Search Documents

By Homer G. Turner

Coals, other than anthracite, have been so thoroughly studied under the microscope during recent years, that we now know what kinds of plants and what parts of plants form the bulk of lower rank coals from peat to bituminous coal. The microscope has also shown the state of preservation of such vegetation as well as the nature and distribution of products of plant decay. These and further details have been ascertained mainly through the employment of two methods of attack, section cutting and maceration. Anthracite has failed to respond to these methods, so well adapted to the study of lower rank coals and, therefore, has been neglected by investigators to such an extent that there is much doubt as to its microscopical characteristics. The object of this paper is to lift anthracite from its realm of obscurity by demonstrating the wealth of microscopical detail that is revealed when reflected light is used on a properly polished and etched surface and, further, to show the relationship between anthracite and bituminous coal. Technique The method adopted in this investigation is similar to that described in an earlier paper.' Because of slight modifications recently made, the process is again described. It consists, briefly, of etching a polished surface of coal with heat. Although pieces of various sizes and shapes are used, blocks of coal about 2 or 3 cm. square take the most uniform polish and are large enough to be handled with ease. Larger pieces can be used if one has the equipment for polishing them and they rnay be desirable when one wishes to study some particular form that extends for some distance through the coal. Large surfaces, however, require greater care in polishing and etching; for this reason, they are not recommended for ordinary work.

Jan 1, 1925

By HUBERT O. De

IN December, 1936, several drilling tests were made at the Hubert O. De Beck feldspar mine at Green Mountain, N. C., to determine the most efficient type of hammier-drill bit and drilling method for use at this particular property. This mine is well recognized as having the hardest rock in the Burnsville - Spruce Pine feldspar district and drilling costs always have been high. Local structural deformation has greatly distorted and warped the normal crystalline structure of the feldspar so the rock is much tougher than usual. In studying drilling methods and bit types, available literature was re¬viewed but little specific data could be found on the direct comparison of four-point and six-point drill bits so the following results may be of some interest.

Jan 1, 1937

By Ulrich H. Roesler

RECENTLY, C. Zener1 published a new thermo-dynamic treatment of the a/y transformation in iron alloys. His interpretation differs from the previous theories2-0 ainly through the separation of the free energy difference, Ga—G, into two additive

Jan 1, 1957

By Claus Guenter Goetzeil

(New York Meeting, February, 1937) The object of this investigation was to determine whether silver alloys could be used instead of the currently employed insert of high-expansion Average Coefficient per Deg. C. over Range 20° to 200° C. Pure aluminum..................................... 24.6 X 10-6 Cast low-expansion Si-Cu-Ni-A1 piston alloy............ 20.0 X 10-6 High-expansion austenitic Cu-Ni cast iron.............. 19.3 X 10-6 Cast steel (0.25-0.35 C, 0.40-1.0 Mn).................. 12.6 X 10-6 Cast iron (3.15 total C, 2.16 Si)....................... 12.8 X 10-6 Pure silver.......................................... 18.9 X 10-6 austenitic ferronickel alloy, to reduce the wear of ring grooves in light metal pistons. A typical example of a piston containing a ferronickel insert is shown in Fig. 1. The high coefficient of expansion of silver made it worthy of consideration, while the small size of the insert would render its use feasible in Germany as an emergency measure. The coefficients of linear expansion of several metals and ailoys are as shown in the table above. Obviously the melting point of the insert must be high enough to prevent it from melting when the light alloy is cast around it. This imposes a lower limit of about 850" C. for the solidus of the silver alloy. Pure silver melts at about 961" C., so that the tolerable depression in the solidus is rather small. To avoid deformation of the insert during use a Brinell hardness number of at least 60 appears necessary.

Jan 1, 1937

By R. J. McNally

THERE are three primary plant nutrients—nitrogen, phosphorus, and potassium—expressed in any fertilizer compound as percent N, percent P 2 O 5, and percent K 2 O, in that order. This article will be concerned with the first two. The chief source of P 2 O 5 is phosphate rock. As found in the western states phosphate rock is essentially tricalcium phosphate-calcium fluoride (fluor-patite). As such, it is quite water insoluble.

Jan 1, 1957

By H. F. Gossenberger, J. J. Tietjen, J. J. Gannon, C. J. Nuese

External quantum efficiency measurements at 300" and 77°K are presented for vapor-grown GaAs and GaAs1-xPx electroluminescent diodes as a function of junction depth and doping. In GaAs, external efficiencies are found to decrease exponentially with increasing junction depth, defining an average absorption coefficient of 900 cm-1 at 300°K and 350 cm-1 at 77°Kfor epitaxial layers of p-type GaAs. It is shown that photon absorption losses dominate at room temperature and, in fact, account for most of the external efficiency degradation between 77° and 300°K. Healever, the internal ('junction) quantum efficiency is also found to decrease by a factor of 3.5 between 77" ALTHOUGH rapid progress has been made in recent years with GaAs, Gap, and their alloys for use in electroluminescent diodes, there are still important unknown factors related to the performance of these de- and 300°K. The dependence of GaAs efficiencies on donor and acceptor concentrations is presented, illustrating best efficiencies at donor concentrations of 1.5 to 2x 1018 cm-3 . External efficiencies are found to be independent of acceptor concentrations less than 3 x 1019 cm-3 but to degrade at higher doping. The fabrication of GaAsi-xPx electroluminescent diodes is briefly discussed. External efficiencies here for planar uncoated diodes are about 0.035 pct at 300°K and 0.4 pct at 77°for x = 0.42. A brightness of about 8500 ft-Lamberts is attained at 77°K and of 315 ft-Lamberts at 300° K. for curvent densities of 10 amp per sq cm. vices. For example, although the external efficiency is known to decrease by factors of typically 10 to 30 between 77°K and room temperature, the exact causes of this are still uncertain. Experimental results of ill' and carr2 with zinc-diffused electroluminescent diodes suggest that this external degradation is almost entirely due to increased absorption losses at room temperature, with a relatively temperature-independent internal efficiency; recent calculations by Gonda et al.3 corroborate this hypothesis. In contrast, Pilkuhn and Rupprecht4 find the internal efficiency of solution-grown GaAs laser diodes to degrade from 100 to 66 to 40 pct as the temperature is increased from

Jan 1, 1969

By Milton E. Wadsworth, W. Martin Fassell, William H. Dresher

A study of the rate of dissolution of molybdenite (MoS2) in alkaline solution was carried out under carefully controlled conditions. Effects of temperature, oxygen over-pressure, and KOH concentration were evaluated. Studies were made in the temperature range 100°C to 175°C and in the pressure range 0 to 700 psia of oxygen. Under these conditions molybdenite was found to leach according to a linear mechanism. Both oxygen over-pressure and KOH concentration were found to control the rate of leaching. The mechanism has been explained in terms of adsorption of oxygen at the molybdenite surface followed by configurational rearrangement of the adsorbed molecules. The hydroxyl ion dependency is believed to be diffusion-controlled. Laboratory batch studies have shown that molybdenite can be readily dissolved in alkaline solutions under moderate conditions of temperature and pressure. Commercial application of this process to the production of ferro-molybdenum and molybdenum chemicals is promising in view of the ease of dissolution of molybdenite and the relatively noncorrosive conditions involved in the process. HIGH temperature-high pressure techniques have long been used to great advantage in the organic chemical industry, the petroleum industry, and the paper industry. Only recently, however, have these methods been used to extract metals from their ores on a commercial scale. The Chemical Construction Corp., together with interested producers of nickel and cobalt, has done much to develop methods of producing nickel and cobalt powders by the use of high temperature-high pressure techniques.' The Howe Sound Co. is currently operating a plant near Salt Lake City in which the new Chemical Construction Corp. technique is applied to cobalt-arsenic sulfide concentrates. In this method the concentrates are leached in a dilute solution of sulfuric acid under air pressure at a high temperature. Near Edmonton, in Alberta, Canada, the Sherritt Gordon Co. is also using the new method in conjunction with its ammoniacal leach process.' National Lead Co., at Fredricktown, Mo., is operating a process similar to that of Howe Sound. In spite of the rapid growth of high temperature-high pressure hydrometallurgical processes, there has been very little work done on fundamental principles involved in this type of process. Conse- quently the literature lacks any significant data in this field. Oxidation of pyrite,3 phalerite,4 galena,5 and recently molybdenite" in alkaline solutions has been reported to some extent. This investigation was initiated, therefore, to broaden the application of high temperature-high pressure hydrometallurgy and also to contribute some insight into the basic mechanisms of oxidation in an aqueous medium under these conditions. In addition to the immediate consequences of these processes much valuable information remains to be learned about fundamental reactions when they are carried out at temperatures and pressures slightly higher than those normally encountered. Leaching of molybdenite by alkaline solutions under oxygen pressure has recently been reported in the Russian literature by E. S. Usataya,8 who found that leaching rate increased with an increase in the pH of the solution—the strongest effects being observed at a pH of 10—and also with an increase in temperature. Usataya also has reported the formation of a protective film on the surface of the molybdenite when the leaching solution was weakly alkaline, neutral, or acidic. He believes that this oxidation process explains the migration of Mo+ + in the oxidation zones of molybdenite ore deposits and the subsequent impoverishment of the ores. Equipment: The high temperature-high pressure reaction unit used in this work was especially designed for kinetic studies of this nature, emphasis being placed on accuracy of measurement and precision of control. As details of the unit's construction and operation have been discussed elsewhere,7 Only basic features and principles of operation will be discussed at this point.

Jan 1, 1957

By G. Baralis, P. Gondi, I. Tangerini, G. Scandola

The precipitation behavior of Zn-0.5 pct A1 alloy single crystals was studied by means of electrical resistivity measurements and by optical and electron microscopy. The single crystals for the resistivity measurements were prepared by an original method in - 100-p -thick sheets. The order of the precipitation kinetics ranged between 1 and 1.5. The dislocations play a relevant role in the first-order kinetics. Precipitation always occurs both on dispersed particles and on dislocations. Statistical examinations have shown that the first-order kinetics can have two different activation energies; i.e., the precipitation can have dz;fferent mechanisnrs which could not be identified, however, in the course of the research. During the tnetallographic exanzination of the precipitation structures a specific process of dislocation decoration was obsereed. The main purpose of this work was to study the contribution of dislocations to the precipitation. A number of authors have observed precipitation on dislocations and reference might be made to several monographs on the ubject.'' The possibility that dislocations also accelerate precipitation has been considered by Turn-bull3 and Fischer et al.4 The studies described in the present paper were carried out on zinc, chosen as a base metal owing to the ease with which dislocations can be introduced into it and because of the absence of excess vacancies after quenching in conditions where phenomena of accelerated precipitation still occur. Aluminum was preferred as alloying element because of the accelerated precipitation phenomena that resulted in a preliminary reearch. EXPERIMENTAL METHODS The observations refer to a Zn-0.5 pct A1 alloy. The zinc was 99.995 pct pure; a typical spectroscopical analysis is given in Table I. As a rule the alloy was subjected to homogenization, quenching, or slow cooling and annealing. Homogenization was carried out by heating at 390" to 410°C for 24 hr. From the homogenization temperature, some specimens were quenched and some slowly cooled at a rate of 2°C per sec. At this rate no precipitate was detectable under the optical microscope just after cooling. Quenching was carried out simply by dropping the specimens into water, aqueous ethylene glycol solution at -30" c, or liquid-nitrogen baths placed close to the homogenization oven. Vaseline oil baths were used with a thermal stabilization of 10-20 for both the aging treatments and the measurements; aging was generally carried out at 90" or 130°C. To avoid oxidation phenomena during heating, the vaseline oil baths had to be frequently renewed. The precipitation kinetics were studied by means of electrical resistivity measurements, using ans potentiometric method (reproducibility ± 5 x 10 5 v, that is 0.5 pct of the total voltage decreases on the specimens during precipitation). First, various types of specimens were tested, i.e., polycrystals, single crystals grown in capillary quartz tubes, and thin single-crystal sheets prepared by means of an original method requiring no container except for the natural oxide. Even if fully annealed, the polycrystals and the capillary grown single crystals showed resistivity in -creases, most probably due to dislocations introduced in the course of the measurements. Similar resistivity increases in pure zinc were noticed by another author. Only the single-crystal sheets showed no resistivity change; thus they were chosen for the subsequent tests. As already mentioned, these single crystals were obtained by using, as a container, the natural oxide on the zinc surface; the oxide strength is sufficient to maintain the original shape during melting with sheets up to 500 p thick. An initial zone melting and subsequent zone leveling, which led also to formation of the single crystals, were thus carried out on rolled sheets of the required thicknesses (- 100 p) and shape, lying on a flat silica surface. The resistivities were first evaluated by measurements at the liquid-nitrogen temperature. This method gave poor reproducibility, however, and this was attributed to the thermal cycles which had to be operated. To avoid cycles and handling, it was therefore decided to make measurements directly in the annealing oil baths; this required thermal stabilization at ilo-' "C. In this way only the resistance changes were measured. Specimens of pure zinc and of completely annealed alloy were always examined as controls together with those under consideration; only those measurement runs were taken into account where the reference samples showed no resistance increases. Again, the main inconvenience was due to oxidation and this was avoided by renewing the oil baths; even so data reproducibility was poor and the observations were therefore carried out on a large number (many hundreds) of specimens so as to provide indications of statistical value. For the transmission observations under the elec-

Jan 1, 1969

By Richard J. Borg

The vapor pressure of Cd in equilibrium with CdSb in the presence of excess Sb has been measured using the Knudsen effusion method over the temperature range 276° to 379°C. The free energy of formation of CdSb is given by AF° = -1.58 + 1.53 x l0-4 T, kcal per mole. The enthalpy and entropy are obtained from the temperature coefficient of the .free energy. CADMIUM and antimony have almost imperceptible mutual solid solubility but form a single stable intermediate phase, CdSb. This phase, according to Han-sen,l extends from about 49.5 at. pct to 50 at. pct Cd at 300°C and has the orthorhombic structure. The free energy of formation of CdSb can be calculated from the vapor pressure of Cd for compositions which contain less than 49 at. pct Cd. The appropriate reaction and formulae are given by Eqs. [I] and [2]- CdSb(s, ~ Cd(g)-, +Sb(s) [1] Since Sb is in its standard state, Af - N,,AF'-,, = NcdRT In a,, = NcdRT InP/PO [2] In Eq. [2], P, is the vapor pressure of Cd in equilibrium with the alloy, and Po is the vapor pressure in equilibrium with pure solid Cd. It is implicit in this calculation that the free energy only slightly changes within the narrow limits of the single phase field. Thus, the value obtained from the antimony-rich boundary is truly representative of the stoi-chiometric compound. The results reported herein are obtained from a mixture near the eutectic composition, i.e. 59 at. pct Sb. Only two previous investigations" of the free energy of formation of CdSb have been made. Both relied upon the electromotive force method, and measurements were made over relatively narrow temperature ranges which strongly influences the reliability of the values of AH and aS. EXPERIMENTAL The eutectic composition is prepared by fusing reagent grade Cd and Sb by induction heating in vacuo with the starting materials held in a graphite crucible having a threaded lid. The material obtained from the initial melt is pulverized, sealed under high vacuum in a pyrex capsule, and annealed at 420°C for two weeks. X-ray analysis"gives the following lattize parameters: a = 6.436A, b = 8.230& and c = 8.498A using Cu Ka radiation with A = 1.54056. These values are in fair agreement with the result? previously reported by Al~in:4 i.e. a = 6.471A, b = 8.253A, and c = 8.526A. Vapor pressures are measured using an apparatus which has been described elsewhere,= however, with a single important modification. Knudsen effusion cells are made of pyrex with knife-edged orifices made by grinding the convex surface of the lid on #600 emery paper. Photographs taken at known magnifications using a Leitz metallograph enable the determination of the orifice area. Numerous calibration measurements of the vapor pressure of pure Cd give close agreement with values previously reported5,= thus indicating that no significant error can be ascribed to the substitution of glass cells for metal cells used in previous work. Because the vapor pressure of Cd is reliably established and because it is difficult to obtain Clausing factors for the glass cells, the final values used for the orifice areas are calculated from the calibration measurements of the vapor pressure of pure Cd. Effusion runs are started in an atmosphere of purified helium which is quickly evacuated as soon as the cell attains thermal equilibrium. Less than one minute is necessary to obtain high vacuum after evacuation begins, and the temperature seldom varies by more than 0.5oC from the value obtained prior to pumping out the helium. RESULTS The results of this investigation along with other pertinent data are tabulated in Table I. Fig. 2 is the familiar graph of log P against T-10 K. At least mean squares analysis of the data presented in Table I yields the following equation: log1DJP = 8.790 - 6472 x T"1 [3] The deviations of the individual measurements from the values calculated with Eq. 131 are given in column six of Table I; the average deviation is 4.0% of the calculated value. Although the partial molal properties change significantly with composition within the single phase region, the integral thermodynamic value should remain relatively constant. Hence the results of the following calculations, which use the data obtained for the eutectic composition, are probably representative of the equi-atomic compound. Eq. [4] describes the vapor pressure of pure Cd as a function of temperature and may be combined with Eq. [3] to

Jan 1, 1962

By R. W. Smith, R. W. M. Lai, J. Leja

J. Leja (Professor, Dept. of Mineral Engineering, U.B.C. Vancouver, Canada) — I would like to offer some comments on the behavior of contact angle with time, treated in this paper. The authors should be congratulated for a clear exposition of these uncommon departures in the correlation between flotation and contact angle, in systems of importance to industrial practice. Some nine years ago Professor J. H. Schulman (presently at Columbia University, New York) and I reported on a similar study conducted at the Ernest Oppenheimer Laboratory, Cambridge, England.' The systems used by us had, how- ever, no direct practical application at that time, as mercury in solutions of xanthates was tested with a variety of alkyl-aryl polyoxyethylene frothers which were then new to flotation practice. Further, the paper dealt with findings contrary to the then widely held belief that the contact angle established in collector-solution is unaffected by the addition of a frother. Correlation with flotation, or lack thereof, was not sought, though we did suggest that in many cases the selectivity of frothers might be influenced by the dynamic contact angles. We also stated (on p. 243,

Jan 1, 1968

By André G. Journel

Geological study of the Prony Nilaterite (New Caledonia) began in 1969 and included drilling, geological mapping and laboratory studies. The deposit is the product of weathering of basic rocks. From top to bottom, the following zones can be distinguished: a compact ferruginous cover; ore associated with yellow laterite, containing 1.0-1.5% Ni and low in impurities (SiO2, Mg); an intermediate silicated ore containing 1.3-2.0% Ni and higher percentages of impurities; garnierite ore much richer in nickel (2-4%) but high in SiO, and Mg contents (Mg up to 20%) ; and parent rock, largely peridotites. Distinction between types of ore is essential because the high grade ore (silicated and granierites) is penalized for its high Mg contents that demand additional acid treatment. All studies made distinguish two types of ore, laterite and silicated.

Jan 10, 1973

Weston Portable Electrodynamometer The Weston Electrical Instrument Co. of Newark, N. J., believes that problems hitherto considered impossible of solution in the designing of portable electrodynamometers have been solved in its new models. The voltmeter, Model 341, is an instrument' of precision adapted to use on alterating- or direct-current circuits, guaranteed to an accuracy of 0.25 per cent. full-scale value either on direct or alternating-current circuits of any frequency to 133 cycles per second and commercial frequencies even as high as 500 cycles per second with very slight error. The polyphase electrodynamometer, Model 329, is accurate to 0.5 per cent. under the same conditions.; Double ranges are furnished in all instruments of this model. All current ranges can be used for 100 per cent. overload indefinitely without introducing error in Models 310 and 329.

Jan 12, 1915

Dr. F. W. C. Schniewind, New York, N. Y.:—Mr. Vogel speaks of briquetting the flue-dust by means of lime. I learned recently in Europe of a process employed with considerable success at one of the blast-furnaces, where blast-furnace cinder is used with lime. The lime and cinder are mixed with the flue-dust, and exposed to superheated steam, which converts the blast-furnace cinder into cement. Briquettes are then formed in the usual way. Mr. Vogel :—The process referred to is the " Scoria process," which has not been in use for some time past. For that reason, I did not mention it. Prof. Arthur L. Walker, New York, N. Y.:—I would ask the commercial name for magnesium chloride, and where it can be obtained ? Mr. VoGel :—I mentioned magnesium chloride, because it has been used abroad to a large extent. In Germany it is obtained as a by-product in the manufacture of potash-salts; in the United States we have been using chloride of lime, which is cheaper. Otto Sussman, New York, N. Y.:—What is the cost of this process ? Mr. Vogel :—The cost is exceedingly low. I can give you the figures from abroad, but not for the United States, because the system has not -yet been used here commercially to

Jan 1, 1913

By C. T. Holland

This discussion is concerned with those com-J- paratively infrequent bumps that eject material from the failed mass with enough energy to wreck heavy machinery and seriously injure or kill people. In such cases there is a loud report, and the pressure waves set up in the mine atmosphere wreck ventilation controls several hundred feet from the site of the failure. Vibrations are induced in the earth's crust which may be detected several miles from the point of origin, and explosive gases may be released in large quantities." Usually a dense suspension of dust is produced from the failed mass, together with dust placed in suspension by the resulting air blast. These rock bursts or bumps have also been called mountain shots, bounces, pillar bursts, and crumps. Such occurrences, when extensive, are serious catastrophes, and may force abandonment of the mine.' CAUSES OF ROCK BURSTS Rock bursts in coal mines have occurred in sev-eral places under diverse geological conditions, mining methods, and/or practices. A study of many such occurrences indicates that they depend on the following conditions: 1) cover thickness of 500 ft or more, 2) cover composed of strong members and having a strong member lying close to or on the coal bed, and 3) a floor that does not readily heave. The minimum thickness of cover under which coal mine rock bursts occur is based on observation. Under unusual circumstances involving very strong roof members and/or mining systems, and/or practices especially likely to induce bursts, a burst conceivably could occur under less roof. Under special circumstances rock bursts have occurred in marble quarries almost at the surface.' Furthermore, under very heavy cover it is likely that controlling roof members need not be as strong and as close to the coal bed to cause bumps. Just what constitutes a strong roof or roof member is open to question. Obviously the strength of a roof member is determined by its thickness, the distance between bedding planes across which little or no bond exists, the spacing and development of joints, and the inherent strength of the rock material. Strata sections showing roofs under which rock bursts in coal mines have developed are illustrated in Fig. 2. In several instances the strength of rocks composing the roof of mines developing bumps has been tested. The tests (Table I) show that these rocks develop considerable strength in compression, bending, and shear and that in some cases the strengths are very high. No quantitative data are available concerning joints in roof members over coal beds where rock bursts have occurred, but the author has examined many mines subject to bursts and has received the impression that joints in the shales immediately over the coal beds are always present and well developed. In the main sandstone or conglomerate members themselves, however, where observed, he has yet to see a fracture system indicating well developed joints. Undoubtedly joints are present, but the evidence indicates that they are few, poorly developed, and widely spaced. In a mine subject to bumps, moreover, actual measurements of roof spans up to 225 ft between supports under a cover of about 800 ft have been made before roof failure occurred. Such spans signify strong roof. In coal beds subject to rock bursts, the bottom rock is usually a sandy shale. A few tests (Table I) have been made on the floor rock of coal beds. Observations in mines indicate that they are usually weaker than roof rocks and that under load they show more plastic effects. Observation in ground subject to bursts invariably indicates a relatively strong floor highly resistant to heaving, although some heaving may occur. Other factors listed as favorable to rock bursts are: 1) mountainous surface; 2) steeply dipping beds; 3) proximity of faults, folds, and other similar geologic structures. Many bursts have occurred in mines under mountainous country, although many bursts in mines under a surface with little relief indicate that thickness of cover, not relief, is the essential factor. In steeply dipping beds, many bursts occur in mines that are essentially flat, and rock bursts have been recorded in beds dipping as much as 35o Most rock bursts in the U. S. occur in beds that dip less than 10 pct. It is also true that most U. S. coal is produced from beds dipping less than 10 pct. Geologically, faults are regarded as providing stress relief, but in the vicinity of faults, as well as sharp folds, it would seem that residual stresses could be present. The fact that rock bursts occur in areas remote from faults and sharp folds suggests that their presence is not necessary for this phenomenon to take place. There have been many bursts close to faults and folds, and it may be assumed that occasionally such structures accentuate their occurrence3 The conditions and circumstances under which they occur, coupled with the effects produced, leave In the Crowsnest Pass coalfield, British Columbia, a rock burst is estimated to have released 1.8 million cu ft of methane.

Jan 1, 1959

By H. D. Kessler, R. J. Van Thyne

Phase diagrams of the titanium-rich portion of the ternary systems from 0 to 10 wt pct Al and 0 to 1 wt pct 0, N, and C were determined. Micrographic analysis of annealed high purity arc melted alloys was the principal method of investigation and was supplemented by X-ray diffraction. TITANIUM-ALUMINUM alloys exhibit excellent properties, particularly for elevated temperature use. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the effect of the interstitially soluble contaminants, oxygen! nitrogen, and carbon, on the Ti-A1 system. Using high purity arc melted alloys and micrographic analysis of annealed samples as the chief method of investigation, titanium-rich partial phase diagrams were determined for the ternary systems. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9+ pct pure) produced by the New Jersey Zinc Co. and Foote Mineral Co. The aluminum was obtained from the Aluminum Co. of America in the form of sheet. The given analysis was: Si, 0.0006 pct; Fe, 0.0005; Cu, 0.0022; Mg, 0.0003; Ca, <0.0006; Na, <0.0005; and Al, 99.99. High purity titanium dioxide purchased from the National Lead Co. was used in the preparation of the oxygen-bearing alloys. The spectrographic analysis of this material was as follows: SiO,, 0.07 pct; Fe,O,,, 0.002; A1,0,, <0.001; Sb,O,, <0.002; SnO,,, <0.001; Mg, <::0.001; Cb, <0.01; Cu, 0.0004; Pb, 0.002; Mn, <0.00005; W, <0.01; V, <0.002; Cr, <0.002; Ni, <0.001; and Mo, <0.002. Special spectroscopic graphite rod purchased from the National Carbon Co. was used in the preparation of the Ti-A1-C alloys. Alloy Preparation: Alloy ingots weighing 10 grams were melted in a nonconsumable tungsten electrode arc melting furnace using water-cooled copper hearths and a helium atmosphere. The arc was struck on a tungsten stud in the copper block to minimize contamination from the electrode. Details of the techniques have been reported.&apos;, &apos; Each ingot was inverted and remelted a minimum of four times to insure homogeneity, without opening the furnace. Remelting small control ingots of iodide titanium under similar conditions resulted in no measurable hardness increase, indicating contamination-free melting conditions were used. The alloy charges and resultant ingots were weighed to the nearest milligram. Only small weight losses were obtained upon melting, indicating that the actual compositions were very close to the nominal compositions. Check analyses substantiated this. Oxygen and nitrogen were added during ingot preparation as master alloys. An oxygen master alloy containing 25 wt pct 0 was prepared by melting iodide titanium and pressed titanium dioxide (40 pct 0) powder. The Ti-25 pct 0 alloy is more easily handled during weighing and charging than the pressed TiO, powder. Chemical analysis indicated that titanium-nitride received from an outside source contained large amounts of impurities (2.7 pct Ca). Therefore, a master alloy containing approximately 12 pct N was prepared by melting nitrided sponge titanium. As the sponge melted with difficulty, the alloy was diluted by addition of titanium to lower the melting point. The chemical analysis of the final alloy was 6.69 pct N. Both master alloys are friable and were used as —8 +16 mesh lumps resulting from crushing the ingots. NIelting the Ti-A1-0 and Ti-A1-N compositions five times produced homogeneous ingots. The preparation of homogeneous carbon-bearing alloys caused considerable difficulty. Alloys containing less than 1 pct C were prepared using spectrographic graphite rod, 1/8 in. diameter by 1/8 in. long. However, the graphite did not dissolve even with long melting times and many remelts. The ?/s in. pieces of graphite were used rather than powder because the low density powder is troublesome in arc melting.

Jan 1, 1955

By Daniel C. McLean

Copper concentrates produced by many operations in the United States and South America contain chalcocite (79.9% Cu) as a major component, yet the grades of these concentrates rarely exceed 25 to 28% Cu. Mineralogical studies made by E.P. Cadwell indicated that the low grades were caused by dilution by pyrite rimmed with secondary chalcocite. Laboratory and plant tests proved that concentrates could be significantly upgraded by using a simple, low cost cyanide leaching technique to dissolve the rims and reject the pyrite. The many advantages of this new procedure are cited and the process steps and a typical flowsheet are described.

Jan 1, 1984

By Nick Holonyak

Halogen vapor-transport synthesis of Ga(As,-,Px) and its preparation into laser junctions are described. Electrical and optical properties of Ga(As,-,PX) laser junctions are discussed. The present limitations in these properties are related to material proble?vzs and the very early state of development of Ga(As,-,PX), and are discussed in this context. Inhonzogeneity problems, fluctuation of As :P ratio, and problems with deep-level contaminants are described and related to Ga(As,-,PX) junction performance. Laser junctions are demonstrated which operate to wavelengths as short as 6470 A (77°K). The prospect that Ga(As,-,P,) will operate to wavelengths perhaps 100A shorter is mentioned. IN this paper we wish to describe some of the more important features of almost 1 year of experience in the preparation and properties of Ga(As,-,P,) p-n junction lasers. Because much data so far available are far from complete, some of the results still must be considered tentative and subject to correction and revision as work on Ga(As,-,P,) crystal problems progresses. Although the electrical, optical, and device properties of Ga(As,-,P,) junction lasers are understandably of considerable interest, the work to date points out that by far the most serious problems extant and those deserving first attention are problems involving the growth, doping, and perfection of Ga(As,-,P,) crystals. One of the most formidable of these is to grow Ga(As,-,P,) sufficiently free of deep levels, either due to contaminants or to structural imperfections, to allow fabrication of laser p-n junctions which can be cooled and not suffer from "freeze-out" of carriers on deep levels (and consequent double-injection behavior). In addition to the problems of growing crystals adequately free of deep levels and generally of the highest perfection, so that the best possible laser junctions can be realized, the further goal remains of increasing the phosphorus content well beyond 40 pct in an attempt to determine the practical lower wavelength limits of laser action in the Ga(As,-,P,) system. Even though the laser junctions prepared in Ga(As,-,P,) are of importance in their own right, we have considered them at this point mainly a means to study the growth and crystal problems of the material. It can be concluded that the laser junctions now available are almost completely limited by the purity and structural deficiencies of Ga(As,-,P,) crystals, and cannot be fairly compared with, for example, GaAs p-n junction lasers until Ga(As,-,P,) crystal growth has been more extensively developed. The basis for the statements above will become evident in the following sections which describe Ga(As,-,P,) crystal and junction preparation, and laser-junction properties. G(As,-,P,) CRYSTAL GROWTH As previously reported,2 we have found it convenient to employ the halogen vapor-transport process3 for synthesizing Ga(As,-,P,) crystals for use in laser junctions. Commercially available GaAs and Gap, separately prepared by halogen vapor tranport, are sealed in the desired ratio in a quartz vessel with a quantity of column-VI donor and a small quantity of metal halide which supplies the halogen for transport. The sealed ampoule, as shown in Fig. 1, is heated at a temperature in the range from 1025" to 1100°C at the position of the source GaAs and Gap. The GaAs and Gap are simultaneously vapor-transported and deposited as Ga(As,-,P,) at one end of the ampoule

Jan 1, 1964

By L. P. Teas

In spite of the influx of operators into the Gulf Coast anxious to retrieve their depleted production in other fields, and in spite of very active application of the most scientific geophysical methods to locate new producing areas, the results have been very discouraging and the year has failed to produce more than the average results for a Gulf Coast year. During the year seven new oil fields, some of which are still of very little importance, and one new gas area have been discovered. These fields are Tom Ball, Greta, Cleveland, Raisin and Garwood in Colorado County; Louise and Premont in Jim Wells County, and the new producing gas area near Ace in southern Polk County. During the year salt has been found for the first time at Carlos and Esperson. New producing areas have been developed on East Stratton Ridge, Hockley, Hull, Port Neches, near Pettus in Bee County, and on the O&apos;Connor Ranch in Victoria County. The total production for the Gulf Coast for the year was 62,837,435 bbl., an increase of 18,589,000 bbl. over 1932. During the year, 1307 wells have been drilled of which 207 were wildcats, compared with 653 wells and 141 wildcats the previous year. The total daily production at the end of the year was 165,201 bbl. At present there are 3100 oil wells producing. The average production per well is 55.5 bbl. per day. The price of crude fluctuated considerably during the year, beginning at 80c per barrel and closing the year at $1.04 per barrel. Completion data for 1933 are as follows:

Jan 1, 1934

By J. Gurland

The strength variation ofWC-Co alloys with composition and particle spacing falls into two ranges. 1) Above a critical value of the mean free path, the strength follows a dispersion hardening relation; it is proportional to the volume fraction of WC and in-versely proportional to the particle size. 2) Below a critical value of the mean free path, the strength variation is based upon the Griffith criterion of fracture and is controlled by the case of crack propagation. The maximum strength is attained when the structure and load just satisfy the critical conditions for spontaneous crack propagation. THE relation between the strength and the structure of cemented carbides is of interest not only for its own sake but also for its contribution to the understanding of composite materials in general. The cemented carbides are essentially aggregates of a brittle carbide constituent and a ductile binder phase and, at certain structures of intermediate composition, the composite alloys attain strengths far higher than those of the separate constituents in bulk. It is this variation of strength with structure which will be discussed. The experimental procedures of sample preparation, mechanical testing, and quantitative metallo-graphic analysis have been described in Ref. 1. The reported strengths are the maximum fiber-stresses in bending calculated on the basis of completely elastic behavior. The plastic contribution to the over-all deformation is small and was neglected in the calculations (the elongation at fracture of the most ductile alloy, 50 pct WC-50 pct Co, is less than 0.5 pct).2 The pertinent structural parameters are: f, the volume fraction of tungsten carbide; p, the mean free path through the binder phase; the contiguity C, defined as the average fraction of surface area shared by a particle of wc with all neighboring particles of the same phase; and d, the average equivalent spherical diameter of the WC particles. The strength variation of WC-Co alloys with composition and particle spacing is shown in Fig. 1 and Table I, which are based partly on previously published data&apos; and partly on new experimental work which extends the range to higher values of the mean free path. Each data point represents the average of five samples. For a given composition, the transverse rupture strength reaches a maximum

Jan 1, 1963

By C. Schlumberger, M. Schlumberger

In order to explore electrically a terrain composed of a succession of horizontal beds, a current of known intensity i is caused to flow between two grounds A and B, and the resultant drop of potential , caused by the resistance of the earth, is measured between two given points in the soil, M and N. In practice it is convenient to choose the two points M and N so that they lie on the line AB and their midpoint coincides with the middle 0, of that line, although this is not imperative. When the lengths L and I of the two lines AB and MN are varied, equations are obtained which may be solved for the resistivity p of the subsoil at various depths. Recall briefly that the formula 4 x l gives the average resistivity, in the horizontal direction, of a layer of earth which extends to a depth1 about equal to L/4. This elementary concept is adequate for numerous practical applications. Nevertheless, it must be said that, in many cases, a rigorous mathematical analysis may be made, provided it is always a question of homogeneous, superposed horizontal beds. The authors expect to publish, later on, appropriate methods of calculation for some specific cases.

Jan 1, 1932