Search Documents

By P González, J Videla, E Córdova, I Gottreux

Currently, underground mining of deeper massive deposits with lower grades, harder rock conditions in high strength environments, entails difficulties in caving, fragmentation and seismicity of the orebody.So far, the use of preconditioning (PC) with hydraulic fracturing (HF) has shown positive results in terms of seismic response and caving performance, while PC combined with explosives aims to weaken the rock mass, causing an additional effect on fragmentation.In particular, mines commonly referred to as ‘supercaves’, operated by caving methods, have the need to integrate mine to plant processes, where rock fragmentation appears as a key tool. In fact, it implies making mining and comminution processes more efficient to the plant and for mines, it justifies the search of innovative solutions in drilling and blasting techniques to precondition the rock mass. The following paper aims to show the feasibility of numerical blast modelling to weaken the rock mass using explosives, mainly through sensitivity analysis applied to designs to minimise bias and uncertainty in the results. It is shown how the presence of structures, their geometry and in situ stresses influence or interfere with the PC method being used.From the work, it is concluded that better knowledge on the application of explosives weakening allows specialists to strengthen numerical models associated with every design and therefore previously validate their applicability, helping to understand complex phenomena such as the propagation of mechanical waves in non-elastic heterogeneous media. In this sense, it is understood that while there are studies (Sanchidrián, Segarra and López, 2006) showing that the transfer of energy in the rock mass could be even greater in a confined environment, the more competent rock mass and higher in situ stresses interfere mostly on the effectiveness of a technique using explosives.CITATION:Gottreux, I, Córdova, E, González, P and Videla, J, 2016. Preconditioning modelling and explosives effectiveness in block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 683–688 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R Cunningham

The E26 Lift 1 North Project took 37 months from the approval on 1st January 2019 to the commencement of production on 1st March 2022. This was five months ahead of the feasibility plan. When compared to the previous E48 Block Cave construction 12 years prior, which was of a similar size and design with ten extraction drives, crusher and conveyors, the E26 Lift 1 North project has been delivered at 29 per cent less capital cost. Key metrics achieved by the project include 12.7 km of development, 240 km of production drilling for drawbells and undercut blasting, 107 drawbells fired ready for production as well as only three Lost Time Injuries compared to 16 during E48 construction. The Lift 1 North Project Team has established a significant point of difference with the delivery being completed by the ‘Owners Team Model’ not Lump Sum or Turn-key. E26 Lift 1 North is now supplying the Northparkes processing plant for the next eight years. This paper discusses major milestones achieved throughout the process, modifications to processes from previous block cave construction at Northparkes as well as novel approaches to work to achieve the successful delivery of the project.

Mar 29, 2023

By W. G. Diamond

Lightweight aggregates have become increasingly important to the construction industry. From 1953 to 1960, the quantity of the aggregates used in concrete block, precast and prestressed concrete, and monolithic structures increased about 92 percent. The present study was conducted in Bureau of Mines Area IV which encompasses the South-Central States of Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas. This is an administrative area and does not delimit a market area or imply an economic unit. Because of the increasing importance of metropolitan areas in evaluating economic growth, significant data showing relationships between growth of the metropolitan areas and the lightweight aggregate industry are included.

Jan 1, 1964

By Donald B. Lindsay

This report presents the findings of an investigation into the characteristics of a number of techniques for cleaning ambient air with special emphasis on their applicability to the removal of the short-lived radioactive decay products of 222-radon, the so-called " radon daughters" that have been identified with the induction of lung cancer in underground uranium miners. The purpose of the study was to review the requirements for control of radon daughter concentrations in mine air, and to examine all techniques whose feasibility has been demonstrated in principle and which in our judgment would be capable of meeting those requirements. The study has included a review of all pertinent literature, both technical and proprietary, on the subject of the control of miner exposure to the radon daughters and in the area of potentially applicable air cleaning technology. Information about the nature of the problem and about the experience of the uranium mining industry in applying air cleaning methods to its solution was obtained by visiting mines where such methods are in use, and by written correspondence and telephone conversations with other industry sources. Information on performance characteristics and costs of applicable air cleaning methods and equipment was obtained from the experience of our own engineering staff and by visits, interviews, and correspondence with manufacturers of industrial air cleaning equipment.

Jan 1, 1978

Discussion of the paper of R. J. COLONY, presented at the New York Meeting, February, 1921, and issued With MINING AND METALLURGY No. 169, January, 1921. R. J. COLONY (author's reply to discussion).-The work of Sosman and Merwin on the system lime-ferric oxide, mentioned by Mr. Rankin, was not overlooked. When studying portland cements and portland-cement clinkers petrographically, however, the lime-iron compound was difficult to correlate with the very definite dicalcium ferrite described by those investigators, which possesses such well-defined optical properties. In portland cements, the calcium ferrite (or ferrate?) is an indefinite, fuzzy, and generally amorphous, or apparently amorphous substance that is distributed interstitially with respect to the other grains, from which it was very difficult to derive any satisfactory results. For this reason, the writer, tentatively, chose to regard it as related to the aluminate, and assigned to it the composition 3CaO.Fe203, which may be incorrect, however, as Mr. Rankin suggests.

Jan 8, 1921

By G J. Delemontex, N J. Grigg

Pre-concentration of precious metal and base metal ore types is becoming more relevant with the discovery, development and operation of many lower grade deposits around the world. The fluctuations in metal prices expose many mines to risks especially dealing with low and variable ore grades.Pre-concentration, the process of concentrating the valuable metal into a smaller mass yield, effectively results in the introduction of higher feed grades to milling circuits. Gangue Rejection, the removal of lower S.G. waste rock from the circuit not only results in higher downstream grades but also potentially removes harder, non-valuable mineral, providing significant power savings within the circuit. The pre-concentration or ‘gangue rejection’ process offers a number of benefits when considering the treatment of marginal ore deposits, especially if it can be performed at a coarse crush size; these benefits include a reduction of the operating costs and the feed of more metal units to the mill.Gekko Systems has effectively utilized the Inline Pressure Jig (IPJ) to pre-concentrate the valuable metal, achieving high primary recoveries into a range of mass yields resulting in upgrade ratios between 2 and 10 times.This paper explores the benefits of pre-concentrating ‘marginal’ ore deposits prior to the milling circuit; the selective rejection of ore types that may affect either the recovery or comminution process, and also looks into the potential to effectively reduce the ‘cut-off’ grade when considering the mine planning process. Case studies of projects using the IPJ to pre-concentrate and reject gangue are also included.Pre-concentration and gangue rejection provide the potential to develop marginal ore deposits, thus providing higher grades, less gangue and more metal at a lower operating cost to producers.CITATION:Grigg, N J and Delemontex, G J, 2015. The pre-concentration of precious and base metal deposits using the Inline Pressure Jig – higher feed grades and more metal, in Proceedings MetPlant 2015, pp 296–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By David A. Newman

Barrier pillars created during mine development provide additional reserves during mine closure and can be the sole access to reserves previously abandoned because of mining height or out of seam dilution limitations. The safe and successful mining of barrier pillars requires a thorough knowledge of the magnitude and distribution of the vertical stress field in addition to the strength and physical properties of the coal, immediate roof, and immediate floor strata. Quantifying the vertical stress field is complicated by the combination of the overburden stress, abutment stresses transferred onto the barrier pillar from adjacent gob areas, and in multiple seam mining, stresses transferred from abandoned subjacent mines. These variables make the extraction and development of barrier pillar reserves a site specific consideration. Three case histories are presented in which barrier pillar development and extraction provides; i) an access point and the means to ventilate a large area of low seam reserves left by a prior operator after developing only the thicker areas of a multiple split reserve, ii) the means to increase total recovery of a deep, thick seam longwall reserve, and iii) opportunities for the development and retreat mining of a two mile long barrier pillar in thick seam reserves.

Jan 1, 1995

By James K. Richardson

STATISTICAL evidence shows that continued efforts made by Government and industry to make mining safer during the last two decades have had most favorable results. In the copper-mining industry an accident frequency of 146 per million man-hours worked in 1925 dropped 71 per cent by 1945 to 43. This downward trend was relatively consistent except for a high period in 1937 which was probably due to a resumption of large-scale operation with many untrained miners. The iron-mining industry showed a similar trend, but at the relatively lower accident frequency of 66, which dropped to 24 in 1945. The close relationship between the steel and iron-mining industries may be one reason for the lower accident frequencies, because the steel industry is noted for its greater recognition of the fact that safe working conditions are an important part of labor-management relations.

Jan 1, 1948

By Earl C. Herkenhoff

Editor's note: The subject of mining on the moon can generate a wide range of strongly held opinion, from those leaning toward the view that, ultimately, such activity is the destiny of mankind to those who believe that all suggestions for moon mining to date are unrealistic, wildly expensive and in the hands of people who 'know nothing.' MINING ENGINEERING herewith publishes some of the basic pros and cons on the subject of moon mining by writers who are among those holding strong views on the subject, with the hope that some of our readers may be interested in joining this debate. Every mineralogist and most mineral industry people were keenly interested in the examinations of the first moon rocks brought back by US astronauts in 1969. Suffice to say that the examinations revealed nothing exotic in the mineral makeup of the very limited rock samples. The rocks were generally of igneous type, dark-colored and contained some common, Earth-type minerals. There was, in Earth terms, above average TiO2 content, but they contained nothing of commercial significance by Earth standards. Therefore, interest in moon minerals rapidly faded. Years later, on Sunday, May 4, 1986, living in Reno, NV, this author was shocked to read a local newspaper article by the Dean of the Mackay School of Mines, University of Nevada, Reno, headlined, "Moon Mining Not Far Off." Considering that the announcement more or less coincided with a slump in our domestic mining industry, the immediate questions in a reader's mind

Jan 1, 1991

By F. A. Rutledge, J. J. Mulligan, W. H. Kems, R. L. Thome

"As a part of the United States Department of the Interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits f nonmetallic minerals accessible to the Alaska Railroad for use in building materials in the Alaska Railroad-belt area. The results of the investigations, to date, indicate that raw materials for the production of brick products are in plentiful supply as clay in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.Shale for the production of lightweight aggregate or Haydite occurs near mile 67 on the Glenn Highway, and preliminary tests give excellent results. Physical tests are new in progress on commercial-size concrete building units made with this aggregate. Another shale deposit in the same formation was located at mile 16 on the Matanuska Branch of the Alaska Railroad, and preliminary tests give comparable results.Natural lightweight aggregate in tree form of pumice and pumicite occurs in Katmai National Monument and has been used with excellent results in lightweight-building units in Anchorage and Fairbanks. These deposits will be investigated in more detail by the Bureau of Mines during 1952.One small perlite deposit near Healy, Alaska, showed excellent expanding properties, and the product compares favorably with commercial perlites being used in the States for plaster and concrete aggregates. Additional investigation by the Bureau of Mines to delimit the known occurrence and, if possible, discover others were planned for the 1951 field season.The pumice from Katmai National Monument also was considered for use as a pozzolan in pozzolan-portland concrete. Tests by the Bureau of Reclamation indicate that the pumice sample submitted by the Bureau of Mines would be satisfactory in strength development but is not outstanding. Natural activity is good and is greatly improved by calcination at 1,4000 F. Water requirements and shrinkage also are satisfactory. However, the material is ineffective in reducing expansion owing to alkali-aggregate reaction; and, if reactive aggregate is used to make concrete, it would not insure against excessive expansion. An attempt will, be made during the 1952 field season to delimit pumicite deposits along the Alaska Peninsula more amenable for use in pozzolan-portIand concrete.Because the Railroad belt has such a rigorous climate, insulation for new construction is of prime importance. Luring the Bureau of Mines, investigation of building materials all samples were submitted for chemical analyses as possible sources of raw materials for the production of rock wool, one of the best insulation mediums. Four areas having deposits of the required constitu¬ents were located as follows: Anchorage area, with Potter limestone and argillite; Cantwell-Windy area, with limestone and shale; West Fork of the Chulitna River area, with limestone and agrillite; and Homer-Seldoyla area, with Seldovia limestone and Homer clay. It was planned to take bulk samples of these formations and submit them for testing during the 1951 field season."

Mar 1, 1953

By Wern-Ping Nick Chen

Durability risks for underground facilities can be underestimated during design phase as compared to well-known geological risks. However, unclear durability requirements can result in construction schedule delay and change orders. Unlike bridges or buildings, a unified underground durability code or standard does not exist. This paper will provide a durability approach for underground facilities, including degradation modes, mitigations, and compliance measures during construction. In addition, this paper will address how to clearly specify durability requirements in a contract document to reduce disputes during construction and discuss key durability tests that are time consuming and will impact construction schedule if not timely planned.

Jun 23, 2024

By D. Kwietnewski

With all of the unknowns associated with tunnel construction, how does a contractor choose a roadheader? This paper presents a review of several models of roadheaders being used in today?s tunnel projects. The features of different models of roadheaders are presented and compared. Roadheader size and cutter power generally determine which roadheader is best for a particular job. We will also present a model for matching features of the roadheader to the anticipated ground conditions such that the most efficient machine is selected for the project.

Jan 1, 2011

By Romano J. Micciche

One of the largest scale uses of a multiple, high-strength steel bar tiedown system is described. Tiedowns were installed to resist hydrostatic uplift forces acting on a section of the Interstate Highway Route I-90 southern approach roadway to the Third Harbor Tunnel, in Boston, Massachusetts. Site specific information is discussed regarding design, testing, and installation of Tiedowns. Conclusions are presented regarding the overall performance of this system and the application of this type of tiedown system on future projects.

Jan 1, 1994

Organization Place Date 1919 American Chemical Society Philadelphia, Pa. Sept. 2-6 National Assn. of Stationary Engineers Huntington, W. Va. Sept. 8 American Peat Society Minneapolis, Minn. Sept. 22-24 American Iron, Steel Electrical Engineers St. Louis, Mo. Sept. 22-26 American Institute of Min. and Met. Engineers. Chicago, Ill. Sept. 22-27 American Steel Treaters' Society, First Annual Convention Chicago, 111. Sept. 22-27 National Exposition of Chemical Industries.... Chicago, Ill. Sept. 22-27 National Safety Council Cleveland, O. Sept. 29-Oct: 2 American Foundrymen's Association Philadelphia, Pa. Sept. 29-Oct. 4

Jan 9, 1919

By Beverly Cramp

In 1995, mining engineer Alain Gachet thought about using Earth-observation satellite imagery to search for precious minerals. The latest radar Earth-observation satellite, Canada’s RADARSAT-1, had just been successfully launched at the time, creating new opportunities for commercial applications. Gachet was working in Congo Brazzaville as an oil executive and general secretary of Elf Congo for the French national oil company Elf Aquitaine. He understood that the RADARSAT-1 launch promised new and cost-effective sources of data for mineral and oil exploration. “It was early 1996 before I ordered my firstRADARSAT-1 satellite images,” said Gachet. “I was first struck by the quantity of information delivered by the radar images. Linear structures and faults were clearly defined and subtle topographic features were tremendously enhanced,” he said. “It was ‘tree top geology,’ but this kind of information appeared to be key for finding new gold seams.”

Jan 1, 2003

By John E. Rourke, O&apos

This report documents the process of site selection, instrument installation, data acquisition, and preliminary data analysis followed to characterize the physical response of overlying strata to longwall mining. A system of surface, subsurface and mine level instrumentation was installed at the Allen Mine in Weston, Colorado where the overburden varied in thickness from 600 to 900 feet. Survey monuments, automatic-recording strain-meters, multi-point rod extensometers, inclinometer-extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. A preliminary analysis of the data acquired up until project termination has shown the system to be operative and strata response to be similar to that reported for other subsidence monitoring case histories. Recommendations for continued monitoring of the instrumentation systems are presented.

Jan 1, 1982

Between February and August of 1986, Dr Alfred Petrick visited New Zealand sponsored under a Fulbright grant administered by the New Zealand-United States Educational Foundation. The grant supported a research project completed by Dr Petrick having as an objective, the preparation of a preliminary economic evaluation of the mining of six Otago lignite deposits as a source of energy for steam power generation or in liquid fuels. The research is limited to consideration of preliminary geological and engineering data on the six deposits and to the time constraints of the Fulbright visit. This paper is a summary of the final Fulbright report. The complete report including the listings of the computer programs is available from the Otago School of Mines.

Jan 1, 1986

By WILLARD W. CUTLER

This bulletin reviews, in the light of recent experience, the use of production-decline curves in estimating the future production of oil from wells. It deals with the estimation of the reserves of recoverable oil in properties already producing or in those adjacent to them, takes cognizance of the physical laws governing expulsion of oil from oil sands, and shows how the production-decline curve can be made to utilize these laws in estimating reserves and rates of production. The valuation of oil properties should be based on the total amount of oil recoverable from a property by the methods in use, the rate of recovery, the cost of production, and the selling price. Numerous other curves besides those for reserves and rates of production may be formed from the production-decline curve and will present desired information in a convenient time-saving form. These curves also are described. Methods developed before the production-decline curve method was used are briefly discussed in order that the principles on which estimations of oil reserves are based may be made plain. The construction of curves and tables for estimating future production of individual wells and of average wells in most of the important oil districts of the United States is described and operating problems that may be solved by the use of production-decline curves are discussed. The bulletin does not deal with costs, oil prices, or the methods of evaluating oil properties. Many engineers have amply demonstrated the value of the production- decline curve method by forecasting within reasonable limits the production of many thousands of wells and tracts. The value of similar estimates depends however, on (1) the application of trustworthy methods; (2) the care and judgment of the estimator; and (3) the length and reliability of the records and the accuracy of ofher information used in estimating future production. When adequate records and information are available, experience has shown that It qualified engineer can forecast production far more accurately than has been deemed possible, except where the usual conditions governing the expulsion of oil from a sand have been radically changed by applying compressed air or by flooding with water, or, to a less degree, by using vacuum. In general, the production-decline curve method, though there are limits to its accuracy, is far more trustworthy than any other.

Jan 1, 1924

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer's perspective and from an equipment supplier's perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By D. Rahal, I. Shah, B. Hines, S. Reddick

"The development of stirred milling technology has proven to be an enabling technology in fine grained metallic deposits. The increased grinding efficiency allows for the economic size reduction required to produce saleable concentrates. This improvement has opened the door to retreatment projects such as reprocessing of historic gold mine tailings. Recently a VXP2500 stirred mill was installed at Casmyn Mining Zimbabwe Turk mine to allow the reprocessing of historic mine tailings. After commissioning, an extensive joint research project between Casmyn and FLSmidth Minerals was conducted to optimize the performance of the mill. This paper outlines the challenges encountered in the optimization program and the outcomes from the joint research project.INTRODUCTION The development of stirred mills has opened up many new opportunities to recover valuable minerals from refractory ores. Stirred mills have already been reported as an enabling technology for the processing of fine grained ores in lead/zinc applications (Pease, Young and Curry, 2005). Historically, conventional ball mills were unable to economically grind material fine enough to produce the required recovery or concentrate grade. This often resulted in the loss of valuable materials to the final plant tailings. The advent of stirred milling has now provided an opportunity which has both economic and environmental benefits, the reprocessing of historic mine tailings. Many tailings stockpiles now contain economic concentrations of gold because of the ability of stirred mills to efficiently and economically grind the tailings to liberation sizes. The primary advantage of reprocessing historic tailings is very low cost processing. Recovering the tailings is usually as simple as pumping the material into the reprocessing circuit. The disadvantage of reprocessing tailings is the low feed grade and greater difficulty in recovery valuable minerals at the same size distribution. The material has already been previously processed so fresh surface area or an increase in metal exposure is required. These are both provided by regrinding the tailings material."

Jan 1, 2014