Search Documents

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By Mark Sheppard

DURING the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the over- burden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semi- circle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and 800 ft. of 4-in. spiral steel flanged pipe. The connection from the pump

Jan 1, 1938

By A. J. Boynton

THIS paper is not the result of recent research with regard to any particular feature of iron metallurgy, blast-furnace practice or mechanical engineering. It is rather a series of notes with regard to contemporaneous progress in blast-furnace construction and operation, together with some suggestions as to changes and improvements that seem to be desirable. On April 1, 1930, a committee of the Chicago District Blast Furnace and Coke Association presented to that association a rather ambitious study of blast-furnace equipment, together with recommendations for the design of construction of a complete blast-furnace unit for the production of 1000 tons of pig iron per day. This report represented the result of months of study by members of the committee, all of whom were actively engaged in operation or design of blast-furnace plants. It is natural, therefore, that comments on the present state of the art should take this 1000-tons furnace, as recommended by the Association, as a basis for comparison with corresponding features of construction or design. See Table 1. In looking through this report at the present time, the significant difference is in the nature of the gas-washing equipment that today would be specified. In other respects, the installation would remain generally very much as it was outlined in 1930. The change in furnace dimensions would be very slight and of no especial significance, except with respect to changes in stock-line diameter, of which more will be said hereafter. The high-efficiency stove as developed by various designers is thoroughly described within this report, and few changes have taken place since. Blowing equipment shows refinement and reflects the improvement in steam engineering. Hoisting and charging equipment and ladles for the conveyance of iron and slag remain, in general, as they were in 1930. In accordance with a general tendency

Jan 1, 1935

By A. Manganwidjoyo, W. A. Wiebenga

The aim of this paper is to disclose some of the correlations between rock parameters, hidden in Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks," 1956. The empirical relations concern dry rocks of varying porosity. Curves and equations interrelating the specific gravity, compressive strength, bar velocity, and Poisson's ratio are presented. In 1956 Wuerker published his "Annotated Tables of Strength and Elastic Properties of Rock", in which various physical properties of rocks determined by different authorities, are tabulated systematically. The tables are primarily intended for use by mining-, quarrying- and ore-dressing engineers. Since the list of measured parameters for each type of rock includes properties such as — grain size, specific gravity, porosity, compressive strength, static elastic cons:ants (moduli of elasticity, rigidity, specific damping capacity and longitudinal bar velocity) the tables are also of considerable interest to the practical geophysicist. Correlations between rock parameters may enable geophysicists, geologists and civil engineers to transiate measurements from one parameter to another. Even if these translations are of limited accuracy, or valid only within certain specified ranges, they often serve a useful parpose. The aim of this paper is to disclose some of the correlations between rock parameters concealed in wuerker's Tables. Throughout this paper the following symbols and units are used unless otherwise stated: Sg is Specific gravity, the ratio of the density of a specimen to the density of water at 4°C. P is Porosity, in %, the ratio of the volume of voids in a specimen to its total volume. CS is Compressive strength in 1000 p.s.i., the stress under which a specimen will fracture when undergoing a standard compression test. V is Bar Velocity in kilo-feet/sec, the velocity of longitudinal seismic waves measured in a slender bar type specimen. Vc is Bulk or Constraint Velocity in kilo-feet/ sec, the velocity of longitudinal seismic waves measured in a very large specimen.+is Reciprocai bar velocity in millisecs/ft (1 millisec = 10-3 sec). cis Poisson's ratio, the ratio of the lateral to longitudinal strain of a body under longitudinal stress. CORRELATIONS Specific Gravity (Sg) vs. Porosity (P) Figure 1 is a diagram illustrating the relatiooship between specific gravity and porosity for approuirr~ately 70 samples of dry rocks. A curve fitted by estimation to this data yields the empirical formula: Sg =-0.0268P + 2.67 * 0.2 (1) Considering unit volume of a porogs specimen then

Jan 1, 1961

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definite life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital write-offs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral property possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulfur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. Present Value of a Mineral Property In essence the present value of a mineral property is a sum of money in today's dollars that future income from the property are worth. It differs from the total anticipated earnings by the amount of the interest that the unrecouped investment could be expected to earn during the period of recoupment. Thus, if one could accurately estimate what a mineral property will earn during its life, after deducting all operating, administrative, capital, interest, and tax charges, the determination of present value would be a relatively simple mathematical calculation. Normally, where the expected life of the mineral property extends beyond 20 or 25 years, the discounted value of earnings beyond this period is relatively small. The petroleum industry generally discounts the annual cash flow of an operation rather than earnings since, for tax-saving purposes, earnings are kept

Jan 1, 1976

By S. Weinig, J. Winter

The grain boundary adsorption of solutes as a function of bulk concentration and solution temperature was studied using internal-frictimz techniques. From the variation of the cor-responding energy of activation for the Phenomenon, the inter-actior2 energy between a solute atom and a high-angle boundary was calculated. Interaction energies in the range of 0.3 ev were obtained, and were used to obtain the actual concentration of solute at the grain boundary. In corroboralory creel, studies the direct grain boundary contribution to the total creep strain was measured. It was found that the interface creep varied with the type and magnitude of the solute adsorbed. Subscribing to the theory of their being energetically favorable sites at the grain boundary for solutes of both Positive and negative size deviations, ternaries were investigated in Which solutes of both types were present. A marked increase in the resistance to grain boundary creep was manifested. THE major difficulty which has been encountered in investigations of the grain boundary segregation of solutes has been the lack of a sufficiently sensitive method of measuring the amount of adsorbed solute at the boundary. For the general case of a high-angle boundary, no direct method of measuring the adsorption at the boundary has been found to date. Internal friction has been used in several studies of grain boundary adsorption1-3 and although it is somewhat indirect, it was demonstrated to have the necessary sensitivity. In this investigation the authors have used internal-friction techniques in conjunction with a study of the grain boundary contribution to the total creep strain. As both parts of the investigation were performed on the same specimens it was possible to combine a highly sensitive technique with a somewhat more direct method in order to obtain information about the adsorption phenomenon. From internal-friction studies the rate of increase of the activation energy was observed to be a function of the difference in size between the solute and solvent atoms. It was proposed that if Gibbs' adsorption isotherm is considered, i.e., where r is the excess solute at the boundary, c is the bulk concentration, and ay/ac is the change in grain boundary energy with bulk concentration, then AH b/ac must vary in the same way as ay/ac and therefore In this way a relative measure of the grain boundary adsorption of solutes is directly obtainable from in-ternal-friction studies. If the previous work in the field of grain boundary adsorption of solutes is examined, certain apparent information is desirable if the phenomenon is to be understood. The most important questions that must be asked are as follows: 1) Is the adsorption of solutes at the grain boundary an equilibrium process? 2) Can the Mott model of the grain boundary be used as a basis of setting up an elastic interaction between the grain boundary and solute atoms? 3) Is it possible to obtain an exact measure of the excess solute at the grain boundary as a function of temperature and bulk concentration rather than merely a relative measure of the adsorption 4) Are the conclusions obtained from an indirect method such as internal-friction studies meaningful in considering gross grain boundary effects such as creep? EXPERIMENTAL PROCEDURE The material used in this investigation was Bureau of Mines "superpurity" titanium (79 Bhn—1500 kg

Jan 1, 1960

By Henry Lloyd Smyth, J. Ralph Finlay

The most important area of the so-called Keewatin rocks of northern Minnesota is that which runs westerly from Lake Saganaga, near the national boundary, and finally disappears beneath the drift (or has not been farther traced), in the neighborhood of Vermilion Lake. With this belt we have a general acquaintance, extending back some four years. During the past year we have had the opportunity of studying in considerable detail a small part of it, embracing an area of about 12 square miles on the south and east shores of Vermilion Lake. In this paper we desire to record our observations and conclusions, which seem to us important. II.—Literature. Outside the Minnesota Geological Survey, the list of the investigators who have studied the geology of the Vermilion Lake area is not long. Whittlesey, in 1876,* mentioned the occurrence, in the area about Vermilion Lake, of rocks resembling the Canadian Laurentian. Chester,? in 1884, described the iron-ore at Vermilion Lake as occurring in connection with jasper and quartzite, intimately bedded with the country-rock, chiefly sericite schist, and standing in a nearly vertical attitude. The Vermilion iron-bearing rocks, and those of the Mesabi range, he says, are of the same age.

Jan 1, 1896

By C. A. Hansen

The furnace used for experimental work is shown in Fig. 1. One fireclay sagger, or pot, was set within another and the space between the two filled with Silox heat insulation. The hearth is a cast-iron plate with an imbedded ribbon of nichrome wire; this wire heater is connected to a potential regulator, which permits a very close voltage control. A mechanically driven arm is fitted with rabble blades so arranged that a uniformly thick ore bed may be maintained indefinitely. This arm is usually driven at about one revolution per minute but its speed of rotation can be varied as desired. Compressed air is led into the furnace through a meter, and it was found necessary to preheat the air in order to secure the definitely isothermal conditions sought. With this arrangement, it is possible to maintain any desired temperature constant within about 5" C. for any desired length of time and to

Jan 1, 1921

By J. W. H. Clare

An equilibrium isotherm at 550°C is given for ternary alloys rich in aluminum containing 0 to 15 wt pct Cr and 0 to 20 wt pct Mn. Phases encountered are: aluminum solid solution; stable temary compound G; and MnAl8,. In addition, a limited number of alloys were annealed at 450°C to check for differences from the 550°C isotherm. These experiments limited the composition of the G phase at 550°C and further experiments established that the G Dhase is not stable above 590 ± 1 °C. RAYNOR and Little1 established several equilibrium isotherms using aluminum-rich alloys containing up to 5 pct of the elements chromium and manganese. These isotherms showed that, in addition to an a solid solution and the two binary intermediate compounds 8 and MnAl6, a stable ternary compound ex-isted in the system. This phase was called the G phase because of its ghostly appearance in micro-sections. Little, Raynor, and Hume-Rothery2 found a similar phase in binary aluminum-manganese alloys and, as a result of their experiments, concluded that the G phase was a metastable phase existing in the aluminum-manganese system. This phase was stabilized by the addition of chromium. The constitutional work of Raynor and Little,' although showing the existence of the G phase in the aluminum-chromium-manganese system, did not establish precisely the composition limits of the phase or the temperature above which the phase became unstable and disappeared from the system. The work described in this paper was undertaken to provide this information. An examination of the previous work' showed that an isotherm at 550°C would provide the required data regarding composition in the shortest possible time, as the (a + G) phase field narrows considerably at higher temperatures. The same work showed that the G phase ceased to exist between 580° and 595°C. A more precise estimate of the transformation temperature would therefore be obtained by annealing selected alloys at successively higher temperatures beginning at 580°C. EXPERIMENTAL PROCEDURE 1) Materials Used—The experimental alloys were prepared from four master alloys containing 15.00 w pct Cr, 15.28 wt pct Cr, 19.80 wt pct Mn, and 19.38 wt pct Mn which were made from super-purity aluminum, electrolytic chromium, and electrolytic manganese. The aluminum was of 99.996 pct purity, the principal impurities being copper, iron, and silicon. The chromium and manganese were 99.9 pct pure, the principal impurities being antimony, calcium, and magnesium. 2) Preparation of the Experimental Alloys—The alloys were prepared in 20-g quantities by melting together the requisite amounts of master alloy and aluminum in an alumina-lined crucible and, after thorough stirring with an alumina rod, cast into a cold copper mold to give ingots 1/4 in. in diam and 3 in. in length.

Jan 1, 1960

By Laurence Pellier

Electron microscopical studies were made of the effect of sensitization at 1200oF on a Type-.104 stainless steel with high carbon and low nitrogen and oxygen contents, after solution annealing and after cold working. The loci of the carbide precipitates in the early stages of sensitization were followed in dry stripped plastic replicas. Some observations were made by direct electron transmission on thinned films. Intragranular dislocations showed a high degree of stability through the annealing necessary to produce sensitization. I HE present work was undertaken to determine the effect of sensitization, at 1200°F, for 1/2 hr, on the electron microstructure of a Type-304 stainless steel with high carbon, and low nitrogen and oxygen contents, after solution annealing and after cold working. Many electron microscopical studies of sensitization of 18-8 stainless steels have already been made. Most of them utilized extraction replicas, from which the morphology and composition of the precipitated carbides could be established.'-" ry stripped replicas were seldom used for such studies, although it was demonstrated that they are applicable, in general, to EurveYs of the general microstructure of many alloys' and, in particular, to the observation of precipitated carbides in austenitic stainless steels.3

Jan 1, 1963

The First Conference of the Powder Metallurgy Committee convened in the East Foyer of the Hotel Waldorf-Astoria, New York City, at 9:45 a.m., on Feb. 21, 1944, Mr. John Wulff, General Chairman, presiding. THE CHAIRMAN.-In behalf of the American Institute of Mining and Metallurgical Engineers I welcome all members and guests to this conference on Powder Metallurgy. We hope that this meeting will give expert and novice in the field a chance for discussion. Unfortunately, the subject has been overemphasized by some, and, of late, severely criticized by others. We have here today powder producers, fabricators, and engineers of different viewpoints, who can make the meeting a success. Such success depends not only on the caliber of the papers presented but more so on the discussion. To give you time for a free exchange of views, the papers have been shortened purposely. With the hope that you will all benefit by this conference, I shall turn the meeting over to the Chairmen of the morning session, Mr. Roland P. Koehring, of Moraine Products Division of General Motors, and Dr. R. K. Waring, of the New Jersey Zinc Company. SESSION ON DESIGN FACTORS IN POWDER METALLURGY R. P. Koehring and R. K. Waring presiding The opening paper of the session was presented by Mr. Fred P. Peters, as follows:

Jan 1, 1945

By Robert M. Grogan

Fluorspar is the commercial name for fluorite, which is the mineral having the composition CaF2, calcium fluoride. Its valuable properties are due to its content of fluorine, and it is the only important commercial source of that element. The name is derived from the Latin fluere, to flow, because the mineral melts easily and is a good flux. History The mineral has been known since Greek and Roman times, when it was used for drinking cups and ornamental slabs. Various peoples including the Chinese and the American Indians have carved ornaments from large crystals. Its usefulness as a flux was known to Agricola, who wrote about it in 1546.1 Mining began in England about 1775 15 and at various places in the United States during the period 1820 to 1840.28 Substantial production was achieved first in the period 1888 to 1900 in consequence of the development and widespread adoption of the basic open hearth method of making steel, in which fluorspar is used as a flux. After that, production and usage was stimulated by growth in the steel, aluminum, chemical, and ceramic industries and accelerated by World Wars I and II. The organic fluorides called "Freons" entered the picture in 1931, and the use of anhydrous HF as a catalyst in the manufacture of alkylate for high octane fuel blends began in 1942. The development of the froth flotation process in the late 1920's, a differential flotation scheme for separating fluorspar from galena, sphalerite, and other minerals in the 1930's, and the application of heavy-media concentrating methods to the treatment of low-grade ores in the 1940's were outstanding technological contributions that enabled increased production of fluorspar concentrates. Composition and Properties Fluorite in its purest form contains 51.1 pct calcium and 48.9 pct fluorine. Substitution of small percentages of cerium and yttrium for calcium have been noted.4 Mechanical inclusions of gases and fluids such as petroleum and water, and of other solid minerals such as pyrite, marcasite, and chalcopyrite are common. The fluorspar of commerce contains attached and admixed mineral impurities, chiefly calcite, quartz, barite, celestite, and various sulfides. It is interesting that the purest commercial form in which the mineral is sold, acid grade concentrate, contains a minimum of 97 pct CaF2, and as such is of comparable purity to many reagents used in chemical laboratories. Fluorite has a marked tendency to occur in large, well-formed crystals sometimes six to ten inches on a side. It crystallizes in the isometric system, frequently forming cubic and octahedral crystals or combinations thereof. The mineral also occurs in massive and in earthy forms, and in crusts or globular aggregates with radial fibrous texture. Crystalline fluorspar exhibits a great array of colors, from colorless and water clear to yellow, blue, purple, green, rose, red, bluish and purplish black, and brown. The colors are often arranged in alternating bands parallel to cube faces. They may be altered by exposure to X-rays, heat, ultraviolet light, and pressure, and are caused by a variety of factors including the presence of trace impurities and displaced ions in the lattice. Sometimes the changes induced by X-rays can be reversed by ultraviolet radiation. The mineral has a hardness of 4, and is the model of that hardness on the Mobs scale.

Jan 1, 1960

By J. W. Stewart

THE aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula. Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I), It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the I5 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year. PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1941

By WALTER B. JONES

IN ALABAMA there are three distinct groups of bauxite deposits, as follows: (1) Cambro-Ordovician contact with the principal-deposits located in Talla-dega, Calhoun, DeKalb, and Cherokee Counties, and in adjacent portions of the State of Georgia. (2) Midway-Nanafalia contact, with the principal deposits in Barbour and Henry Counties, and in adjacent portions of Georgia; also in North-eastern Mississippi. (3) Mississippian - Cretaceous contact, with a group of deposits centered around Margerum in Colbert County. For the purpose of more clearly describing bauxite mining in the state, past, present and possible future, these three groups will be described separately.

Jan 1, 1934

By D. O. Hobson, J. O. Stiegler, C. J. McHargue

The effects of alloy composition, deformation temperature, heal treatment, ad inlerstilial contamination on the occurrence of deformation twins were studied. The twinning transition temperature varied with composition and was a maximuni of 140°C for the 40 pcl V composition. Tire remperature range of the transition was very narrow. Alloys of 20 to 70 pet V could he cold-rolled and exhibited profuse twinning. The alloys which did not twin at room temperature (10, 80, and 90 pel V) could plot be cold-rolled. Oxygen additions systematically lowered the transition temperatures for all vanadium contents. The transition temperature for a 30 pet V alloy increased with annealing temperature, apparently due to changes in dislocation density and configuration. Twinning did not nucleate fracture in any specimen in the 20 to 60 pet V composition range. THERE is great current interest in the refractory metals and alloys as structural materials. An important factor in considering the ductile-brittle behavior of such materials is the role of mechanical twinning as a deformation mechanism. Mechanical twins have been observed after deformation at low temperatures or at high loading rates in the pure metals iron,1 vanadium,2,3 columbium,4,5 tantalum,6 Chromium,7 molybdenum,8 and tungsten.9 Binary alloys in which mechanical twins have been observed include: iron with silicon,10 phosphorous," or aluminum;12 and chromium, molybdenum, or tungsten with rhenium.13-17 The increase in low-temperature ductility obtained by alloying the Group VI-A elements with rhenium is very important with regard to fabricability, and there has been considerable effort to understand the so-called '(rhenium effect". Factors suggested to explain this effect include:'' 1) increase in solubility of interstitial impurities with alloying (electronic effect): 2) changes in the nature of grain boundary phases; 3) changes in interfacial energies of grain boundaries and stacking faults: and 4) promotion of twinning. Although an outstanding characteristic of these alloys is the profuse twinning that accompanies low-temperature deformation, most studies of the rhenium effect have been concerned with the other factors. During recent studies of refractory-metal alloys, it was noted that solid solutions of columbium and vanadium exhibited high hardness and strength at room temperature and elevated temperature and, surprisingly, also showed considerable ductility at room temperature and below. These alloys deformed by twinning at room temperature when subjected to slow loading rates. It appeared that the low-temperature ductility resulted at least in part from the relaxation of stresses by twinning in a system where slip is difficult. The reason for enhanced twinning behavior in some bee solid-solution alloys is unknown. There have been suggestions18,19 that, as in fee alloys, the

Jan 1, 1965

By Ernest Burchard

A RECONNAISSANCE Of the manganese-and chrome-ore deposits of Cuba was made by the writer, as a representative of the U. S. Geological Survey, in company with Mr. Albert Burch of the Bureau of Mines under instructions of the Secretary of the. Interior, in the Spring of 1918. The object of the study was to obtain authentic information for the use of the United States Government as to the location, character, quantity, and availability of the manganese and chrome-ore deposits in Cuba. Accordingly, the work comprised the examination of such deposits as seemed to be of promise, without regard to stage of development, with a view to determination of the quantity and quality of ore likely to become available for shipment during 1918 and 1919, and of the tonnage of ore in reserve. While it was possible to visit most of the deposits that seemed to be of promise, there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Manganese ore is found in Cuba in Oriente, Santa Clara, and Pinar del Rio Provinces, but in Oriente Province only does it occur in large commercial quantities. There, the deposits are in three areas: one north of Santiago de Cuba, one south of Bayamo and Baire, and one on the Caribbean coast between Torquino Peak and Portillo. In Santa Clara Province, a little ore has been found near the Caribbean coast west of Trinidad; and in Pinar del Rio Province, manganiferous material occurs north of the city of Pinar del Rio and farther west near Mendoza. The manganese ores of Cuba occur, principally, in sedimentary rocks, such as limestone, sandstone, and shale, that are in places metamorphosed, and. in beds that originally may have been water-laid tuff

Jan 3, 1919

By John Chipman, Theodore B. Winkler

IN order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chipman,3 dealt with the simplest possible slag system that would resemble those found in the basic open hearth-the slag system consisting of CaO-MgO-SiO2-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemistry of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, Si02, FeO, Fe203, P205, MnO, A1203 and CaF2, but not all of the slag samples contained all of these components at one time. REVIEW OF LITERATURE Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Brings4' von Samson-Himmelstjerna,5 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution ratios

Jan 1, 1946

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available.

Jan 5, 1927

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman, JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE. Secretary, 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia Holds four sessions during year. Annual meeting in September or October. FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 8, 1915