Search Documents

By W. A. Burns

Vertical flow is an important mechanism in many petroleum reservoirs. Yet no adequate method has heretofore been proposed for determining the in-situ vertical permeability in a reasonable length of time. Core measurements of vertical permeability do not necessarily represent effective in-situ values. Cores may be representative of only localized pockets of high or low permeability, and total reliance on cores might cause one to overlook the presence of vertical fractures altogether. Conventional single-well tests, interference tests, and pulse tests commonly are used to determine horizontal transmissibility, khh/u, but generally are not designed to measure vertical trans-missibility or other groups containing vertical permeability, ku. A new well test described here provides a measure of in-situ vertical permeability as well as the previously measurable horizontal permeability. This "vertical test" determines the vertical diffusivity, kv/gcu, and horizontal transmissibility, khd1/u (where dl is the length of injection or production perforations). The test is basically a short-term interference or pulse test normally lasting less than a day. Conventional down-hole equipment is used between two isolated sets of perforations in the same well, as shown in Fig. 1. A "layer-cake" description of a reservoir can be obtained by running two or more vertical tests in the same well, each over different vertical intervals. Each test can be analyzed for the effective vertical and horizontal properties of the interval tested. In addition, a vertical well test can determine the effective- ness of a shale barrier or tight zone by testing across it. Field use to date of vertical testing has confirmed its utility in reservoir description. Mathematical Basis Interpretation of vertical tests for ku and kh is based on comparison of measured pressure response with computer-generated response. Pressure behavior during a vertical test in a homogeneous, anisotropic, infinite-acting reservoir (infinite in radial extent and bounded in both directions vertically) is given by the diffusion equation for slightly compressible fluids with negligible gravity effects.l A schematic diagram of the problem is presented in Fig. 2, and an analytic solution, based on the image

Jan 1, 1970

By Gregg A. Scott, Gordon F. Revey

"The Folsom Dam is a 340-foot-high concrete gravity dam with embankment wing dams located on the American River about 20 miles northeast of Sacramento, California. Folsom Dam is operated andmaintained by the U. S. Bureau of Reclamation (Reclamation). As part of the Central Valley Project,Folsom Dam is a multipurpose facility providing water supply storage, flood control, power generation, and recreational opportunities."

Jan 1, 1999

By Gonzalo Chávez

El presente texto describe la lixiviación de oro con tiourea como una alternativa viable para la recuperación de dicho mineral, así como para el medio ambiente. En este sentido, la lixiviación de minerales de oro con solución ácida de tiourea fue evaluada con el uso de carbón activado, re-extracción y electrodeposición, obteniéndose velocidades de reacción y recuperación similares a los obtenidos con cianuro.

Sep 12, 2011

The nature of the specialty glass and ceramic business magnifies the dependency of the ultimate product on the unique properties of their raw materials used to make them. This dependency has implications in the management of risk in the supply process which requires a special procurement organization and program commitment to be successful. The Coming system of managing critical materials and factors in development of alternate new suppliers and products is discussed.

Jan 1, 1989

By Paul Gauthier

Aujourd?hui, avec un faible prix de l?or sur le marché, les opérateurs miniers doivent revoir leur façon de faire. La méthode de minage «Eureka» permet de réduire les coûts de production et d?accélérer la mise en production des chantiers. Les principales étapes du cycle de minage et les problématiques associées à l?utilisation de cette méthode à la Mine Bousquet y sont décrites.

Oct 1, 2001

ALTHOUGH great progress has been made in flotation of the Broken Hill silver-lead-zinc ores, no paper dealing with this subject has been presented to the members of the Institute since James Hebbard's valuable contribution in 1913. Almost every discovery or development in the history of flotation has formed the basis 6f a patent, and but few experimentalists have overlooked the fact that their investigations might lead to the establishment of a patentable process. This, together with the aftermath of patent litigation, naturally resulted in secrecy being maintained in matters appertaining to the art, and the industry as a whole has consequently suffered considerably. Much valuable time has been wasted through numbers ofmen repeating work along certain lines, which, unknown to them, had already been thoroughly exhausted by others, whereas a lot of this would have been avoided by a freer interchange of information amongst those directly concerned. Owing to differences in the ore treated and the various applications of flotation concentration in relation to gravity methods, the flotation problems of the various mines differ considerably. This, together with the secrecy previously referred to, hasresulted in the development of numerous systems and machines, most of which would appear, to the casual observer, to comprise separate and distinct processes. The author has endeavoured to show how much these processes have in common with one another, and, at the same time, has tried to convey some general ideas on flotation to those members of the Institute who are not directly associated with this branch of concentration.

Jan 1, 1919

Gippsland has perhaps the most colourful history of exploration of any area in Australia. Hydrocarbons were first discovered in the Gippsland Basin in 1924 when a water well at Lakes Entrance encountered oil and gas shows. In 1942, the Commonwealth and Victorian Governments, in an effort to supplement a wartime oil shortage, sank a shaft near this well and produced 8000 barrels of low gravity oil up to 1956, when the field was abandoned. A total of 64 shallow wells had been drilled in the Lakes Entrance area by that time. Elsewhere in the onshore Gippsland Basin, 30 wells were drilled from 1925 to 1941. In 1960 BHP Ltd was granted an exploration permit covering much of the offshore area of the Gippsland Basin. Esso Australia Ltd joined BHP in 1964 and drilled the Barracouta-1 gas discovery in 1965. Since then over 100 exploration and appraisal wells have been drilled in the basin resulting in the discovery to date of some 3.6 billion barrels of recoverable oil and 8.8 trillion cubic feet of recoverable gas (Current remaining recoverable reserves are 906 million barrels of oil and 5.7 TCF of gas). Exploration in the offshore areas is actively continuing today and new discoveries are still being made.

Jan 1, 1992

By Robert Hopler

Some few years ago, when the cruiser “Brooklyn” was passing through the fairway to the southwest of the Battery, the ship being fully equipped with stores, etc., and therefore at her maximum draft, she grounded quite heavily upon some obstruction, and received injuries which necessitated her docking at the Brooklyn navy yard, where extensive repairs had to be made on her damaged bottom.

Jan 1, 2007

By A. L. Crandell

History The Cortez Mining District has a long history of mining activity dating back to 1862. More recently, Cortez Gold Mines had operated a cyanide leach, counter current decantation (CCD) recovery gold mill from January 1969 to February 1976. This type of plant has been standard in the US for treating higher grade, finely disseminated gold in Carlin type ores. The mill was initially operated from 1969 to 1973 at 1.5 kt/d (1650 stpd) on oxidized ore from the Cortez ore body. In 1973, the mill was operated at 2 kt/d (2200 stpd) on softer, less oxidized, high clay ore from Gold Acres, located 13 km (8 miles) west of Cortez, NV. In February 1976, the oxidized portion of the ore body at Gold Acres was depleted and the mill ceased operations. Successful heap leaching of the lower grade portion of the ores was practiced at both Cortez and Gold Acres to supplement the milling operations. Valuable experience was gained in the operation of these two heap leaching programs (Duncan and Smolik, 1977). The ore heaps at Gold Acres and Cortez were releached with a limited crew from 1976 to 1979. The surge in the price of gold in late 1979 sparked an interest to incorporate new techniques into treating lower grade and less oxidized carbonaceous ores at Cortez. In early 1980, heap leaching was started on low grade oxidized dump material left from the earlier Cortez mining operation. By June of 1980, testwork was completed on the London Extension Dump, a low grade, mildly carbonaceous dump at Gold Acres. It was decided to convert the mill at Cortez from the conventional cyanide leach CCD recovery plant to a carbon-in-leach (CIL) recovery system. In May 1983, ore processing from the Horse Canyon deposit began. The Horse Canyon ore body contains both oxide and carbonaceous ores and is located 22.5 km (14 miles) from the Cortez mill. The Cortez CIL circuit was expanded to handle a blend of oxide and carbonaceous ores from Horse Canyon. Ore selection In the last quarter 1979, gold prices were increasing to a point where restarting the Cortez mill, idled since 1976, appeared imminent. Several previously explored geologic reserves at various stages of development were available as possible sources of feed for the mill. Initial metallurgical testing of dumps and tailings from earlier operations was completed, and previously uneconomic deposits were explored. It was decided to pursue sources of ore with the least lead time to production and those with the least capital cost requirements. A master plan was developed to bring the four profitable ore resources into production. The plan called for: • Heap leaching of waste dumps from the Cortez mining operation; • Restarting the mill to handle the waste dumps from the London

Jan 9, 1986

The Misima open pit gold mine is a 20Mt per annum operation. Blasthole drilling is used to sample all material at a uniform 5m square pattern, and representative sub- sampling of the blast holes enables assay samples to be collected over the full 10m bench height. Samples are assayed for gold, silver and copper at the Company's laboratory at the mine site and the assays are provided to geologists as a written assay report and on floppy disc. Surveyed blasthole locations and assay results are transferred via personal computers (PCs) to a SUN mini-computer where results are stored by bench, blasthole assays are kriged, and plot files are created. A geologist selects grade boundaries from the kriged data, adjusting the boundaries towards the raw blasthole data where hard boundaries are recognised. Surveyors peg the resultant boundaries in the pit using a system of colour-coded pegs to display the different material types. A daily plan also shows boundaries and face positions.

Jan 1, 1991

By Manuel Caro

El presente trabajo describe el proceso de mantenimiento del equipo de aire denominado Optiair. Este filtro al tener una mayor capacidad de retención de polvo, permite que el equipo pueda trabajar por periodos más largos sin tener que detenerse para realizar el cambio de filtros, lo cual incrementa el factor de disponibilidad del equipo. Entre los beneficios principales tenemos: el incremento de salida de aire, menor restricción del flujo, menor caída de presión y una mayor cantidad de contaminante capturado.

Aug 25, 2002

By K. Morsi

Carbon nanotube (CNT) reinforced metallic composites have been recently generating significant scientific interest, due to their expected superior properties compared with other composites. Out of the metallic matrices investigated for reinforcement with CNTs, aluminum has received considerable attention. A major problem has been the dispersion of CNTs in metallic matrices. This paper discusses preliminary results on the mechanical dispersion of CNTs in aluminum powder, powder processing, stability and characterization of aluminum dispersed with CNTs at reinforcement levels equal to and below 5 wt.%.

Jan 1, 2009

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By J. Sikamo, A. Mwanza, C. Mweemba

"The Zambian copper mining industry as we know it today had its genesis in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production rising to a peak of 769 000 t in 1969, providingover 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level in the year 2000 when production was 250 000 t. An average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000.Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and after more than US$12 billion investment, production levels increased year-on-year to a peak of 763 000 t in 2013 with direct jobs reaching 90 000.This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support for other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings, and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies, and human capital. This is looked at particularly in the light of current challenges the industry is facing. Suggestions are proposed on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2016

By A. J. Monhemius

"This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a “hydrometallurgical copper smelter” will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.RÉSUMÉ Cet article passe en revue l’histoire des procédés modernes de contrôle du fer en hydrométallurgie. Il accordera une attention particulière aux procédés développés dans l’industrie du zinc électrolytique pour l’élimination du fer dans les liqueurs lixiviantes de sulfate de zinc anhydre, ainsi qu’aux problèmes rencontrés par l’industrie en termes d’élimination sans danger des résidus ferreux générés par ces procédés. En projetant les leçons tirées du passé sur les efforts actuels, on pourra développer des procédés hydrométallurgiques pour le traitement de concentrés de sulfure de cuivre. Beaucoup prétendent que toute tentative de créer une « fonderie de cuivre hydrométallurgique » échouera à moins de développer des méthodes permettant de récupérer le fer sous une forme pouvant directement être utilisée par les industries sidérurgique ou des pigmentsINTRODUCTIONThis paper resulted from an invitation to the author from the CIM’s Historical Metallurgy Committee to give a presentation on the early developments of iron control in hydrometallurgy. This was to take the form of a plenary lecture at the 4th Symposium on Iron Control in Hydrometallurgy, which formed part of the 28th International Mineral Processing Congress, held in Quebec City in September 2016.I was naturally flattered that the invitation was to give the lecture at an IMPC, the prestigious conference series that has been held since the 1950s. That this particular IMPC was to include the 4th Symposium on Iron Control in Hydrometallurgy, a conference series held only every 10 years, made the invitation even more appealing and appropriate. This was because I had been co-chairman of the First Symposium on Iron Control, together with my erstwhile colleague, John Dutrizac, which was held 30 years ago in Toronto."

Jan 1, 2017

By Jr .. Ebbley

The investigation of mine shafts and underground workings at Leadville, Colo., was started in May 1946 and recessed in November 3, 1946. Thirty-eight shafts and connecting accessible underground workings, comprising about a third of the accessible shafts in the district, were investigated. The Leadville district, a former important producer of lead and zinc, was considered by the Bureau of Mines to be capable of bolstering 'the waning domestic output of .these important metal. Accordingly, the investigation was initiated for the purpose of. .obtaining more definite data on sulfide and oxide reserves, evidence to justify completion of the Leadville drainage tunnel, representative large samples of the complex oxidized and mixed ores for testing to determine methods, beneficiation factual data to be supplied to property owners in order to stimulate production, and to determine the more favorable areas for development by the Bureau.

Jan 1, 1949

By Yue-yuan Li

China has abundant magnesite resource, but the low-grade and powder ores have always been rejected, which influences the comprehensive utilization of resource and often causes circumstance problems. The present work investigated the preparation of magnesia whisker using magnesite tailings as starting materials by preparation magnesium carbonate whisker as precursor firstly in the route of calcination, hydration, carbonation and pyrolysis, follows by second calcination of the precursor. The influence of pyrolysis conditions and additives on morphology of magnesium carbonate crystal as well as the influence of calcination conditions on morphology of magnesia whisker was investigated. The results showed that thermal decomposition products was MgCO3?3H2O. Magnesium carbonate whisker with length of 10~60 µm and the length-to-diameter ratio of 10~20 was prepared when soluble magnesium salt was added. While temperature was elevated at 1°C?min-1, magnesia whisker with length of 10~60µm was obtained.

Jan 1, 2010

The beach sand industry is the only Australian mineral industry which, so far, has used electrostatic separation on a full commercial scale. The main application of the process is for the separation of rutile from zircon. Laboratory work has demonstrated that electrostatic methods are effective for ilmenite-monazite and cassiterite-zircon separations, thus facilitating the production of high grade monazite and cassiterite products from top-strip table concentrates, but the commercial application of these processeshas been rather limited so far. Overseas, electrostatic methods are becoming more widely used for the treatment of granular material which is not amenable to flotation. The use of electrostatic separation for the treatment of ores other than beach sands has been investigated in this laboratory 1, 2, 3, and two pilot separators were built during i953 to carry out field tests. Of these, the first was an inclined feed plate separator for the removal of silica from granular lime-sand in Western Australia, the second a conductance roll separator for the removal of diamonds from alluvial gravel in New South Wales. In both cases the whole of the ore passed through the separator, not a gravity concentrate only as in beach sand practice. The two types of separator mentioned are shown diagramatically in Figs. 1 and 2.

Jan 1, 1954

By James Westfield

Drilling for roof bolting has created a new dust problem for the coal-mining industry. Drilling is inherently dusty, and control of dust produced by drilling vertical or nearly vertical holes is much more difficult than control of that produced by drilling flat or down holes.4/ Also, the dust produced by roof drilling differs in composition from that produced by drill-fur, or cutting the coal face because it contains a significantly greater amount of free silica and therefore presents a greater potential hazard of silicosis. Roof bolting has been practiced successfully in the mines of the St. Joseph Lead Co. in southeastern Missouri for over 20 years, but it was not until 1947 and 1948 that large-scale roof-bolting experiments were conducted in coal mines.5/ Although the need for dust control in conjunction with roof drilling was recognized from the beginning, the development and acceptance of roof bolting progressed so rapidly during 1949 and 1950 that solution of the dust problem lagged behind other engineering phases of the technique.

Jan 1, 1951

By Both R. A, Daily B

The Patawarta Diapir, located in the northern Flinders Ranges (South Australia), has intruded into late Proterozoic Wilpena Group sedimentary rocks. The diapir contains disrupted blocks of a wide variety of rock types, most of which can be correlated with the Lower Callanna Beds of Willouran age, in a matrix of predominantly carbonate and siltstone breccia. Mafic rocks in the diapir appear to predate intrusion of the diapir. As with many other diapirs in the Flinders Ranges, copper mineralization is present in the diapir and occurs as narrow veins consisting essentially of carbonate with chalcopyrite and pyrite that formed after diapiric intrusion.Fluid inclusion studies demonstrate that the mineralizing fluid was a Na-Ca-K-Cl brine; probably derived by expulsion of interstitial water following emplacement of the diapir, with dissolution of evaporites within the Callanna Beds sediments and enrichment in copper by reaction with these sediments and associated basic igneous rocks. Mineral assemblages combined with fluid inclusion and geochemical data indicate a possible environment of vein formation of T ÿ 165°C, pH ÿ 4.3 ± 0.9 and log fO2 ÿ -47.3 ± 0.5. Sulphur isotope analyses indicate d34Sfluid ÿ 10 per mil, suggesting evaporites in the Proterozoic sediments as the major source of the sulphur but with some additional sulphur from an igneous source, possibly leached from the malic rocks of the diapir.

Jan 1, 1986