Search Documents

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 33? per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 Per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. Mine Power at 13.8 kv. enters the mine through a ventilation raise over a three-conductor, size 1-0 varnished cambric insulated, leaded, steel-wire armored cable, insulated from 17 kv. This power is received and distributed through one switching station and four underground substations, shown in Fig. 2. No. 370 substation (Fig. 3) contains three a 13,800/440-volt, single- phase Pyranol transformers protected on the high-voltage side by a 600-amp. manually operated oil circuit breaker. This station serves 20 slusher-hoist motors, a 45-kw., three-phase, 220-volt electric furnace, a Massco hot miller for tempering and milling Timken detachable bits and a hoist with 175-hp motor on the No, 3 development shaft. Also at this shaft are three pumps. One two-stage pump, 1200 gal, per min., 500-ft. head, 3600 r.p.m., driven by a 150-hp. motor, is at the bottom of the shaft, Two deep-well pumps, 500 gal. per min., 500-ft. head, are at the collar of the shaft. under normal operation the one pumping 1200 gal. per min, is controlled by a float switch to take care of the water. If this pump fails, or if its capacity is insufficient, the first 500-gal. pump is automatically started1 and if still more capacity is needed the second 500-gal. pump automatically starts. Time delay relays are provided on the deep-well pumps, so that if power fails the column will have time to drain before the Pumps restart. On failure of any Of these, an alarm is sounded in the train dispatcher's office, so that mechanics can be sent to ascertain the cause of failure and make repairs. The cable from No. 37' substation is run to the switching station, in which are four 15-kv., 600-amp. direct-current sole-noid-operated oil circuit breakers. The current for Operating and tripping is furnished by a 125-volt storage battery. All breakers are operated from the switchboard in the compressor room. One circuit from this switching station goes to the

Jan 1, 1946

By E. P. Abrahamson

The effect of transition element binary solid solution additions upon the re crystallization temperature of nickel has been investigated. All additions raised the re crystallization temperature. Both the rate of change of re crystallization temperature with at. pet solute and the limit of initial linearity are found to correlate with the free atom ground state outer electron configuration of the solute element. A comparison of all of the correlations for the transition elements studied has yielded a set of empirical relations, which allows the prediction of the effect of dilute binary transition elements on the recrystallization temperature of other transition elements. The work of Abrahamson, et al.1-7 on dilute binary solution alloys indicated a correlation between the free atom ground state electron configuration of the solute and both the brittle-ductile transition and re-crystallization temperature. Further, it has been shown3,4 that the limit of initial linearity may also be correlated with the solute electron configuration. Since previous studies have dealt with bee and hexagonal base elements, this study is made to note what effect, if any, the fee base structure might have. Nickel also serves to give a solvent configuration which will allow the comparison of all of the transition element solvents. Olsen8 has studied the effect of some trace elements upon the recrystallization of nickel. He included only Ti, Zr, W, Mn, and Co of the transition elements. The differences in change of recrystallization temperature were attributed to the solute atom size and to the solubility of the solute in nickel. PROCEDURE All alloys were made using 99.9 + pet Ni with 0.003 C, 0.015 Fe, 0.007 0, and 0.0007 H. The solute elements were 99.9 + pet pure. According to the published binary phase diagrams9 and metallo-graphic examinations at X750, all solute elements were in solid solution. The alloys were arc melted and remelted four times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot forged at 800oC to 0.750 in. diam, machined to 0.60 in., vacuum annealed for 1 hr at 700°c, swaged to 0.40 in. and annealed at 700oC for 1 hr in vacuum. The grain size was checked and found to be 77 * 20 grains per sq mm. The specimens were then swaged to 0.187 in., yielding 76 ± 1 pet cold work. All alloys were then chemically analyzed for the solute addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The swaged rod was cut into 8.25 in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was maintained at 250" to 850°C over an eight inch length, recorded by twelve thermocouples. Control was ± 3oC, accomplished at the hot end. The recrystallization was determined metallo-graphically over the entire specimen. The criterion chosen was that point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be generally ± 3oC.

Jan 1, 1962

By John D. Roach

DURING an investigation of the yttrium-hydrogen system aimed at producing solid yttrium hydride specimens containing various amounts of hydrogen, it was observed that yttrium containing approximately 2 wt pct H exhibited a tendency to crack and crumble to a powder on standing in air at room temperature. It was also observed that longer hydriding times, at a given temperature, increased this susceptibility to powdering without an increase in hydrogen content, also that moisture in the air is necessary for the observed effects to occur. Even if cracking did not occur, there was a continual formation of a light gray powder on the as-treated surface of the hydrided yttrium and this reaction continues until the entire hydrided piece has been reduced to a powder. Storing the hydrided specimens in the absence of air or removing the surface either by machining or grinding were effective means of preventing this disintegration of hydrided yttrium. In an attempt to determine the reason for this powdering phenomenon, the surfaces of a number of as-hydrided yttrium specimens were examined by X-ray techniques. In all cases the X-ray pattern obtained showed the major phase to be yttrium hydride (YH2) as would be expected since the specimens contained 2 to 2.2 wt pct H. In some cases a trace of yttrium oxide was observed. There was also a third phase present on the surface of these hydrided specimens which could not immediately be identified. This unknown phase was a face-centered cubic material, NaC1-type structure, with a lattice parameter of 4.855 and a calculated density of 5.914 g per cc. Very slight hand polishing of the surface of the hydrided yttrium specimens completely removed both the unknown phase and the traces of oxide so that only the yttrium hydride pattern remained. Based on the X-ray patterns the quantity of the unknown phase on the surface of the hydrided yttrium appeared to be directly related to the susceptibility of the material to powdering. Work at the Denver Research Institute on the yttrium-nitrogen binary system showed that yttrium nitride (YN) is a face-centered cubic material with a lattice parameter of 4.878A and a density of 5.890 g per cc. They also noted that this compound rapidly disintegrated to a powder on standing in air. The unknown pattern observed in the above specimens corresponds very closely to that of the nitride—fcc structure, 4.885 parameter, and density of 5.914 g per cc. The presence of this thin film of nitride on the surface of the hydrided specimens probably accounts for the observed powder formation and crumbling. The nitride reacts with the water vapor in the air (verified by private communication from Dr. C. Huffine, General Electric Co.) to yield yttrium oxide and ammonia. Ammonia is readily detected when hydrided yttrium specimens were allowed to stand in bottled moist air. The powder formed on the surface of the hydrided specimens was shown by X-ray analysis to be yttrium oxide. This reaction appears to occur primarily at the grain boundaries since discrete particles of yttrium hydride separate from the specimens during this powdering process. The reaction of yttrium nitride with water vapor is believed to be as follows: 2YN + 3H2O - Y203 + 2NH3. Despite the fact that this nitride is present only as an extremely thin surface film, if the above reaction is not prevented by removing this film from the surface either by machining or grinding, the reaction continues until the entire hydrided piece has been reduced to a powder. To account for this continuation of the reaction, it is believed that the following reactionalsooccurs: 2YH2 + 2NH3 -2YN + 5H2. The nitride produced by the latter reaction reacts in turn with water vapor. The reaction therefore becomes autocatalytic and continues until the hydride has been consumed and the entire piece reduced to oxide powder. The amount of nitride required to initiate this reaction is quite small and this nitrogen contamination can occur from a number of sources—hydrogen gas employed, minute leak in the hydriding apparatus or even from degassing of the reaction vessel itself. Longer hydriding times increase the possibility of nitrogen contamination and this is especially true when a dynamic gas system is employed in the hydriding process. The production of stable, solid hydrided yttrium is dependent on the complete absence of nitrogen contamination during processing. If such contamination does occur, powdering of the hydrided product can be prevented by removing the nitride from the surface e.g. grinding or by preventing access of air to the pieces e.g. sealing in wax or plastic. The author wishes to express his appreciation to General Electric Co. for sponsoring this research and for permission to publish the results of work under Subcontract AT-93.

Jan 1, 1962

By D. S. G. Hanson

The Flin Flon Mine has been in production for over fifty years, and current mining is dependent on pillar and remnant recovery. One of the last major blocks of ore, and an important economic entity to the Mine, is the North Main Shaft Pillar. A rock mechanics program was initiated through under' ground instrumentation and other subsequent analyses, to establish the degree of instability as min¬ing progressed. Several studies have been and will be undertaken to evaluate the general stability, and possibly improve the chances of stability during pillar recovery. The North Main Shaft Pillar is immediately bounded by cemented cut and fill supporting rib stopes which inturn are bounded by slag and waste filled stopes. The min¬ing method involves a modified longhole open stoping and slag fil¬ling sequence for each mining block in a general mining upwards scheme.

Jan 1, 1983

By G. W. Healy

Activities of oxides in the ternary FeO-MnO-SiO system are calculated from data on the binaries, using the Gibbs -Schuhmann method. These activity data are used, together with thermodynamic relations, to calculate the contents of oxygen, silicon, and manganese in liquid iron, and the composition of the corresponding oxide phases in equilibrium with it. Excellent agreement was found between calculated and experimental metal compositions, indicating that thermodynamic methods, such as those presented, can supply useful data on slag-metal equilibria, and are therefore capable of wider application. When molten steel containing oxygen is treated with a deoxidizer, the product of the reaction is composed of the oxides of the deoxidizing elements together with more or less iron oxide. This assemblage of oxides is presumably very close to equilibrium with the melt since it is formed directly from elements dissolved in it. Therefore, it is likely that metal analyses corresponding to a given oxide phase composition are calculable with considerable precision where sufficient information is available on activities in both phases. The present study was made to test this hypothesis in the case of deoxidation by silicon and manganese. Here experimental data on the relationship among oxygen, silicon, and manganese in the metal phase are available, as are activity data for the MnO-SiO2, FeO-SiO2, and FeO-MnO binary systems. A further objective was to demonstrate in a specific example how gaps in the data may be filled by judicious interpolation, and how the Gibbs-Schuhmann method is applied to obtain activities in ternary systems. The rigorous derivation of the latter, requiring considerable facility in handling partial differential equations, tends to mask the real simplicity of the method, and repel the very engineers and experimenters who would benefit the most from its use. I) GENERAL PROCEDURE Deoxidation of steel with silicon and manganese results in the formation of two phases, metal and oxide. The number of components is four—Fe, Mn, Si, and 0. The phase rule then gives the number of degrees of freedom: If temperature and pressure are fixed, 2 deg of freedom remain. Consequently, it suffices to fix the concentration of two of the components of the system for all the concentrations to be determined and, at least in principle, calculable. The practical problem is then to discover a straightforward method of calculation with a minimum of trial and error solutions. The type of reactions to be dealt with are like the following: Si (in steel) + 2 O(in steel) = SiO2(in oxide phase) The standard free energy of this reaction is readily obtained from the literature, so that the equilibrium constant can be calculated by the expression: Since the metallurgist is concerned with percentages rather than activities, a real solution requires information that will permit activities to be converted to concentrations. This information is fairly adequate for the elements dissolved in molten steel, but is not available for the FeO-MnO-SiO2 oxide system. Therefore, the first step in this study was to find the relation between activity and concentration for the three oxides making up the system. The next step was the calculation of slag and metal compositions that are in equilibrium with one another. As shown by the phase rule, it is sufficient to assume the values of two composition variables in order to calculate the rest. But which two are picked makes a vast difference in how difficult the calculation turns out to be, so that it is necessary to make preliminary trial of several routes to find the easiest one. A convenient method is to begin with the slag, and to pick FeO concentration and that of one of the other oxides. Starting with the relation between oxygen dissolved in the liquid steel and FeO in the slag permits a good first estimate to be made of the oxygen content of the steel in equilibrium with FeO, because the iron content being fairly close to 100 pct, Fe has an activity close to unity. Using this first estimate of oxygen activity, approximate values of the manganese and silicon contents of the melt are readily calculated from the appropriate equilibrium constants. A minor correction for the depar-

Jan 1, 1963

By Mara Kosovac, Sujan K. Kundu

The Iron Ore Co. of Canada (IOC) has developed a computerized plan analysis method for its open-pit iron mining operations which will eliminate much of the tedious manual drafting of pit design plans performed by engineers and geologists at its two major operational areas near Schefferville, Que., and Labrador City, Nfld. The new technique permits analysis of section or bench plans for a specific ore body, based on drillhole information; preparation of a three-dimensional unit profit matrix for pit design purposes, and storage of extensive ore-block information for other applications. Other advantages include enhanced design accuracy through reduction of human errors normally associated with preparation of large data masses, and by elimination of errors inherent in planimeter-prepared ore block diagrams.

Jan 7, 1978

By L.W. Eastwood, Arthur E. Bousu, C. T. Eddy

The recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received considerable attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coalescence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presentcd in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are untenable. A paper on the theory of recrystallization, with additional data, will be completed in the near future by the writers. Since the literature on the subject has been adequately and frequently reviewed, the only referenccs to it in this paper will be those necessary in the discussion of the data presented.

Jan 1, 1935

By Arthur E. Bousu, C. T. Eddy, L. W. Eastwood

The recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received considerable attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coalescence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presentcd in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are untenable. A paper on the theory of recrystallization, with additional data, will be completed in the near future by the writers. Since the literature on the subject has been adequately and frequently reviewed, the only referenccs to it in this paper will be those necessary in the discussion of the data presented.

Jan 1, 1935

By Armando M. Lago

Secular and cyclical patterns of postwar sources and uses of funds of the mineral sector are analyzed. A simultaneous equation behavior model of sources and uses of funds is developed for both mining firms and integrated producers, and these models were put through the task of predicting the financial and expenditure be-havior of mineral corporations in response to mergers and changes in investment tax credits and depletion allowances. Finally, the quantitative analysis methodology is applied to the analysis of optimum capital structure of mining corporations. The postwar changes that have occurred in the expenditure and financial behavior of mineral corporations are reviewed, particularly the relative importance of factors that affect the industry's supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail. An econometric model of mineral corporate financial behavior is formulated. This model is then estimated and reviewed. Policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector are discussed. Finally, the optimum financial structure of mining firms is discussed and the effect of corporate financial structure on the mining corporations' average cost of capital is analyzed.

Jan 1, 1971

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By Emerson F. Heald

A systematic study was made of new and old data on chemical activities in Fe-Pt alloys at elevated ternperatuves. Experimental results may be expressed in terms of the excess free energy using Least-squares analysis of the data gave the following values for the constants: for the temperature range 1130° to 1350°C, and tentatively to 155O°C, B = -3.326564 and C = 0.221051; for the temperature range 650" to 850°C, B = -2.555690, C = 1.762735, and D =0.097196. In the study of iron-containing silicate systems, it is sometimes desirable to have a direct experimental measure of the activity of iron in the system. The well-known solubility of iron in platinum, often a headache in experimental work on iron compounds under reducing conditions, can be used to advantage in this respect. If the activity of iron in an Fe-Pt alloy in equilibrium with the silicate is known as a function of the composition of the alloy, chemical analysis of the alloy will give a knowledge of the activity of iron in all of the phases in the system. The present study was undertaken in order to elucidate the characteristics of Fe-Pt alloys as iron activity indicators. This work is intended to tie together some previous work, which may be summarized as follows. Larson and Chipman1 determined the activity of iron in Fe-Pt alloys at 1550°C by equilibrating platinum metal with calcium oxide-iron oxide-silica melts of known iron activity. Compositions of the resulting alloys were determined by chemical analysis. A similar study was carried out by Taylor and ~uan,' who worked at 1300°C. They brought the Fe-Pt alloys into equilibrium with iron oxide under conditions of known partial pressure of oxygen, and thus, from the work of Darken and ~urr~,~ conditions of known iron activity. Compositions were determined indirectly, by following the change in weight of the sample. Sundaresen et el* used the electromotive force of cells in which the alloy formed one electrode in order to measure the activity of iron in the alloy at 650" and 850°C. These temperatures were chosen to be above and below the first-order phase transition which takes place upon the ordering of Fe3Pt and the second-order transition which occurs upon the ordering of FePt3. EXPERIMENTAL 1) High Temperatures. The starting materials used were thin platinum foil, about 0.002 mm thick, and Fisher Certified reagent ferric oxide, Fez03, which had been heated for 24 hr at 1000°C. An intimate mixture of 80-mesh Fez03 and platinum platelets was placed in a thin platinum foil envelope. The latter was suspended from thin platinum wires in the hot zone of a vertical-tube, platinum-wound furnace of the type described by Muan and ~sborn.~ A capillary gas mixer similar to that used by Darken and Gurry3 was used to prepare a precisely known mixture of carbon dioxide and hydrogen, which was allowed to flow upward through the furnace tube. The partial pressure of oxygen in contact with the sample was thereby fixed at a value which was calculated from the charts prepared by porter? Temperatures were measured with a Pt-10 pct Rh-in-platinum thermocouple, which was calibrated using the melting points of gold (1062 .@C) and diopside, CaMgSizOB (1391.5"C). Temperature control was maintained to within i3"C with a Geophysical Laboratory proportional controller, using the furnace resistance as the sensing element. Samples were quenched by passing a small current through the platinum suspension wires, allowing the sample to drop into a bath of dibutyl phthalate at the bottom of the furnace tube. Prior to chemical analysis the samples were washed with acetone and dried. 2) Chemical Analysis. It proved possible, in almost all cases, to separate the Pt-Fe platelets physically from particles of iron oxide. The platelets were dissolved in a small volume of aqua regia, evaporated to dryness, and redissolved to 0.1 M HC1. In order to determine iron in the platinum alloy potentiometrically, it is necessary first to remove the platinum. A 10-cm column of Amberlite IR-120 cation exchange resin in the hydrogen form provided separation quickly and quantitatively: The mixture of iron and platinum in 0.1 M HC1 was added to the top of the column, and washed with about 100 ml of 0.1 M HC1. Under these conditions, the iron, principally in the form of cations such as FeC1" and FeCl;, is held quantitatively in the uppermost centimeter of the column. The platinum, in the form of anions such as PtC&- , is washed through without being adsorbed. After a qualitative test with stannous chloride indicated all of the platinum was removed, the iron was

Jan 1, 1968

By H. Y. Jennings

An extensive field and laboratory experimental program was carried out to compare the waterflood behavior of carefully preserved soft and unconsolidated cores with measurements on the same cores after extraction. Results obtained from using idealized consolidated and unconsolidated porous media in which wettability could be carefully controlled were contrasted with the preserved core data. The controlled tests on idealized porous media investigated the effect of wettability, flood rate, core length, core permeability and consolidation on the displacement of high viscosity oils. It was concluded from these studies that waterfloods are more favorable when carried out with crude oil in preserved soft and unconsolidated cores than with the same cores after they have been extracted and re-saturated. Waterfloods are usually more favorable when carried out with crude oil in extracted .soft and unconsolidated cores than with refined oil of the .same viscosity in the same cores. The less favorable behavior of extracted soft and unconsolidated cores compared to preserved cores is due to alteration of the core by extraction. Preserved cores saturated with native water and oil should be used for laboratory displacement experiments because they more accurately reflect true reservoir behavior INTRODUCTION The demand for low gravity crude oil created by refinery modernization has focused attention on increasing the production of this viscous crude oil. Billions of barrels are in place in fields that are depleted, or nearly depleted, by primary production mechanisms. Since low gravity reservoirs are relatively recent, geologically, the solid matrix material is usually soft and unconsolidated sand. Such formations are also characterized by a high clay content. Evaluation of sophisticated oil recovery processes with the associated high capital investments has increased the demand for special core analysis tests on material from these soft and unconsolidated sand reservoirs. Data in this paper have resulted from an extensive field and laboratory experimental program. The initial objective vras to provide soft and unconsolidated sand cores for laboratory measurements with as little alteration as possible from their reservoir condition. A secondary objective was to compare the waterflood behavior of these carefully preserved cores with measurements on the same cores after they had been extracted and resaturated. When the comparison showed markedly different behavior the final objective was to attempt to explain the difference by making measurements on idealized porous media free of clay in which initial wettability could be carefully controlled. EXPERIMENTS MATERIALS Core Material The preserved cores used in this study were obtained with as little alteration as possible from their reservoir conditions. Special techniques were developed to satisfy this objective. The cores were cut with native crude whenever the crude had the necessary properties to satisfy the minimum drilling fluid requirements. A pure hydrocarbon chromatographic tracer was added to the crude to provide a simple, safe and inexpensive method to distinguish between oil filtrate and formation oil. Details of the tracer technique used in this study and the procedures used to handle and process the soft, unconsolidated cores have been published.' The core samples were then preserved and packaged at the well site with a dip-applied strippable plastic, or by using a rubber sleeve from a rubber-sleeve core barrel. The final step was to insure that the carefully taken and preserved samples were not altered by processing in the laboratory. Some soft and poorly consolidated sands were carefully shaped in the lab and encased in a protective mounting without disturbing their three-dimensional integrity. Many samples were so poorly consolidated that they literally flowed from the package when the seal was broken. A technique was developed to obtain cylindrical plugs from these samples by using liquid nitrogen as the drilling fluid in a conventional core-drill, drill-press assembly. The idealized porous media consisted of sintered rods of Alundum RA 139, outcrop sandstone identified as Al-hambra sandstone and packs of No. 130 Nevada sand. This sand is 95 per cent 140-200 mesh. (Physical properties of these porous media with those representative of preserved cores are in Table 1.) The natural cores and most of the idealized porous media were 1 1/2-in. in diameter and 3-in. long. The samples used to study the effect of core length were 1 1/2-in. in diameter and 12-in. long. Liquids Water and oil produced from the formations being studied were protected from the atmosphere and collected in carefully cleaned glass or plastic-lined containers. The production was free of chemical additives such as emulsion breakers and corrosion inhibitors. The crude oil was

Jan 1, 1967

By C. C. Wright, T. S. Spicer, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation's fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944

By T. S. Spicer, C. C. Wright, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation's fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944

By THOMAS J. CLIFFORD

IN 1926, finer grinding began to be a feature of the milling practice of the Southeast Missouri lead district. Nothing since the adoption of flotation has caused greater changes and greater improvement in results. The trend toward finer grinding, with the consequent discarding of tailing at finer sizes, and consequent lower assays in lead, continued to progress until 1931, when the abnormally low price of lead brought a halt: that is, the better metallurgical results obtained would not offset the increased costs due to higher power and necessary maintenance. Since 1931 a slight tendency toward the discard of coarser tailing has taken place. , In 1926, larger rod mills i.12 ft. 1 in. by 6 ft. 6 in.) than any previously used in the district were installed in cue plant, and a new primary crushing plant, of greater capacity was built. This combination demonstrated immediately the better metallurgical results obtainable by finer grinding and all the mills now running have adopted the practice.

Jan 1, 1934

By J. Chipman, N. J. Grant, H. L. Bishop

Lime and dicalcium-silicate crucibles were equilibrated with molten iron and liquid slags containing iron oxide and small amounts of sulfur. The oxygen content of metal, iron oxide activities, and desulfurization values of the slags were determined in the temperature range 1530 to 1700°C. The influence of magnesia in the slag and the temperature dependence of the solubility of lime in liquid iron oxide and the ferric oxide content were established. The temperature contour of the liquidus surface of iron-silicate slags saturated with lime and dicalcium silicate was also established at 1600°C. THE importance of the role that slag composition plays in the refining of steel has been known for many years. Numerous studies have been made using actual plant data in order to establish the relationship between the composition of the slag and metal during the refining of a heat of liquid steel. These results rarely represent equilibrium conditions since completion of the various chemical reactions involved in steelmaking is seldom realized. In order to establish quantitatively the equilibrium conditions existing between the slag and metal, several laboratory studies have been conducted in the past 20 years to determine the reactions important in slag control. These investigations have included studies of simple liquid basic and acid slags as well as more complex slag systems which approach those commonly found during the refining of a heat of steel. Since most of the previous studies of simple basic iron-oxide slags equilibriated with molten iron were made in magnesia crucibles, it was not possible to establish the distribution of sulfur and oxygen between molten iron and slags consisting only of the three essential components, lime, silica, and iron oxide. This investigation was undertaken to establish the equilibrium conditions for simple lime-iron oxide and lime-silica-iron oxide slags. Accordingly, it was expedient to prepare crucibles both of lime and dicalcium silicate to establish the equilibrium conditions between molten iron and iron-oxide slags saturated with the refractory materials and free from other components. The only other studies of the equilibrium between molten iron and lime-saturated slags are those of Fischer and vom Ende, 1, 2 in which the solubility of oxygen was determined in an air atmosphere. The

Jan 1, 1959

By O. P. Dolph

SPANIARDS were probably the first to mine the rich surface ore in the veins cutting the rhyolite capping that outcrops on the hills of La Mazata, oil the Allyones side of the Magdalena valley in Jalisco, Mexico, although the name comes from a word of Indian origin meaning "deer". The camp is about 12 km. west of Magdalena, a town on the Southern Pacific Railroad, and about 17 km. north of Etzatlán, on the Mexican National Railroad, at an elevation of 4500 ft. The climate is subtropical with no extremes of heat or cold, the rainy season beginning in June and ending in October.

Jan 1, 1938

By Richard H. Rein, John Chipman

Liquid slags of the system SiO2-Ca0-MgO-A1~03 were equilibrated with liquid Fe-Si-C alloys in graphite or Sic crucibles at 1600°C in pure CO gas at atmospheric pressure, and the silicon content of both phases determined. Ternary slugs of the systern SiO2-CaO-A12O3 were also studied at 1550°C. The silicon content of the metal phase saturated with both graphite and SIC is 22.0pct at 1550°C and In the iron blast furnace, as in nearly all carbon-reduction processes, some silicon is transferred from slag to metal. The importance of this reaction is enhanced by its indirect effect on the transfer of sulfur from metal to slag, and this has stimulated a comprehensive research program on the equilibrium distribution of silicon between slag and metal. Earlier studies'-3 of this same problem provided data for calculation of the thermodynamic activities4 of the components in SiO,-CaO-A1,O3 slags. 22.4 pct at 1600°C. The temperature at which the phases cristobalite, gvaphite, $ SiC, liquid slag, Fe-Si-C alloy, and CO gas at 1 atm pressure can coexist in equilibrium was found to be 1533°C. The results agree well with earlier studies. They are shown graphically as lines of constant silicon cmtent in the metal which also are lines of constant SiO, activity in the slag.

Jan 1, 1963

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,400. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service. "It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. Robert Linton is chairman of the Charles F. Rand Foundation Award Committee.

Jan 1, 1943