Search Documents

By J. Keith Haddock

"Introduction The Luscar company, Forestburg Collieries Ltd., operates the Diplomat Mine located 14 km south of Forestburg, Alberta. Production is now at a declining rate from the 1 million tonnes achieved in 1978 as the reserves are being depleted. Three pits are operated at this prairie strip mine utilizing draglines and stripping shovels to uncover the coal. The coal is hauled to a tipple on site for shipment by rail or highway vehicles or is hauled directly to the adjacent Battle River Generating Station. Geology The mine is currently extracting the Battle River seam on the north side of the Battle River. This is the lower-most seam in the Horseshoe Canyon Formation and is the only one present in the area, the upper seams having been eroded by glaciation. The seam lies generally flat and varies from 2.0 to 5.0 metres thick. It lies under glacial till overburden varying in depth from 5.0 to 12.0 metres. The mineable coal extends from the side of the Battle River valley where it outcrops, to approximately 2.5 kilometres to the north. The mine is spread out over a distance of 8.0 kilometres in an east-west direction. Reserves and Coal Quality After over 30 years of mining at Diplomat, there are now less than 1 million tonnes of mineable reserves remaining on the property. With the commencement of coal production from the Paintearth Mine in 1981, supply to the Battle River Generating Station, formerly Diplomat's biggest customer, is being transferred to Paintearth. Rail shipments and domestic supply will continue until reserves are depleted. The coal has the following specifications:"

Jan 1, 1985

By J. C. Johnson

Underhand mining with cemented mill tailings for backfill has proven to be a safe and effective alternative to conventional overhand mining for rockburst prone mines. The ability of the cemented sandfill to survive a rockburst shock wave without failing has been observed at mines in the Coeur d?Alene Mining District many times in the last twenty years. To better understand the dynamic loading of this commonly used support material the National Institute for Occupational Safety and Health (NIOSH) performed laboratory experiments using a split Hopkinson Pressure Bar (SHPB) to quantify the maximum stress and energy absorption of cemented mill tailings from the Galena mine. Cylindrically shaped cemented backfill specimens aged 28 days were placed in the split Hopkinson pressure bar testing apparatus and a dynamic load was applied. The measured peak dynamic compressive strength of the cemented sandfill was 10.6 MPa (1540 psi) and is approximately twice the static unconfined compressive strength (UCS) of 5.5 MPa (800 psi). These test data showed about 95% of the initial energy was reflected away from the backfill and only 5% of the energy was absorbed. This may help to explain why backfilled stopes could withstand seismic events up to 3.5 Richter magnitude (Ml). When a compressive rockburst wave impacts a stope a large amount of the stress and energy is reflected away. The reflected wave is a tensile wave which creates tensile cracks and spalling in the entire wall of the stope. The backfill supports the damaged wall rock and holds it in place. Some of the stress and energy of the rockburst is transmitted into the backfill and because the backfill is being dynamically loaded it has a strength that is twice its static value and absorbs a substantial amount of rockburst energy. Although mining in deep underground mines is an extremely hazardous occupation, the use of underhand mining with cemented backfill for static and dynamic ground control increases the safety of the workers.

May 1, 2007

By Jai-Woon Moon, Wonnyon Kim

Deep-sea hydrothermal vents (hereafter chimneys) are commonly found on the new crust forming along divergent plate boundaries. Related to the chimney cycle from birth to death, it is hard to define the growth stage of the chimney due to a brief life span of the venting hydrothermal plume. Here we try to categorize the mineral magnetic properties of the chimneys according to their venting fluid-temperatures. Hydrothermal sulfide deposits in the Southwest Pacific were explored in 2012 and chimneys were collected using remotely operated vehicle (ROV) and Grab with AV camera (GTV). In the present study, mineral magnetic properties of three Cu-rich chimneys were measured: a high-temperature chimney showing a venting fluid-temperature of about 200°C (ROV01); a lowtemperature chimney of about 80°C (GTV01); and an inactive chimney (ROV02). The chimneys were sliced to ~1 cm intervals from core to outer margin. Magnetic properties of ROV01 are dominated by pyrrhotite, except for the most outer part that experienced severe oxidation. Concentration and grain-size of pyrrhotite are relatively low and fine respectively. In the GTV01, pyrrhotite, dominant in the core, is gradually mixed with hematite toward the outer margin of the chimney due to secondary oxidation. Both the concentration and grain-size of the magnetic minerals are greater compared to the GTV01. High concentration and large grain-size of magnetic minerals characterize ROV02. Dominant magnetic phases are pyrrhotite, hematite, and goethite. In particular, the most outer margin shows the presence of magnetite produced possibly by magnetotactic bacterial activity. Such distinctive contrast in magnetic concentration, grain-size, and mineralogy among three different types of chimneys enables the life stage of the Cu-rich chimneys to be determined through a mineral magnetic study.

Sep 1, 2014

By Norman O. Lotter, Simon Yu, Tony Deng, Antonio Di Feo

"Xstrata Nickel’s Raglan operation, northern Québec, achieved paymetal recovery gains in 2007 by switching the collector from potassium amyl xanthate to sodium isobutyl xanthate. To follow on from that position, Xstrata Process Support (XPS) and A. Di Feo of Raglan proposed that a mixed xanthate system be formulated and tested towards further performance gains. This work selected ethyl and isobutyl xanthates as the candidates. An optimized ratio of these was to be determined by a designed experiment. This suggestion was based on an abundance of published literature that reported mixed collector systems outperformed single ones. A partial factorial design was used to configure four test conditions and a mid-square for the flotation work. The testwork was conducted using High Confidence Flotation Testing. The raw data were analyzed and modelled by Design-Expert software. An optimum ratio of 1.6:1.0 by mass (1.32:1.0 in molar terms) of isobutyl:ethyl xanthate was determined. Without this modelling, the optimum ratio would have been missed. Results obtained with the new baseline flotation test using this optimized mixture showed a 3.3% Ni recovery gain in the bypass concentrate and more than 1% recovery gain for PGM over the single PIBX system. This system has been proposed for and accepted as a plant scale trial in the first half of 2010.INTRODUCTIONConcentrator OperationsMilling and flotation of sulphide ores ahead of smelting and refining is a common practice. This choice results in the larger and more variable paymetal loss in the production of saleable metal [Cramer, 2001]. For this reason, it is common to see an ongoing performance improvement programme at the operations level. When successfully performed, these e"

Jan 1, 2010

By Joe Zhou

"Mineralogical characterization and metallurgical extraction of silver is challenging due to its complex mineralogy and chemistry. Over 200 Ag-bearing minerals have been identified and a silver-rich ore body would typically contain 5 to 10 different silver minerals. Silver can occur not only as discrete microscopic (visible) silver minerals but also as submicroscopic (invisible) silver in other minerals. During processing, silver may form passivation compounds such as silver hydroxide, silver sulphide, jarosite-like silver sulphate, silver halide or silver cyanide precipitate, all of which may negatively impact on silver extraction. Knowing the deportment of silver in the ore and its metallurgical products is important in flowsheet design and plant optimization. This paper begins with the classification of silver ores and minerals and a review of processing techniques, and focuses on the major mineralogical factors to explain why and how these factors affect silver extraction. Case studies are provided to demonstrate the application of silver process mineralogy in flowsheet design and plant optimization.INTRODUCTIONSilver was known to and utilized by mankind since ancient time. Actually, it was one of the earliest metals discovered and utilized by mankind after gold and copper.Silver is the whitest metallic element. It is rare, strong, corrosion resistant, and unaffected by moisture, vegetable acids, or alkalis. Silver is also resonant, moldable, malleable, and possesses the highest thermal and electric conductivity of any substance. The chemical symbol for silver is Ag, from the Latin argentum, which means white and shining. Although silver does not react with many chemicals, it does react with sulfur, which is always present in air at trace amounts. The reaction causes silver to tarnish, and consequently it must be polished periodically to retain its luster.Silver possesses many special physical characteristics and qualities that make it useful to a variety of industries. The photography industry is the biggest user of silver compounds. Silver forms the most light-sensitive halide salts, which are essential to developing highquality photographic prints. Silver also has the highest electrical conductivity per unit volume of any metal, including copper, so it is used extensively in electronics."

Jan 1, 2010

By C. Musingwini, G. Njowa, M. Burnett, C. C. Birch

From 2022 to 2040, the global demand for mineral commodities is projected to increase by fourfold to six-fold, largely due to traditional drivers such as population growth and urbanisation compounded by the adoption of decarbonisation technologies that are more mineral intensive than fossil fuel technologies. To meet this projected demand, companies operating in the minerals industry should accelerate the development of mineral projects. Since most of the companies generally operate in multiple geographical, regulatory or legislative jurisdictions, it is critical that the information on Mineral Resources and Mineral Reserves they report on in the public domain should be comparable and consistent across different jurisdictions. The Committee for Mineral Reserves International Reporting Standards fosters alignment of national and regional mineral reporting codes through an internationally accepted template that creates common technical understanding of definitions, classification, estimation processes and the Public Reporting of Exploration Results, Mineral Resources, and Mineral Reserves. The Committee for Mineral Reserves International Reporting Standards Template-based codes guide reporting at respective national and regional levels. Since mine planning is critical in the conversion of mineral resources to mineral reserves, a shared technical understanding should aid comparability of mine planning results. However, differences persist in the way mine planning results are reported. Unlike most previous studies, which have primarily focused on comparing mineral reporting codes, this paper updates and extends such comparisons by exploring how similarities or differences in reporting should influence the mine planning process. It also recommends some principle and process changes to assist mine planning professionals to improve consistency and comparability in reporting mine planning results.

Mar 30, 2026

By H. L. Gilbert

Improvements in production of high-purity chromium metal by magnesium reduction of anhydrous chlorides and by hydrogen treatment of electrolytic chromium are reported. Hydrogen-treated chromium has been arc-melted, and the arc-melted material has been successfully forged, rolled, and swaged. The material also has been forged at liquid-air temperatures. X-ray and metallographic studies indicate the recrystallization temperature of rolled chromium sheet to be about 750° C. Preliminary investigation of hot-bending characteristics of rolled chromium sheet shows the minimum bending temperature to be about 325° C. The heat resistance of chromium has been investigated.

Jan 1, 1952

By Dushasan Kundu, B. N. Shivakiran Bhaktha, Khanindra Pathak, Sarbojit Mukherjee

Mine safety and quality of life of miner working in underground mines depend to a large extent on mine illumination and communication. The provisioning of reliable, safe, and cost-effective illumination is critical, particularly in underground gassy coal mines. To prevent firedamp explosion by electrical switching operation in coal mining industry requires implementing intrinsically safe illumination circuit. The luminaire design also needs to be certified and installed properly. The current illumination systems installed inside mines require a lot of energy which is obtained from nonrenewable resources. In this work, the design and implementation of solar-powered optical fiber-based illumination are studied and implemented in the Jhanjra underground coal mine, Eastern Coalfield Limited, and a Li-Fi-based communication system for underground coal mines is proposed. Silicate optical fibers of various core diameters and numerical apertures are characterized for illumination applications and their efficiencies are reported. The possibility of achieving optical fiber-based solar, laser, and hybrid illuminations in underground mines is discussed. The design and fabrication of a Fresnel lens-based solar tracker for solar illumination are also presented. The optical fiber-based illumination system is installed in an underground coal mine and the illumination of over 70 lux is achieved at the work plane. Finally, optical fiber-based illumination and simultaneous basic Li-Fi communication are demonstrated and will be beneficial to the underground coal mining industry.

Apr 14, 2023

By R. C. FLEMING

MINING rock asphalt for use as a paving material is an industry which has grown with the spread of the good roads movement. "Mineral Industry During 1930" reports asphaltic pavements constructed, including maintenance and repair but excluding pavement constructed with road-oil, cut-back or emulsified asphalt, as grown from 23 million square yards in 1911 to a high of 144 million in 1927. In 1930 the same source reports 106 million square yards of such paving laid and, in that year, 664,871 tons of native rock asphalt were so utilized. Many states contain rock asphalt deposits of greater or less importance but in only a few places are the de¬posits being mined commercially. In the year cited Ken¬tucky produced 305,024 tons of bituminous sandstone, Texas 270,138 tons, mostly bituminous limestone, while Alabama, Oklahoma, California and Utah produced 89,709 tons of bituminous rock for road construction. In addition Utah produced 37,906 tons of the purer asphaltic products, gilsonite, wurtzilite and ozokerite, for other uses. Speaking generally, the rock asphalt is a sandstone or limestone naturally impregnated with asphalt to an extent that makes it an ideal road surfacing material without mixing or treatment other than crushing. The asphalt content of the commercial product runs 8 to 12 per cent.

Jan 1, 1933

By R. W. Carn, D. Vincent

Environmental Considerations With significant increases in bulk coal movements through terminals, operators are under constant social and political pressure to reduce or remove environmental pollution problems incidental to their operations. To meet these requirements, both equipment manufacturers and terminal designers are endeavoring to design equipment and systems with stringent environmental controls. The most challenging environmental problems facing coal terminal designers and developers are terminal siting restrictions, dust control, and noise abatement. Terminal Siting Finding a suitable site can be a difficult problem because of public concern over coal dust or the impact of a terminal on the surrounding community or natural habitat of the area. Often the only suitable flat land available for terminal development is on a tidal estuary or salt water marsh with great environmental value. In many cases a period of four to six years of full environmental and social assessment has been needed. A recent example of such difficulties is the expansion at Roberts Bank, British Columbia, where environmental impact assessment studies and their public review took almost six years from initial expansion applications until the time of approval. Dust Control Modern coal terminal dust control techniques usually consist of water sprays at strategic locations to suppress dust. The application points include rail car or barge dumper, main conveyor transfers, perimeter sprays around stockpiles, stacker/reclaimer, ship-loader transfers, and loading spout. The water sprays may include a chemical wetting agent or surfactant to reduce the water requirement and increase effectiveness. Recently there have been advances with development of effective micro foam agglomerating agents. In these systems, a micro foam with very small bubble sizes is sprayed into the coal stream. The foam fills the interstices between coal particles and wets the coal fines. These systems have proven to be very effective and usually one application before stockpiling and one upon reclaiming will markedly reduce the coal dusting. Stockpile perimeter sprays can be operated either manually or at the sophisticated terminal, actuated by a computerized control system that senses key environmental conditions such as humidity, precipitation, and wind velocity. Most modern terminals collect the drainage from the stockpile area, remove the solids in settling basins, then recirculate the water to reduce water requirements and effluents from the site. Dusting of long-term storage stockpiles can be reduced by spraying the piles with chemical resin or latex binding compounds to seal the surface. These compounds also can minimize erosion of the pile by rainfall. Dust collection with air evacuation systems and cyclone or wet scrubbers can be used at key areas such as rail car dumpers, main conveyor transfers, and ship-loader spouts. The trend in dust control is away from dust collection since most dust collectors are high maintenance items requiring good operator supervision and servicing. Coal handling conveyors are usually open and uncovered. However, in areas requiring special attention they may be covered or even completely enclosed. Dust generation from terminal roads is often a significant amount of the total dust emitted from a terminal. To reduce this dusting, roadways where traffic is heavy can be paved or sprayed by water trucks. Speed limits can be enforced and use of tracked mobile equipment for stockpile handling rather than rubber-tired loaders is encouraged by authorities. Noise Abatement Terminals located close to residential areas are often faced with noise control problems. Noise can be one of the most difficult environmental problems to solve. Usually, use of electrically-powered equipment is encouraged to reduce noise levels. Rail car dumper houses can be totally enclosed to reduce both dust and noise emissions. Diesel locomotives can be fitted with special muffling devices. Green belts of trees surrounding a terminal or the ap-

Jan 7, 1983

"In mining operations, it is widely accepted that strategies to drive operational goals must revolve around improving plant availability, reliability and process efficiency. In this paper, an integrated solution framework for reducing process variability, increasing process efficiencies and maximizing plant availability and reliability is discussed within the context of a typical milling circuit. The framework exploits a real-time analysis “gap” evident in production operations that prevents timeous identification of equipment and process failures. This is achieved by leveraging predictive analytics for equipment health monitoring, control loop monitoring and advanced regulatory control solutions towards enhanced process performance, improved asset management and regulatory compliance. The framework provides for early and actionable warnings on equipment and process degradation using real-time operational data.INTRODUCTION The changing landscape of gold mining and processing presents many challenges that threaten sustainability of existing (marginal) operations as well as deter investment in new projects. As existing “shallow” ore resources become depleted, mining operations are increasingly treating low-grade ores with complex and randomly variable mineralogical characteristics. For example, in South Africa, historically one of the major gold producers, the average grade of ore treated has been decreasing from averages above 4.5 – 5 g/t to current grades averaging less than 3 g/t within a decade (Chamber of Mines, 2012). Moreover, lower tonnages are being treated as a result of the narrowing of the available resource base. Also, the regulatory framework has tightened over the years due to heightened concerns on the safety, health and environmental impacts of mining and related activities."

Jan 1, 2014

By Oliver Bowles

Under a cooperative agreement between the Bureau of Mines, the United States Geological Survey, and the United States Bureau of Standards, a study of the stone-quarrying industries of the country was begun in 1914. The results of investigations made have been published from time to time.1 During the World War the Bureau of Mines centered its attention on problems relating to national defense, and detailed studies of stone-quarry problems were not undertaken except for an investigation of labor saving at limestone quarries, reported in Technical Paper 203, which related to a question of military importance. Since the return of peace, the high cost of materials and labor has made more imperative than in prewar times the conduct of investigations for aiding the quarrying industries in every way possible to adopt more economical methods and to utilize the most efficient labor-saving equipment. The publications already issued have had a wide demand, and in the interest of the quarry industries the bureau proposes to issue additions to the series as rapidly as funds are available. In an endeavor to promote economy and the reduction of waste in the slate industry, a study of slate quarrying was begun in 1920 and covered a period of about two years. Sixty-five active quarries were visited, and a detailed study made of all problems bearing on their successful operation. Field study was supplemented by a study of all information available in books or published articles on slate quarrying.

Jan 1, 1922

To improve communication among Government, industry, and academic researchers in the field of thermodynamics, the Federal Bureau of Mines sponsored a Workshop on Techniques for Measurement of Thermodynamic Properties in August 1979. Participants at the workshop presented 33 papers on the subjects of temperature measurement and control, general calorimetric techniques, low-temperature calorimetry, high-temperature calorimetry, galvanic cells, ionic solutions, and heterogeneous phase equilibria. A special invited lecture was presented by E. F. Westrum, Jr., on the resolution of lattice heat capacity. This Information Circular comprises the proceedings of the workshop and includes the texts of papers presented and discussion by attendees.

Jan 1, 1981

Senior staff representatives of the Bureau of Mines and the National Institute for Occupational Safety and Health (NIOSH) met in Washington on September 6, 1972, to review and evaluate their cooperative accomplishments to date and to consider the planning and conduct of future coordinated activities. The six presentations given at this joint staff seminar are published here for the benefit of those concerned with the problems of coal mine health, and especially those with responsibilities in administering the Coal Mine Health and Safety Act of 1969.

Jan 1, 1972

By AIME AIME

THE Iron and Steel and Institute of Metals Divisions will meet jointly at the Statler Hotel, Detroit, Oct. 4 and 5, during the Metal Congress, Oct. 2-6. The Wire Association, the American Welding Society and the American Society for Steel Treating, together with the two Divisions of the Institute, constitute the Congress this year, and each body offers an interesting technical program. The National Metal Exposition will, as usual, be held concurrently. Visiting metallurgists will find themselves engaged in a bit of research not listed in the program-a time study of how best to exploit in a few days both the Congress and all that the place of meeting has to offer. For Detroit, the beautiful "City of the Straits," is third in rank industrially in the United States, and its great manufacturing plants offer much of metallurgical interest. This is especially true of the automobile plants which will be open to members of the various societies during the week of the Congress.

Jan 1, 1933

By Adams F. C, Ridley K. L

Economic conditions after WorId War II made the recovery of Australian sources of sulphur one of considerable national importance. From 1947 to 1949 an investigation was made of recirculation techniques to produce acid plant grade gas from the Dwight-Lloyd down-draught sintering plant.During 1949 it appeared feasible to produce a gas of suitable 802 concentration and a decision was made to construct a gas purification train and a 150 tons/day contact acid plant. However, a number of difficulties remained in the production of the gases for sulphuric acid manufacture and as a result of research conducted to overcome these troubles the continuous up-draught sintering process was developed.The principal difficulties were:(a:) The down-draught sintering practice, as developed, produced an unusually high metallic lead precipitation in the windboxes. The disposal of this lead interrupted sintering operations and the delivery of gas to the acid plant.(b) The production capacity of the existing sintering plant was fully extended and the adoption of recirculation of gases, in an endeavour to satisfy acid plant requirements, would probably reduce the plant production capacity.(c) The prevailing high temperature of water available for purification train cooling required a higher than...

Jan 1, 1956

By L. A. Neumeier

The Bureau of Mines investigated hot-rolling and forging characteristics of experimental ductile iron castings, both sand and permanent-mold, made with charges containing up to 70 pct foundry pig iron and 95 pct steelmaking pig iron. Between 1,550° and 1,950° F, most castings could be rolled to 90-pct reduction or forged to 70-pct reduction without serious cracking. Charge and composition have less bearing on workability than on subsequent properties. Permanent mold castings could be worked as readily as sand castings at 1,750° and 1,950° F. Plasticity improved with temperature. Small billets were also forged cold to 50-pct reduction without cracking. With equivalent nodularity, composition affects properties of wrought materials by altering matrix structure and strength. Properties vary with reduction and improve with increasing working temperature. Rolled material has high strength and anisotropy, and low ductility, particularly in the trans-verse direction. Annealing reduces strength and improves ductility, but anisotropy persists. At 70-pct reduction, impact resistance in the longitudinal direction is about twice that in the transverse. Annealing roughly doubles impact resistance. Deformation enhances damping capacity. The feasibility of die-forging and bar-rolling of ductile iron was evaluated in trial tests conducted under a Bureau contract. Although workability and ductility of ductile iron are inferior to those of steel, more advantage could be taken of ductile iron's plasticity to work rough shapes to final dimensions.

Jan 1, 1980

By Frederick A. Mumpton

Recent findings by medical workers on the association of certain zeolite minerals with the high incidence of pleural mesothelioma in two small Turkish villages have caused considerable excitement both in medical circles and in the synthetic and natural zeolite businesses. The 42 cases diagnosed between 1970 and 1977 in one community of 600 population in a region of altered volcanic tuff represent a virtual epidemic of this rare malignancy which normally strikes only about one person in a million. Cancer workers around the world expect that detailed environmental and epidemiological studies of the disease in these areas will shed considerable light on the cause of this particularly lethal form of lung cancer. Scientists and engineers developing uses for zeolite materials in industry and agriculture, however, are justly concerned that the preliminary results available on this situation will be used by environmental and regulatory organizations to label an entire group of miner- als as carcinogens on the basis of what is little more than circumstantial evidence. Although there is no question as to the large number of cases of mesothelioma in these areas of central Anatolia, the work to date has suffered from a lack of sound geological and mineralogical input. Ataman (1) stated that a "correlation" exists between mesothelioma and zeolites in this region; however, the geological data needed to document a direct relationship between the presence of zeolites in the volcanic tuffs surrounding the villages in question and the rate of malignant lung disease in the inhabitants have g been obtained, nor has evidence that suggests a cause-effect relationship between zeolites and cancer been reported. To provide fundamental information on the distribution of zeolite minerals in areas of central Turkey where high incidences of pleural mesothelioma have been reported and to evaluate from first-hand knowledge the published reports and news releases of medical workers engaged in assessing the problem, the following investigation was made.

Jan 1, 1979

By F. E. Heuze

This article deals with the effects of high-explosive and nuclear explosions in rock masses. We first highlight the strong influence of geological discontinuities, such as joints and faults, on ground motion characteristics. Then, we briefly introduce the Discrete Element Method, as a new technique for numerical simulations. II is shown to be far superior to continuum-based approaches, when dealing with the dynamics of discontinuous media such as jointed rocks. Finally, we simulate the ground effects from a generic contained nuclear explosion, which bears some similarity to the SHOAL event in granite. This calculation is intended to emphasize the influence of the near-source geology on the distribution of energy, and on the motion at various azimuths in the medium.

Jan 1, 1991

By H. Powell

"This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, on-line technologies through review of published information available for on-conveyor minerals applications. Case studies include an iron ore and copper-gold company, both of which consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.INTRODUCTION Process operators rely on supply of a reasonable ore quality and consistency from the mine. Unfortunately neither the mining nor process operators have much control over the ore quality once it has been put into the crusher. Grade control typically stops once the material is designated as ore and the process plant operator needs to process it irrespective of quality. Plant control is most effective when technologies measure process streams directly and preferably in real time. Measuring sampling streams that are not representative of the primary flow will result in incorrect plant control decisions. Sampling coarse conveyed flows is expensive and impractical at many operations, however, this does not mean those flows cannot be measured. Investigations to find techniques suitable for real time elemental analysis have focussed on the application of known laboratory techniques to process streams. For conveyed applications, development of neutron irradiation techniques were most promising and early studies indicated potential success for bauxite measurement (Beurton et al, 1995). Tran & Evans (2001) concluded there was no equivalent technology to PGNAA in terms of material penetration power and that the technology was eminently suitable for basic industries such as cement. Nelson and Riddle (2003) evaluated PGNAA for possible use in the phosphate industry by using a unit installed in a cement plant to test performance on phosphate samples and ultimately recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control"

Jan 1, 2014