Search Documents

By J. D. Rice, P. L. Wearden, W. L. Hensou

Solutions to the unsteady-state partial water-drive reservoir performance problem can be obtained through the use of analogue computers or high-speed electronic digital computers. The solutions that have previously been resolved for use on digital computers, however, demand a knowledge of the aquifer parameters. Generally, the analogue computers now in use do not require this knowledge. A solution is presented herein where the aquifer performance, expressed in terms of difference equations, is related to the reservoir performance as expressed by the modified Scbiltbuis material-balance equation. A numerical procedure for a medium-sized digital computer also is presented in which a solution to the set of equations defining the aquifer and reservoir performance is obtained and the aquifer parameters (permeability and sand thickness) are automatically optimized while simultaneously matching the known pressure behavior. Predicted pressure behavior can be calculated using rates from any assumed future production practice. The procedure provides an output format which presents the cumulative, incremental and average rate of natural water influx, the per cent gas-cap expansion, the calculated reservoir pressure, the measured reservoir pressure, and the difference between the measured and calculated pressures. Results of a test problem are presented in comparison with results obtained by the Bruce Analyzer, Ohio Oil Co. 's Pace General Purpose Analogue Computer, and Sun Oil Co.'s Single-Pool Electronic Reservoir Analyzer. These results indicate that unsteady-state reservoir perlormance for a single-pool system can be adequately simulated by a numerical method employing a digital computer and that the special-purpose analogue computer can be supplanted by this method. INTRODUCTION The numerical approach to the unsteady-state partial water-drive reservoir performance problem heretofore has been limited in that solutions have been resolved only for certain fixed parameters. Also, prior to the advent of high-speed electronic digital computers in the last few years, calculations were so tedious and time-consuming that they ordinarily were neglected, or some other means of obtaining the solutions were used. The analogue approach had been used for obtaining solutions to the transmission-of-heat problem and, consequently, means were developed for applying the electrical analogue to the unsteady-state reservoir performance problem. Bruce submitted a paper for AIME publication in Sept. 1942, in which he described an electronic device (now called the Bruce Analyzer) for analyzing the water-drive performance of any reservoir, based on either steady or unsteady-state flow characteristics. 1 Sun Oil Co. adopted the analogue approach in 1949 and now has two special-purpose high-speed electronic reservoir analyzers in use.2,3 Two main features of Sun's analyzers are (1) the high repetitive rate of reproducing the entire history of reservoir performance cyclically a number of times per second, and (2) the elimination of the necessity of knowing the properties of the associated aquifer. Since the advent of larger and faster digital computers, the possibility of incorporating this second feature into a numerical approach appeared feasible. Previous work has been done and material published covering the application of numerical methods to the behavior of the pressure with respect to time at any point in an associated aquifer? However, the aquifer parameters must be known from some source. The material presented in Ref. 4 has been used to a great degree in developing the numerical method described herein. DIFFERENTIAL EQUATION AND BOUNDARY CONDITIONS The problem of simulating the performance of a reservoir and the associated aquifer is to determine the characteristics of the aquifer such that the

By W. Bradley, R. G. Hall

This paper will attempt to show how a metallurgical problem at one California quicksilver mine was solved, and how the solution was applied successfully at another mine. The pronouns "we" and "our," as used below, refer '0 the Bradley 'lining Co. of San Francisco. The term "concurrent firing" for the purpose of this paper can be defined as feeding and firing a a kiln at the same end—that is, of course, the upper end' This is as opposed to "countercurrent firing," the orthodox method, in which a kiln is fed at the upper and fired at the lower end. The terms "quicksilver" and "mercury" are used interchangeably. Early References The earliest work on nonferrous metallurgy, we believe, was The Pirotechnia of Vannocio Biringuccio,l its first edition having been printed in Italy in 1540. Quoting from its chapter entitled "Concerning Quicksilver and Its Ore": Quicksilver ... is one of the gods and has divine strength in itself, and also, to the annoyance of the alchemists, it is winged. Hence, when it sees that it is in gravest danger, it loosens itself from . . . every bond . . . and fies away into the heavens, escaping from the hands of those who crucify it. Almost laughing, it leaves all its adversaries mocked and scorned, with their phials and filters empty . . . How thorough a job, under certain conditions, it can do of mocking its adversaries and leaving their phials and filters empty, was found out four centuries later at the Sulphur Bank mine, on the east shore of Clear Lake, in Lake county, California, The other mine mentioned in the title is the Reed, in Yolo County, California, 35 miles by road southeast of Sulphur Bank, Reed and Sulphur Bank ranked respectively Nth and seventh in U. S. production in 1943. The earliest direct reference we can find to furnacing troubles at these mines was by Thomas Egleston in 1890.2 Speaking of Sulphur Bank, Egleston says: of there is more sulphur than cinnabar in the ore, which is a detriment to both . . . making the sulphur impure, and rendering the cinnabar difficult to work on account of the soot. In some of the early . . . furnaces the accumulation of soot from the excess of sulphur has been known to penetrate as far as the fan blower at the end of the . . . condensers, and completely prevent its revolution. In order to get rid of the inconvenience of this accumulation . . . , as well as to get a commercial value from the sulphur, it (the sulphur) is now separated by steam and sold. It is claimed that the sulphur alone pays all the expenses of ... the mine. The mine was first worked for sulphur, and the cinnabar it contained was considered to be an inconvenience, and was carefully picked out and thrown away, as its richness and value were not

Jan 1, 1949

By William P. Blake

A recent paper by Prof. George P. Merrill, Curator of the Department of Geology of the U. S. National Museum, Wash-

Jan 1, 1897

By R. Wachtell

IN order to study better the phenomena at work in various phases of diffusion of the Fe/Si system when compounded and alloyed by powder metallurgy methods, several attacks have been planned. Electrical, hardness and other measurements have been discussed e1sewhere.l,2 The metallographic phenomena will be considered here. Concerning the metallography of the ferrosilicon alloys, some initial discussion is in order. As this laboratory discovered to its chagrin, there are many traps that lie in wait for even the experienced metal-lographer when he deals with alloys of high silicon content. Chief of these is probably the anomalous behavior of these materials under conventional etching techniques. We have before us, for instance, Corson's paper" of 1928, wherein is mentioned and illustrated (probably for the first time) the peculiar "barley shell" structure sometimes found in these alloys. Again in 19412 he same author reports the structure in 5-14 pct silicon irons. Houghton and Becker mention its presence' but make only tentative effort to explain it. In 1943, Hurst and Riley6 discussed the "barley shell" and declared it to be a false structure, resulting from the peculiar and characteristic film-forming propensities of the alloy. At about the same time, Wrazej7 proved correct the contentions of Hurst and Riley, establishing pretty well the mechanisms of formation and identifying the constituents involved. Hurst and Riley6 a1so describe in their paper (1943) a "cracked film" structure, also a pseudo-morph, the precise nature of which they do not suggest. Careful examination of such a film reveals that it not only cracks but begins to curl away from the surface of the metal and peel, much in the manner of flaking paint. The careful microscopist will be able to focus on the topmost edge of the flake, and, by optical sectioning, follow it down to the metal surface. We have been able, by oblique illumination of such specimens, to observe the raised segment of the film, the shadow that it casts, and the mating segment on the metal into which it fits. As late as 1946, Hurst and Riley8 found occasion to correct misinterpretation of this "cracked film" structure in a work by others on a 12 pct Si/Fe alloy. The "barley shell" and "cracked film" pseudo-morphs are not the only ones encountered in studies of these materials. A third pseudomorph, which may, however, have some structural significance is a fine striation of the surface. Closely spaced and parallel striae extend entirely across single grains. Each grain shows a different direction for the striae, and different closeness of the spacing. The regularity of this structure, and the fact that the striae do not cross from one grain to another, suggest that the structure is a film cracking controlled in some way by the crystal plane orientation of the surface being etched. In general it is wise for the metallographer dealing with these alloys to cultivate a feeling of uncertainty not only of the more complex questions of interpretation, but also of the basic question of whether that which he sees is indeed a true representation of the structure. We have taken, as a first test of the validity of a structure, its reproducibility "in situ" after repolishing and re-etching of the samples. Thus we knew the "barley shell" to be false (fig. 1) even before encountering the definitive works on the subject. The Metallography of Silicon Diffusion in Laminate Bars: As a first step in the study of the metallography of the diffusion process, we have pressed a series of laminate bars. These bars, or "sandwiches" as we have termed them, were pressed with covering layers of iron powder, and a "filler" of the Fe/Si master alloy under study. Bar dimensions were approximately %, x 3 x 1/4 in. The total

Jan 1, 1951

By J. L. Huitt, B. B. McGlothlin, D. K. Lowe

Published correlations for the principal aspects of hydraulic fracturing were combined into a digital computer program to facilitate the study of interrelated variables. The computer program includes individual relationships for fracture width during pumping, fracture area generated, propping agent embedment, flow capacities of propped fractures and transport of propping agents in horizontal fractures. The effects of more than 20 treatment and formation parameters on the predicted results of hydraulic fracturing treatments were studied. The effects of these parameters were determined for (I) fracture width during injection, (2) fracture width after the overburden comes to rest on the propping agents, assumed not to be crushed, (3) generated and propped fracture area, (4) location and concentration of propping agents in the fracture when injection ceases, (5) flow capacities of the various propped sections of the fracture and (6) expected increase in the well productivity. The effects of propping agent, formation and fracturing fluid parameters on well productivity are discussed. The parameters that were found to have the most pronounced effects on hydraulic fracturing treat~nents are injection rate, treatment volume, fracturing fluid coefficient, size and amount of propping agent, spearhead volume, well drainage radius and formation capacity. INTRODUCTION Many correlations have been published for predicting effects of various parameters that are considered in the design of hydraulic fracturing treatments. The Carter equation' can be used to predict generated fracture radius as a function of fracture width, fracturing fluid leakoff and other parameters. Fracture width can be determined by use of the Perkins and Kern correlation' in which the fracture width is related to the fracture radius, fluid injection rate and certain formation and fracturing fluid parameters. Wahl and Lowe et aL4 have reported methods of predicting the location of propping agents in fractures when pumping ceases. The former study is applicable to the case where the ratio of propping agent diameter to fracture width is less than 0.1. The latter is applicable when this ratio is greater than 0.1. These studies showed that the propping agent placement in horizontal-radial fractures depends principally on how the individual particles are transported in the fracture by the carrying fluid. Particle transport in fractures is determined by local fluid velocity in the fracture, fluid and particle properties, and the size of the particle relative to the fracture width. The distribution of propping agents, effective overburden pressure and formation rock strength control the propped fracture width6 by controlling the extent to which the propping agent particles embed into the fracture faces. From the distribution of propping agents and the propped fracture width, fracture flow capacities can be calculated or the various regions of the fracture. The flow capacities and the radial extent of these regions can be combined with reservoir information to predict the productivity increases for fractured wells. In all these studies, the effects of certain treatment and/ or reservoir parameters on one facet of fracturing can be predicted only if other facets which the parameters affect are fixed. For instance, fracture width and radius are interrelated; that is, to calculate the value of one, the value of the other must be known. Also, some parameters influence more than one aspect of fracturing. For example, prop-pant transport is a function of both fracture width and fluid viscosity. but fracture width is itself a function of fluid viscosity. Since these calculations are complex and the parameters interrelated, it is not possible to write an equation with which the over-all effects of treatment parameters can be solved explicitly. For these reasons, the correlations for determining the effects of the parameters which are most significant in hydraulic fracturing treatments have been incorporated into a digital computer program. COMPUTER PROGRAM The program, which was written for an IBM 7094 computer, can be used to predict results of most of the combinations and values for the treatment parameters that are ordinarily considered for fracturing treatments. A spearhead of fracturing fluid and a propping agent-carrying fluid with different fluid properties can be taken into account. Also, the total volumes and relative amounts of the spearhead and carrying fluids can be varied. Two different propping agents (as used in tail-in operations) and a wide range of formation properties and injection rates are considered. The computer program (Fig. 12) consists of several sets of calculations. First, the final flooded fracture radius and average fracture width at the cessation of pumping are calculated. This is done by simultaneous solution of the Perkins and Kern fracture width equation and the Carter equation for flooded fracture radius (equations used in the computer program appear in the Appendix). The next step is to determine local fluid velocity in the fracture as a function of time and radius. Since it is not possible to write this function in closed form expression, a table of velocity values is generated by the program and stored for subsequent use. The time span from the beginning of

By Herbert Clark Hoover, Lou Henry Hoover

DIFFERENT methods of parting gold from silver, and, on the other hand, silver from gold, were discussed in the last book; also the separation of copper from the latter and further, of lead from gold as well as from silver ; and, lastly, the methods for refining the two precious metals. Now I will speak of the methods by which silver must be separated from copper, and likewise from iron.1 The officina, or the building necessary for the purposes and use of those who separate silver from copper, is constructed in this manner. First, four long walls are built, of which the first, which is parallel with the bank of a stream, and the second, are both two hundred and sixty-four feet long. The second, however, stops at one hundred and fifty-one feet, and after, as it were, a break for a length of twenty-four feet, it continues again until it is of a length equal to the first wall. The third wall is one hundred and twenty feet long, starting at a point opposite the sixty-seventh foot of the other walls, and reaching to their one hundred and eighty-sixth foot.

Jan 1, 1950

By R. H. Landshof, Reynold Q. Shotts, James A. Redding

GENERAL INTRODUCTION by R. Q. Shotts The sizing of coal particles is one of the most important beneficiation operations performed from the time coal is broken at the face until it is delivered to the customer. Indeed, in many cases it may be virtually the only such operation performed in that interval, although it is most often accompanied by some comminution. Sizing, as the term implies, is a separation of the broken coal particles into arbitrary groups, each group containing particles within restricted mass, volume or size limits. Size itself is not a rigidly defined property, but is actually determined more by the operating principles of the sizing device than by unique properties of the particles themselves. Particle size cannot be uniquely defined independently of particle shape. Taggart l says, "In fact, it is not possible to state the size of a single irregular body by means of a single dimension; such possibility exists only for regular polyhedra and their limit, the sphere." In view of the scarcity of regular polyhedra among coal particles, even though most appear to approximate a cube, we actually define size in terms of a surface opening through which the particle barely will or will not pass, or of two openings, the smaller of which retains all particles of the group under study and the larger of which passes all of them. Alternatively, size is expressed in terms of rate of settling of particles in a fluid under closely controlled conditions. Historical Sketch2-Taken from Coal Preparation, 2nd Ed. "Sizing is the process of separating mixed particles into groups of particles all of the same size or into groups in which all particles range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. "In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes in the mine working places to recover coarse coal. The mining procedure left the fines in the mine.

Jan 1, 1968

By Frances Jane Cromwell, D. J. McAdam, G. W. Geil

INTRODUCTION IN a series of papers, the authors and their associates have shown that the technical cohesion limit is affected by the same four factors that affect the flow stress, namely, the stress system, plastic deformation, temperature, and the strain rate.16-28 Moreover, each of these factors affects the technical cohesion limit in the same way that it affects the flow stress.‡ The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into use with the same significance as "technical cohesion limit," the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. This paper presents the results of an investigation of the flow of notched and unnotched specimens between yield and fracture. A study has thus been made of the flow and fracture of metals as affected by the stress system, and of the ductility of metals as affected by the stress system throughout plastic deformation. Since two of the principal stresses were equal (S2 = S3), the stress systems can be represented in terms of the radial stress ratio, the ratio of the transverse radial stress S3 to the longitudinal stress Sl.* The results of the experiments are represented by a series of complete flow-stress curves for each of the metals investigated, and these diagrams have been used for the development of other diagrams of various types. Ludwik was the first to suggest that fracture occurs when the flow stress becomes equal to a technical cohesion limit. Although Ludwik was incorrect in his view that the technical cohesion limit depends only on the amount of plastic deformation and not on the stress system, he was correct in his view that the flow-stress curve for any stress system terminates at a point representing a technical cohesion limit. The authors have seen some recent references to assertions by other investigators that a point representing the fracture stress need not be on the flow-stress curve. The Ludwik principle, however, would seem to be axiomatic, provided that the flow stress and fracture stress are properly defined and that the fracture stress is properly determined. Disregard of this principle has led to some untenable theories of criteria for fracture. When a metal is very ductile, the conventional method of determining the ductility and fracture stress by dividing the breaking load by the sectional area after fracture, generally gives values that are much too high. With some metals and in some conditions, the fracture stress thus determined may be two or more times the

Jan 1, 1948

By J. B. Austin

IN considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based . upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these effi-ciencies are more useful than others, yet all are instructive; for a knowl-edge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermo-dynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By Henry D. Hibbard

FoR the purpose of this paper all steels will be divided into two divisions: effervescing and non-effervescing. This classification must be borne in mind as many statements true of one class are not true of the other. Effervescing steels are those that effervesce in the molds, evolving large volumes of gases, which, in escaping, throw up a spray of molten particles of steel and give the molten metal in the mold a rapid stirring or churning motion until it freezes, or, at least, becomes pasty. This effervescing is intended and proper. The non-effervescing steels, which are more or less completely killed, should not evolve any gas in the molds. Many years ago the writer proposed to call the two classes of steels evolution and solution steels, depending on whether the gases in the molds are evolved or kept in solution, but the present designations seem to be better. In America, at least, effervescing steels are in a class by themselves and include steels made for boiler, tank, and ship plates, steel pipe, soft steel wire, wire nails, soft machincry, and structural steels. These are all low-carbon steels with less than 0.40 per cent. carbon. Low-carbon steels that do not effervesce but are killed are also made; these are put into ingots and castings but they are outside the limits of this paper. Effervescing steel is cast into square or slab molds, either top or bottom poured. Most of the effervescing steel is made in the basic open-hearth furnace, though much is made by the acid Bessemer process and a little is made in the acid open-hearth. It is not made by the crucible or electric-furnace process, in which the volume of gas required cannot be produced in the steel and evolved from it in the mold to give the effervescence desired. Any steel ingot, when teeming is finished, is of a certain size or volume. Leaving out of consideration for the moment the lessening of the over-all dimensions of the ingot through contraction due to loss of heat, the ingot may be placed in one of three classes: It may settle, losing in volume; it may stand, that is, remain constant in volume; it may rise, that is, increase in volume. Into which class an ingot will fall depends on the gases of the steel,

Jan 1, 1920

By E. DeGolyer

I. INTRODUCTION VOLCANIC origin. was among the first of the theories advanced to account for the occurrence of the salt domes of the Gulf coastal plain, northern Louisiana., and eastern Texas, and it is still being re-stated in various forms by the most recent contributors to our knowledge of the geology of such deposits. Argument has been largely by analogy and attention has repeatedly been called to the Mexican oil fields, particularly those of the Tampico-Tuxpam region, because of the occurrence of oil in close proximity to volcanic plugs in those fields, an occurrence supposed to have some resemblance to the common occurrence of oil in the salt domes of the United States. The author, having spent several months of the past year in a general study of salt domes and in a detailed study of certain domes in the United States, and having been acquainted for some time with the exploration of similar domes in the Isthmus of Tehuantepec region, Mexico, and with the general geology of the Tampico-Tuxpam region, Mexico, has reviewed the various theories of volcanic origin for salt domes which have been advanced to the present time. The purpose of this paper is to present such review and to discuss the supposed Mexican analogy.

Jan 5, 1918

By Julian E. Tobey

A MEMORABLE year has just passed in the field of coal utilization. Because of the war, oil conversions in industrial, commercial, and domestic installations have been made to the equivalent of 20,000,000 tons of coal. The war emergency has resulted in a great shifting of various types of coals to various markets. Huge tonnages of metallurgical-quality coals have been withdrawn from steam and domestic business and sent into the iron and steel industries. Marginal coals have replaced these coals in the steam and domestic field.

Jan 1, 1944

By Hugh S. Spence

IN the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mattawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were 'found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by Inspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the summer of 1942 to inspect the property,

Jan 1, 1947

By J. W. Furness

Before attempting any discussion of the importance of tariff enactments as applied to exhaustible resources, certain basic factors should be emphasized. First, it must be remembered that minerals differ from organic substances in that they are irreplaceable, and when once taken from the earth's crust enter into uses which ultimately dissipate them, so . that they cannot be recovered for future use. A second factor entering into the problem is the unequal distribution of the mineral deposits of the world. No industrial nation has within its political confines a sufficient quantity of all the minerals necessary for the maintenance and advancement of present civilization; hence international exchange of these commodities is inevitable. As minerals are essential to modern industry, the supply available to any given nation constitutes a factor which limits its ambition to advance industrially. A nation which has this ambition endeavors to secure not only a supply of minerals sufficient for its current needs, but also sources which will assure it expansion. Should mineral raw materials be withheld from such a nation by enactment, it seems inevitable that every effort will be made to obtain them, and that, should the nation deem itself sufficiently powerful, its ultimate recourse will be force. Thus the importance of tariff enactments, not only from the standpoint of industrial prosperity but from the standpoint of international peace, can be appreciated.

Jan 1, 1932

By R. S. French

THE purpose of this paper is to present data that have been obtained during the past two years concerning the effects of prior cold-work and temperature and time of anneal upon the recrystallization and grain growth of 70-30 cartridge brass. It was desirable to study certain of these phases so that an accurate picture of the principles of the subject could be shown. The work is not intended to provide explicit annealing data, but to provide material examples that may help to clarify analogous problems concerning this alloy. Specifications often set limitations upon the grain size of annealed materials because of the importance of grain size upon subsequent manufacturing operations. It was, therefore, worth while to study the variables that affect the recrystallized grain size of this material. C. H. Mathewson and A. Phillips,1 W. R. Webster,2 and others have presented annealing characteristic curves of this alloy. A recent typical curve presented by R. S. Pratt3 is shown in Fig. I. The tensile properties and grain sizes are shown as functions of the annealing temperature. Such curves serve as a useful guide in determining the physical properties of annealed material, but as they are made generally under carefully controlled laboratory conditions they do not indicate the performance of metal annealed in a mill muffle, where conditions are different and the amounts of metal require necessarily longer heating times and temperatures. Study of the effect of time and temperature upon grain growth and subsequent recrystallization was made with a coil of metal having the following analysis: 70.04 per cent copper; 0.007 lead; 0.007 iron; 0.00 tin; 0.00 silicon; 0.001 nickel; 0.000 phosphorus; balance zinc. The sample coil was obtained from metal that had been rerolled from hot-rolled mill stock, and was received at 0.228-in. gauge, soft, with a grain size of 0.125 mm. This material was then rolled 43.5 per cent to 0.125-in. gauge and annealed to a 0.053-mm. grain size. In this condition, samples were cut and used in all of the experimental work reported in this paper. TIME The first study was of crystal growth at a constant temperature over a moderate length of time. Material was cut from the stock coil at 0.129-in. size and rolled 75 per cent hard to 0.032-in. gauge. From this piece small samples were cut ½ by 2 in., suitable for grain-size determinations. Twelve samples were placed in an electric furnace uniformly across the width, approximately an inch from the floor, A thermocouple was wired to the center sample, so that the approximate metal temperature could be followed. At various

Jan 1, 1944

By R. S. French

The purpose of this paper is to present data that have been obtained during the past two years concerning the effects of prior cold-work and temperature and time of anneal upon the recrystallization and grain growth of 70-30 cartridge brass. It was desirable to study certain of these phases so that an accurate picture of the principles of the subject could be shown. The work is not intended to provide explicit annealing data, but to provide material examples that may help to clarify analogous problems concerning this alloy. Specifications often set limitations upon the grain size of annealed materials because of the importance of grain size upon subsequent manufacturing operations. It was, therefore, worth while to study the variables that affect the recrystallized grain size of this material. C. H. Mathewson and A. Phillips,l W. R, Webster,2 and others have presented annealing characteristic curves of this alloy. A recent typical curve presented by R. S. Pratt3 is shown in Fig. I. The tensile properties and grain sizes are shown as functions of the annealing temperature. Such curves serve as a useful guide in determining the physical properties of annealed material, but as they are made generally under carefully controlled laboratory conditions they do not indicate the performance of metal annealed in a mill muffle, where such conditions as amounts of metal, heating time and temperature may differ. Study of the effect of time and temperature upon grain growth and subscquent recrystallization was made with a coil of metal having the following analysis: 70.04 per cent copper; 0.007 lead; 0.007 iron; 0.00 tin; 0.00 silicon; 0.001 nickel; 0.000 phosphorus; balance zinc. The sample coil was obtained from metal that had been rerolled from hot-rolled mill stock, and was received at 0.228-in. gauge, soft, with a grain size of 0.125 mm. This material was then rolled 43.5 per cent to 0.129-in. gauge and annealed to a 0.053-mm. grain size. In this condition, samples were cut and used in all of the experimental work reported in this paper. Time The first study was of crystal growth at a constant temperature over a moderate length of time. Material was cut from the stock coil at 0.129-in. size and rolled 75 per , cent hard to 0.032-in. gauge. From this piece small samples were cut M by 2 in., suitable for grain-size determina.tions. Twelve samples were placed in an electric furnace uniformly across the width, approximately an inch from the floor. A thermocouple was wired to the center sample, so that the approximate metal temperature could be followed. At various

Jan 1, 1944

By R. S. French

The purpose of this paper is to present data that have been obtained during the past two years concerning the effects of prior cold-work and temperature and time of anneal upon the recrystallization and grain growth of 70-30 cartridge brass. It was desirable to study certain of these phases so that an accurate picture of the principles of the subject could be shown. The work is not intended to provide explicit annealing data, but to provide material examples that may help to clarify analogous problems concerning this alloy. Specifications often set limitations upon the grain size of annealed materials because of the importance of grain size upon subsequent manufacturing operations. It was, therefore, worth while to study the variables that affect the recrystallized grain size of this material. C. H. Mathewson and A. Phillips,l W. R, Webster,2 and others have presented annealing characteristic curves of this alloy. A recent typical curve presented by R. S. Pratt3 is shown in Fig. I. The tensile properties and grain sizes are shown as functions of the annealing temperature. Such curves serve as a useful guide in determining the physical properties of annealed material, but as they are made generally under carefully controlled laboratory conditions they do not indicate the performance of metal annealed in a mill muffle, where such conditions as amounts of metal, heating time and temperature may differ. Study of the effect of time and temperature upon grain growth and subscquent recrystallization was made with a coil of metal having the following analysis: 70.04 per cent copper; 0.007 lead; 0.007 iron; 0.00 tin; 0.00 silicon; 0.001 nickel; 0.000 phosphorus; balance zinc. The sample coil was obtained from metal that had been rerolled from hot-rolled mill stock, and was received at 0.228-in. gauge, soft, with a grain size of 0.125 mm. This material was then rolled 43.5 per cent to 0.129-in. gauge and annealed to a 0.053-mm. grain size. In this condition, samples were cut and used in all of the experimental work reported in this paper. Time The first study was of crystal growth at a constant temperature over a moderate length of time. Material was cut from the stock coil at 0.129-in. size and rolled 75 per , cent hard to 0.032-in. gauge. From this piece small samples were cut M by 2 in., suitable for grain-size determina.tions. Twelve samples were placed in an electric furnace uniformly across the width, approximately an inch from the floor. A thermocouple was wired to the center sample, so that the approximate metal temperature could be followed. At various

Jan 1, 1944

By Nelson P. Hulst

To those who have had the happy privilege of friendship with George W. Goetz, the announcement of his death has brought great sadness. He was born in Milwaukee, Wisconsin, February 17, 1855, and died January 15, 1897. In his boyhood days, when I first came to know him, his frank, trustful manner; his eyes brimming with truthfulness; his eagerness, never obtrusive, to gain knowledge from all whom he met; and his equal readiness to give without ostentation of his store, constituted a personality which at once commanded confidence and won friendship. I am told that as a scholar of five years he was conspicuous for brightness, a show-pupil, who was called on to recite when visitors were present at school. Yet this in no way spoiled him. His modesty was too strong a trait in his character to be overcome by any attention which might, be expected to arouse vanity. In his simple-heartedness he was pleased then, as he always was in his maturer years, to give of his knowledge for the gratification of his listeners, with never a thought of himself. So strong was this characteristic that in a brief autobiography, in the form of a letter to his wife and children, found among his papers, he excuses himself to them for recounting what he had accomplished in his life-work. As a preface to this autobiography (which, it seems, was prepared on the eve of a sudden journey to California, taken February, 1895, for his health) he says: " I am writing this rather hastily, and I

Jan 1, 1898