Search Documents

By C. W. Phillips, D. N. Frey

A commercial Ti-Fe-Cr alloy, Ti-150, exhibits a martensitic transformation on cooling and two nucleation and growth reactions, one above and one below the Mg-Mf region, on isothermal holding below the single-phase ß temperature range. The reactions were followed by metallographic, X-ray diffraction, and microhardness methods. THE rapidly expanding engineering application of titanium and its alloys makes increasingly urgent an adequate knowledge of the effect of heat treatment on this material. The work herein reported is an attempt to determine certain aspects of the behavior of a commercially available alloy, Ti-150, during heat treatment. The alloy, with a nominal composition of 2.7 pct Cr, 1.3 pct Fe, 0.25 pct 0, 0.02 pct N, and 0.02 pct C, was received in the as-rolled condition as a 3/4 in. round. Slugs 0.11 to 0.12 in. thick were cut under a coolant using a silicon carbide wheel. Preliminary work established that the alloy consists of two phases, a (hexagonal close-packed) and /3 (body-centered cubic), at temperatures below 1750" to 1775"F, and of only /3 phase at higher temperatures. The slugs were heated for 1 hr in air at 1800°F to form a single-phase /3 matrix, then transferred to molten tin (1250° to 1650°F) or lead (1150°F and below) for isothermal holding. Holding temperatures ranged from 700° to 1650°F, times from 0.001 to 23 hr. The treated slugs were then sectioned, one part for metallographic examination and diamond pyramid hardness, the other, after deep etching to remove the high oxygen surface,' for comparative lattice parameter determination and X-ray phase identification. Hardness measurements were taken on the lightly etched surfaces of the metallographic specimens; a 1000 g load on a 136° diamond pyramid was used. Five impressions on each sample were made and the average of the hardness calculated. The use of microhardness measurements to follow the course of an isothermal transformation reaction is undesirable because of the possibility of wide differences in microconstituent hardness.' They were used in this case, however, because of the small amount of material available. At the higher transformation temperatures, where the above-mentioned objection was apparent, the readings were proportioned to correspond to the estimated ratio of transformed and untransformed constituents present. At lower temperatures, resulting in much finer microconstituents, the microhardness measurements were more uniform. The standard deviation of the mean of five impressions calculated from these latter values was 4.2 DPH. Employing 2a limits (probability 0.95) the experimental error of the hardness measurements averages was 8.4 DPH. The etchant used was composed of one part glyc-erol and one part 48 pct hydrofluoric acid." Of a number of etches tried, this one appeared most satisfactory. All micrographs were taken at 500X magnification and with oblique lighting to permit easier identification of the acicular structure resulting from rapid cooling. No advantage was gained by using polarized light for metallographic examination. Phase identification and lattice parameter measurements were made with a North American Philips high angle spectrometer in conjunction with a recording potentiometer. Considerable difficulty was encountered with some of the lattice parameter measurements because of the extreme broadness of the few diffraction lines obtained from samples consisting mainly of strained, untempered, quenched structures.

Jan 1, 1953

By Jose A. Ruiz

INTRODUCTION For heterogeneous non-catalytic solid-gas reactions carried out in fluidized bed reactors, nominal bed temperature is an average value between gas and solid. For highly exothermic reactions, actual particle temperature can be up to hundred degrees above termocouple temperature, since heat dissipate at slower rate than heat generation during some steps of transformation. These micro instabilities at particle level can displace thermodynamic equilibrium from the desired phase to others. This effect is important when relatively narrow range of phase stability exists, like in sulphation roasting of sulphides, where bed discharge contains, in addition to the desired sulphate others metastable phases such as basic sulphate and ferrite. For example, for copper-iron sulphide concentration roasted below 680°C, no cupric ferrite is formed, as shown by Jakob et al., therefore the separate Kellogg's stability phase diagrams Cu-S-O represent the roasting (Fig.l). At temperature above this one, like 760°C for example, phase stability changes from CuSO4 to the basic sulphate Cu0•CuSO4. Solid state reaction between Cu0•CuSO4 and Fe203 also occurs to form cupric ferrite, Cu0•Fe2O3, therefore the Cu-Fe-S-O Kellogg's phase diagram of Fig. 1 (continuous line) represents this condition of roasting. Although both Cu0•CuSO4 and Cu0•Fe2O3 are metastable phases under normal operating conditions of sulphation roasting(1-10% SO2, 1-10% 02 and 680°C, points A and B,Fig. 1) sulphation of these species and particularly ferrite are slow and limited due to diffusional control. This explain why reactors discharge contains several phases: CuSO4, Cu0•CuSO4, CuO•Fe203 plus small amounts of CuS and FeS due to the baclonixed conditions of fluidized bed reactors. The presence of cuprous ferrite due to reducing conditions inside individual particles also occurs, but in very limited extent at the reaction interface, as it is demonstrated by the low soluble iron levels of calcines. On the other hand, the presence of cupric ferrites can be explained only due to the higher temperature achieved by particles, since below 680°C cupric ferrite formation does not take place. [ ] This phenomena also occurs for others non-ferrous metal sulphides concentrates roasted under sulphation conditions, such as 7n, Co and Ni. Therefore the prediction of discharge composition of fluidized beds is not possible based only on kinetics and mechanistics models alone or purely thermodynamical considerations, since all factors should be integrated to describe the overall phenomena. SINGLE PARTICLE TRANSFORMATION Assuming a first order reaction with respect to the gas and zero for solid, such as

Jan 1, 1984

By Oliver M. W. Sprague

THIS gold problem is full of complications and can hardly be handled adequately or comprehensively in any short period of time. Perhaps I might begin by mentioning a few aspects of the subject about which I suppose there will be no disagreement. The first of these is that we already have a stock of monetary gold in the United States far in excess of what is needed to support any desirable increase in the present volume of currency and credit. The second is that this already superabundant gold stock is certain to be considerably enlarged during the course of the war, and presumably during the months of readjustment following its conclusion. Some billions of additional gold, we may reasonably presume, will come into the country during these next few years, thus increasing the aggregate monetary gold stock from the present eighteen billions to perhaps twenty- two or even twenty-five billion dollars.

Jan 1, 1940

By J. W. Taylor, E. G. Zukas

THE results of shock-loading studies on copper were reported several years ago by smith. In his experiments, Smith found that there was a correlation between the shock direction and the orientation of twins which the shock produced. By using free-surface-type shots in which the free surface of the specimen was not normal to the shock direction, he showed conclusively that twinning of copper in impulsive loading was caused by the rarefaction wave. Similar tests with iron, however, showed that it twinned during compression. More recent studies of iron2 and on Fe-Si single crystals3 have shown that twinning can be suppressed in these materials by shock loading at pressures high enough so that the velocity of the shock wave exceeds the elastic-wave velocity. From these observations, it appeared that twinning was caused by the shear stresses present in the zone undergoing adjustment from one-dimensional to three-dimensional loading. At high pressures, such a zone becomes so thin that there is insufficient time for the relatively ordered motion of atoms involved in twinning to occur. Twinning in copper, therefore, cannot be produced by a single compressive shock wave because resolved shear stress large enough to create twins exists only for a very short time (0.01 psec or less) before the pressure increases suddenly and loading becomes essentially hydrostatic. (A typical pressure vs time record for a copper shot, illustrating the short rise time of the compression wave, is shown in Fig. 1.) If, on the other hand, a second shock wave can be created in a precompressed sample, then the new elastic limit is several kilobars,4 and a resolved shear stress sufficient to cause twinning should be maintained for an adequate time period (0.1 psec or more). This experimental situation can, in fact, be realized. The experimental arrangement used to do so is shown in Fig. 2. By utilizing the pressure transformation in Fe-V alloys, it was possible to shock-load the copper in compression while the copper was already precompressed. In the first test, an 8 wt pct V-Fe sample was used as a driver for loading the copper, and the copper was exposed to the following series of compressive shocks: 1) an elastic wave of about 8 kbars, which is usually ignored in shock studies; 2) the pressure transformation wave for the driver of 200 kbars; and 3) the driving shock wave of 270 kbars pressure. Metallurgical determination of the angular twin distribution, shown in Fig. 3, with respect to the shock direction and the shock rarefaction direction (which was 23 deg from the shock direction) showed that twinning took place

Jan 1, 1965

By Paul H. Price

The history of the salt industry in West Virginia dates back nearly two hundred years; however, the history of salt as an important raw material for the chemical industry is much more recent. The earliest record of West Virginia salt was in 1753, when a raiding party of Shawnee Indians attacked frontier settlements in Virginia taking captive a number of the pioneers. One of these, who later escaped and returned to her friends, described how the Indians camped at a salt spring on the banks of the Kanawha River and evaporated the water to obtain a supply of salt to take back to Ohio with them. Settlement of the Kanawha Valley began in 1774, that same year the Battle of Point Pleasant ended the Indian's power in the Ohio Valley; and settlement of the Kanawha Valley progressed rapidly with a consequent increase in the importance of the Kanawha Licks as a source of salt. In those days the evaporation of the brine was a family matter for which the family wash-kettle was commandeered.

Jan 1, 1949

By R. S. Shoemaker, F. W. McQuiston

SOUTH AFRICAN MILLING PRACTICE All modern South African gold plants operate primarily on the principle of exposing the gold particles in the ore by fine grinding and then cyaniding the total pulp. Although there are minor variations and occasional depart- ures from established practices among the fifty gold mines in South Africa, the normal plant operations proceed as follows. After removal of waste rock by hand sorting (15Y0 on average) the ore is crushed in cone crushers to minus 1/2 inch and then ground to approximately 75% minus 200 mesh by milling with either rod, ball or pebble mills as primary units and pebble mills for the secondary grind. Classification in both circuits is almost invariably conducted with 20" cyclones of 30" or larger diameter. Gravity concentration in the milling circuit followed by barrel amalgamation of the concentrates is practiced in 70Y0 of the plants, particularly where the ore grade is high. A slightly better overall recovery is obtained than with direct cyanidation, but additional handling is involved. Johnson cylinder s , plane tables or belt concentrators, all lined with suitable types of molded rubber riffles, are used for this purpose. At all mines, cyanidation is the main process, usually conducted by continuous treatment in Pachuca tanks and pulp separation with rotary drum filters. Cyanide solutions contain about 0.0 1570 NaCN and require a protective alkalinity of 0.02070 CaO. Precipitation of the gold from cyanide solution is exclusively by zinc dust and lead nitrate using the Merrill-Crowe system in conjunction with Stellar pressure filters. The zinc precipitate is smelted, generally after a preliminary concentration by sulfuric acid, in electric furnaces, mostly submerged arc types, with a silica and borax flux, yield- ing a bullion of 8870 gold, 9% silver, and 370 base metals. The gold content of the ore varies between 0.20 and 1.0 oz Troy per short ton and extraction efficiency ranges from 9570 to 9870. In general, 4070 of the gold output is recovered by amalgamation and 6070 by cyanidation; but in some cases, it is entirely by cyanidation. Flotation has not been adopted for gold extraction as it has not proved as efficient as cyanidation. It is, however, often applied to ores containing higher than 1% sulfur for the recovery of pyrite for sulfuric acid production. On the eastern side of the Witwaters rand Basin, "run-of -mine milling” was introduced in 1960 and in three of the four mills in this area both sorting and crushing have been eliminated. The ore received from the shafts is conveyed to storage silos and then fed by Williamson automatic feed controllers to pebble mills ranging from 12 to 14 feet diameter, and 16 to 20 feet long. The pebble mills operate in closed circuit with 42 inch cyclones and the slime produced is thickened and cyanided in the conventional manner. No selective

Jan 1, 1975

By A. M. Gaudin

TEN years ago Taggart, Taylor and Ince1 described a workable, convenient apparatus for the measurement of contact angles be-tween cleaved, ground or polished particles and captive bubbles. Wark and Cox2 and Wark and Sutherland3 have done an im-mense amount of experimental work with this apparatus. Their work has had as principal object the determination of "con-tact curves." Contact curves are Cartesian charts in which pH (or some other variable) is plot-ted against quantity of modifying agent. The rectangular area is broken into two or more curvilinear areas separated by the contact curve. The curve indicates that a sharp demarcation exists between condi-tions that bring about sticking of particles to bubbles and conditions that do not pro-duce sticking, The type curve appears in the TRANSACTIONS as Fig. 1, page 248, volume 112. Wark and Cox offer data to show that the contact angle has a value determined by and characteristic of the agent used. Wark and Cox also make the statement that they believe this value is independent of concen-tration (ref. 2a, p. 209), They say: It is suspected that, given sufficient time and provided that there are no disturbing factors. the full ethyl xanthate angle (corresponding to a complete xanthate film) would be obtained in every case where contact occurs.

Jan 1, 1940

By OTTO HERRES

TO operate the bituminous coal industry in the United States in 1929 cost $770,237,000, of which $30,739,000 was paid for purchased power and $34,947,000 for new machinery and equipment. Equipment aggregated 3,124,000 hp. A mining industry that spends $65,000,000 a year for power and machinery is likely to be fairly well mechanized, and when the machinery in use takes three million horsepower to drive it, the probabilities are that mechanization has been in progress in at least some of the mines for quite a few years. Mechanization in its broadest sense implies machine cutting, power drilling, mechanical loading, electric haulage, mechanical sizing and cleaning, and lesser applications of machinery to mining operations. But the introduction and development of mechanical loading has been the feature of coal mining recently and its extraordinary progress is causing great changes within the industry. First, let us look at the records. The quantity of coal loaded mechanically in bituminous mines was:

Jan 1, 1933

By S. S. Shen, M. J. Pool, P. J. Spencer

Heats of solution of gold and copper in dilute Au-Cu-Sn alloys have been determined using a liquid metal solution calorimeter. The self-interaction coefficient, Au - has been calculated at constant copper concentrations and n cu has likewise been determined at constant gold contents. Good experimental agreement is obtained between the interaction coefficients and nAu Cc thus demonsbating the reliability of the measured heat values. The measured data are compared with the Predictions of certain solution models. In previous publications,1,2 the results of calori-metric investigations of dilute Ag-Au-Sn and Ag-Cu-Sn alloys have been presented. The present work on the Au-Cu-Sn system concludes a program of studies of enthalpy interaction coefficients in dilute alloys of the Group IB metals with tin. Since the definition and derivation of an enthalpy interaction coefficient has been discussed previously,1,2 no restatement of this theory will be presented here. From the determination of the partial heat of solution of gold and copper in ternary alloys of various copper and gold contents, values of the interaction coefficients can be calculated. These coefficients give an insight into the various solute interactions that occur in the liquid solutions since changes in their magnitude and sign reflect bonding changes that are taking place in alloys of varying solute contents. EXPERIMENTAL Details of the design and operation of the liquid metal solution calorimeter used in this work may be found in a paper by Poo1.3 For the present studies copper of 99.999 pct purity was supplied by American Smelting and Refining Co., gold of 99.999 pct purity by A. D. Mackay, Inc., and tin of 99.99 pct purity by Baker Chemical Co. At the commencement of each series of experimental drops, a tin solvent bath consisting of between 70 and 90 g of the pure metal was inserted in the calorimeter. The weight of the bath was accurately determined and to it were added appropriate amounts of gold or copper to give alloys of the desired composition. For determinations of approximately 0.0015 g-atom samples of Cu were used and for measurements of ?HAu approximately 0.0025 g-atom additions of Au. The heat capacity of the bath was determined at regular intervals during a series of drops using tin calibration samples. Measurements were made of the heat of solution of copper in alloys containing a constant 0.01, 0.02, 0.03, and 0.04 mole fraction of Au, respectively, in order to determine ?HCu in each alloy, and the same mole fractions of copper were used to determine equivalent values for nAu at constant copper concentrations. The composition of the bath was maintained at the desired constant gold or copper content by making calculated additions of the appropriate solute throughout the experiments. The limiting values ?HAu in alloys of constant copper content and of %c, in alloys of constant gold content were studied as a function of the mole fraction of copper or gold respectively in order to determine and nCu. Heat content and heat capacity data used in calculating values of ?ºHAu and ?HCu at the experimental temperature of 720°K were obtained from Hultgren et a1.4 ' RESULTS AND DISCUSSION Determinations of ?HAu. The partial heat of solution of gold in pure tin as a function of gold concentration was determined in the previous study of dilute Ag-Au-Sn alloys1 and can be represented by the least-squares expression: ?HAu(l) =-8075 + 2413xAu [l] which is valid between XAu= 0.00 and xAu = 0.05. The standard error in the constant term, which represents the partial heat of solution of gold at infinite dilution in tin,?HºAu(l)is 35 cal per g-atom, while the standard deviation of the slope, which represents n Au is ± 619 cal per- agtom. Corresponding expressions for ?HAu(l) in alloys containing constant mole fractions of 0.01, 0.02, 0.03, and 0.04 copper were obtained from the data listed in Table I and are themselves given in Table II. Fig. 1 illustrates the partial heat of solution of gold as a function of its concentration in each of the alloys. For the four alloys of constant copper concentration, the values obtained for ?HºAU(l) (in order of increasing copper content) are -8141 i 36 cal per g-atom, -8210 ± 42 cal per g-atom, -8202 ± 46 cal per g-atom and -8268 ± 51 cal per g-atom. The corresponding values of the self-interaction coefficient, n Au, for these alloys are 3103 * 644 cal per g-atom, 2425 ± 676 cal per g-atom, 2574 * 717 cal per g-atom and 2523 ± 899 cal per g-atom. In Fig. 2 these values of n Au are plotted as a function of the copper content of the alloys and are seen to remain approximately constant within the experimental limits. The addition of increasing, small amounts of copper to dilute binary Au-Sn alloys thus has no apparent effect on Au-Au interactions in these dilute liquid solutions, although more exothermic values of ?HºAu(l) do result from an increase in the copper content of the alloys. Analogous behavior was observed with additions of silver to dilute Au-Sn alloys.' By

Jan 1, 1970

By L. Adler

Any design of a mine roof in bedded deposits which ignores differential deflections at the supports can quickly lead to dangerous overstressing. As illustrated by the typical case presented on page 1029, if one support deflects only 0.1 in. more than its neighbor, stresses 50 pct higher than anticipated will result. Previous studies1-3 have assumed that the mine roof acts like a beam clamped at both ends, with no deflection or slope' at the supports (Fig. 1). Essentially this assumes:5* ?A = ?, = ?b and dA = dB = 0. However, a host of conditions can cause differential sag or deflection at one support, and even an apparently trivial deviation can have major consequences in the beam: variations in spacing, size, and material of supports; local settlement due to floor heaving or lower mine openings; non-uniformity in wedging or bolt tensioning.8 In one particular instance concrete pillars, poured in place, shrank away from the roof upon setting.' When understood and controlled, differential sag becomes a definite advantage, permitting the transfer of loads from one support to another. Where one support is a bolt or prop and the other a pillar or rib, the load on the former can be reduced while the load on the pillar or rib is increased. This means two things: 1) savings can be effected by using smaller artificial supports such as props and bolts and 2) loads can be increased in the rib to induce eventual failure for longwall caving. In this last respect, another factor underlying coal bumps becomes understandable. The design of a mine roof by beam theory assumes that when a bedded formation is homogeneous, iso-tropic, and elastic, it will act like a uniformly loaded beam, fixed or clamped at both ends,6 s in Fig. 1.'" These are important assumptions. The uniform load is the weight of the beam itself or its body load. For a beam of unit width, this load becomes per foot: w = yhb. w = uniform load y = specific weight, lb per ft3 h = depth or thickness of beam, ft b = width of beam, ft Since b = 1, w - yh [ 1 ] A beam fixed at both supports is statically indeterminate to the second degree, that is, two equations in addition to those for static equilibrium are required to determine the reactions at the supports. These equations result from the geometry. From statistics: ^F,= 0;RA + RB — wL = 0 [2] wU S,M0 = 0 ; MB H------------MA — RBL = 0 [3] it Using superposition in which the left support is kept intact and the right one resolved into an active force and moment, we obtain from Fig. 2:" ?b = ?m + ? b2 + ?B3 = 0 dB = dB1 + dB2 + dB3 / wU Ma RBL \ V d°=(-r+-2—r)-zr [5] Where: Subscripts refer to position on axis of beam R = force, lb M = moment, ft-lb w = uniformly distributed load, lb per ft L = span, ft 0 = slope, radians d = deflection, ft E = Young's Modulus, lb per ft" 1 = Moment of inertia about the neutral axis, ft4 Solving Eqs. 2 through 5 for the four unknown reactions, we obtain: 2 L3 Fig. 3 is obtained by plotting MA and M, vs d, and then plotting RA and R, vs d, and adjusting their scales to coincide with MA and M, vs d,. It should be noted in Eqs. 6 and 7 that as dB increases, MA increases the same amount that Mn decreases. Eqs. 8 and 9 show a similar relationship between RA and R,. Proof that MA is the maximum absolute moment occurring in the beam is as follows: where M, = moment at x wx-When where M,., = maximum positive moment Eqs. 6 and 8 into above: For small dn: MA> M,,,

Jan 1, 1960

By Hon. Tasker Oddie

DURING the closing days of the last Congress a resolution was passed, creating the Senate Com-mission of Gold and Silver Inquiry. The resolu-tion charges the Commission with the responsibility to investigate and report to the Congress on Jan. 1, 1924, upon the following subjects: 1. The causes of the continuing decrease in the production of gold and silver. 2. The causes of the depressed condition of the gold and silver industry in the United States. 3. The production, reduction, refining, transportation, mar-keting, sale, and uses of gold and silver in the United States and elsewhere. 4. The effect of the decreased production of gold and silver upon commerce, industry, exchange, and prices. The personnel of the Commission is as follows: Senators Pittman, Sterling, Goodling, Walsh and Oddie. At a meeting on May 8, H. N. Lawrie, a mining engi-neer and economist, was appointed as Assistant to the Commission. The present situation with respect to the gold and silver mining industries is well illustrated by the follow-ing data: The total world production of gold (in dollars) for 1915 was $468,724,918, and for 1921, $329,915,101; as shown by the reports of the U. S. Mint; and for the year 1922, $306,793,000, which is based oh a prelimi-nary estimate; this indicates a decrease of 34.5 per cent. between 1915 and 1922. The total world production of silver (in fine ounces) for 1915 was 178,850,000 oz.; for 1921, 175,268,234 oz., a decrease of 2 per cent.

Jan 6, 1923

By John J. Collins

The plight of the Japanese mining business is pitiful. Coal mines were given the highest priority for all materials they needed, yet between the end of the war and June 1948, the government was obliged to subsidize them to the extent of 22 billion yen, this being the difference between the consumer's price and the producer's price. Most of the metal mining companies have been operating at only one fifth to one third of war-time production rates, and financial losses have been terrific. The chief difficulties have been a plethora of office workers and a dearth of equipment, supplies, and miners. The principal material needs at metal mines are steel rails. cars, plates, nails, rubber hoses, and belting, to say nothing of modern core drills which are totally lacking. Until recently the great shortage was in coal; for lack of fuel the smelters and factories failed to produce the very metals and equipment now needed to operate the mines. Nation-wide shortages have created a monstrous inflation of prices throughout all the economy, currently amounting to 200 times the prewar figures. For example, the price of copper ranged from 500 to 900 yen per metric ton for many years until 1937, but in mid-1948 producers were

Jan 1, 1949

By George H. Hanna

THE importance of the Donets coal field (the Donbas) to the national economy of the Soviet Union is well known. Great as was the significance of this tremendous deposit of coal in prewar days it is destined to become an even greater factor in the economic life of the country now that the tremendous havoc wrought by the Germans is being remedied. Since the war began, new coal fields have been extended; for example output of the Moscow and Karaganda (Kazakhstan) fields has become considerably larger while new mines are producing coal in several parts of Uzbekistan and Kirghizia. The huge West Siberian coal field, the Kuznetsk Basin, is producing more coal than ever before to supply the industries of that region and of the Urals. But so great has been the development of industry to meet war needs, especially in those districts of the Soviet Union that lie to the East of the Urals, that the coal obtained, eked out by such locally-won fuels as peat and wood, is still barely sufficient to meet industrial requirements. The main burden of the coal supply for the restored industries of the West, therefore, will fall on the Donbas.

Jan 1, 1945

By R. J. Hopkins, L. B. Haney

On the basis of limited experimental work conducted at the Port Pirie smelter, it would appear that, by increasing the specific surface of sinter, and possibly that of coke as well, a marked increase in the rate and degree of sinter reduction in the furnace shaft can be achieved. Fusion-point tests have shown that this increased reduction means a much higher sinter fusion point and narrower plastic zone, while the more efficient utilization of coke in the furnace is inherent in the intensification of reduction by the provision of a more reactive sinter surface. Investigations aimed at increasing the ability to operate the blast furnace with a higher lead tenor of sinter reducing fuel cost proportionately, and at eliminating the loss in reduction potential in coke entering the furnace, as shown by the presence of appreciable proportions of CO in the top gases, are reported. Several lines for future investigations that could result in improved smelting methods are proposed. A SOMEWHAT informal presentation of ideas on lead blast-furnace smelting will be given in this paper. These ideas have been developed during observations of furnace behavior at Port Pirie and earlier at Mt. Isa, and have been guided by the results of laboratory experiments at Port Pirie. The authors do not intend to propound any particularly new theories, but present their ideas as a basis for discussion which may help toward a better understanding and improved control of blast-furnace operation. Performance variations of considerable magnitude occur from time to time at most lead blast-furnace plants. While Port Pirie is fortunate in having a very regular supply of high grade concentrates, it is no exception in this respect. Such irregularities are of considerable economic importance and they constitute a challenge to present-day metallurgists in their efforts to obtain an ever greater degree of control over furnace operation. In operating as Port Pirie does with a relatively high lead charge, it has been recognized for a long time that shaft conditions are ,of the greatest importance. A practical, or engineering, attack on the problem of accretions consisted of changes in furnace design, e.g., by widening the shaft to 10 ft above the bottom row of tuyeres, and by the provision of curved ends and vertical walls.' That this attack has had a great measure of success is shown by the fact that barring down of these wide furnaces is rarely necessary, shaft conditions have greatly improved, and sensitivity to charge variations has been markedly reduced. These modifications, followed by some metallurgical changes (chiefly the incorporation of pig iron into the furnace charge in 1948), have brought furnace operation to a point where some variables which were previously masked can now be studied. Accordingly, over different periods of time during the last five years, such variables as could be given numerical values have been recorded and subjected to statistical examination. The objectives of this work were: 1—to reveal the true importance of the different variables and 2—to show the proportion of total furnace variation which is unexplained and therefore referable to causes not measured at present? e.g., shaft accretions, sinter structure, coke structure, and others. Statistical Study of Variables In this work factors relating to furnace speed and lead reduction have been examined: 1—slag com-

Jan 1, 1955

By A. Gatti, R. L. Fullman

A very fine dispersion of aluminum oxide is produced by internal oxidation of solid-solution alloy of 0.14 pet A1 in Ag. The particle size of the aluminum oxide is approximntely 50 to 100A in radius. The yield strength of the alloy is increased markedly by internal oxidation. A further increase in strength is produced by cold working the internally oxidized alloy. Recrystallization is retarded by the finely dispessed aluminum oxide particles, so that the strength increase resulting from cold work is retained on annealing at temperatures 14 to about 700°C. MANY workers'-3 in the past have studied various aspects of the internal oxidation of aluminum-silver alloys. This paper is an extension of these studies with emphasis placed on the effect of time and temperature of annealing on the strength of these alloys after oxidation and subsequent cold working. Two general conditions are necessary to internally oxidize an alloy. First, oxygen must diffuse through the base material more rapidly than does the addition; otherwise oxidation will take place as a surface layer. Secondly, the affinity of oxygen for the addition must be greater than for the base material. After internal oxidation of certain alloys takes place, a marked increase in hardness accompanied by higher yield stress and improved creep properties is noted, presumably as a result of the highly dispersed oxide within the base material. Meijering and Druyvesteyn1 also noted that the internally oxidized portion of a partly oxidized alloy failed to recrys-tallize under annealing conditions that led to coinplete recrystallization of the unoxidized part. EXPERIMENTAL-METHODS AND PROCEDURES Few alloys can be made to contain a second phase that is extremely stable at high temperatures. Silver plus aluminum in solid solution was chosen for these internal oxidation studies because of the high rate of oxygen diffusion through silver and the very stable nature of aluminum oxide. Two alloys were vacuum cast. The nominal compositions were: Alloy A—1 pct Al, balance Ag; Alloy B—0.1 pct Al, balance Ag. Chemical analysis, which does not distinguish between aluminum and aluminum oxide, showed the conlposition to be: Alloy A—1.6 pct Al, and Alloy B—0.14 pct Al. The ingots were machined for surface cleaning, swaged and drawn to 0.020-in. diam wire. A sample 20 ft long of the 0.020-in. dianl wire of each composition was annealed 24 hr at 800°C in pure dry hydrogen. Each wire was then cut into two equal pieces. Photomicrographs of the 0.14 pct A1 alloy are shown in Fig. 1, the annealed 0.020-in. wire at the left and the oxidized wire to the right. The oxidation treatment for the first set of data was 1000 hr at 800°C in air. After this treatment the 1 pct A1 proved to be brittle. It is assumed that high alunlinum oxide concentration at the grain boundaries was responsible. The 0.14 pct Al wire remained ductile and all further data were derived using this alloy. One-half of this wire, about 5 ft, plus 5 ft of as-homogenized wire, was then drawn cold to 0.005 in. diam. All tensile tests were conducted with an Instron Engineering Corp. tensile-testing machine, Model TT-B. Unless otherwise indicated, the tests were made at room temperature with a strain rate of 0.1 per min. All metallographic samples were etched with an aqueous solution of 2 pct each of CrO3 and H2SO4 . EXPERIMENTAL RESULTS AND DISCUSSION PARTICLE SIZE DETERMINATION A study was made of the particle size of the aluminum oxide produced in the samples of Ag + 0.14 pct Al, oxidized 1000 hr at 800°C. A cross section of the as-oxidized wire was mounted in bakelite, polished, and etched with an aqueous solution of 2 pct each of CrO3 and H2SO4. The specimen was then thoroughly cleaned by stripping successive coatings made by applying 10 pct nitrocellulose in amyl acetate. The final replica of the cross section was made by applying 2 pct nitrocellulose in amyl acetate. The replica was stripped, transferred to a copper screen, shadow cast with chromium at 10 deg and photographs taken using a Phillips Metallix electron microscope at an accelerating potential of 100 kv. A photograph of an etched sample of the as-oxidized material is shown in Fig. 2. We believe the pits in the photograph are places were A12O3 inclusions were sitting in the matrix. By inspection, it appears that the volume fraction ob-

Jan 1, 1960

By O. A. Kiehn, C. A. Born, F. N. Bender

Development of the flotation reagent scheme at Climax Molybdenum Company's mine at Climax Colorado is reviewed. Features of the mineralogy, milling practice and background of reagent changes are outlined. Special attention is given to the hitherto unpublished details of the application of depressants for copper and lead impurities. The present rougher flotation reagent scheme utilizes a neutral hydrocarbon oil, low in unsaturates and wax, as collector with a sulfated coconut oil emulsifier and pine oil frother. Lime and sodium silicate are used as rougher conditioning and slime dispersant agents. Chalcopyrite and galena impurities are depressed in both rougher and cleaner plants by stage addition of Nokes reagent and sodium cyanide to yield a metallurgical grade molybdenite concentrate containing greater than 90% molybdenite and less than 0.5%, 0.1% and 0.05% iron, copper and lead impurities, respectively.

Jan 1, 1976

MINING AND METALLURGICAL SOCIETY OF AMERICA San Francisco Section The San Francisco Section of the Mining and Metallurgical Society of America held a joint meeting with the local section of the American Institute of Mining Engineers at the Engineers' Club, San Francisco, on Tuesday, Apr. 16, 1918. The meeting was preceded by a dinner. Letters from the parent body in NewYork asking for the consideration of the proposed bill before Congress, and an expression of opinion relative to the appointment of a Federal Administrator of Mines justified the joint meeting of the local sections of the two mining societies, in that a more representative opinion of the engineers of California could he obtained. The meeting was called to order at 7:15 P.M. by Mr. Frank H. Probert acting as Chairman. About thirty engineers were present. Mr. Probert read a letter of March 14, from Secretary Huntoon, asking that the meeting be called. He read excerpts from Bulletin 117 of February 28, 1918, of the Mining and Metallurgical Society containing a copy of the proposed bill, so that all present might be advised of its essential contents. He briefly commented on the urgent need of such legislation and invited discussion of the subject. After long and thorough discussion on the part of the members present, Professor Lawson made the following motion: I move that a resolution expressing the sense of the joint meeting of the local sections of the American Institute of Mining Engineers and Mining and Metallurgical Society of America be forwarded to the secretaries of the two societies to the effect that we heartily approve of the purpose and intention of the bill designed to promote and stimulate the production of minerals necessary for the successful prosecution of the war; and that we suggest prices should be fixed for the period of the war and two years thereafter, and that these prices, guaranteed by the Government, should apply at the nearest shipping point to place of production of the minerals. This motion was carried. The meeting then adjourned, and a telegram was sent by Mr. Probert, the Chairman, to Mr. Huntoon, notifying him of the motion that had been carried at the meeting.

Jan 7, 1918

By J. A. Berge, R. S. Mateer, R. G. Aspden

IN a study of the cold-rolling characteristics of iron-base alloys with 3 to 12 pct Al, the influence of aluminum content on the cold-rolling textures was evaluated. This work was undertaken to determine if binary iron-aluminum alloys possessed cold-rolling textures similar to other body-centered-cubic alloys and to contribute additional information on the effect of solute concentration on the cold- rolling textures. Gradual changes in cold-rolling textures with an increase in solute content have been observed in copper1 and in titanium.2 Iron-base alloys containing 3.0, '6.0, and 12.0 pct aluminum were vacuum-induction-melted in a magnesia crucible and permanent-mold cast. The materials used were high-purity electrolytic iron and 99.99 pct grade aluminum. Each ingot was 1 in. square in cross section by 12 in. in height. The bottom half of each ingot was soaked for 1 hr at 1000°C and rolled at 1000°C to a thickness of 0.055 in. with the long axis of the ingot parallel to the rolling direction. The strip was reheated between passes to maintain a rolling temperature of 1000°C.

Jan 1, 1960

By George S. Barnett

The Equis and El Roble projects are located in the Cordillera Occidental of Colombia. The Equis vein deposits have sulfide ore reserves of 95,955 mt (105,770 st) grading 8.51 g/mt (0.248 oz/st) gold and 12.4 g/mt (0.36 oz/st) silver with 0.94 % copper, 1.10 % lead and 11.06 % zinc. Ore reserves at El Roble are estimated as 1.1 Mmt (1.21 million st) grading 4.89 % copper and 3.39 g/mt (0.099 oz/st) gold. Geologically possible reserves at Equis may total 1.6 Mmt (1.76 million st). El Roble has the potential to contain several tens of millions of metric tons. Exploration included diamond drilling, trenching, channel sampling, rock and soil geochemistry, geophysics and tunneling. Erratic high grade samples affect the weighting of channel and drill core samples. Secondary reconcentration of gold is also a factor. Sample maps and graphs show the distribution of values to be highly variable. Geostatistical treatment of some of these data gave important guidelines for parameters such as sampling densities, drill hole spacing and confidence limits.

Jan 1, 1985

By Odmund Ljone

FAR north of the Arctic Circle is a totally industrial community which until 1945 could not boast a single specimen of the rat family, and where today you will be awarded a bottle of fine cognac for every rat-dead or alive. Amazing but true, the spot is Longyear City, the Norwegian mining town on the arctic island of Spitzbergen. Perhaps you have also heard of the town built on soil that never thaws, where huge blocks of ice must be melted to fill the city's fresh water reservoirs, and where the Far North dictates a way of life all its own. Here, coal is king and men must work hard for their "black gold." Spitzbergen is a rough, tough piece of Norway, made up of a half dozen isolated islands between 74 and 81 degrees north latitude. Covering twice the area of Belgium, they are home to

Jan 1, 1948