Search Documents

By R. E. Ray

Compared to conventional fully ducted axial and centrifugal fan systems, jet fans can offer a number of advantages for control of smoke during fire emergencies and dilution of diesel engine exhaust products in vehicular and rail tunnels. The success of jet fan applications is the result of a balance between the temperature de-rating of the fan, buoyancy forces and the installation momentum transfer efficiency. This paper provides a case study of a unique application of vertically-mounted jet fans in ventilation shafts used to provide both emergency ventilation and pollution control for an overbuild created by the construction of a series of commercial high-rise residential buildings over a portion of an existing passenger rail line. A detailed evaluation of a set of shafts for one building is presented, including a discussion of the calculation methods used to estimate the required jet fan capacity and the results of the subsequent numerical analysis using Computational Fluid Dynamics to simulate the performance of the jet fans during train car fire emergencies.

Jan 1, 2009

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By Neil A. Brown

The trona deposits near Green River, in southwestern Wyoming are world class in size and quality. They contain more than 25 times the reserves of the next largest trona deposit at Lake Magadi in Kenya. Based on present rates of production, the Green River reserve should last for more than 500 years. Since their discovery in 1938, the Union Pacific Corp. has been instrumental in the promotion, development and production of soda ash in Wyoming. Union Pacific spent several years drilling the deposits and trying to promote them to chemical companies. In 1947, Westvaco and Union Pacific entered into what became the first trona lease agreement. Today, the Green River Basin leads the world in soda ash production, accounting for about 25% of the world's supply. Green River producers process more than 14.5 Mt/a (16 million stpy) of trona to produce more than 8 Mt/a (9 million stpy) of soda ash. The future for Green River soda ash looks good, with more of the world looking towards the cheaper and higher quality source of soda ash coming from the natural deposits. Production from the Green River deposits should continue to grow as trade barriers and tariffs begin to fall in Europe and energy and environmental costs force the synthetic producers to exit the market.

Jan 1, 1995

By S. Ngidi

Palabora Mining Company operates a low grade underground copper mine situated in the Limpopo Province, South Africa. Full production was first reached in May 2005 after a successful transition from an open pit operation to an underground block cave operation. The operation faces a number of technical and operational challenges, not the least being fragmentation of a competent rock mass and external dilution. The cave is subdivided into three main sectors being the east, the west and the central sectors. Caving was initiated from the weaker central sector, which has the majority of its drawpoints located directly under the open pit bottom currently filled with about 130 million tons of waste material from the pit wall failure incurred in 2004. About 48% of the ore reserve has to be extracted from the western sector, which has a much courser fragmentation compared to the other two sectors and only 25% from the central sector with the finest fragmentation. The main constraint during the ramp-up stage has been secondary breaking of drawpoint blockages. Ground-breaking secondary breaking and cave management initiatives and practices have made it possible for Palabora to realize and sustain high production rates.

Jan 1, 2007

By Rob Farnfield, Ben Williams, Ashley Haslett, Diane Cartledge

Major accidents that occur within our industry are often tragic and expensive, damaging reputation and threaten the livelihood of the business. There isn’t anything in them that can be seen as positive for those that experience them. They undertake what are usually very painful, detailed and time consuming investigations to discover how the incident occurred and what needs to be done in the future to prevent similar incidents occurring. Many admirably choose to share the lessons learnt through industry organizations such as SAFEX International so that we can all have the opportunity of preventing similar incidents from occurring within our own organizations.

Jan 1, 2016

Much interesting data on cemented carbides has been published over a period of years which, when classified and pieced together, gives a clear picture of this special branch of powder metallurgy. This is an attempt to present the essential information in an ordered account.THE HARD CARBIDES-THEIR PROPERTIES AND PREPARATIONThe so-called hard or refractory carbides are the carbides of a number of metals which are grouped together in the Periodic Classification. These metals are in groups IV, V and VI. They are titanium, vanadium, chromium, zirconium, niobium (columbium), molybdenum, hafnium, tantalum and tungsten. These carbides have attracted the attention of chemists because of their remarkable properties. They possess very high melting points, and are rather difficult to prepare in the pure state. Their outstanding propertyis their extreme hardness, which they share with certain other carbides, such as those of silicon and boron. In addition, these compounds possess distinctly metallic properties, such as lustre (in fused specimens) and high thermal conductivities.(l)t They are capable of forming alloys in two ways:1. With metals, particularly those of the iron group. 2. With each other (a case of solid solubility).The constitution of these substances is not that of ordinary salts, which obey the usual valency rules, but must be likened to that of certain intermetallic compounds. Actually they are "interstitial" compounds(2), that is, they are formed from the ordinary metallic lattice by the insertion of the relatively small carbon atoms in the interstices.. The energy required to fill the lattice completely is high, and this explains the difficulty often found in obtaining the exact stoicheiometric compound. Thus the carbides can have a range of composition, and can be considered as solutions of carbon in the respective metals.Physical Properties of the CarbidesThe hardness of these compounds is so great that it is difficult to compare the individual compounds on this basis. Becker(l) gives values on Moh's scale, which are not very accurate and are of no great value. Burden(3) has reproduced a diagram by Hatfield which indicates that the cemented carbides are between 1,400 and 2,000 on the Vickers diamond scale. However, the pure carbides are harder, tungsten carbide being about 2,200. Hoyt(4) describes a method of measuring hardness applicable to powdered specimenswhereby the powder is rubbed on a standard block of cemented tungsten carbide under standard conditions, and the rate of wear is determined. In...

Jan 1, 1942

By N. Kumar Kittusamy

The purpose of this study was to assess the adequacy of the cab design and to determine the percentage of musculoskeletal symptoms among operators of mobile equipment used in mining and construction. A questionnaire was designed to assess demographics, work information, job history, and musculoskeletal symptoms in operators of heavy mobile equipment. Information concerning equipment included design of the seat/chair, levers, pedals, bothersome vibration, quality of ingress/egress from the equipment, proper preventative maintenance and repairs, and age of the equipment. The body regions that were evaluated included the neck, middle/upper back, low-back, shoulder/upper-arm, elbow/forearm, wrist/hand, hip, knee, and ankle/foot. Five hundred and eighty six operators completed the questionnaire. The results indicate that these workers are at risk for developing musculoskeletal disorders, and the need to quantify risk factors (i.e., whole-body vibration and static sitting postures).

Jan 6, 2006

By Peter Swanson

One of the primary methods for analyzing roof stability in underground mines is the age-old method of “roof sounding” where a miner taps on the roof and listens for the hollow sound of loose blocks of rock. This paper looks at the feasibility of using noncontact laser-based vibration measurements to detect roof fall hazards with the ultimate vision of improving, expanding and automating procedures for mine roof inspection. Vibration measurements made on loose blocks of rock in underground mines are summarized and compared to estimates of fundamental resonance frequencies for rock slabs of the size responsible for highly hazardous “skin failures.” Both laser Doppler vibrometry and full-field interferometric methods are examined and are considered to be feasible methods for detecting anomalous vibrations in loose roof rocks. Results from simple laboratory experiments using laser vibrometry demonstrate some of the proposed application concepts. While considered a challenge to move these techniques from the laboratory to heavy industrial or outdoor environments, the potential for success in the current application is enhanced by the reduced requirements of qualitative analyses.

By Beevers J

The Ok Tedi Project is now a high production open-pit porphyry copper mine located in the Star Mountains of Papua New Guinea (PNG). At present, total daily production is 190 000t of ore and waste. Large scale drilling and blasting has only been in operation since 1988, prior to which all material was removed by ripping and dozing. This paper reviews the steps taken over the last 12 months in establishing a more efficient drilling and blasting operation and highlights the significant reduction in powder factor. These improvements have been achieved largely through the introduction of air-bags, controlled pattern expansion and an overall focusing on the operation by involving consultants, ICI's technical service and internal departments.

Jan 1, 1991

DESCRIPTION OF OREThe ore consists, in general, of a very finely grained mixture of sphalerite, galena, and pyrite, with a gangue of quartz and schistose material, and contains about one ounce of silver to the unit of lead.Minor minerals are chalcopyrite, tetrahedrite, and ruby silver. The amount of gangue within the ore-bodies themselves is usually less than 20% of the weight of the whole. The ore is banded in a way that corresponds to the structure of the original schists, and is by no means uniform in composition-at one point, for example, blende may predominate, and a few feet farther on the body may become highly pyritic.Owing to the intimate association of the mineral constituents of the ore, it is very difficult to separate them from one another.Although this remark applies to ore from all parts of the field, the difficulty is particularly noticeable with Rosebery ore, the minerals of which are more intimately mixed, and are of smaller grain size than are the minerals of the Hercules ore.To effect a reasonably clean separation, it is necessary to grind the ore so that 90% passes a 200-mesh I.M.M. screen. Microscopic examination of the crushed product shows that 85% of the minus 200-mesh material is less than 30 microns in diameter, or, in terms of screen sizing, is minus 400 mesh. Particles under 30 microns are found to consist, of one mineral only, but in particles over this size separation has not always been effected. For instance, it is known that part of the galena and of the pyrite in the zinc concentrate is associated with sphalerite, and that part of the galena in the mill residue is associated with pyrite. There is only slight association between the minerals in the lead concentrate.

Jan 1, 1927

By G. S. Scott

In the course of tire investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, come attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rise if the rate of generation of heat exceeds the rate of heat dissipation and will fall if the opposite is the cane. Factors that affect the rate of generation of heat are:

Jan 1, 1941

By Hisataka Sakakibara

Although the pathophysiology of vibration-induced white finger (VWF) is still under discussion, evidence has been accumulated to understand the underlying mechanism. VWF is pathophysiologically characterized by an enhanced vasospastic response to cold, which can result from an imbalance between vasoconstriction and vasodilation in the digital arteries in response to cold (i.e., vasoconstriction-dominant). The imbalance is supposed to be due to faults in vascular vessels and sympathetically mediated vascular tone. Enhanced vasospastic response to cold Narrowing of arterial lumen with medial smooth muscle hypertrophy. Possible functional factors for enhanced vasoconstriction • Increased sympathetic nervous activity to cold (e.g., norepinephrine) • Increased release of endothelin-1 (ET-1; an endothelial-dependent vasoconstrictor) from the endothelium • Increased reactivity of alpha2-adrenoreceptors to cold Possible functional factors for decreased vasodilation • Decreased release of nitric oxide (NO; an endothelial-dependent vasodilator) from the endothelium • Decreased release of calcitonin gene-related peptide (CGRP; a vasodilatory neuropeptide) from sensory afferents The question is how their interrelations or imbalances among them are Vibration and arterial damage The next question is, how does hand-arm vibration exposure induce such pathophysiological changes in VWF patients? Recent morphological evidence from animal experiments shows that vibration acceleration stress (including shear stress) and smooth muscle contraction contribute to arterial damage of smooth muscle and endothelial cells. The vibration-induced arterial damage is frequency-amplitude-dependent.

Jan 6, 2006

By R F. Hoeberling

"The use of ground penetrating radar (GPR) for geological purposes has been underway for almost two decades. The commercial need for a versatile GPR that can rapidly identify buried objects andunderground voids has been recognized and is an area of research that has already proved useful for several geological activities. Several types of GPR endeavors have been reported in the literature, including exploration of placer deposits (Davis, et al. 1985) and heavy metals (Hammond and Sprenke, 1991), improving oil recovery (Witterholt and Kretzschmar, 1984), investigating coal seams (Coon, et al., 1981), stratigraphic survey (Fisher, et al. 1992), Lunar soils characterization (Olhoeft, et al. 1975 and Strangway, et al. 1977), characterization of rock around mine tunnels (Cook, 1985), location of old mine workings (Scaife, et al., 1992), location of abandoned gas wells in coal seams (Kemerait, 1992) and survey of hazardous waste burial areas (Horton, et al., 1981). Coal seammapping has been developed using a related continuous wave, phase discrimination technique (Stolarczyk, 1990). As the technology for the radar equipment and the onsite computational power has increased, many new applications have become feasible. This article will describe the present status of the GPR technology and indicate some of the exciting possibilities for nearterm prototypes now being constructed."

Jan 1, 1994

By H. A. D. Kirsten

Shotcrete has become a strategic component of support in underground mines. The ductility of reinforced shotcrete makes it a safe and economic means of surface support under adverse static and dynamic loads. The ability of ductile shotcrete to sustain load at large deflections enables excavations in squeezing conditions to be stabilized and the safety in excavations subject to rock bursting, to be assured. A Shotcrete Working Group was formed to find the configurations of fibre reinforcement that would give shotcrete the same ductility as when reinforced with mesh. Beams and panels reinforced with various types and lengths of fibre were accordingly tested. A single mix design consisting of river sand, ordinary Portland cement, fly ash, condensed silica fume and gunite dust and segregation suppressant was used. Steel and polypropylene fibre varying in length from 25 to 50 mm were used in nominal contents of 5 % and 0.5% by mass respectively. Beams, panels and control specimens were shot into specially made formers. Suitable mixing procedures were developed for the different types of fibre. The test specimens were shot in a semi-dry mix process. The shotcrete was cured until tested 28 days after shooting. The fibre contents and uniaxial compressive and Brazilian tensile strengths of the shotcrete were determined from the control specimens. The beams and panels were tested in bending in specially manufactured test rigs. The beams were examined for simple supports and fixed ends. The panels were fixed in a manner that simulated underground conditions and were loaded statically under uniform pressure. The beams were loaded and the corresponding deflections measured up to failure. The panels were loaded up to mid-span deflections of 150 mm. The results are presented in the form of load-deflection graphs. The peak loads and ultimate deflections for the fixed end beams were considerably larger than for the simply supported beams for the various types of fibre considered. None of the beams tested, however, were able to sustain load at relatively constant value beyond the peak load. The panel tests showed that 40 mm and 50 mm long steel fibre and 30 mm, 40 mm and 50 mm long monofilament polypropylene fibre reinforcement gave shotcrete the same ductility as mesh.

Jan 1, 1998

By S. Z. Pethö

Pillar extraction at shallow depths with small pillars that were not originally intended for secondary extraction can provide a huge benefit to the coal mining industry in those areas where a significant percentage of the remaining coal reserves are locked up in small pillars at shallow depths and where opencast mining methods are simply not as cost-effective and practical to implement. A system considering all of the pertinent geotechnical and mining aspects for the safe and efficient pillar extraction of small pillars at shallow depths at Xstrata Coal South Africa (XCSA) has been further developed and implemented as part of an ongoing improvement process addressing all of the relevant legal and associated risk aspects. This work follows on from the previous pillar extraction work carried out at the ATC, Boschmans, and Spitzkop Collieries. The process involved a number of in-house workshops and sessions arranged with all key personnel from Tavistock Colliery, and also included Professor Nielen van der Merwe of the University of the Witwatersrand, a world renowned authority on pillar extraction, towards reviewing and developing the Modified NEVID pillar extraction system employed previously at Boschmans Colliery. The system is currently being employed at Tavistock Colliery with success and no major accidents, with around 655 000 t of coal having been successfully extracted from the pillar extraction panels.

Jan 1, 2012

By Charles Pol Vuillier

Piling work for modification to the Charles Grimes Bridge in Melbourne, Australia required piles to be installed through 15 to 20 m thickness of very soft to soft silty clay overlying 10 m of stiff clays and sands in turn overlying siltstone. The presence of an old sewer founded at depth in the soft clays demanded that vibrations be kept to a minimum. Two pile type were used by Vibro-pile (Australia) to provide the client with the most economical piling price. The two pile types were CFA piles of 750mm diameter founded in the weathered rock and a full displacement concrete injected screw pile developed by Vibro-pile called the "Z" pile, founded on the rock. The development and features of the "Z" pile are briefly discussed, including the perceived applications and advantages of the pile type. On board instrumentation comprising a computer was used to monitor all aspects of the construction. The rig instrumentation provided an important quality control measure that gave confidence in the pile installed. Pile performance was proved on the cast in situ piles by dynamic load testing methods. Initially tests performed with a 120 kN drop hammer, which was not capable of mobilising the required loads. The performance was then satisfactorily proved by using a drop hammer of 20 tonne mass delivering blows drop heights of 1.5m. Low strain integrity tests on a number of piles were also used to confirm the structural integrity of the piles.

Jan 1, 2000

By R. G. Garrett, A. J. S. Geddes

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The 1986 geochemical survey was successful in recognising all the previously known mineral occurrences of significance in Jamaica, in outlining areas not previously believed to have mineral potential and in stimulating fresh appraisals of old occurrences in terms of their potential for new commodities. This has resulted in a very significant increase in mineral exploration activity in Jamaica

Jul 1, 1991

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915

By J Dwyer, M Hill

Downer’s mining division has made an operational and financial commitment to developing engineered solutions that mitigate the risks associated with operator proximity to uncontrolled development drill boom movements, and unguarded rotating drill steels.With the potential for serious injury or fatality, these identified risks are categorised as critical. Previous attempts by the industry to engineer them out have produced limited success, with numerous incidents still occurring year on year. Ultimately, the industry (as a whole) remains reliant on procedural prevention for operator safety.Downer understood the success of such an initiative would largely depend on the effective collaboration between operational experience, technology experts and automation. With so many variables requiring consideration; such as physical operator movement, machine boom movements, variable machine positions, and underground environmental impacts – challenging traditional technologies was necessary to deliver an optimal solution.For that reason, discrete detection (similar to laser curtains or beams) was considered not fit for purpose. The use of situational mapping, using rotating lasers, however, provided the optimal solution. The lasers collect data that is then processed using a custom software application.The software application is specifically programmed for tracking and classifying objects within detection zones, using advanced algorithms and filtering. Recognition and removal of non-positive disturbances are possible without losing personnel detection capability. The detection of relevant classified objects (humans) is determined by analysis of object size, age, movement, and speed etc. When the relevant object is detected, an alarm and inhibit function is applied preventing drilling functions.Any breach of the safety zone (forward of the front jacks) will automatically disable the hydraulic boom function. This can only be reset in the cabin once the person or persons have returned past the front jacks of the development drill into the safety zone.Downer, in collaboration with partner YUMARR Automation, has successfully developed this reliable boom isolation system, and is called JumboGuard. The system has now been commissioned and installed across all Downer Mining development drill fleets, operating in Australia.CITATION:Hill, M and Dwyer, J, 2017. JumboGuard – automatic boom isolation system, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017