Search Documents

By G. Bierie

The conveying of bulk materials is prone to problems. These problems can reduce the capacity and efficiency of the plant, and even threaten the health and safety of the workforce. This presentation will look at new conveyor technologies systems, and how, used separately or in combination, they can improve material handling.

Jan 1, 2007

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By William D. Hissem

While much technology has been developed and brought to bear in the area of blasting applications, the foundation work required for success in the muck pile begins with the drilling program.

Jan 1, 1997

THE 125th meeting of the Institute was held in New York, Feb. 20-23, 1922, inclusive, and was the most successful annual meeting of the Institute ever held; there was a larger registration, there were more sessions of importance, and a greater number of sessions, than in any previous year. The total registration was 1331, comprising 351 New York members, 393 visiting members and 587 guests. At the annual business meeting of the Institute, held on Tuesday, Feb. 21, with President Ludlow presiding, there was a much larger attendance than usual. The report of the tellers was read and the following officers were declared elected: Arthur S. Dwight, Director and President-District 0 J. V. W. Reynders, Director and Vice-president-District 0 A. R. Ledoux, Director and Vice-president-District 0 Charles F. Rand. Director-District 0 George D. Barron, Director-District 0 William H. Bassett, Director-District 1 Thomas B. Stearns, Director-District 8 William Kelly, Director-District 5

Jan 3, 1922

By S. S. Peng, C. T. Holland

Mountain Top Removal (MTR) mining started in West Virginia nearly thirty years ago. This surface mining method can extract multiple coal seams as thin as a few inches thick with total recovery and minimum rock dilution in very steep mountainous terrain. It is highly efficient even if coal seams are in close proximity and small in aerial extent. Consequently, MTR has been widely used in the Central Appalachian Coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) for the past thirty years with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impacts on the surroundings in the history of MTR mining. However, in the past two years the debate over the MTR mining has grown quickly and in times become very intensely. This paper describes chronologically the issues raised by various parties, legal actions, its impacts on mining permit application and research projects developed to address the issues.

Jan 1, 2000

By B. Anameric, S. K. Kawatra, K. B. Rundman

The iron nugget process is an economical, environmentally friendly, cokeless, single-step pig iron making process. Residence time dependent process requirements for production of pig iron nuggets at a fixed furnace temperature (1425 C) were investigated. Three chemically and physically different products were produced after complete reduction to iron, depending on the residence time in the furnace. These products were direct reduced iron (DRI), transition direct reduced iron (TDRI), and pig iron nuggets (PIN). The increase in the carbon content of the system as a function of residence time was detected by optical microscopy and Microhardness measurements. Sufficient carbon dissolution for the production of pig iron nuggets was obtained after 40 minutes residence time. The pig iron nuggets produced had chemical and physical properties similar to blast furnace pig iron. They were liquid state products and slag was completely separated from the metal.

Jan 1, 2005

By Ralph E. Burnham, Jeff Taylor, Jonson Montgomery, J. Kelly Ratliff, Rennie Montgomery, Martin Brashear

Top priorities for all blasting companies and individual blasters are risk management, safety of company personnel and the general public, regulatory compliance, and liability protection. On a daily basis, hundreds of shots are detonated by well-trained, skilled, and experienced blasters without incident. Unfortunately, accidents inevitably occur, which is why blasting is considered an “ultra hazardous” or “inherently dangerous” activity from a legal perspective. Despite countless regulations, recent advances in technology, improved training, ongoing research, and improved communication in the industry, mistakes and the resulting incidents continue to occur during blasting operations. These result in dangerous or deadly flyrock, site security lapses, increased complaints, blast damage claims, and lawsuits, which lead to increased insurance costs and other financial tolls for blasting companies. In life, lessons learned the hard way are rarely forgotten. The same is true in blasting operations. Blasting missteps and the resulting events are often the best catalysts for improving risk management and thereby reducing accidents, liability, and financial tolls. This paper provides a summary of two incidents, one safety and the other liability related, and the errors that resulted in a fatality in one case and a multi property lawsuit in the other. The two incidents provide examples that serve as a case study for lessons learned the hard way in blasting operations and offer guidance for the considerations that blasters and blasting companies should incorporate into daily operating procedures.

Jan 1, 2018

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong Operational Readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.The road blocks encountered are often from systems that one assumes will operate without trouble such as air-conditioning, or design assumptions that were taken years earlier in feasibility process stages, namely the capacity of existing systems that will connect the new plant to the existing facilities. The challenges associated with rectifying these issues in addition to the requirements to properly start-up and operate a new plant without impacting production are great, and it is imperative to have the necessary resources to react quickly to any problems.IntroductionCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary by-product of the process."

Jan 1, 2016

By Lee T. J

The area, A, under a gamma-ray log that passes through a horizontal bed given by: A = gl/k. Here is the equivalent concentration of U3O8 in the body, l the thickness of the body, and k the calibration factor or sensitivityof the logger. The area is independent of the logging speed or logger time constant.This relationship, together with the first moment about the maximum of the log and its value there suflicient to determine the thickness, position of the centre of the bed from the log maximum and the concentration of U3O8.Numerical results obtained from artificial and field data show that the computed results arc as good as those obtained by methods such as the inverse filter technique and the iterative method. The present method yields results that arc easier to feed into an ore reserve data base.

Jan 1, 1981

By Moinpour M

The kinetics of reduction of copper (cuprous) sulphide with CO-CO2-He gas mixtures, using an excess of CaO(s) as a sulphur-scavenging substance were investigated in the temperature range 855° - 950°C by a thermogravimetric method. Several gas compositions were employed at each temperature. Potential carbon deposition was overcome by preheating the reducing gas mixture. The phase-composition and the morphology of partially reactedsamples were analysed by a SEMlEDAX unit. The reduction rates showed strong dependence on the bulk gas compositions (CO, CO2) and, in most cases, the rate declined with rising temperature. The rate-controlling step appears to be the diffusion of CO2 gaseous species through the micropores of the CaS(s) - product layer which builds up around the CaOcore.

Jan 1, 1989

Adsorption of Alkylammoniums in the Interlayer of Montmorillonite and its Effect on the Viscosity of Organo-Montmorillonite Gels

Sep 13, 2010

By Marilia S. de Magalhaes

Keywords: sinter, characterization, agglomeration, iron ore Iron ore sinters are the main burden of blast furnaces for pig iron production. The evaluation of these agglomerates is very important due to their properties affect indirectly the productivity and costs of production of the steel industry. In the sintering plants, the standard procedure of sinter assessment has been carried out by particle size control, bulk chemical analyses, tumbler and/or shatter tests and determination of reduction degradation and reducibility indexes. Microscopy techniques have just been applied to characterize sinters produced in pilot conditions, however, these techniques, the classical ones and the less traditional, allow enhancing the industrial sintering process assessment. For investigation of the phases, microstructures and fabric, reflected-light and scanning electron microscopy(backscattered electrons images) were used; for micro analytical chemical examination, energy-dispersive X-ray spectrometry; for Kikuchi patterns registers, electron backscattering diffraction. In addition to the microscopy techniques, the magnetic behavior was depicted by means of magnetic susceptibility measurements. Iron ore sinters are made up by hematite, magnetite, silicoferrite of calcium and aluminium and silicates. These phases develop either during sintering or, in some proportion, represent remnants of ores and fluxes; this is the case of some hematite and Mg-bearing silicate, respectively. From the magnetic susceptibility results, three different behaviors were determined, which are directly related to the magnetiteproportion in the samples. The phase association and proportion, the sintering conditions andthe quality assessment are some features appraised by such procedures, which reveal themagnitude of this proposal in sintering plants.

Jan 1, 2005

By Steve Jones

Minor subsidence damage to the Burgettstown Junior-Senior High School building and grounds near Burgettstown, Washington County, Pennsylvania, prompted an investigation of the site in early 1985 by the Bureau of Abandoned Mine Reclamation of the Pennsylvania Department of Environmental Resources. The investigation determined that subsidence over an abandoned coal mine was occurring and that additional damaging subsidence would occur if reclamation measures were not taken. A Pittsburgh Coal Seam Mine which was abandoned in the 1920's underlies the school at a depth of sixty-five (65) feet. This sixty-five foot section is comprised of five (5) feet of unconsolidated overburden and sixty (60) feet of thinly bedded, highly fractured shale. Approximately five and one-half (5-1/2) feet of Pittsburgh Coal was extracted at the school site. A thin shale binder and one (1) to one and one-half (1-1/2) feet of roof coal were left in place. Within the Contractor's Underground Working Area (See Figure 1) approximately thirty (30) percent of the coal was extracted. It appears that the mine was just being developed in the vicinity of the school when it was abandoned for no known reason. Other nearby portions of the mine show extraction approaching sixty-five (65) percent.

Jan 1, 1986

By S. J. Page, R. A. Jankowski, J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 1992

By V. Osterholt

Sustainable development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and require the use of stochastic conditional simulation technique. This paper considers three methods for simulating orebody geology: (1) pluri-Gaussian simulation that limits the allowable contacts between the various units; (2) sequential indicator simulation using indicator kriging; and (3) an experimental multiple-point approach that captures some higher-order spatial statistics. The data requirements of the methods, how to meet them in mining applications, and performance characteristics are discussed. The application of these methods in a hypothetical deposit consisting of three geological units provides a comparison and illustrates the advantages of the different simulation approaches.

Jan 1, 2005

By D. Jacobson

There are many different machine setup parameters and variables that affect the production of cone crushers in a mineral processing plant. One of these variables is the eccentric speed at which the cone gyrates. In June 2012, pilot tests were conducted on a 200 hp high speed cone crusher to determine the production and operating conditions over a wide spectrum of eccentric speed. Every plant will have variations in the ore characteristics and feed rates throughout the life of the mine, and at times throughout a single shift of operation, which result in non-optimal use of the crushing energy and inconsistent process control. For high speed cone crushers, the crusher will exhibit a different capacity, power required, and discharge size distribution as the speed ranges over the design limits of the machine. This study documents the measured variation in production and energy efficiency both when the crusher was ran at full capacity as well as when the feed to the crusher was not sufficient to run at full capacity. Overall, the results match theory and the capacity and power fluctuated by 25% and 17%, respectively, over the speed range when operated full while there was an overall trend of slightly coarser discharge size distribution as the speed decreased. The results with the fixed feed rate were more telling, as the crushers had 4-14% higher production when making a theoretical minus 12.5 mm product when operating at the optimal speed as compared to the worst speed in the ?typical? speed range for this application. Secondary analysis of the fixed tonnage testing also showed that the power draw was more consistent with lower magnitude spikes at the higher speeds (higher cavity level), as on average the standard deviation of the power draw increased from 7% to 18% and the peak power spikes from 20% to 48% over the speed range tested. The findings lay groundwork for more efficient plant design. Varying the speed of the crusher can be used to tune the crusher speed during commissioning, adapt to changing ore conditions over long periods of time, or be used as a dynamic input into an advanced control system. Each action above would serve to make the crusher(s) more productive and more energy efficient, and would also have mechanical benefits for the machine. Key Words: cone crusher, ore reduction, process control, crushing efficiency

Feb 27, 2013

By Andrew L. Peterson

CATOH Inc. of Weedsport, New York recently completed a very challenging Bored-In Pile project which features unique construction techniques in the installation and load testing of 45 and 100 ton capacity piles. The bored-in piles were installed on a twenty-nine million dollar New York State Department of Transportation project which began in the fall of 1995 and ended in March of 1997. The project included the construction of 5 new bridges to alleviate a very congested traffic network which had come to be known as the "Octopus" in the small city of Ithaca, New York. CATOH Inc. was awarded the piling contract by general contractor Santaro Industries in the fall of 1995. Piling installation work was completed in March of 1997. BACKGROUND The project is located at the southern tip of Cayuga Lake which lies in the heart of Upstate New York's Finger Lakes Region. This region is popular not only for wine making and vacationing, but also for its impressive geological history. The glacial activities that helped to form the deep valleys of this scenic area are also responsible for creating challenging underground conditions for deep foundations work. CATOH developed two pile designs to accommodate differing site conditions on the project. Internally reinforced piles were developed for use in the center of the valley and externally reinforced piles were developed for locations close to the valley wall.

Jan 1, 1997

The Zeehan field has yielded over 190 000 tons of lead and 26,000,000 oz of silver. Moh of the production took place between the initial discovery of silver-lead ore in 1882 and 1920, and the greatest part was extracted from fissure lodes in the Proterozoic to (?) lower Cambrian rocks. It is demonstrated that the prosperity of the mines relied upon the silver content, which is apparently highest in these beds, particularly where spilitic rocks are associated with them. In contrast, galena occurring in orebodies emplaced in the Gordon Limestone is low in silver.Most of the workings are relatively shallow due in some cases to enrichment related to erosion surfaces.Fault zones within a complex anticlinal structure exposing the Proterozoic to (?) lower Cambrian formations appear to have been major factors in the control of mineralization.

Jan 1, 1968

By Cosmin Carpinisan, Erich J. Hofmann, Stephen J. Hall

"Since presenting a technical paper regarding their unique capabilities in Forged Steel Mill Gearing at the SAG-2006 Conference, Australian heavy engineering company Hofmann Engineering has pioneered a number of new manufacturing processes and design concepts for components of large comminution equipment. These include: 1. Novel design improvements for HPGR Rolls with forged steel tyres and a unique patented tungsten carbide insert designed to improve wear life, enhance autogenous layer build-up, and to reduce breakage & chipping under load. 2. Development of forged fabricated Mill Heads using rolled & welded high-tensile steel plate as alternatives to cast conical mill heads. 3. Insitu Girth Gear measurements for profile and wear via portable 6-axis CMM. 4. Gear and Pinion designs to AGMA-6114 for SAG mills of 38’-40’ diameter to 24MW and for Ball Mills of 26’ diameter to 18MW. The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering, combined with news of their new gear manufacturing and gearbox overhaul facility in Canada."

Jan 1, 2012

By J Wesseloo and Y Kim, Y Potvin, G Mungur, D Grant

At the previous MassMin conference held in Sudbury in 2012, the authors proposed a new framework going beyond dilution and equivalent linear overbreak sloughing (ELOS) for stope reconciliation in relation to the planned stope design. More specifically, the new process investigates performance outcomes including rock overbreak (OB) and fill overbreak (FOB), rock underbreak (UB) as well as geomechanical and operational aspects such as blasting, fragmentation and other production data.Based on the findings of the original 2012 study, a comprehensive data gathering program has been undertaken involving design and reconciliation data from 43 stopes mined between September 2012 and October 2014 at BHP Billiton’s Olympic Dam (OD) operation. The new database structure was based on four types of data:stope definition and performance datastope geometrygeotechnical parametersoperational parameters.The new database allows a more in-depth investigation of stope performance. It is now possible to quantify and analyse UB and OB performance from each wall individually as well as the crown. In this paper, the influence of several parameters on recent stope performance at OD is analysed. The underlying reasons for stope wall performance outcomes are discussed in this paper.CITATION:Potvin, Y, Grant, D, Mungur, G, Wesseloo, J and Kim, Y, 2016. Practical stope reconciliation in large-scale operations part 2, Olympic Dam, South Australia, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 501–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016