Search Documents

By Paul Hosford, Tim Haldane

"The paper describes the fast-track development of the project from feasibility study through to detailed design and construction, highlighting the process adaptations for handling sticky ore and water management in a tropical environment, and subsequent commissioning and operating experience of the mine. The paper discusses the geological setting, the environmental and socioeconomic considerations in developing and operating a mining operation in an underdeveloped country and the logistical challenges involved in bringing a large capital investment into Central America.INTRODUCTIONGlamis Gold Ltd. acquired the San Martin project in Honduras as a result of its merger with Mar-West Resources in late 1998. Despite the prevailing low gold price environment at the time of acquisition, Glamis anticipated rapid development of the San Martin project due to the quality of the deposit and other positive factors.Following favorable exploration and permitting activities in the first half of 1999, Glamis prepared a Feasibility study. In October 1999, Glamis decided to proceed with the development of the project and selected Hatch to provide the engineering, procurement and construction management services for the project. The San Martin project was in full-scale commercial operation approximately 14 months after the receipt of Board approval, and by July 2001 the San Martin project was operating at approximately 150% of its feasibility design capacity."

Jan 1, 2002

By Scott Ellenbecker

The formation in Newmont Mining?s Phoenix Mine near Battle Mountain, NV contains high levels of abrasive quartzite as well as gold, copper and silver. Newmont started mining operations at Phoenix (formerly Battle Mountain Gold) three years ago and the planners knew they were working with a challenging geological formation. But as it turned out, it was more challenging than anticipated. Mine manager Mark Evatz said, ?Anything that touches Phoenix rock wears fast. The rock fights back here.? To contend with the hard conditions, Newmont uses Atlas Copco?s Pit Viper 271 (PV-271) blasthole drill. Because of the hardness of the rock, drilling at Phoenix requires hammer drilling and the mine uses Atlas Copco TD65 hammers with 171 mm (6.75 in.) bits. The mine?s PV-271?s are outfitted with a single 41 m3/min (1450 cfm), 2.4 MPa (350 psi), oil-flooded air compressor. Phoenix has six Atlas Copco PV-271 drill rigs plus an Atlas Copco DML and a DM45 midrange blasthole rig. The mine?s goal is to keep 3.6 Mt (4 million st) of muck in inventory to stay ahead of the shovels and support needed operational flexibility (ore control related). Drilling efficiency has been a continuous point of improvement since operations began at the mine. The single-pass depth capability of 16.5 m (55 ft) on the PV-271 helped with that. Originally, the plans called for 6-m (20-ft) bench heights, supported by 7-m (23-ft) drill depths, and time spent moving from hole to hole was eating up productivity. Drilling on that plan resulted in drilling an average of 14 m/h (47 ft/hour). When depths were changed to 13-m (44-ft) drill depth, supporting blasting of 12-m (40-ft) benches, they were able to use the single pass capacity of the PV-271. Performance increased to more than 18 m/h (60-ft/hour) an hour. Although the drill depth change largely supported the improvement, other aspects of continuous improvement associated with improved knowledge of the Pit Viper drills helped as well.

Jan 1, 2009

Geological Parameters Controlling the Improvement of Manufactured Sand Using Vertical Shaft Impact Crushers Instead of Cone Crushers Natural sand is a limited resource. In Sweden the total use of natural sand and gravel is around 20 million tonnes per year and the goal is to halve the use of this resource in the near future. Most of this natural sand is used for concrete production, so the consequence of this goal is that more and more concrete must be produced with manufactured sand. The bedrock of Sweden consists mainly of granites and gneisses, rock types mainly composed of various amounts of quartz, feldspar and mica. Manufactured sand from these materials generally contains rather flaky and elongated grains, and there are few types of granite that can be used as manufactured sand in concrete without increasing the amount of cement by eight to ten per cent. A Vertical Shaft Impact crusher (VSI) is commonly used to improve the shape of coarse aggregate particles. Research has shown that it is even possible to improve the shape in aggregate fractions less than 1 mm for some rock types. The aim of this project was to investigate which geological parameters control the improvement of manufactured sand when using VSI-crushers instead of the traditionally used cone crusher. In order to do this eight rock types of granitic composition were investigated. The selection of rock materials for the tests was based on grain size and mica content. A 4 - 8 mm fraction of each material was used for the tests. The characterisation of the shape of the material was performed using image analysis applied on microscopic images. The results showed that the VSI-crusher had improved the shape of all materials down to 0.036 mm, except for one rock sample. According to these results granites with low mica content and relatively high content of feldspars have the best prerequisites to produce manufactured sand for concrete with suitable geometric characteristics, and if these materials are crushed with a VSI crusher they almost show the same characteristics as natural sand.

Sep 13, 2010

By K. Schrijver, G. Beaudoin

"Four occurrences of galena-cemented sandstones, exposed in the Lower St. Lawrence - Gaspésie area, are described. They constitute a new, insufficiently explored type of deposit in Quebec.One mineralized body, a minor occurrence, is hosted in Lower Devonian rocks deposited in an estuarine, intertidal river channel during a marine regression; major cements are dolomite and sulphides. Another occurrence, a drilled prospect, is hosted in Upper Silurian rocks deposited unconformably on Cambro Ordovician basement during a marine transgression. With galena and quartz as main cementing minerals, it is similar to some well-known, economic sandstone-lead deposits. A third and fourth, a drilled prospect and a minor occurrence, are hosted in Upper Cambrian rocks deposited on continental slopes. In both, sulphides mainly occupy a secondary porosity. The differences between the third and fourth occurrences are: (1) cementing translucent minerals (carbonates and barite in one; chlorite in the other); (2) chronology of final subsurface dissolution (prior and subsequent to sulphide precipitation, respectively); and (3) important fracture porosity only in the barite-bearing deposit.The diversity of the four occurrences, and the unequal geological knowledge of their respective features, prohibit the formulation of uniform guidelines for further exploration.IntroductionThe attention of the mineral exploration community is drawn to four occurrences of galena-cemented sandstones (Fig. 2A) in the Cambrian of the Taconian Orogen and in the Siluro-Devonian basin of the Lower St. Lawrence and Gaspésie area (Fig. 1). In view of the fact that sandstone-lead deposits (Bjerlykke and Sangster, 1981) are, or have been, mined in several countries (e.g . Laisvall in Sweden: see Rickard et al., 1979; Largentiere in France: see Foglierini et al., 1980), the mere presence of occurrences in Quebec indicates that the mineral potential of some parts of the Appalachians requires further evaluation.Exploration for the deposits considered here is essentially restricted to geological methods and drilJing (e.g . Mainguet Suares and Samama, 1969), since the response to geophysical methods is virtually nil, at least in the initial, surficial stage of an exploration program. As the particular disciplines of geology utilized in exploration depend a great deal on the geological setting of a mineral occurrence, the diversity of the Quebec deposits is of prime importance. Therefore, the four occurrences (Fig. I, Table 1) studied by the authors are herein briefly described with emphasis on their stratigraphic and tectonic setting, and on the evolution of pore space and sequential occlusion of pores and fractures. Prior to further research in and around the occurrences, now in progress (e.g. Beaudoin, 1987; Beaudoin et al., 1987), it is hoped that the following outline will be useful to the explorationist."

Jan 1, 1987

By Napisporn Memongkol

Syntheses of Al-TiC-Al2O3 and Al-SiC-Al2O3 composites were obtained in situ by carbothermal reduction of mixtures of Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders. The reductions were carried out in a horizontal tube furnace under flow of inert gas. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The synthesized products were mixtures of aluminum reinforce with titanium carbide and alumina and aluminum reinforce with silicon carbide and alumina. The effect of the reaction temperature (1000 o C ? 1200 o C) and condition of precursors on the Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders were investigated using XRD and SEM method. The synthesized products showed those composites with aluminum matrix and titanium carbide and alumina as reinforced phases and aluminum matrix and silicon carbide and alumina as a reinforced phase was formed.

Jan 1, 2006

By Kenneth M. Maas

The U.S. Bureau of Mines began a five-year study of the 7.0 million acre Ketchikan Mining District during 1990. This study is part of the Bureau's ongoing statewide mining district evaluation program. The study area was subdivided and then prioritized by mineral potential into work units. Bureau field work in 1990 focused on the southern portion of Prince of Wales Island and vicinity. Extensive mineral resources have been mined historically in the area and are presently being evaluated by private industry. Information in this report is based on an extensive literature search and Bureau field work. Over 150 mines, prospects, and mineral occurrences were visited in 1990; an aggregate of 1,300 rock, placer, and limestone samples were taken; and nearly 3 miles of underground workings were mapped. Many prospects, some untouched for more than 80 years, were mapped and sampled. High metal values at several prospects were confirmed by Bureau sampling. Reconnaissance sampling along logging roads on Southern Prince of Wales Island revealed mineralized areas not previously recorded. Follow-up work at many locations is planned for the 1991 season.

Jan 1, 2011

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Feb 24, 1997

By Laura Mottola

Process Design and Change Management for Successful Deployment of Technology in Mining Over the last 30 years Canada has been successful in developing but not deploying hardrockmining automation. Our opinion is that the current lack of R&D investment and implementation capacity places Canada at risk as a future global mining leader A white elephant A burdensome possession; creating more trouble than it is worth. White (albino) elephants were regarded as holy in ancient times in Thailand and other Asian countries. Keeping a white elephant was a very expensive undertaking, since the owner had to provide the elephant with special food and provide access for people who wanted to worship it. If a Thai King became dissatisfied with a subordinate, he would give him a white elephant. The gift would, in most cases, ruin the recipient.

May 1, 2010

By G. G. Goble

Significant progress has been made in the past decade in determining the load bearing capacity of pile foundations. Developments in the means of prediction of pile capacity as limited by soil strength have been substantial, particularly in the use of dynamic methods. The use of currently available equipment, analytical procedures, and practices in the field, will often produce material economies on a job by allowing increased loads with proven factors of safety. This approach justifies the minimum number of piles required for a safe foundation in a wide range of job sizes and soil conditions. To avoid exposing the reader to excessive detail in the body of this paper, technical topics have been covered more thoroughly in several appendices. I. Wave Equation Analysis of Piles Appendix A II. Dynamic Monitoring and the Pile Driving Analyzer Appendix B III. Case Method Capacity Calculation Appendix C IV. Case Pile Wave Analysis Program Appendix D 1 Preliminary Analysis In designing driven pile foundations, there must be a close relationship between design, construction control procedures, driving practices, and the size of the job. Small commercial buildings or residences involving loads that are only a fraction of the pile capacities do not justify the expense of detailed design processes or elaborate construction controls. Nevertheless, some preliminary analysis of the job requirements and a limited subsurface investigation must be made to understand existing conditions and the possible foundation solutions. In other words, it is necessary to determine that driven piling is the best overall choice of foundation.

Jan 1, 1988

By A. C. Fieldner

ONE of the important functions of the Bureau of Mines is the, analysis of coal from every coal-mining State and Alaska. These analyses are being published for use of Government officials and the public. In connection with analytical data showing composition and quality of coals of the States, consumers, Producers, and the general public will be interested in a brief description of the geologic structure of the coal basins, typical mining conditions in the several districts, and the principal economic data of the industry. These publications have therefore heel) designed to include such features to present concisely the principal facts regarding occurrence, reserves, duality, characteristics, production, and uses of coals of each producing State.

Jan 1, 1952

By A R. Bye

Energy comes at great cost to our world and societies and therefore we should use it wisely and optimally. Societal pressure is enforcing this and the industry must respond by being proactive.The mine-to-mill approach to integrated mine and semi-autogenous grinding (SAG) mill optimisation demonstrated that throughput gains of up to 20 per cent could be obtained through a closer match of blasted run-of-mine ore to the feed best treated by a SAG mill. Since that approach was developed, new drivers have risen to prominence including environmental costs and impact of energy, water, waste. This is set against a backdrop of reducing ore grade and increasing demand that is pushing up our impact on the environment. The new challenges demand new approaches.This paper explores the opportunities in taking traditional approaches to optimisation to new levels of two-way integration and incorporating potentials for ore upgrade into circuit design. The new mantra may be æflexible circuitsÆ û designing and building for the present and the future by allowing for the uptake of new and future technology.

Jan 1, 2009

Coals from the Southern Coalfield of New South Wales treated in the Port Kembla coal preparation plants of Australian Iron and Steel Pty. Ltd. differ supstantially in their characteristics. Knpwledge of performance not only enables comparison and promotes better control, but also provides the means for predicting results.Evaluation of performance of cleaning equipment has been made in terms of probable error (Ep). Results for Baum jigs, a Chance cone, heavy medium cyclones, and water washing cyclones were examined. The efficiency factors derived from the probable error were applied to the float and sink analysis, mathematically simulating operating conditions. This method was applied to the Balgownie seam.The Balgownie seam lies between the Bulli and Wongawilli seams in the coal measures of the South Coast and mining on a large scale began recently in the Bulli area. It is known locally as the Four Foot seam and exhibits rather difficult washability characteristics, due to a comparatively high middlings content. These properties and the relatively high inherent ash make careful selection of cleaning equipment essential for optimum recovery. The prediction technique is used to determine the possible results when this coal is cleaned in the Port Kembla plants. Predicted values are compared with results from full scale trial washings demonstrating the validity and accuracy of the technique.Applications of result forecasting are listed.

Jan 1, 1971

By Lloyd Rowson

??Several factors have led to a review and reoptimization of the Midwest uranium deposit by AREVA Resources Canada Inc., the project operator, on behalf of the owners ??The current proposal is to mine the deposit using open pit methods and then transport the ore by truck on a dedicated road linking the Midwest site with AREVA?s McClean Lake Operation (JEB mill) for processing ??A decision has been made to begin mining the deposit by 2010 (pending regulatory approvals)

May 1, 2008

Simulation and Analysis of Media Behaviour in the Tower Mill by Discrete Element Method for Estimating the Power Draw and Spatial Distribution of Grinding Process The trends to the Tower Mill (TM) for grinding the materials are increased recently due to its unique merits. Among the various considerations of this machine, the main important items are increasing the efficiency of grinding as more as possible while keep the power consumption, manufacturing and maintenance costs as less as possible. Because this grinding process includes a huge numbers of media particles (ball or other shapes) that are interacted with each other and body of the machine, the DEM (Discrete Element Method) way is a very useful and essential step to getting confident evaluations. Because the DEM simulation is a very young scientific field and proper commercial software are very rare and still under modification, at first step, a FORTRAN code is developed for DEM simulation of two laboratory Tower Mill models (KM5 and KD5). The simulation and experimental results matched each other properly. Then one another DEM software was implemented to perform simulation of bigger models (huge numbers of balls), meanwhile could handle the complex 3D geometry data. The simulation and experimental results were compared and analysed in detail for not only laboratory but also for industrial models (KW5, KWD5, KWD50, KW300F, KW700F and KW1500) without any manipulation or compromising of the parameters of simulation. Some numeric data of industrial models are hidden here due to confidential reasons. The relative velocity of balls (ball-ball and ball-TM body), dissipate energy, interacted forces and stresses during the process are the key outputs of DEM simulation for design this machine. Therefore the main important processes in a Tower Mill machine are recognised and consequently some horizons of development of this machine are distinguished.

Sep 13, 2010

The reactions between molten aluminium and cryoIite have been determined from a material balance of all components involved in the process. The interpretation of results were supported by x-ray diffraction studies of the evolved vapours, quenched electrolyte samples, and side-reaction products.The most important reaction involves the formation of both Na2F (sodium subfluoride) and chiolite in the fused electrolyte. The Na2F accelerates vaporization of the melt. Some AIF (aluminium monofluoride) may also be formed but the proportion of this is much less than for the former subvalent compound.

Jan 1, 1968

By D. N. Dietz

Jan 1, 1969

By G. L. Mowrey, S. D. Maksimovic

An important element of the U.S. Bureau of Mines (USBM) mining research program is the development and evaluation of reliable coal interface detection (CID) systems. Commercially available CID sensors based on natural gamma radiation (NGR) are only applicable if the immediate roof is composed of shaley material. The USBM has made numerous underground and laboratory measurements using several NGR systems approved for installation on mining machines by the Mine Safety and Health Administration. In addition, two small handheld NGR instruments were used to make comparative measurements. Underground NGR measurements in 10 different coal seams, potassium-uranium-thorium radiometric analyses on samples from 16 seams, and chemical analyses of coal and rock for correlation with NGR counts were made. Laboratory test results on the effect of air gap and sample thickness, size, and weight on the NGR measurements, as well as general results of the various NGR systems, are discussed.

Jan 1, 1995

By N. S. Yet

This paper shall present the design and construction of bored pile and diaphragm wall for the proposed MHA complex in Singapore. The work was carried out by L&M Foundation Specialist Pte Ltd and PWD Consultants Pte Ltd was the consultant for this project. A brief description of the project is first presented to illustrate the scope and scale of the work involved, which includes the construction of bored piles and diaphragm walls and installation of steel stanchions in the bored piles. This is followed by a description of the methodology used to analyse and design the wall and bored piles. As both towers in this project are supported on bored piled foundation and are constructed by top down construction method, the analysis of the wall has taken into consideration the sequence of work phase by phase and this was carried out by means of a commercial finite element program called CRISP. Modelling of the problem will be briefly described and the findings from the numerical analysis will be presented. This is followed by a description of the structural and geotechnical design aspects of bored piles. The paper shall then describe the difficulties encountered for this project and solution used to solve the problem. The subsoil condition will be described with special mention on the encounter of very strong granitic rock at depth above the maximum excavation level of the basement at certain locations, hence necessitating the drilling of rock for a considerable depth for both bored piles and diaphragm wall. At this juncture, the construction method used to drill through the rock will be briefly described. For construction of bored piles, penetration of rock was carried out by chiselling or drilling using reverse circulation rigs. For construction of diaphragm wall, it requires the employment of Bauer hard rock cutter which uses cutting wheels fitted with roller bits and are capable of excavating into granitic rock of compressive strengths more than 100 MPa.

Jan 1, 2000

By Alan B. Wagner

Data from seven instrumented pile load tests in Milwaukee, Wisconsin and two other instrumented load tests reported in the literature, one in Evanston, Illinois and one in Houston, Texas were reviewed. The data were for pipe piles having diameters from 9-5/8 inches to 18 inches, driven to depths between 36 and 96 feet. These data were used to develop a relationship between effective vertical stress and unit side friction and unit end bearing. These relationships were based on readily measured soil parameters, undrained shear strength, Cu, and Standard Penetration Test (SPT) values. This Beta (ß) and Nt approach and four other methods were then used to calculate the bearing capacity of the nine cases analyzed. The results from each of the methods are compared with the measured results.

Jan 1, 1991

By Philip Bonanno

The first major project in Boston's new access to Logan Airport was an Immersed Tube Tunnel which extended 3,600 ft. from South Boston to East Boston across Boston Harbor. Twelve tube sections, 300 ft. long x 80 ft. wide x 40 ft. high, were lowered into an excavated trench which was then backfilled. The depth of the trench at mid-channel was approximately 100 ft. below mean high tide. At the East Boston end the tube terminated close to the present shoreline. At the South Boston end the tube terminated approximately 600 ft. inland from the shore line where a ventilation building was required. The depth to subgrade from existing ground at the ventilation structure was approximately 85 ft. The soil profile at this location consisted of 50 ft. of miscellaneous rubble fill, 25 ft. of Boston blue clay, and 10 ft. of glacial till. A small amount of weathered argellite existed at the north end of the structure. Part of the Morrison Knudsen, Interbeton, J.F. White, Joint Venture contract to construct the Immersed Tube Tunnel (ITT) was the construction of a cofferdam at the tube/ventilation building interface. The ventilation building was to be built as part of another contract. The construction of the cofferdam and the excavation to the building subgrade was the responsibility of J.F. White Contracting Company.

Jan 1, 1994