Search Documents

By Bowang Xiao

Recently more and more attentions are paid to high pressure hydrogen quenching (HPHQ) for its advantages such as environmental friendliness, low distortion, etc, compared to oil and water quenching. In HPHQ process, heat transfer coefficient (HTC) usually varies from part surface to surface because of the intense variation of gas velocity around the part. This article studies the effect of HTC distribution on part distortion after HPHQ and shows that finite element simulations considering HTC distribution predict different distortion from these without considering HTC distribution. It is also pointed out in this article that HTC distribution can be optimized by adjusting part orientation and HPHQ condition so that part distortion is minimized.

Jan 1, 2010

By J. E. Hawley, Y. Rimsaite, T. V. Lord

"IntroductionIN THE COURSE of. a spectrographic investigation of the platinum metal .content of various minerals in sulphide ores, the use of • fire-assay beads dissolved in gold-amalgam ( 1) was found suitable for the quantitative determination of palladium and platinum. Later work on platinum and bismuth-rich beads showed however, that these could not always be readily mixed uniformly in the amalgam. Accordingly another technique was sought which would allow the simultaneous determination of gold, silver, palladium, platinum, rhodium, and bismuth, the last .a common contaminant in fire-assay beads. The method evolved, which consists of dissolving fire-assay •beads in .lead, resembles in several respects the method of Scobie (2) in which silver was used. It has equally good sensitivity arid reproducibility, and allows the determination of silver as well as the other metals mentioned. The 'mutua1 standard' method of calculation (3a) is used to determine actual quantities present. This method has been applied to sulphide and arsenide minerals and •ores• of nickeliferous and non-nickelferous deposits• of both pre-and post Cambrian age, and, following a suggestion by Dr. G. S. Hume and the late Dr. H. V. Ellsworth, Geological Survey of Canada, has also been used for a peculiarly rich platiniferous uranium oxide ore from the Nicholson property, Lake Athakaska, Sask. More recently, the method has been .tested for the determination also of iridium and ruthenium and results indicate it may be applied, as• well to osmium."

Jan 1, 1953

By M. Machikicho, N. R. Shoko, J. Chirasha

Keywords: Pyrometallurgy, furnace, ferrochromium, alloys, Zimbabwe Zimbabwe Alloys was founded in 1949 by a consortium led by the John Brown Group. It was the first ferrochrome plant in Africa. The establishment of the refinery was necessitated by an increase in world stainless steel demand and the need to reduce cost by shipping alloy rather than chrome ore. The location of the refinery in Gweru was influenced by a number of factors, not least of which were the abundance of chrome ore deposits, access to inexpensive power from Kariba, the availability of reductant coke from Hwange, accessibility to ports (as the town was well served with rail and road networks second to none in the country), and of course cheaper labour costs. The production of Low Carbon Ferrochrome (LCFeCr) was commissioned in 1953 and produced from an Open Arc Furnace with a Submerged Arc Furnace producing Ferrosilicon Chrome (FeSiCr) that is used as a reductant in the production of LCFeCr. An experimental furnace was commissioned in 1958 to help with efficiency and control on larger furnaces. A second Submerged Furnace was commissioned in 1963. Three other Submerged Arc Furnaces were built between 1967 and 1974. Several mines were acquired between 1974 and 1984, as a strategic move to ensure the growth of the refinery. A briquetting plant was commissioned in 1977, enabling the use of friable ores to enhance the capacity of ore supplies and ore cost management. A plant to recover alloy from slag was established in 1994 to capitalize on market demand without large capital outlay that would be required to build other furnaces to increase capacity. Zimbabwe Alloys has created employment opportunities throughout the years. There have been direct employment opportunities at both the refinery and the mining divisions. With time, indirect employment was realised both upstream and downstream of the refining process, enhancing the livelihood of numerous people. Zimbabwe Alloys' involvement with various labour skills has, of necessity, enabled it to develop a culture of safety at work, home, and play. Zimbabwe Alloys has contributed to society by participating and funding various local initiatives primarily to impact positively on societal needs. The latest development was in 1996, when Zimbabwe Alloys entered into a Technical Transfer Agreement with Japan Metals and Chemicals to improve the efficiencies and hence the profitability of the LCFeCr production process. A significant quantity of various alloys has been produced since inception, and significant foreign currency has been earned for the country. This was in spite of challenges that included the cyclic nature of market prices, the upheavals of sanctions affecting the macro-economic environment, and the challenges related to the deteriorating grade of chrome ore and reductant coke.

Jan 1, 2006

By James K. Richardson

STATISTICAL evidence shows that continued efforts made by Government and industry to make mining safer during the last two decades have had most favorable results. In the copper-mining industry an accident frequency of 146 per million man-hours worked in 1925 dropped 71 per cent by 1945 to 43. This downward trend was relatively consistent except for a high period in 1937 which was probably due to a resumption of large-scale operation with many untrained miners. The iron-mining industry showed a similar trend, but at the relatively lower accident frequency of 66, which dropped to 24 in 1945. The close relationship between the steel and iron-mining industries may be one reason for the lower accident frequencies, because the steel industry is noted for its greater recognition of the fact that safe working conditions are an important part of labor-management relations.

Jan 1, 1948

By Hellsten KJ, Butt CRM

Major Francis Hamilton Buchanan coined the term `laterite' (Latin; brick-rock) in 1807 for the red earths used for building blocks in southern India. Although these earths were actually weathered basalts, the term is now applied to weathering profiles developed upon a wide range of bedrocks. The Ni-laterites are a special class within the broad laterite family.

Jan 1, 1996

By David A. Hall

We present an analysis of the propagation in a uniform tunnel of semi -circular cross section that contains two axial conductors. In particular, we show that, even if one of these conductors has high ohmic loss, one of the two propagating modes has relatively low attenuation. This corresponds to the situation where an unloaded dedicated wire is used to improve radio frequency communication in a mine tunnel that contains a heavily loaded trolley wire.

Jan 1, 1978

By Kirstin Girdner, Tom BoBo, Brian Norton, John Kemeny

Split Engineering is a truly customer oriented company dedicated to providing quantified fragmentation information of the highest integrity to enable process management and control. Technical decisions, blasting costs, operational efficiency and productivity and equipment performance can all be related to optimum fragmentation. In the past, the lack of an easy, non-disruptive, economical measuring technique has meant that, in most cases, rock fragmentation has not been defined in quantitative terms. Now, the Split-Desktop@ software provides an economical alternative to manual sampling and screening and an objective measure rather than subjective qualitative estimates. This workshop will present the latest features of the Split-Desktop@ software and show users how to quickly get quantifiable results from their blast fragmentation. A step-by-step demonstration will display the software’s flexibility, user-friendly options, and ease of use. Outlining where other mines have benefited from using the Split-Desktop@ software will provide insight to a wide range of software uses and potential applications like creating a database of geologic zone specific post-blast fragmentation information, underground draw point monitoring, stockpile, leach pile, and waste dump size measurement and monitoring, as well as many other applications.

Jan 1, 2000

By B. Lueger, D. Shen, M. Sedighy, R. Rand, R. Saleh, J. Cheung, M. Rifai, I. Khan, W. Sauri, D. Setianto

The world’s first active power demand stabilization system for a 3-electrode electric arc smelting furnace was commissioned at PT Vale Indonesia in December 2012 on Furnace No. 2 using an SPLC (Smart Predictive Line Controller). The SPLC technology in combination with the Furnace No. 2 rebuild and other upgrades has enabled PT Vale to increase the electrical input to the furnace by up to 20% on a stable and sustainable basis by eliminating peak powers that overload and trip out the electrical equipment, and by reducing power unbalances. The SPLC technology maintains smooth arc power using a continuously variable thyristor controlled series reactor. The SPLC compensates variations in the furnace arc with predictive changes in the circuit reactance at a speed of up to 60 times a second. The system started up quickly and has been shown to be easy to operate and maintain by PT Vale. PT Vale’s Operations Team has been testing the new system at set points of up to 90 MW on the newly re-built Furnace No. 2. Over the last 12 months, the throughput of Line 2 has increased by approximately 10% on an annual average; however, debottlenecking in other design areas of the operation is required in order to achieve 90MW operation on a sustainable basis. This outstanding success results from a combination of the furnace and other upgrades, the SPLC active power stabilization, and the skill of PT Vale in quickly adopting new technologies and maximizing the combined benefits of each technology in their operation.

Jan 1, 2014

By Amir Zavichi

Today, with the necessity of timely, on-budget and high quality completion of projects, proper use of construction equipment is essential to ensure project success. Construction equipment places a large monetary burden on the project and if not utilized efficiently, it can result in economic losses. Cranes are one of the most important and expensive operational devices on construction sites. They play a central role, and often activities that rely on crane services fall on the project?s critical path. Currently, material-handling scheduling is done by the crane operator or by an on-duty superintendent using his/hers personal judgment, making the process manual and timeconsuming. Thus, developing an optimal schedule, which considers different dynamic constraints in construction job site, may not be possible based on the current practice. This leads to longer operation times and a negative impact on project cost. This paper presents the latest results of an ongoing study, which aims to design and implement a nearreal time crane operation decision support system to be utilized directly by the crane operator or as an aid for the superintendent in scheduling optimal operation services. This system has several advantages such as maximizing the efficiency of crane operations, guaranteeing the best operation possible to reduce the crane?s travel time, reducing crews and equipment idle time, and minimizing the dependence on subjective human judgments.

Aug 1, 2013

By P González, J Videla, E Córdova, I Gottreux

Currently, underground mining of deeper massive deposits with lower grades, harder rock conditions in high strength environments, entails difficulties in caving, fragmentation and seismicity of the orebody.So far, the use of preconditioning (PC) with hydraulic fracturing (HF) has shown positive results in terms of seismic response and caving performance, while PC combined with explosives aims to weaken the rock mass, causing an additional effect on fragmentation.In particular, mines commonly referred to as ‘supercaves’, operated by caving methods, have the need to integrate mine to plant processes, where rock fragmentation appears as a key tool. In fact, it implies making mining and comminution processes more efficient to the plant and for mines, it justifies the search of innovative solutions in drilling and blasting techniques to precondition the rock mass. The following paper aims to show the feasibility of numerical blast modelling to weaken the rock mass using explosives, mainly through sensitivity analysis applied to designs to minimise bias and uncertainty in the results. It is shown how the presence of structures, their geometry and in situ stresses influence or interfere with the PC method being used.From the work, it is concluded that better knowledge on the application of explosives weakening allows specialists to strengthen numerical models associated with every design and therefore previously validate their applicability, helping to understand complex phenomena such as the propagation of mechanical waves in non-elastic heterogeneous media. In this sense, it is understood that while there are studies (Sanchidrián, Segarra and López, 2006) showing that the transfer of energy in the rock mass could be even greater in a confined environment, the more competent rock mass and higher in situ stresses interfere mostly on the effectiveness of a technique using explosives.CITATION:Gottreux, I, Córdova, E, González, P and Videla, J, 2016. Preconditioning modelling and explosives effectiveness in block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 683–688 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Earl C. Herkenhoff

Editor's note: The subject of mining on the moon can generate a wide range of strongly held opinion, from those leaning toward the view that, ultimately, such activity is the destiny of mankind to those who believe that all suggestions for moon mining to date are unrealistic, wildly expensive and in the hands of people who 'know nothing.' MINING ENGINEERING herewith publishes some of the basic pros and cons on the subject of moon mining by writers who are among those holding strong views on the subject, with the hope that some of our readers may be interested in joining this debate. Every mineralogist and most mineral industry people were keenly interested in the examinations of the first moon rocks brought back by US astronauts in 1969. Suffice to say that the examinations revealed nothing exotic in the mineral makeup of the very limited rock samples. The rocks were generally of igneous type, dark-colored and contained some common, Earth-type minerals. There was, in Earth terms, above average TiO2 content, but they contained nothing of commercial significance by Earth standards. Therefore, interest in moon minerals rapidly faded. Years later, on Sunday, May 4, 1986, living in Reno, NV, this author was shocked to read a local newspaper article by the Dean of the Mackay School of Mines, University of Nevada, Reno, headlined, "Moon Mining Not Far Off." Considering that the announcement more or less coincided with a slump in our domestic mining industry, the immediate questions in a reader's mind

Jan 1, 1991

By Kobayashi M, Kametani H

Particles of nickel flash furnace malle (45 per cent i) were oxidized in a dropping-particle furnace. The particles melted and the molten drops simulated those produced by the atomization of molten matte. The partly oxidized droplets were quenched and then reacted with silica flux to form high-grade matte (70 per cent i) and a fayalite slag. This paper describes the experimental equipment and deals with chemical aspects of the investigation such as volatile impurity distribution and thermodynamic considerations. The overall behaviour of minor elements such as Cu, Co, As and Pb was similar to that observed in conventional converting.

Jan 1, 1986

By Wittenberg J. C, Reid A. F

A method is described for the rapid and effective production of polished section mounts of ore and mineral particulates to the standards required for automated image analysis. This requires mounting without segregation of particles by mass or density, and it is also preferable to avoid having particles in contact so that they can be recognised as individuals. To achieve this, the particle samples are first split to an appropriate degree in a rotary riffle, and the sub-sample mechanically diluted and thoroughly mixed with an inert filler of the same size range as the particles. Just sufficient epoxy resin is added to make the mixture fluid. During setting, the ore particles are mechanically supported by the inert filler particles, thus maintaining the particles in a random three-dimensional distribution. A rapid two-stage grinding process, based on the successive use of 600 mesh silicon carbide and 1200 mesh (10 um) corundum on cast iron plates, is followed by three stages of mechanical diamond polishing on cloth laps. Hand polishing is entirely avoided, as is the use of papers.

Jan 1, 1984

By A. J. Monhemius

"The paper reviews the history of modern iron control processes in hydrometallurgy. Particular attention is paid to the processes developed in the 1960s by the electrolytic zinc industry for the removal of iron from zinc sulphate leach liquors - namely the Jarosite, Goethite and Hematite processes. Problems faced by the industry in the safe disposal of the iron residues produced by these processes are discussed. The lessons learnt over the past half century by the zinc industry are projected on to the current efforts to develop hydrometallurgical processes for the treatment of copper sulphide concentrates. It is argued that any attempt to create a “hydrometallurgical copper smelter” is doomed to ultimate failure, unless and until methods are developed that can recover iron from solution in a form that can be directly utilised by the steel or pigment industries.INTRODUCTIONYou suddenly realise that age is catching up with you and that technology is moving on apace when you are asked to talk about the history of a process or a technology that you’ve grown up with. Such was my reaction when, out of the blue, I received an email last year from the chairman of the CIM’s Historical Metallurgy Committee, asking me if I would give a talk on the early developments of iron control in hydrometallurgy. Once I’d got over the initial shock of realising that I had now become living history, I was of course flattered that the invitation was to give a talk at the prestigious IMPC, a conference series that has been going for as long as I have been in the business. That this particular IMPC was to include the 4th Symposium on Iron Control in Hydrometallurgy, made the invitation even more appealing and appropriate, because I was the co-chairman of the First Symposium on Iron Control, together with my old friend, John Dutrizac (known by many as Dr Jarosite), which was held 30 years ago in Toronto.first became involved with iron at the very start of my career in hydrometallurgy – the research topic for my Masters degree thesis at UBC, back in the mid 1960s, was “Reductive leaching of Goethite with SO2”. My thesis supervisor was the late Professor Ian Warren, who himself was a protégé of Professor Frank Forward, one of the founding fathers of modern hydrometallurgy. Little did I realise at that time, now 50 years ago, that the problem of iron and how to deal with it in hydrometallurgical processes would be a theme that followed me throughout much of my 40-year career in academia."

Jan 1, 2016

The 1963 Lignite Symposium was held on the University of North Dakota campus, Grand Forks, N. Dak., April 30-May 1, 1963, under the cosponsorship of the University of North Dakota and the Bureau of Mines. This symposium, the third in a series, had as a general objective the dissemination of information concerning advances in technology and utilization of solid fuels, with emphasis on lignitic coals. Approximately 150 representatives of industry, government, and educational institutions from 21 states and 3 Canadian provinces were present at the symposium. Those attending were welcomed by Marling J. Ankeny, Director of the Bureau of Mines, representing the Bureau, and Dean T. H. Clifford, Vice President of the University, representing the University.

Jan 1, 1964

The 1963 Lignite Symposium was held on the University of North Dakota campus, Grand Forks, N. Dak., April 30-May 1, 1963, under the cosponsorship of the University of North Dakota and the Bureau of Mines. This symposium, the third in a series, had as a general objective the dissemination of information concerning advances in technology and utilization of solid fuels, with emphasis on lignitic coals. Approximately 150 representatives of industry, government, and educational institutions from 21 states and 3 Canadian provinces were present at the symposium. Those attending were welcomed by Marling J. Ankeny, Director of the Bureau of Mines, representing the Bureau, and Dean T. H. Clifford, Vice President of the University, representing the University.

Jan 1, 1964

By Michael Young, Josh Rubenstein, Michael Cooper, Tom Shouldice, Dan Curry

"Xstrata Nickel Australasia’s Cosmos plant in Western Australia is currently implementing a debottlenecking project to increase nickel output while maintaining metallurgical performance and a low unit cost for production. Mineralogical analyses indicated that the processing bottlenecks could be removed by simply reconfiguring portions of the circuit as well as adding capacity with technical advancements – notably an IsaMill™, Jameson Cell, Wemco® SmartCell™ and Larox Filter.The Wemco® SmartCell™, which is particularly suited for coarse mineral flotation, and Jameson Cell, which is particularly well suited for fast floating and fine minerals, combine as rougher scalpers to complete the main stream portion of the flotation circuit. Addition of the two new cells meet the required flotation capacity to handle the forecast increase in nickel feed grade and tonnage.The addition of an IsaMill™ for regrinding allows the SAG mill to produce a coarser primary product, thus enabling increased throughput. The advantages offered by the IsaMill™ include operation in open circuit (internal classification), an inert grinding environment (ceramic media) for better downstream flotation (“clean” new surfaces), compact footprint (easy to retrofit into existing plant) and energy efficiency. With the new rougher capacity addition, the remaining original plant cells were reconfigured to suit the new regrind mill and cleaning requirements. The existing 24 m2 Larox pressure filter was replaced with a larger 32 m2 unit to dewater the increased concentrate output.The paper describes the upgrade at the Cosmos concentrator with particular emphasis on the mineralogical data and metallurgical benefits associated with the changes.INTRODUCTIONThe Cosmos concentrator is located 680 km northeast of Perth in Western Australia. The deposit’s development and operations were started in 1999 by Jubilee Mines NL, Cosmos’ previous owner, with the first production of nickel concentrate in April 2000. The Cosmos concentrator treats a komatiite hosted high grade nickel sulphide ore, with sulphides being predominantly pentlandite and pyrrhotite with lesser amounts of pyrite and chalcopyrite."

Jan 1, 2010

By Chris Larsen, Ian Orford, Mike Cooper

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod and primary ball mills. The 8.54m diameter x 4.27m long (EGL) AN1 mill is driven by a bidirectional variable speed 6.3MW ABB wound rotor motor with Slip Energy Recovery (SER) drive. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill is operated in closed circuit with horizontally inclined 660mm diameter cyclones to produce a circuit product P80 of 85 microns. Extensive test work and JKSimMet design modeling resulted in a production circuit operating closely within design expectations.The circuit is highly instrumented and controlled via a hybrid Programmable Logic Controller (PLC-5) and Fisher PROVOX Distributed Control System (DCS) that is in communication with the property information highway. An expert control system (Gensym G2) is used for control of the SAG mill load.Engineering and construction were completed in 28 months from the time of management approval for the project. The Brunswick AG/SAG mill circuit was commissioned on schedule at the $M 23.5 forecast budget."

Jan 1, 2001

By Romano J. Micciche

One of the largest scale uses of a multiple, high-strength steel bar tiedown system is described. Tiedowns were installed to resist hydrostatic uplift forces acting on a section of the Interstate Highway Route I-90 southern approach roadway to the Third Harbor Tunnel, in Boston, Massachusetts. Site specific information is discussed regarding design, testing, and installation of Tiedowns. Conclusions are presented regarding the overall performance of this system and the application of this type of tiedown system on future projects.

Jan 1, 1994

By Rob Domotor

This paper tells the story of using controlled surface and underground blasting methods to excavate hard rock in three areas on Australia’s largest road infrastructure project; the Airportlink Project in Brisbane; worth a total value of AUD $4.8 billion. The project used blasting methods including design, modelling, drilling and loading of the explosives that had never been used before in Australia, some of these were probably unique in the world.

Jan 1, 2012