Search Documents

By E. Miller, J. M. Eldridge, K. L. Komarek

The liquidus curve of the Mg-Pb system was accurately redetermined. The compound Mg2Pb decomposes peritectically at 538.2° ± 0.3°C to liquid and to a compound p' which melts congruently at 35.0 at. pct Pb and 549.0° ± 0.3°C. The solidus curve of ß' was determined. X-ray diffraction studies indicate that 4' has an orthorhombic structure. Activity values of magnesium calculated from the phase diagram agree with those published in the literature. EXPERIMENTAL thermodynamic properties of binary metallic systems have to be consistent with values calculated from the phase diagram. In systems forming intermetallic compounds the shape of the liquidus curve near a compound is determined by the thermodynamic properties of the coexisting solid and liquid phases. Hauffe and Wagner' neglected the temperature dependence of the chemical potentials and obtained the potential differences of the components of the liquid alloys, relative to stoichiometric liquid. Their calculations were based on the liquidus curve and on the heat of fusion of the compound, and were only valid near the congruent melting point. Steiner, Miller, and Komarek2 developed equations which account for the temperature dependence and obtained the chemical potentials of liquid Mg-Sn alloys over the entire phase diagram from the liquidus and solidus curves and from enthalpy values with the pure components as the standard states. The Mg-Pb phase diagram has been studied by several investigators whose results have been compiled and critically evaluated by Hansen.3 Although the liquidus curve was poorly defined, the general features of the diagram, i.e., one congruent melting compound, Mg2Pb, of essentially stoichiometric composition, two eutectics, and limited terminal solid solubilities, seemed to be suitable for a similar thermodynamic analysis. A careful redeter-mination of the liquidus by thermal analysis revealed, however, the existence of another compound. The liquidus curve between the two eutectics was precisely delineated and the structure and solidus curve of the new compound were investigated. The revised phase diagram was thermodynamic ally analyzed to evaluate the activity of magnesium in the liquid alloys. EXPERIMENTAL PROCEDURE The magnesium metal (Dominion Magnesium Ltd., Toronto, Canada) had a purity of 99.99+ pct; lead (American Smelting and Refining Co.) contained 99.999 pct Pb. Most experiments were carried out in graphite crucibles. Several experiments were made in high-purity alumina (Triangle R.R., Mor-ganite, Inc.) and in Armco iron crucibles to test the inertness of the graphite crucibles. Chemical analysis of magnesium and detailed description of the procedure for thermal analysis have been given previously. For the determination of the solidus curve of the compounds, specimens of initial composition Mg2Pb were equilibrated in a closed isothermal system with magnesium vapor. The source of the magnesium vapor was an alloy which had a gross composition lying in the 0' + L field at the temperature of equilibration. As equilibrium was approached, the specimens lost magnesium to the two-phase reservoir thereby lowering the activity of magnesium in the specimens until activity and composition equaled that of the ß'/ß' + L boundary. Crucibles (1.9 cm ID by 2.2 cm OD by 4.1 cm high) and tightly fitting lids were machined from a molybdenum rod; small, shallow trays were fashioned from thin (0.005 in.) molybdenum sheet, and all the molybdenum components were degreased in hot carbon tetrachloride and then dried. The pieces were then degassed in vacuum at 950°C for about 6 hr. The two-phase alloy was placed at the bottom of the crucible and small specimens of the Mg2Pb compound, weighed on an analytical balance, were placed in two molybdenum trays above the two-phase alloy. The crucible was closed by forcing its lid on and then inserted in a titanium crucible. This crucible was evacuated, flushed twice with argon, and welded under argon. The specimens were equilibrated for about 1 week in a resistance furnace regulated by a Celectray controller, and the runs were terminated by water quenching. The specimens were again weighed and the equilibrium compositions were calculated on the basis that the weight losses were solely due to a loss of magnesium to the two-phase alloy. The structure of the B' phase was investigated by the Debye-Scherrer X-ray diffraction technique. Selected ingots from thermal-analysis experiments containing about 35 at. pct Pb were re-melted, slowly cooled, and crushed in an argon-filled glovebox until the entire ingot passed through a 50-mesh sieve. The powder was thoroughly

Jan 1, 1965

By Georges Fleming

The new burden preparation plant of ARBED Luxembourg, Belval- Works, which comprises 2 large sinter strands, is equipped with a process computer connected to a comprehensive process control system. The main jobs done by the computer are the control of the raw mix composition, and thus the monitoring of the stacking of the piles at the bed-blending plant, and the optimization of the sintering process. Among the optimization criteria, quality is considered as the most important. The sinter quality, characterized by the mechanical strength and the state of oxidation, is controlled automatically. The control system which we have dev loped is highly reliable; as a result, the standard deviation of Fe++, for the control of bivalent iron, has been narrowed to 0,5 % and the standard deviation of the IS0 + 6, 3 mm index, for the control of the mechanical strength, has been kept within 1 %. Thanks to these results, the combined savings in fuel consumption at the sinter plant and at the blast furnaces have covered the total costs of the optimization project in 2 years. By applying automatic control, the optimum driving range of the sinter plant has been defined and these new guidelines are used for monitoring the sinter production.

Jan 1, 1977

By Michael Hoch, Daniel B. Butrymowicz

The isothermal section of the Ta-Ti-Zr-0 system at 1500°C was investigated using X-ray diffraction and rrzetallographic techniques. Up to 71.4 at, pct 0 the system contains nine four -phase regions. Zsopleths at 10, 20, 30, 40, 50, and 60 at. pct 0 were constructed. The purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of tantalum, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct 0 on the Ti-0 and Zr-0 binaries and at 71.4 at. pct 0 on the Ta-0 binary. The Ti-Zr-0 system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by Hansen and Anderk, chmidt, Hayes, Roberson, and asche, and Hoch and athur.' EQUIPMENT The Same equipment as that for the study of the Nb(Cb)-Ti-Zr-0 system was used.' The X-ray dif- fraction patterns were analyzed with the help of the ASTM card set7 and NBS circulars.' MATERIALS The tantalum powder (99 pct pure), the titanium powder (99.6 pct pure), the tantalum pentoxide, and the zirconium dioxide used in this study were purchased from the Fairmont Chemical Co., Newark, N.J. The zirconium powder (99.4 pct pure) was obtained from the Charles Hardy Co., Inc., New York. Reagent-grade titanium dioxide was purchased from the Matheson Co., Inc., Norwood, Ohio. The oxides were dried in air at 700°C for 24 hr before use. Though the materials used were not "hyper-pure", the impurities present do not affect the results (lattice parameters, phase boundaries), within the experimental accuracy. PROCEDURE The samples were heated by induction in a vacuum furnace, and examined metallographically and by X-ray diffraction at room temperature. The procedure was the same as that in the Nb(Cb)-Ti-Zr-O work,' EXPERIMENTAL RESULTS AND DISCUSSION OF DATA A four-component system can be represented by a tetrahedron at a single temperature and pressure

Jan 1, 1964

By Michael S. Roscoe

In order to more accurately predict longwall surface subsidence over the Pittsburgh No. 8 Coal in Eastern Ohio, North American Coal Corporation's Quarto Mining Company undertook or participated in several subsidence studies. Due to the changing roof geology and rapid variations in the amount of cover two separate areas were investigated at two different mines to determine the subsidence response if any to these changes. Data generated from these studies were compared with NCB derived,data for accuracy and then used to predict subsidence under houses, gas lines and other critical man made structures. The following report summarizes the results of these studies as well as the subsidence case histories of gas lines, transmission towers, houses and water wells. Problems that were encountered during both phases of this process (investigation and subsequent application) are also included.

By S. Stutz

Three years ago, at the Philadelphia meeting, in February, 1881, the author had the pleasure of presenting to the Institute a paper on coal-washing machinery.* Since that time many new machines, with important improvements and labor-saving apparatus, have been introduced, the construction and description of which may be of interest to some of the members of the Institute. By referring to the above-mentioned paper, and more especially to Plate IV., representing a vertical section of a coal-washer, it will be noticed that the bottom of the plunger-box B is made level or horizontal, and supports a spring-buffer F for the purpose of limiting the down-stroke of the plunger P and receiving the impacts of the latter. Althongh the construction of the box, in view of these impacts, received from the start the proper attention (the bottom of the chamber 3 being made of three thicknesses of 3-inch planks, resting on 6-inch sqnare columns), yet, through careless working of the machinery, without the necessary water in the box, it proved in several instances not strong enough, and had to be changed. To prevent such interruptions in future, it became necessary to devise some means for relieving the machine from the impacts of the plunger altogether. This has been accomplished by the arrangement shown upon Plate I. of this paper, representing a new waesher; and not only has the difficulty been overcome, but also sorne other advantages have been obtained, as will be seen further on. The compartments +, A' of the separator-box have been set upon heavy cast-iron brackets B, leaving sufficient space below the bottom for the buffer F and the sediment-valve K. By means of the plunger-rod 6 passing through the stuffing-box s to the outside, and provided at its lower end with a shoe a, the impacts of the plunger are now transmitted from the buffer F directly to the foundation. At the same time a better guide for the plunger P in its up and down movement has been obtained. The plunger of the former machine had only the guide I and the yoke Y, whereas the new machine has an additional guide in the stuffing-box s, thus preventing wear and friction of the plunger against the lining of the box. Further-

Jan 1, 1884

By Harry L. Brown, Philip E. Armstrong

Young's modulus doto ore presented for W, Mo. Ta. V, Cr. Ni, Ti, and Zr as a function of temperature up to about 0.7 of the melting points. A plot of reduced temperature us reduced modulus produces a general correlation except for titanium and zirconium. Young's modudlus data for some representatiue commercial graphites are given up to 2400°C. All results were obtained from longitudinal resonance-frequency measzrrements of 4-in. long samples, corrected for simultaneously measured thermal expansion. Comparison of poly crystalline and single-crystal tungsten behavior indicates that all the observed modulus values are frequencv -dependent at the higher temperatures. STATIC measurements of elastic properties of materials at elevated temperatures are extremely difficult to make since the elastic behavior is obscured by relatively large first-stage creep effects. Dynamic methods which avoid this difficulty by utilizing the measurement of the resonance frequency of a simple vibrational mode have been described in the 1iterature.l-3 The authors have extended the operating temperature range of this type of measurement to above 2000°C and have described the equipment elsewhere.~ The Young's modulus data presented here were obtained with this equipment, using samples about 4 in. long and 1/4 in. diam, supported horizontally at the center and excited to the fundamental longitudinal resonance frequency. Young's modulus was calculated by the formula: E = 4f2f2p where E = Young's modulus, / = frequency, 1 = length, and p = density. Dilatometric data were obtained simultaneously by optical measurements of the change of length of the sample. For the metals tested, an attempt was made to obtain modulus values that would be representative of the pure, strain-free, randomly oriented material. All of the graphites studied exhibited a high degree of elastic anisotropy, while the method assumes an isotropic homogeneous material. However , when the values for Young's modulus obtained for AUC graphite were compared with those taken from static measurements at room temperature they were found to be only about 4 pet higher. This is excellent agreement considering the low precision of modulus calculations from stress-strain curves. The difficulty in using data of apparent Young's modulus for anisotropic materials arises when the attempt is made to use these data and shear-modulus data to obtain Poisson's ratio. The results are usually meaningless and sometimes absurd.' RESULTS Table I lists the sources, impurity content, thermal history, and dilatometric constants of the metal samples that were investigated. All the metal samples were tested under a vacuum of 1 to 5 x 10-5 Torr. Where our dilatometric data agreed with previously published data, the table lists the previous values and the literature reference. Where no reference is given, the constants were determined from our dilatometric data. Table II presents the modulus data in units of millions of psi as a function of temperature in degrees centigrade. The numbers were obtained from curves fitted to the experimental data. For some types of calculations, such as those attempting to correlate creep data, the slope of the modulus curve is of interest, and this information also is reported in Table 11. It is always tempting to try to fit physical-property data into some general pattern and then use this pattern to predict the behavior of other similar materials. The general pattern for an elastic modulus of a metal seems to be a linear deoro- with increasing temperature Over the range between 0.1 and 0.4 of the melting temperature, then a progressive1y decreasing value up to the melting point. Metals appear to retain finite moduli

Jan 1, 1964

By H. H. Kaveler, W. R. Evans, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

By W. R. Evans, H. H. Kaveler, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

By J. O. Brittain, E. Lautenschlager

Yield point measurements were made on polycrys-talline specimens of a iron deformed various amounts at 770, 1950, or 273°K, aged, and redeformed at 77: 195°, or 273°K. When the prestrain temperature is lower than that subsequent to aging, the yield point return is suppressed relative to specimens deformed at the same temperature both before and after aging. The degree of suppression is a function of both the magnitude of prestrain at the lower temperature and the difference between the deformation temperatures before and after aging. It is proposed that the suppression is caused by the formation of dislocation barriers during the initial low-temperature deformation. The aging kinetics of polycrystalline a-iron wires deformed at 77o or 303oK were studied at 44 " and 64 "C using internal friction measurements. No change was noted as a result of the difference in prestrain temperature. IN an earlier investigation1 it was observed that the return of the yield point was suppressed when a poly-crystalline specimen of a iron was plastically deformed at 77oK, aged at room temperature, and subsequently tested at room temperature. In order to investigate this observation, a research program was undertaken to measure the effect of prestrain temperature on the strain aging of a iron.' According to Thomas and Leak,3 return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solution, while the return of the yield point as a function of aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,4 the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point upon restraining. In this experiment, both methods of measuring strain aging were employed in order to have two independent measurements of the strain aging phenomenon. In a previous study,5 the strain aging kinetics of a similar lot of a iron were measured for specimens which were prestrained and tested at the same temperature over the range of 77" to 273°K. Although some differences were found in the correlation of the two methods employed for measuring strain aging, the kinetics of strain aging were unaffected by the change of prestrain and test temperature. In another study,6 dislocation line tension and the density of the solute atmosphere were found to contribute to the return of the yield point when ingot iron specimens were prestrained at 303°K and tested at a lower temperature, namely 77°K. This paper is concerned with changes in strain aging kinetics produced by pre-straining at 77" to 303°K and testing at either the prestrain temperature or at higher temperatures up to 273°K. EXPERIMENTAL PROCEDURE The polycrystalline a iron specimens used in both the tensile and internal friction tests were 0.033-in. diam ingot iron wires, wet hydrogen treated and re-carburized. A more detailed procedure for processing a 3/16 in. ingot iron rod (nominal wt. pet composition: Fe - 0.013; C - 0.0125; Mn - 0.023; Si -0.005; P - 0.0023; S - 0.11; Cu - 0.004 N) to 0.033 in. diam specimens containing approximately 0.020 wt pet C and no detectable nitrogen with a grain diameter of 0.033 to 0.040 mm is given elsewhere.5 Immediately prior to testing, specimens were solution treated for 15 min at 700o ± 2°C in a static vacuum of less than 50 ?. of Hg and rapidly quenched into an ice-water bath while still enclosed in a 3 mm quartz vial. The internal friction specimens had 8-in. gage lengths and the tensile specimens had 2-in. gage lengths. The wires used as tensile specimens were first run as internal

Jan 1, 1962

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By E. R. Johnson

The copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the westem flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past I5 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7½ gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by I-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55½-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73½-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bill serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 13/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7½ McCully gyratory crusher set at 13/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73½ by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1949

By L. E. Young

LOADING machines may be classified in several ways: (1) Machines which cut or break down and load .the coal; (2) machines which simply load the coal; (3) devices which load and transport the coal; (4) de-vices which elevate; (5) devices which transport the coal after it has been shoveled onto the device. There are many types of mechanical loading devices, Bull. 17, Coal Mining Investigations, under the auspices of Carnegie Institute' of Technology, U. S. Bureau of Mines, and the Advisory Board, listing 31 exclusive. of -the large shovels used in thick coal seams. Mechanical loading of coal is not in its infancy; I think some of the early patents go back to 1890. One large coal company, properly called the early leader in this field of mechani-zation, has about 26 large machines at work. This company spent about thirty years in developing a ma-chine, and at the present time is loading approximately two million tons of coal a year in its mines. The chair-man directed a question at the previous speaker; inquir-ing if real progress was being made in mechanical load-ing. The experience of the company just referred to is in itself an adequate answer. A review of a list of mines using mechanical loading devices shows that there are 28 mines which we may say are 100 per cent mechanical. There are four more mines which have been 100 per cent mechanical, but which are idle at this time on account of labor condi-tions. There are at least 25 more at which the tonnage is more than 50 per cent mechanical. In speaking of a 100 per cent mine I do not mean that every pit car of coal is loaded by machine, because when complete, re-covery of the coal is attempted it is not practical to load all the coal at, the break line. In order to load the last 5 to 10 per cent of coal with a minimum of gob material and in order to keep the. working places along the break line timbered in a safe manner it is generally desirable to use a few hand loaders. At a certain mine operat-ing on the block system 90 percent of the coal is being loaded by what is properly a mechanical loading: device, and about 10 per cent -is being loaded by hand. This 10 percent is right off the break line, out of what might be called, the screen pillar. The mines referred to are scattered over the country, . in seven different' States, and the equipment used is produced by ten different machinery companies. As to size, these mines vary from small mines of 500 tons mining capacity-up. In one instance a company with one loading machine is producing an, average of 450 tons per day. One of the large mines that is idle pro-duced at the. rate of 4300 tons per day, of which 97 per cent was actually loaded by machinery.

Jan 8, 1928

By J. C. Swartz

Measurements of the effect of precipitation stresses on the solubility of cementite (Fe3C) precipitates in a iron are reported. Solubilities were determined from measurements of the Snoek relaxation due to interstitial carbon after quenching from various equilibrium treatments. Stress-free precipitates were obtained by a spheroidizing treatment of vacuum-melted Fe 0.06 wt pet C. Subsequent equilibration treatments were designed to suppress nucleation of other precipitates. The results for stress-free cementite give a heat of solution of 14.8 i 0.2 keal per mole and an entropy change of 1.1 i 0.2 eu in the temperature range 400" to 715°C. Comparison with previous data indicates that the heat of solution increases about 6 keal per mole as temperature increases from 700" to 1000°C. Data on self-stressed cementite in quench-aged specimens of Fe 0.013 wt pet C indicate 1) an apparent heat of solution of 12.1 i 0.4 keal per mole in the range 280" to 690°C, 2) a strain energy of- 1.1 keal per mole Fe3C accompanying precipitation at 280°C, and 3') a gradual decrease in the strain energy of precipitation with increasing equilibration temperature. In com-parison with 2 and 3 the strain energy calculated for an isotropic model is 1.7 keal per mole Fe3C. The lower values obtained from the experiment indicated substantial stress velaxation by dislocation motion. WHEN a supersaturated solution of carbon in a iron is aged at temperatures in the range 200o to 700oC, the carbon clusters by interstitial diffusion and forms cementite (Fe3C) precipitate particles. Unstressed cementite has a volume per iron atom 9 pet higher than that of a iron;' hence, cementite precipitate particles are usually under pressure from the iron matrix. The pressure would tend to increase the solubility of cementite in iron.' This report describes anelastic measurements of the solubilities of self-stressed and stress-free cementite in a iron. Previous determinations of the cementite solubility are summarized in Table I. The method of cementite formation for each reference was studied to ascertain the state of stress of the cementite. The results judged to be for stress-free and stressed cementite are distinguished in the table. In the next section an estimate of the stress effect is obtained which is clearly too small to account for the large difference between the previous results in parts A and B of the table. THEORETICAL Let AGO be the standard free-energy change of the reaction Fe3C (eem.) = 3Fe (a) + C (in a) [1] in the absence of stresses. Since cementite precipitates appear to be rather pure10 and the carbon is so dilute in the iron,8 the cementite and iron of Eq. [ I] for the stress-free case have essentially unit activities and the activity of carbon equals its atom fraction xoC Then the stress-free equilibrium is expressed by RT In XoC = -?GO 121 To first approximation the change in the chemical potential of carbon due to the precipitation stresses equals the elastic strain energy W accompanying precipitation of a mole of cementite.2 Hence, in the presence of the precipitation stresses the equilibrium is described by RT In x sq = -?G° + W [3] where xsC is the mole fraction of dissolved carbon in the stressed case. An approximate value of W can be obtained from analysis of the inclusion problem in elasticity theory. The inclusion is a small portion of the matrix phase which has suffered a transformation while still imbedded in the matrix. In the absence of the constraint of the matrix the transformation would be equivalent to a uniform dilational strain eT. Both the matrix (a) phase and inclusion (0) phase are assumed to be homogeneous, isotropic materials. When the a and 0 phases have the same elastic moduli, which is approximately true for iron and cementite,11 the total strain energy per mole ß is12 2µVß(eT)2(3 +4 µx)-I [4]

Jan 1, 1968

By Frederick Prime

IN this second supplementary list no titles to which an * is. Pre-fixed have been seen by the compiler; and he will be most thankful to have, any omissions or inaccuracies in the list sent to him to be published as a third supplement in the next volume of- the Trans-actions. The author is indebted to Prof. J. J. Stevenson, of New York, Prof. P. R. Uhler and John W. M. Lee, Esq., of Baltimore, and Lloyd P. Smith, Esq., of Philadelphia, for valuable assistance. OFFICE, ALLENTOWN IRON COMPANY, 230 SOUTH THIRD STREET, PHILADELPHIA, September 5th, 1881. ALABAMA. Geological Survey of Alabama. Report of Progress for 1879 and 1880, by Eugene A. Smith, State Geologist. Montgomery, 1881. 8vo., 158 pp., and 2 maps. CALIFORNIA. Omit Report of Hon. T. Butler King, in Supplement 1. For Trash's Geology and Industrial Resources, etc., in Supplement I., read Tyson's, etc: Fremont's Memoir on Upper California, is also published as XXXth Congress, 1st Session. Senate Mis. Doe., No 148, and has a map. For Randall's Report in Supplement I, read Report of the Special Committee in favor of a Geological Survey, submitted by Mr. Randall, April 24th, 1851. a.d., 1851. 8vo., 1.9 pp. XXXIst Congress, 1st Session, Sea. Ex. Doc., No. 47, Part 2 [Part 1 is Tyson's Report.] Report of the Secretary of War in further compliance with the Resolution of the Senate, calling for Copies of

Jan 1, 1881

By Frederick Prime

In this second supplementary list no titles to which an * is pre fixed hare been seen by tlie compiler; and he will be most thankful to have any omiesisne or inaccuracies in the list sent to hiin to be ptiblisi~cd as a third supplement in the next volume of the actiotra. The author is indebted to Prof. J. J. Stevenson, of New Tork, Prof. P. R. Uhlcr and John 'CV. M. Lee, Esq., of Balti more, and Lloyd P. Smith, Esq., of Philadelphia, for valuable assistance. office, allkntorn iron compaxy, 30 South Third Street, Philadelphia, September 5th, 1881. Alabama. Geologiml Survcy of Alabama. report of Progress for 1879 and 1880, by Eugene A. Smith, State Geologist. Montgomery, 1881. 8vo., 158 pp., and 2 maps. California. Omit Report of Hon. T. Butler Ring, iu sopplemeut I. For Trask's Geology and Illdustrial honrecp, etc., in Supplenlvut I., read Tyson's, etc. Fremont's Menloir on Upper Califijrnia, is also published as XXXth Congress, lat Session. Senate Ms. Doc., No 148, and has a map. For Randall's Report in Supplement I, rend Report of the Special Committee in favor of a Geological Snrvey, subrn-itted by Mr. Randall, April 24th, 1861. n.d., 1851. 8cWo., 19 yp. XXXIst Congress, 1st Session, Sen. Ex. Doc., No. 47, Part 2 [Part 1 is Tyson's Report.) RejW of the Secretary of War in further compliance with the Resolution of the Senate?, calling for Colbies of

Jan 1, 1881

By A. W. Schlechten, R. F. Doelling

Parkes' process crusts were vacuum distilled using a shortened Pidgeon retort. Zinc was effectively removed below 800°C and recovered as a zinc sheet easily stripped from the furnace liner. Lead dasdistillationazinc required about 950°C and the resulting lead condensate tillationtended to stick to the thin metal liner. Final purity of residue is limited only by nonvolatile metals such as copper. THE successful commercial application of vacuum distillation for the removal of zinc from lead, as described by W. T. Isbell,' raises the question of whether or not a similar method can be used for other metal separations. Preliminary laboratory experiments on the vacuum distillation of Parkes' crusts by one of the authors' gave such encouraging results that it was decided to make a series of tests with large scale equipment to determine the results that might be expected in plant operation. The pilot-plant test results are reported in this paper. The great advantages of vacuum dezincing are its simplicity, the relatively low temperature of operation, and the fact that the zinc is recovered in the metallic state ready for use again in the desilveriza-tion of lead bullion. These same advantages and others would be realized from the vacuum distillation of the zinc-lead-silver crusts made in the Parkes' process. Zinc readily will distill over at temperatures of 800" to 900 °C as contrasted with the 1200°C or more used in the Faber du Faur furnace. Furthermore, the recovery of zinc as metal is practically perfect since there is no loss by oxidation or fuming. If the vacuum distillation is continued and hastened by raising the temperature to around 1000°C, the lead will distill over at an appreciable rate and deposit in a warmer zone of the condenser. This lead will contain a small amount of silver, but it can be returned to the desilverizing kettles and there is not the chance of loss that there is in disposing of the rich litharge from cupelling. The lower temperatures required will mean a saving of fuel and less wear on the equipment. One further point is that the vacuum distillation could be run on a small scale practically continuously, so as to avoid the accumulation of large amounts of silver-rich material and the need of assembling a large crew for special cupellation runs. It should be pointed out here that the final purity of the silver residue will depend on the copper or iron content of the crusts, as these and other metals with low vapor pressure will not be eliminated. The idea of treating the silver-zinc-lead crusts from the desilverization of lead bullion by vacuum distillation is not a new one, but such experiments have not been reported, as far as can be determined. In 1912, T. Turner presented a paper3 before the Institute of Metals on the vacuum distillation of brass, and a member of the audience suggested that he try his method on Parkes' crusts. In 1935, W. J. Kroll, noted for his discovery of debismuthiz-ing lead by calcium additions, published a paper' on vacuum distillation of metals and pointed out possible applications in the lead industry. Principles of Separation The successful separation of two or more metals by distillation depends upon an appreciable difference in the effective vapor pressures of the metals in the alloy to be treated. The vapor pressures of the common metals have been determined with considerable accuracy; for example, at 800°C the vapor pressures of the individual metals which are of particular interest in this paper are about .as follows: Zn, 241 mm; Pb, 0.0553 mm; and Ag, 0.0000276 mm. Unfortunately,, data are not available on the activities of the components in the ternary system Zn-Pb-Ag, but it can be estimated that on the basis of the vapor pressures of the individual metals a good separation can be made by distillation. The preliminary laboratory tests previously mentioned' supported this assumption. The pilot-plant size vacuum distilling furnace is shown in Fig. 1. It consisted of an abbreviated Pidgeon retort, 5 ft long with an ID of 8 in., heated by six silicon carbide elements placed symmetrically

Jan 1, 1952

By J. P. Givry

The bath and the liquid metal in the aluw~inuw~ electrolytic cells are moving under the action of the Laplace forces. Consequently there are differences in level at the interface of the liquid. This phenomena is studied by means of a computer; the characteristics of the mathematical model used are presented with the results corresponding to two typical cases. This study gives a new and origi~zal interpretation of magnetic ej-jects; their action depends very closely on the hydraulic phenomenon which explain the sensibility of the cells to the slope and thickness of solid bath frozen around the pot. MAGNETIC effects produced in the electrolytic cells used for the production of aluminum are known to exist, a factor whose importance is well-known by producers through its influence on cell operation and output. In particular, these effects bring about movements in both the bath and metal as well as interface variations in level that are detrimental to sound electrolysis . A direct study of these effects by means of an experimental device would raise a number of problems particularly difficult not to say impossible to solve in the present state of techniques. It is for this reason that we had recourse to an electronic computer for working out the speed and pressure distribution within the liquid in the cells. We have assumed that all other possible causes for movement, such as thermal convection and evolution of gas at the anode, are acting without any connection with magnetic effects, and that consequently we may study each of these causes separately. A basic cause for magnetic effects lies in the presence of Laplace forces within the bath and metal. Electric current and magnetic field distribution have been calculated with the help of an electronic computer, and two communications about it have already been made to AIME.* 1) PRESENTATION OF THE MATHEMATICAL PATTERN In order to solve this problem, it was essential to assume a number of simplifying hypotheses with regard to both the geometry of the actual cells and the phenomena themselves. A first simplification consisted in assuming that the movements of the conducting liquid modify neither the electric currents nor the magnetic fields. In consideration of the magnitude of the values involved this assumption seemed accep-tible. 1.1) Finding the Equation of the Problem. The problem raised consisted in determining the flow of two viscous immiscible liquids with different densities subjected in a complex environment to gravity and Laplace forces. As a matter of fact, the sum of the external forces acting on the liquids is: F = JAB +pg where F = volume energy, B = magnetic field, J = current density, p = specific gravity, g = gravity. In the case of a laminar flow and assuming that the liquids are Newtonian and incompressible liquids, the equations governing movements are the following: 1) Navier Stokes' equation written in vectorial form: In fact one tries to find a steady-state solution, so aVx/at = 0; besides, one assumes that the movements are slow enough for quadratic terms such as Vy(a Vx/ay) (of round about the square of speed) to be neglected in front of the viscosity term: pAV, so

Jan 1, 1968

By J. D. Anthony

The Australian continent possesses significant reserves of a wide range of minerals, including bauxite, coal, copper, diamonds, gold, iron ore, lead, manganese, mineral sands, nickel, phosphate, silver, tin, uranium, and zinc. Australia's identified economic resources of many minerals are very large as indicated in Table 1. A sophisticated and highly experienced mineral industry is now an established feature of the Australian economy and Australia is the world's largest exporter of iron ore, alumina, mineral sands and refined lead and amongst the leading suppliers of many other commodities such as coal, lead and zinc ores/concentrates, nickel, refined zinc, tungsten concentrates and bauxite. The industry exports 70% of its production. This is reflected in the value of Australian mineral exports which have grown from about $200m in 1960/61, comprising 10% of total export receipts, to about $1265m or 29% of export income in 1970/71 to around $7061 representing 37% of Australia's total export income in 1980/81. Details of the more significant minerals are as follows: Japan (42.1%) USA (11.3%) ASEAN (6.3%) UK (5.9%) F.R. Germany (3.8%) Republic of Korea (3.4%) New Zealand (2.6%) Also see Table 2. AUSTRALIA'S MINERAL RESOURCES POLICIES Federal and State Governments' Responsibilities Australia has a federal system of government comprising six States, a self-governing Territory and a Federal Government. Under the Australian federal system the Constitution sets down the powers of the Federal Government. All powers not assigned to the Federal Government in the Australian Constitution reside automatically with the States. Certain of these broad powers result in the Federal Government having a significant influence on resources development. For example, in being responsible for economic management, the Federal Government's fiscal and monetary policies have an important effect on industry as well as on State finances. In particular, the taxation regime employed by the Federal Government is of direct importance to decision-makers in the resources industry. The Federal Government is responsible also under the Constitution for external trade matters; and international trade and commodity matters are increasingly important in Australia's international relationships. Foreign investment is another area where the Federal Government has a role to ensure that national interests are protected. This foreign investment power flows from the Federal Government's control of foreign exchange movements into and out of Australia. However, before enlarging on these and others of the Federal Government's powers and policies, it should be emphasized that the State governments, by virtue of their wide powers to regulate matters within their own boundaries, are more directly involved in the day-to-day administration and regulation of mining operations. For instance, the powers of the State governments include the responsibility-for the granting of exploration rights and mining leases, the approval of mining operations and the levying of royalties and other like charges. Administrative arrangements covering the granting of minerals and petroleum exploration and development titles vary from State to State. Before development rights are granted, State governments consider environment protection and rehabilitation aspects of development proposals. The provision of infrastructure within State borders is a matter primarily of State government responsibility. It is usual practice in Australia for State governments to construct and operate infrastructure services such. as railways, ports and electricity generation and transmission. The States may also provide certain public services such as electricity. and water, port and loading facilities, communications, health and education services which form part of the infrastructure of mining operations. In remote areas the mining companies themselves usually are expected to provide much of this infrastructure. However, the Federal Government is primarily responsible in some fields, such as telecommunications and parts of the railways network. State governments carry out preliminary exploration and geological mapping and some are directly involved in the mining of coal for power generation. The Federal Government's responsibilities in addition to economic management, taxation, international relations, foreign capital and investment, include regulation of exports, environmental matters and matters affecting the Aboriginals of the Northern Territory. FEDERAL GOVERNMENT POLICIES The continued sound development of the minerals and energy resources sector is regarded by the Federal Government as being of very great importance. However, the Government does not seek to participate directly in resource developments. It sees its role rather as that of establishing a sound economic and policy climate in which private companies can identify opportunities, seek out customers and marshall the necessary capital for the development of resource projects.

Jan 1, 1982

By E. T. Turkdogan, W. L. Worrell

The rate of reaction of hydrogen sulfide with ferrous sulfide was studied by measuring the initial rates of sulfidation of iron strips in hydrogen sulfide-hydrogen-argon mixtures at 670°, 800°, and 900" C. The time-dependent surface sulfur activity is derived from the instantaneous rate of sulfidation with the assumption that diffusion in the sulfide layer is in a pseudo-steady state with the gas-sulfide chemical reaction. The rate of sulfur transfer from hydrogen sulfide to the surface of iron sulfide is proportional to the partial pressure of hydrogen sulfide and inversely proportional to the activity of sulfur at the surface of the sulfide layer. The derived rate equation is based on the assumption that most of the surface sites on the chemisorbed layer of iron sulfide are occupied by sulfur atoms and that the slow rate-controlling reaction is the dissociation of hydrogen sulfide on the chemisorbed layer. The experimental results are in reasonable accord with this reaction model. 1 HE slow approach to parabolic growth rate in the sulfidation of iron in hydrogen sulfide-hydrogen mixtures is a manifestation of slow approach to surface equilibrium between the gas and the surface of the sulfide layer. For example, at 800°C and Fig. 7 in Part I, the parabolic growth rate begins after approximately 1 day of sulfidation time. With decreasing temperature and decreasing partial pressure of hydrogen sulfide, the time necessary to reach gas-sulfide surface equilibrium is much longer. These observations are similar to those reported previously by Turkdogan et al.' on the oxidation of iron to wustite in hydrogen-water vapor mixtures. The slow approach to gas-sulfide equilibrium is well-demonstrated by the results in Fig. 1 where the square of the weight gain per unit area, ( g S per sq cmI2, is plotted against time for gas mixtures having PH g//>H = 1.0 with 0, 25, 50, and 67 pct Ar at 800°C. The value of 1.5 X lo-' (g S per sq cm)' corresponds to almost complete sulfidation of the iron strip (- 0.05 cm thick) to iron sulfide. The points fall on S-shaped curves. If the inflection parts of the curves are considered to be linear, thus indicating parabolic growth rate and the establishment of gas-sulfide equilibrium, their slopes would have to be the same for a fixed ratio in the gas mixture. Such is not the case, and the slopes for the "linear" parts of the S-shaped curves are lower than the value when gas-sulfide surface equilibrium is established. The subject matter of this paper is the kinetics of the surface reaction of hydrogen sulfide with iron sulfide during the early stages of sulfidation of an iron strip. EXPERIMENTAL RESULTS The apparatus and materials used were the same as those discussed in Part I. In the present experiments of relatively short duration, a purified iron strip, 5 by 2 by 0.05 cm, which was suspended in the uniform hot zone of a vertical zircon tube, reacted with a flowing gas mixture of hydrogen sulfide-hydrogen-argon. The sample was suspended from a gold chain attached to a calibrated silica spring. The amount of sulfur picked up by the iron, which formed a layer of iron sulfide, was determined by measuring the displacement of a reference point on the silica spring, using a cathetom-eter. In all cases, the degreased sample was first annealed in a stream of oxygen-free dry hydrogen for several hours to remove any impurities such as oxygen, nitrogen, or carbon which might have been present on the surface of the sample.' The rate measurements were carried out at 670°, 800°, and 900° C in hydrogen sulfide-hydrogen-argon mixtures with pH2 s/Ph2 ratios from 4 to 0.1. In a few experiments of short duration no sulfur deposition was observed in gas mixtures with (comments concerning sulfur deposition at high pH s/ph ratios were made in Part I.) Typical examples of the results obtained are shown in Fig. 2 for two temperatures and two gas compositions. With the present experimental technique, reproducible rate data could be obtained only after a uniform

Jan 1, 1969