Search Documents

By B. H. Sage

IN recent years there has been an increase of interest in the flow of gases at relatively high pressures. Hydrodynamic calculation of the energy losses in the flow of gases in conduits, as well as through the porous solid materials constituting natural petroleum reservoirs, requires a knowledge of the viscosity of the fluid at the pressure and temperature involved. Although there are numerous publications concerning the absolute viscosity? of hydrocarbon gases at atmospheric pressure, there appears to be little information available relating to the effect of pressure upon the viscosity of these gases. Vogel28 determined the viscosity of methane at 32° F. and atmospheric pressure. His measurements at 32° F. were later substantiated by the measurements of Rankine and Smith17 at 63° and 212° F. Ishida12 also reported values for the viscosity of methane at atmospheric pressure. Trautz and Kurz26 measured the viscosity of propane at atmospheric pressure, from 83° to 530° F., by the use of a short capillary tube. Rap-penecker18 determined the viscosity of gaseous isopentane at elevated temperatures. Day' made an accurate investigation of the effect of pressure upon the viscosity of n-pentane and isopentane at pressures from 2 lb. per sq. in. ? to the vapor pressure at 77° F. (approximately 9.8 and 13.3 lb. per sq. in., respectively). Earhart5 reported data upon the viscosity of several natural gases measured by the long capillary-tube method. The viscosity of air, at atmospheric pressure and 73.4° F., was measured by Harrington7 by the rotating-cylinder method. Kellstrom13 has recently made an elaborate investigation of the viscosity of air at atmospheric pressure. The latter work is perhaps the most accurate investigation of the viscosity of a gas that has been made. .

Jan 1, 1937

By L. T. Larson

The spectral reflectivity of zirconium in light of 441 to 668 nanometers (nm) wavelengths and air immersion has been determined. Bireflectance and apparent-angle -of-rotation measurements show zirconium to be optically isotropic when examined in light of approximately 484 nm wavelength. There is a direct relationship between bireflectance and the tilt of the basal pole of zirconium from the surface normal. This relationship allows the determination of the spatial orientation of the basal pole of an individual single crystal within a coarse-grained poly crystalline section to within± 2 to 3 deg for angles of basal pole tilt from 0 to 90 deg. In recent years considerable attention has been given to the quantitative determination of optical properties of opaque minerals by use of vertically incident, plane-polarized light. In particular, Cameron' and Cameron et a1.2 have developed criteria for the identification of a large number of anisotropic ore minerals based upon measurement of the apparent angle of rotation and the ellipticity or phase difference of the reflected light. It was shown by Larson and Pickle-simer3 that apparent-angle-of-rotation measurements may also be used to determine crystallographic orientations of grains of noncubic metals. In particular, it was shown that the basa.1 pole orientation in space of zirconium grains can be determined to ±3 deg for those grains with basal pole tilts of 10 to 90 deg from the plane of the section. Another, even more widely studied, optical property is reflectivity. cameron4 has commented upon measurement of the reflectance of plane-polarized, vertically incident light and Bowie and Taylor5 have made such measurements an integral part of their system of ore-mineral identification. Leow6 has reported on the spectral reflectivity of molybdenite and has used reflectivity values to calculate refractive indices and absorption coefficients. Cameron7 has made use of reflectivity values to ascertain aniso-tropic ore mineral symmetry and Piller and v. Gehlen8 have evaluated sources and importance of errors in reflectivity measurements as applied to calculation of optical constants. cambon9 has shown that reflectivity measurements using vertically incident, plane-polarized light are useful in the investigation of metals and in the identification of phases present in alloys. Bronson10 has made preliminary measurements on the optical anisotropy of beryIlium and Mott and Haines11 have published qualitative data on the intensity of light reflected from sections of bismuth, tin, and aluminum when these metals are microscopically examined under crossed polarizing plates. Koritnig12 has correlated the reflectivity of homogeneous solid solutions with their chemical compositions. From the above work and investigations in progress by this author, it is apparent that accurately determined values for the reflectance of vertically incident, plane-polarized monochromatic light from carefully polished surfaces of noncubic metals can prove useful in identification, composition determinations, and crystallographic orientation applications. Finally, reflectivity values, when measured in two media of differing refraction index and related to standards whose spectral reflectivities in these media are known, can be used to calculate optical constants such as refractive index and absorption coefficient. These constants may prove of use to those concerned with problems of electron band configuration. This paper reports the spectral reflectivity of zirconium measured in light of 441 to 668 nanometers (nm) wavelengths and air immersion. It also gives maximum bireflectance values for a prism section of zirconium in these wavelengths and shows how bire-flectance may be used to determine the crystallographic orientation of zirconium single crystals. Because of the lack of information on the reflectivities of the standards in oil immersion, no attempt is made to calculate the refractive indices or absorption coefficients although it is recognized that such values may be of fundamental importance. METHOD Single crystals of zirconium were cut by electro-discharge machining from a single-crystal rod grown from iodide bar by an electron-beam zone-melting process.13 The crystal sections were mounted in cold-setting epoxy resin and mechanically polished to a plane, uniform, bright surface. Each crystal was then chemically polished in a 26/26/43/5 mixture (by vol) of water, nitric, lactic, and hydrofluoric acids to remove the mechanically damaged and smeared surface layer. Final polish was obtained by electropolishing at 30 v in a bath of methyl alcohol and perchloric acid (98/2 by vol) at -70oc.14 Reflectivity measurements were made using a photometer system designed and developed at Oak Ridge National Laboratory and described in detail by Larson.15 Briefly, the reflectivity measuring system consists of a reflecting microscope; a double-beam, null-balancing photometer array; a mechanically driven microscope stage; and a direct X-Y readout of the reflectivity of the specimen relative to its orientation on the microscope stage. The measuring photometer receives its signal from the specimen through a slotted Wright occular placed on top of the photovisual head of the microscope. The reference photometer receives light through a flexible glass "light pipe" from a mirror in the reflecting system of the microscope. Monochromatic light is attained through use of interference filters (15-nm half-peak width pass bands) placed in front of a stabilized Vickers 12 v, 100 w, tungsten-filament, quartz-iodide lamp.

Jan 1, 1970

By P. Barnes

The sums given in the accompanying table are those actually paid for material and labor up to about August, 1875; but, as some parts of the machinery were not wholly completed at the starting of the works in September, 1875, the statement cannot be taken as an absolutely correct note of the total cost. A complete description, with engravings of the building and machinery, was given in Engineering, April 26th, 1878, in a paper by Messrs. A. L. Holley and Lenox Smith, to which convenient reference may be made. A detailed list of the construction accounts has been given in a paper, by the present writer, in vol. vi, Transactions of the Institute. A summary is given in the table of the items in each class which enter into the total cost, and also a note of the proportion which each of these items forms of the whole. A concise view may thus he obtained of the facts embodied in the statement as a whole, even though it cannot lay claim to completeness in showing the entire or final cost. An urgent suggestion has reached the writer from a distant country that such statements of cost to be really most serviceable should give the details in days of labor, in weight of iron, and in number of brick, and to this an assent is most cordially yielded. It is true, however, that the mere labor of copying arid compiling these details to such a degree of minuteness, would be very great, and, in any event, the probable difference between the plans of an existing establishment and one projected, would be so wide as to render even so complete a statement of cost of little more real service than the approximate notes given herewith.

Jan 1, 1879

By P. Barnes

THE sums given in the accompanying table are those actually paid for material and labor up to about August, 1875; but, as some parts of the machinery were not wholly completed at the starting of the works in September, 1875, the statement cannot be taken as an absolutely correct note of the total cost. A complete description, with engravings of the building and machinery, was given in Engineering, April 26th, 1878, in a paper by Messrs. A. L. Holley and Lenox Smith, to which convenient reference may be made. A detailed list of the construction accounts has been given in a paper, by the present writer, in vol. vi, Transactions of the Institute. A summary is given in the table of the items in each class which enter into the total cost, and also a note of the proportion which each of these items forms of the whole. A concise view may thus be obtained of the facts embodied in the statement, as a whole, even though it cannot lay claim to completeness in showing the entire or final cost. An urgent suggestion has reached the writer from a distant country that such statements of cost to be really most serviceable should give the details in days of labor, in weight of iron, and in number of brick, and to this an assent is most cordially yielded. It is true, however, that the mere labor of copying and compiling these details to such a degree of minuteness, would be very great, and, in any event, the probable difference between the plans of an existing establishment and one projected, would be so wide as to render even so complete a statement of cost of little more real service than the approximate notes given herewith.

Jan 1, 1879

By J. M. Sands

Describes important developments in, four counties, all of which brought in 40° oil. Indications are favorable for the future, although the daily production of the agate decreased 19,000 bbl. during the year 1923. THE state of Kansas had a daily average crude-oil production of about 87,000 bbl. at the beginning of the year. This showed a steady but consistent decline during the 12 months, so that the daily average production at the end of the year was slightly over 68,000 barrels. GREENWOOD COUNTY THE most active development in Kansas during the year was in Green-. wood County, in a line from near Sallyards in T 25-R 9 to east of Madison in T 22-R, 11. The main part of. this development has been in a succession of pools beginning at the south with the Polhamus pool in 34-24-9 and 3 and 4-25-9; Thrall pool in 28, 29, 32 and 33-23-10; Burkett pool in. 13, 23, 24 and 26-23-10; Seeley and Wick pool in 22, 27, 28, 32 and 33-22-11 and 5, 6, 7, and 8-23-11; Frohm pool in 11, 14 and 15-22-11; Madison pool in 31 and 32-21-12 and 6, 22, 12 and 1-22-11. Some of these pools, have two or more sands, locally called Bartlesville and Burgess Sands. They range in. depth from 1850 ft. near Madison to 2450 ft. near Sallyards, the general dip being to the west. The thickness of these sands runs from 20 to 100 ft., the initial production of the wells being 50 to 1000 bbl. of 40-gravity oil or better.

Jan 3, 1924

By E. A. Cappelen Smith

FOR distinguished service in the art of hydrometallurgy, the Mining and Metallurgical Society of America presented its gold medal to E. A. Cappelen Smith, at a dinner held in the Hotel Commodore, New York, on Nov.' 10, 1920. Prof. Waldemar Lindgren, president of the society, in giving the medal, said: "By the advancement of the science of hydrometallurgy, by the construction of plants on a scale audacious in their conception, by the successful overcoming of all sorts of difficulties, you have placed your name among those who occupy the very front rank among the hydrometallurgists. In recognition of this distinguished contribution to the science of metallurgy, the Mining and Metallurgical Society of America now awards you its gold medal."

Jan 1, 1920

By GUY B. HUNNER

THOSE magnetite ore bodies comprising the Clifton Mines are situated in the south central part of St. Lawrence County, New York, on the western slope of the Adirondack Mountains. The topography is made up of gently rolling hills densely wooded with second-growth maple, birch, and hemlock. Drainage is north and west to the St. Lawrence River.

Jan 1, 1943

Discussion of the paper Of JAMES JOHNSTON, presented at the New York meeting, February, 1914, and printed in Bulletin No. 85, January, 1914, pp. 107 to 133. CHAIRMAN E. GIBBON SPILSBURY.-I would like to call attention to the fact shown in this paper that less than five years or perhaps seven years ago nobody had thought it possible to cyanide with success silver ores. The cyaniding of silver and gold ores was first of all started in Mexico, and gradually extended to this country in the case of the silver ores alone. The average extraction, I think, for the metals in Mexico, in the case of the silver ore, is less than 85 per cent., whereas here, in the case of a very complex ore, carrying a high percentage of sulphur and arsenic, and other objectionable elements, the ore has been treated so as to extract an average of 95 per cent. of the silver contents of the ore. It is really a phenomenal revolution in the metallurgy of silver ores which has been demonstrated and worked out at the Nipissing mines. GEORGE A. PACKARD, Boston, Mass.-I would like to suggest a slight modification, perhaps, of the statement which is made that no one considered cyaniding of silver ores up to five, or perhaps seven years ago, because in 1897, when I was at Mercur, Utah, one mill near there was operating on silver ores. It did not operate very successfully from a commercial standpoint, because they did not have a great deal of ore, but the extraction, I was told, was very satisfactory, and I am quite confident that it was, because, as suggested by the name, Chloride Point, the ores were silver chloride ores, and of course very easily soluble. Some years before that, in 1892, I made some tests myself. I spent three months making tests on more or less complex silver sulphide ores at Virginia City, Mont., and while our tests on the plain sulphide ores, finely ground, were quite successful, on account of the presence of a small amount of copper we did not work out a satisfactory solution of the problem at that time; although since then a cyanide plant has been erected and for at least eight years these ores have been treated by cyaniding at Virginia City, and the mill is still in operation. The period of five to seven years should, therefore, be modified considerably, in justice to the pioneers in the cyanide processes. REGINALD E. HORE, Toronto, Ont., Canada.-I hoped that there would be metallurgists from Cobalt here to present and discuss Mr. Johnston's paper. In their absence a few remarks from me may help to make clearer to you what they have accomplished.

Jan 6, 1914

By C. E. Birchenall, W. Batz, H. W. Mean

AT temperatures between 1095' and 1347ºC, 13 runs have been made on the diffusion of silicon in iron. In two of the runs the couple compositions were entirely within the loop of the Fe-Si system; the base alloys contained 0.0 and 1.0 wt pct Si. The other runs in which the couples consisted of a 2.3 wt pct Si alloy welded to a 3.7 pct Si alloy were a phase throughout. The alloys were made by melting electrolytic iron and commercially pure silicon. Trace impurities were not determined. The butt welded couples were diffused in an inert atmosphere of argon or hydrogen. After cooling, cuts of two mils or greater thickness were machined parallel to the weld interface. The chips were analyzed for silicon. When the concentration and distance data were examined on the conventional probability plot,' no marked variation of the diffusion coefficient with concentration was indicated over the narrow composition ranges employed. Therefore, a single diffusion coefficient is recorded for each run in Table I. The temperatures and atmospheres of the diffusion anneal are listed along with the compositions of the base alloys. For a iron the silicon diffusion coefficient is given by the equation: D = 0.44 e-48,000/RT where R is the gas Constant and T, the absolute temperature. However, since the scatter in the data is fairly large, the activation energy may be in error by as much as 6000 cal per g-atom. The two ? iron points do not permit estimation of the activation energy with any reasonable certainty. They do indicate that the coefficients reported by Smithells2 and Jost,3 based on the work of Fry,4 are much too high. Although very dilute solutions in iron of manganese,5 nickel,8 cobalt,7 and molybdenum8 give dif- fusion coefficients quite close to those obtained for self-diffusion in iron, the silicon values are considerably higher, though of the same order of magnitude. This seems to be consistent with the fact that the silicon atom is the only one of those listed here which is appreciably smaller than iron. The authors are grateful to the Office of Naval Research for their support of this work under Contract N6ori-47, Task order IV, Project NR 031-184, to J. K. Stanley and the Westinghouse Research Laboratories for the silicon alloys used, to several steel companies for the silicon analyses, and to C. Wells, of the Metals Research Laboratory, Carnegie Institute of Technology, for numerous suggestions during the course of the work. References 'C. Wells: Atom Movements (1951) Chapter 2. A.S.M. 2C. J. Smithells: Metals Reference Book (1949) p. 405. Interscience. Pub. Co. 3W. Jost: Diffusion (1952) p. 223. Academic Press. 4 A. Fry: Stahl und Eisen (1923) 43, p. 1039. T. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 315. "C. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 329. 7M. F. Hawkes and R. F. Mehl: Trans. AIME (1947) 172, p. 467; Metals Technology (August 1947). .J. L. Ham: Trans. A.S.M. (1945) 35, p. 331.

Jan 1, 1953

By J. G. Thompson

PROJECT 8411 of the U. S. Bureau of Standards, sponsored by the Iron and Steel Division of the A.I.M.E., is an attempt to define more concisely than has been possible heretofore the accuracy and the Limits ' of usefulness of the ' various methods now in use for the determination of oxygen as it exists in ferrous materials. It originated in correspondence between John Johnston and other metallurgists, and was brought to the attention of the Iron and Steel Division of the Institute at the Annual Meeting in February, 1933. As reported in MINING AND MET,ALLURGY, Vol. 14, page 152, March, 1933, "Dr. Johnston introduced, and those present adopted, a resolution that the Iron and Steel Division of the A.I.M.E., believing that a careful comparison of the several methods now in use for the analysis of steel for nonmetallic elements such as oxygen is highly desirable, heartily endorses the proposal that the U. S. Bureau of Standards act as a clearing house " in this matter, undertaking the final preparation and allocation of identical samples to those laboratories willing to collaborate in this important question, and collate the results re- ported back to the Bureau.'"

Jan 1, 1934

By L. O. Howard

WHAT was perhaps the first attempt at basic converting in the Southwest was made by the late Charles F. Shelby at Cananea early in 1907, when he removed the acid lining from one of the 8 by 12-ft. barrel-type converters then in use at the reduction works of the Cananea Consolidated Copper Co. and substituted a lining of one course of magnesite brick. In this shell, he blew 21 taps (about 180 tons) of matte to white metal before the brick gave out along the tuyère line. In every case, the white metal so made was transferred and blown to copper in other converters. The cost of the lining was $700 and Mr. Shelby gave up the experiment as impracticable. No further serious effort to bessemerize copper mattes in a vessel having a more or less permanent lining of basic brick was made by any of the large copper smelters in the Southwest until some months after Messrs. Peirce and Smith had brought the question permanently before the public, and had proved it to be a metallurgical and financial success by their work at Baltimore and Garfield. Early in 1911, the Cananea Consolidated Copper Co. had in operation at its reduction works at Cananea, Mex., several 8 by 12-ft. barrel-type converters lined with magnesite brick which had previously been operating with acid linings. In the 18 months following, these converters produced 50,000 tons of copper. In June, 1912, this company installed the first of its new equipment of six stands of electrically operated 12-ft. Great Falls type converters, and shortly afterward discontinued the use of the smaller shells. In September, 1911, the Consolidated Kansas City Smelting & Refining Co. had installed at its El Paso plant two 10 by 26-ft. Peirce-Smith converters. Later, in March, 1913, one standard Great Falls type converter was added. .About the time the Peirce-Smith converters were going in at El Paso, the Calumet & Arizona Mining Co. was experimenting with basic linings in 7-ft. by 10-ft. 6-in. barrel converters at its plant in Douglas, Ariz. These efforts were sufficiently successful to enable the plant to handle the total output of copper in these small shells until the standard. Great Falls converters were substituted in June, 1914.

Jan 9, 1916

By R. P. Rothwell

The milling of silver ores has arrived at a great degree of perfection in the mining districts of our Western States and Territories, and I hare thought the record of the practical results obtained at the present time, in a few of the principal districts, would prove of value arid interest to many of our members, both at home and abroad. An American silver mill is composed, in descending order from where the ore is dumped, of: 1st. A rock-breaker, usually of the Blake or Alden pattern; 2d. The battery of stamps, the number of which varies from 5 to 120, generally in batteries of 5 or 10 heads, so arranged that a single battery may stand while the others are running; 3d. The tanks where the crushed ore settles (if it is a met stamping-mill), or of a drying-floor if the crushing is done dry; 4th. Amalgamating pans ; 5th. Settling pans ; 6th. Agitators or pans in which mercury escaping in the tailings is caught; 7th. Blanket sluices, over which the tailings run, and where mercury and unamalgamated sulplides are saved. A reference to the engravings (see plate), which show one of the latest forms of an 80stamp silver-mill run by a turbine water-wheel, will show clearly the arrangement of the several parts. THE ONTARIO, UTAH, SILVER MILL. One of the best examples of a silver-mill, and at the same time one of the most successful concerns in the West, is the mill of the Ontario Silver Mining Company, near Salt Lake, in Utah. This mill treats the ore from the Ontario mine, ore which at present is very base, being composed of zinc, lead, and silver sulphides and silver chloride in a quartz gangue. This ore has become baser as the mine attained greater depth, though the vein holds its own, or rather increases, both in thickness and richness. The mill is managed in a skilful and economical manner, though the necessity for

Jan 1, 1880

By J. C. Branner

(New York Meeting, February, 1012.) DURING the past two or three years I have seen statements regarding the first discovery of fullers' earth in this country that seem to require correction or modification. One appears again in the Mineral Resources of the United States for 1909, part II., p. 738, where it is said that ? fullers' earth was first discovered in the United States at Quincy, Fla., in 1893." In this connection the following bit of unpublished history concerning fullers' earth in the State of Arkansas is worthy of attention. In April, 1891, when I was State Geologist of Arkansas, a Swede named John Olsen, formerly a copper-miner in Michigan, but then living south of Little Rock, brought me a sample of what he thought was fullers' earth. He reported that it was from near the town of Alexander, the locality being 1 S. 13 W., section 8, SW. quarter of the SE. quarter. My chemist, Dr. R. N. Brackett, analyzed the material, and reported: Per Cent. Silica, . . SiO2., . 63.19 Alumina, . AL2O3, . 18.76 Iron, . Fe203 7.05 Lime, . Ca0 0.78 Magnesia, . . MgO 1.68 Potash, . K2O 0.21 Soda, . . Na2O 1.50 Loss on ignition, . 7.57 100.74 Water at 110° to 115° C. = 7.84. Another sample from about the same locality, also brought by John Olsen, on analysis by Dr. Brackett gave

Jul 1, 1912

By L. O. Howard

What was perhaps the first attempt at basic converting in the Southwest was made by the late Charles F. Shelby at Cananea early in 1907, when he removed the acid lining from one of the 8 by 12-ft. barrel-type converters then in use at the reduction works of the Cananea Consolidated Copper Co. and substituted a lining of one course of magnesite brick. In this shell, he blew 21 taps (about 180 tons) of matte to white metal before the brick gave out along the tuyhre line. In every case, the white metal so made was transferred and blown to copper in other converters. The cost of the lining was $700 and Mr. Shelby gave up the experiment as impracticable. No further serious effort to bessemerize copper mattes in a vessel having a more or less permanent lining of basic brick was made by any of the large copper smelters in the Southwest until some months after Messrs. Peirce and Smith had brought the question permanently before the public, and had proved it to be a metallurgical and financial success by their work at Baltimore and Garfield. Early in 1911, the Cananea Consolidated Copper Co. had in operation at its reduction works at Cananea, Mex., several 8 by 12-ft. barrel-type converters lined with magnesite brick which had previously been operating with acid linings. In the 18 months following, these converters produced 50,000 tons of copper. In June, 1912, this company installed the first of its new equipment of six stands of electrically operated 12-ft. Great Palls type converters, and shortly afterward discontinued the use of the smaller shells. In September, 1911, the Consolidated Kansas City Smelting & Refining Co. had installed at its El Paso plant two 10 by 26-ft. Peirce-Smith converters. Later, in March, 1913, one standard Great Falls type converter was added. About the time the Peirce-Smith converters were going in at El Paso, the Calumet & Arizona Mining Co. was experimenting with basic linings in 7-ft. by 10-ft. 6-in. barrel converters at its plant in Douglas, Ariz. These efforts were sufficiently successful to enable the plant to "handle the total output of copper in these small shells until the standard Great Falls converters were substituted in June, .1914.

Jan 1, 1917

By C. W. Davis

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water -by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.1 The properties that make fuller's earth useful in the treatment of petroleum products by "percolation" and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other, adsorbent earths.

Jan 1, 1929

By Tom Westgarth

As papers are placed before you upon large gas-engines in Belgium and Germany, it was considered that some information should be given upon the same subject in Great Britain. I therefore agreed to compile these notes, which I have made very short in view of the somewhat full nature of the other papers presented to this meeting, and considering the complete nature of the many publications which have been made recently upon the subject of large gas-engines. I give below Tables I. to VI., showing the number and particulars of large gas-engines which have been built or are building by British makers, and in view of the growing size of gas-engines I have concluded that engines less than 500 h.p. cannot now be included in the category of large gas-engines, and therefore I have not considered engines under that power.

Nov 1, 1906

By R. C. de Lange

An improved replica technique is developed for a nondestructive study of the nucleation and growth of fatigue cracks. Three different growth stages of a fatigue crack were observed. An initial stage of high growth rate is followed by a long period of very slow growth, until finally a third period of high growth rate leads to fracture. THE metal-fatigue process is of a very complex nature. The experimental approach towards fatigue is susceptible to many minor influences which, together with the unavoidable scatter in testing results, makes the interpretation a matter of extreme care. The generally accepted fact that, in a homogeneous material, the fatigue cracks start at a free surface indicates that surface studies may contri-but in an essential way to a better understanding of the fatigue mechanisms. Indeed metallographic observations of the fatigue phenomena have been very fruitful in the last decade. The study of extrusions, intrusions, and persistent slip bands has contributed much to the present knowledge of the early processes in fatigue.' The drawback of the current metallographic techniques lies in the fact, however, that either observations of fatigue phenomena had to be made in a destructive way after an only partly executed test or a sequence of observations on the same test bar was only possible on notched specimens.2 4 In both cases an uncertainty exists as to the nucleation and growth of the fatigue crack in an unnotched test bar, where the crack can start at any place of a large area and develops in a test bar, which is macroscopically

Jan 1, 1964

By J. H. East, E. R. Maize

Probably no other type of equipment is now being introduced into American underground mines about which less is known and about which there is more misinformation than the Diesel mine locomotive. Any equipment installed underground brings with it hazards that were not present before, and it is the purpose of this paper to show that Diesel-powered equipment can be used with safety in underground mining if certain feasible but very important precautions are taken. Diesel locomotives are not new in underground mining, since they have been used successfully in European mines for at least 19 years, but their use in American mines is exceedingly limited; so far as is known, only five Diesel mine locomotives are operating at present in United States mines. Diesel locomotives were permitted underground in Great Britain for the first time in 1939, and the rapid increase in the number in use in those mines testifies to their safety and efficiency. More than 1300 Diesel mine locomotives are in use in European mines, according to the latest statistics; these locomotives are employed in coal, iron, lead-zinc and mercury mines. SO far as is known, the Diesel mine locomotive has not yet caused an explosion or mine fire, and has not been the cause of any fatalities from toxic gases in the mines in which it has been used. Adjustments of Diesel Engines foR Underground Use A Diesel engine adjusted to work in an underground mine should not be confused with the same engine adjusted for use outside the mine. Adjustment of the air:fuel ratio for engines that are used on the surface is intended to give the maximum fuel economy, and little or no attention is given to the chemical composition of the exhaust gas produced. Many such engines are poorly adjusted and perhaps poorly maintained, with the result that the engine emits smoke in quantity as well as the disagreeable odor familiarly associated with Diesel engines. The air:fuel ratio in the case of Diesel engines operated on the surface is generally around 15:1; that is, 15 lb of air to burn I lb of fuel. Diesel engines adjusted to work underground usually have an air:fuel ratio of about 20:1, as at this ratio the minimum quantity of toxic gases is given off in the engine exhaust. Diesel engines operated underground must be maintained in better condition than similar engines used on the surface; otherwise, the smoke emitted in the exhaust becomes objectionable if not unendurable. Practically normal air is required for safe operation of Diesel engines underground or in confined places; failure to provide virtually normal air for Diesel engine operation is almost certain to result in trouble. Bureau of Mines engineers have determined that the air in which a Dicsel Operates hi confined places should contain less than % pct of carbon dioxide and at least 20 pct of

Jan 1, 1949

By Roy P. Full, Robert M. Grantham

Regional structural adjustments in early Tertiary time resulted in the development of the Republic graben, a major down-dropped block that is from 6 to 10 miles in width and more than fifty miles in length. The graben became the center of extensive volcanic activity during Eocene and Oligocene time, resulting in a thick sequence of water-laid tuffaceous sediments, volcanic flows, and associated intrusives. A younger series of sediments, pyroclastics, and flows were deposited in structural depressions within the graben following the period of widespread volcanic activity. The Republic mining district is located along one of the major intragraben structural zones, where continuing subsidence during the period of volcanic activity resulted in an increased thickness of flows and associated flow breccias and pyroclastics. Intrusive masses in part healed early graben-forming faults, but later subsidence reopened old faults and created new fracture zones which later became the control for the gold-quartz veins. Considerable block adjustment along the subsidence area is evidenced by the structural pattern in the mines, and telescoped vein structures indicate north-south compressional stresses and east-west graben-forming tensional stresses prior to and during the emplacement of the veins. The veins, varying from a few feet to more than 50 feet in width, are filled primarily by fine-grained quartz, commonly chalcedonic or porcelain-like in appearance. Finely laminated dark-gray to black concentric banding within the veins generally distinguishes the better-grade ore zones, which contain finely disseminated sulfides and ore minerals that include principally electrum, stephanite, naumannite, and native silver.

Jan 1, 1968

By W. G. Matteson

The Gulf Coastal plain of the southern United States is that area bordering for a large part, the Gulf of Mexico and extending inland and northward to the main interior highland region. It is more or less V-shaped and includes the States of Florida, extreme southern Alabama, all .of Mississippi and Louisiana, the eastern and southern half of Arkansas, and the eastern, southeastern, and southern portions of Texas. While the contents of this paper apply to. the Gulf Coastal plain in general, they are intended to refer more specifically to that portion of the plain included between the 90th and 97th meridians, and the 29th and 33d parallels, an area that may be described geographically as comprising western Mississippi, all of Louisiana, part of eastern and all of south-eastern Texas. It is within this area that numerous and prolific oil pools have been developed during the last 17 years.

Jan 2, 1918