which embraced practically all of the present state of Nevada, all of western Colorado, part of Idaho and part of Wyoming, in addition to the present area of Utah.

Jan 1, 1925

By C. E. Shoenfelt

Jan 1, 1942