Search Documents

By R. L. Andrew

The southwest Pacific has produced at least four of the world’s premier porphyry copper-gold deposits, and the current level of exploration is likely to produce even more. An appreciable amount of gold is being produced with this copper, with obvious economic advantages. Gold content, in addition to their large size, makes the southwest Pacific’s porphyrycopper-gold deposits very attractive exploration targets. The recognition of telescoping and overprinting of porphyry systems has produced a greater awareness of the likely surface expressions, in particular the significance of advanced argillic lithocaps in porphyry exploration. The recognition of the spatial and genetic association of porphyry copper and epithermal gold systems (Sillitoe, 1972), as in other parts of the world, has had important implications for exploration in the Asia Pacific region.

Jan 1, 1995

By K. L. Morton

Groundwater and associated pore pressure represent elements that can have a negative impact on surface mining and slope stability. Groundwater flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely, if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data were available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By A. J. Kraemer

This paper is the second and concluding report of the results of the twenty-fourth semiannual survey made by the Bureau of Mines of motor gasoline marketed in the United states. The first report on this 1931 survey gave the results of the examination of the gasoline samples in accordance with the new Federal specification for United States Government Motor Gasoline. The present paper reports results of the examination of the gasolines for color, doctor test gravity, end point, per cent recovered copper-dish gum, and steam-oven gum. The retail price and the tax at the time each sample was taken are also reported.

Jan 1, 1932

By Xu Youzai

Static loading teets of five nodular piles and four non-nodular piles were performed in Tianjin soft clayey soil in which measurements of axial force and movements were made. Distribution of shaft resistance and load-movment curves for pile head and pile toe are presented in this paper. The applicability of nodular piles to soft soil and their effectiveness are also discussed. Based on the comparison, it is concluded that nodular piles have an advantage over non-nodular piles mainly in contri­bution to shaft resistance. Dynamic testing was also conducted through R. P. T. for evaluating the service load of tested piles.

Jan 1, 1991

By P K. Smith, R J. Ryan, W R. H Ramsay, D C. Arne, F P. Bierlein

Turbidite-hosted, mesothermal lode gold deposits in Paleozoic metasedimentary rocks of the Buller Terrane, western South Island have a similar geological history and genesis to the Paleozoic lode gold deposits ofVictoria, Australia and Nova Scotia, Canada. In all three regions the gold deposits are hosted by interbedded meta-sandstone and meta-argillite that have been folded and regionally metamorphosed to greenschist facies, and locally in Nova Scotia to amphibolite facies. The gold deposits are typically narrow, structurally controlled quartz veins associated with dilatant zones in reverse faults or fold-related fractures. The principal vein types include: bedding parallel or concordant veins, discordant veins, saddle reefs, and stockwork veins. En-echelon and "ac" type veins are sometimes also gold-bearing in Nova Scotia. The contrasting competency of the host meta-argillite and meta-sandstone beds is an important factor in vein formation, particularly for the bedding parallel veins, which are typically developed within meta-argillite beds or along the contacts between meta-argillite and meta-sandstone. Veins found within meta-sandstone units are generally discordant. The deposits in Victoria are well known for their bedding-parallel veins, saddle reefs ( Bendigo ) and leather jacket reefs (Ballarat). Bedding-parallel veins are also common in Nova Scotia , along with a few examples of saddle reefs. In contrast, vein formation probably occurred later in the deformation history of the Reefton and Lyell goldfields, with most veins being bedding discordant and more typically aligned with the axial plane cleavage of the folds rather than bedding planes. The quartz lodes in one deposit, Globe-Progress, strike approximately perpendicular to the bedding and fold axes. No saddle reefs have been recorded from the Buller Terrane. Mesothermal vein morphology reflects the amount of fmite strain, the strain rate, competency contrasts, lithotypes, and the confirming pressures to which the system was exposed. On the basis of comparable depositional depths and rheologies of the host rocks, a controlling factor influencing the development of different vein styles (and timing) might be finite strain, as exemplified by the tightness of folding in the host rocks. Folding appears to be tighter in the Victorian rocks than in either the Buller Terrane or Nova Scotian rocks.

Jan 1, 1999

By J Kelly, C Kelsey

The Autogenous Kelsey Axial Displacement (KAD) mill is essentially a short retention time centrifugal mill, designed to effectively harness extraordinarily high concentrations of input energy for efficient particle size reduction. The mill which has an operating duty band extending from primary to ultra-fine also has the unique capacity to generate fine and ultra-fine products from single stage size reductions of either coarse or fine mineral feeds, in both wet or dry operating modes. This paper covers developments following a recent optimisation programme which confirmed that mill shell speed and the velocity differential between the shell and the rotating internal disc assembly tips could be optimised in relation to specific energy for a given feed rate and feed size providing the product size remains constant. Subsequent test-work further demonstrated the versatility of the mill with duties ranging from the removal of surface contamination associated with heavy mineral concentrate particles to the production of premium ultra-fine talc, from a single stage of size reduction. Open circuit grinding of a rougher gravity concentrate to liberate gold ahead of leaching also highlighted the scope for the application of low cost KAD milling for a range of hydrometallurgical feed preparation duties, which involve fine and ultra-fine grinding.CITATION:Kelly, J and Kelsey, C, 2013. Advanced media-free fine and ultra-fine grinding - The Kelsey axial displacement mill, in Proceedings MetPlant 2013 , pp 152-161 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By E A. Amaral Jr, A C. Chieregati, J C. O Souza

Cross-belt samplers are designed to sample particulate material in processing plants, usually when there is no space to install a conventional linear falling stream sampler. Most of the available cross-belt samplers are mounted on the top of conveyor belts, and remove each increment from a loaded moving conveyor with a 360° rotation of an open faced cutter, in a plane perpendicular to the material flow. Despite the practicality of this equipment and the fact that it occupies very little space in the plant, cross-belt samplers are well known for collecting biased samples, especially due to the increment extraction error. Sampling consultants around the world tend to condemn this sampling equipment, claiming that it is incapable of collecting the fine material from the bottom part of the load, and, since the sampling probability is not uniform for all fragments and depends on its position in the stream, this kind of sampler generates biased samples and its use should be avoided. Furthermore, the greater the segregation effect between particles, the larger the bias. However, some plants, whose initial design did not plan for the installation of a falling stream sampler, must rely on cross-belt samples for process control and reconciliation. For the past years, sampling equipment manufacturers have been putting effort in modifying the cross-belt sampler design in order to comply with the principles of correct sampling. Changes to the cutter material, shape, position, speed and movement in relation to the material flow have been made, and are continually being tested for different types of ore with various chemical and physical characteristics. This paper presents the improvements made to a cross-belt sampler at a gold plant feed in Brazil and describes the tests performed until it was possible to validate the new sampling equipment for reconciliation purposes.CITATION:Chieregati, A C, Amaral Jr, E A and Souza, J C O, 2017. Validation of a modified cross-belt sampler for reconciliation purposes, in Proceedings Eighth World Conference on Sampling and Blending , pp 247–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By C. A. Geffen

This report, sponsored by the U. S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the com¬ponent operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By R J. Goldfarb

Reduced intrusion-related gold deposits have become a new, low-grade, large-tonnage exploration target during the last decade. The best recognized examples of such deposits are recognized throughout the Tintina Gold Province of the northern North American Cordillera. Because such examples may have many features in common with orogenic gold deposits, such as anomalous Bi, W and Te, low salinity and CO2-rich ore fluids, and a spatial/temporal association with igneous rocks, confusion and controversy have now become commonplace in classification of many gold deposits formed along convergent margins. The best discriminators of IRGS are likely to be their: +        regional location in deformed shelf sequences on the inboard side of a series of accreted terranes and within terranes that also contain important tin and (or) tungsten deposits; +        local spatial association of gold ores with cupolas and contact aureoles of relatively reduced, alkaline-leaning, and volatile-rich plutons; +        post-deformational timing of gold deposition; +        extremely low sulfide content (commonly <1 vol %) of ores within igneous bodies and the outward zoning, through proximal skarns and to distal base metal-rich veins, from the causative pluton; and +        low grades (<1 g/t Au) of auriferous sheeted vein systems in pluton cupolas.

Jan 1, 2005

By R. Cotton

"1. INTRODUCTIONTo say that the environment will be a dominant issue in the 1990' s is an understatement. A world-wide ""green revolution"" is taking place not only with the general public and politicians, but in the boardrooms and plant facilities of corporations around the world. There is probably not a plant manager who has not been requested by his corporation to assist in some way on environmental issues by providing advice and strategy, by dealing with customer or community concerns, by considering environmental matters in transactions, by developing new environmental compliance policies and requirements, and so on.There are, in the author's view, three main challenges for the mining industry in the environmental area in the 1990's. This paper will discuss each in turn. The first challenge is the concept of ""sustainable development"". Whatever the meaning of this much-debated phrase, we are rapidly moving beyond the buzzword, and into the specifics. It will clearly impact on the way we manage our companies, our communities and our personal lives.The second is the challenge of personal liability; particularly for officers, directors, supervisors and managers of the corporation. For example, in Ontario today, a good percentage of prosecutions for pollution offences are against individuals, usually managers and supervisors, in addition to the prosecutions against the corporation itself for the same offence. In all likelihood, prosecutions will increase in number and will increasingly be directed at individuals. A corporate president has already served a jail term for contempt of court related to his corporation's breach of a court order related to sewer by-law offences. Although the case is on appeal, another president has become the first officer in Canada to be sentenced to jail for violation of an environmental protection statute. Other corporate officers and directors have recently been charged with breach of their duty under Ontario's Environmental Protection Act."

Jan 1, 1991

By Ernie Doell, Trung Nguyen

"In early 1995 Cluff Mining commissioned a newly constructed high density tailings thickener at its Cluff Lake uranium mill. The 85 ft diameter high density thickener is one of the first of its kind in North America, and incorporates the novel paste technology in its design to produce densified (in the range of 60 -65% solids) mill tailings suitable for stable deposition in the tailings management area. This paper discusses the impetus behind the installation of such an unconventional thickener, and the many trying experiences in making it operational.IntroductionCluff Mining, a wholly owned subsidiary of Cogema Resources Inc., is the operator of a uranium mine and mill complex at Cluff Lake which is located in northern Saskatchewan. Since 1980, the company has developed and mined out several different ore bodies within the Cluff Lake region for the production of uranium concentrates, commonly known as yellow cake. Based on the known ore reserves, the Cluff Lake operations are projected to last till the early 2000's.Tailings from the Cluff Lake mill have been discharged to a tailings management area consisting of a tailings pond and two facilities for primary and secondary treatment systems. The tailings pond has an impervious bentonite lined dam, and it is divided into a solids and a liquids holding areas. Until the beginning of 1995, the mill tailings were discharged in two separate lines to the solids pond; one line carried the slurry residue of 45-50% solids (w/w) from the CCD circuit, and the other discharged raffinate tails containing less than 1 % (w/w) gypsum precipitate. Supernatant in the solids pond is treated in the primary treatment system prior to discharging to the liquids pond. Figure 1 shows the site plan of Cluff Lake tailings management area.It has been estimated that by the end of 1995 the solids pond would be filled to about 60% of its design capacity, and probably would be full before the year 2000. Therefore, Cluff Mining had to consider a more efficient tailings disposal method that could extend the service life of the existing Cluff Lake tailings management area. A high density tailings thickener was believed to be the most practical and economical system for tailings disposal at Cluff Lake mine."

Jan 1, 1996

By John H. Wright

The United States Antarctic Program (USAP), through its principal support contractor Raytheon Polar Services Co. (RPSC), has recently completed a three-year project comprising nearly 936 m (3,071 ft) of undersnow utility tunnels at Amundsen-Scott Station, South Pole, Antarctica. The tunnel serves the new station facilities that are currently under construction. It houses the piping that conveys fresh water from current and future water well sites, as well as waste water to repositories in abandoned wells. The undersnow tunnels permit year-round access for system operations and maintenance. The network of tunnels is entirely unlined and unsupported. And, for the most part, it maintains a rectangular cross section of 1.8-m-wide x 3-m-high (6 x 10 ft).The tunnel runs from 6 to 14 m (18 to 45 ft) below the surface. Eight 1-m- (3.3-ft-) diam raises bored from the surface serve the network as emergency escapeways.

Jan 1, 2002

By R. R. Falier, W. E. Rice

"PURPOSE OF REPORTThis paper presents the results of a series of tests made by the U. S. Bureau of Mines in cooperation with The Ohio State University Engineering Experiment Station as part of an investigation on the use of fuel in kilns.This report is preliminary and gives only enough of the test data to illustrate results and show the reasons for the successes and failures of the method of firing investigated; fuller details will be included in the final report.PERSONNEL FOR TESTSThe investigation is conducted under supervision of P. Nicholls, supervising fuel engineer, of the United States Bureau of Mines, and G. A. Bole, research professor, of The Ohio State University. These tests were made under direction of W. E. Rice, associate fuel engineer, assisted by R. R. Faller, assistant fuel engineer, of the United States Bureau of Mines; H. C. Harrison, senior research engineer (until October 1, 1930), C. R. Austin, senior research engineer (since October 1, 1930), and H. K. Van Sohoick, junior research engineer, of The Ohio State University. M. J. Rice, field engineer, represented the manufacturer of the stoker.PURPOSE OF INVESTIGATIONThe general aim of the investigation is to develop more economical methods of using fuel in kilns and to improve the over—all efficiency of the process of firing by methods that will produce ware of better quality. One phase of this investigation is the burning of coal on an automatic stoker to gain the advantages of control, constant rate of application of heat, and ability to burn cheaper coal than can be used in the hand—fired furnaces of kilns. It a stoker in to be used it is desirable that the coot of the installation should be low, the control of operation simple, and the distribution of heat in the kiln as good or better than with hand firing. These desiderata were sought in the stoker and furnaces that were used for the tests described herein. The tests were made to determine whether it is feasible to fire a large kiln with a single stoker, whether the use of a single furnace simplifies control, and whether the admission of all the hot gam at the center of the kiln will give symmetrical distribution of heat."

Aug 1, 1931

By C. W. Siyasiya, K. A. Annan, W. E. Stumpf

"SynopsisThe relationship between niobium content and austenite grain growth has been investigated through hot rolling simulation on a Bähr dilatometer. The effect of delay time between passes during rough rolling in Nbmicroalloyed steels with nitrogen contents typical for electric arc furnace (EAF) melting was studied. The results indicate that the grain growth constants n, Q, and A increase with an increase in Nb content. The activation energy for austenite grain growth Q was found to be in the range of 239 to 572 kJ/mol, the exponential constant n ranged from 2.8 to 6.2, and the material and processing condition constant A from 4.24 × 1012 to 4.96 × 1028, for steels with niobium contents ranging from 0.002% Nb to 0.1% Nb. A general constitutive equation for the prediction of austenite grain growth in these Nb-microalloyed steels under rough rolling conditions has been developed. Good agreement between the experimental and the predicted values was achieved with this constitutive equation.IntroductionGrain refinement has been found to increase both the strength and toughness of steels (Gao and Baker, 1998; Sharma, Lakshmanan, and Kirkaldy, 1984; Seok et al., 2014; Maalekian et al., 2012). It is also known that the austenite grain size directly influences the microstructure, and thus the mechanical properties, of the steel (Maalekian et al., 2012; Yue et al., 2010). Effective grain growth control is reported to be achieved through addition of precipitate-forming elements, such as Nb that, slow down the grain boundary migration through pinning and solute drag mechanisms (Yu et al., 2010; Olasolo et al., 2011; Alogab et al., 2007). Much work has been carried out on austenite grain lsize control by the addition of precipitate-forming elements that have a strong affinity for interstitial elements, such as carbon and nitrogen, which form the dispersed pinning particles to inhibit the austenite grain growth (Alogab et al. 2007; Hodgson and Gibbs, 1992; Nanba et al., 2003; Flores and Martinez, 1997; Rollett, Srolovitz and Anderson, 1989). Austenite grain growth can be described using a conventional or a modelling approach. With conventional approaches (e.g. metallography), in-situ monitoring of austenite grain growth at high temperatures is impossible. Modelling the grain growth behaviour based on available data is the ideal option. To quantitatively describe austenite grain growth therefore requires development of a sound mathematical austenite grain growth equation that accounts for the effects of the varying microalloying elements in inhibiting austenite grain growth. Numerous attempts have been made to develop an empirical model based on the general equation developed by Sellars and Whiteman (1979). Many of these models do not account for the direct effects of the microalloying elements such as Nb in austenite grain growth control [Fu et al., 2011; Wang and Wang, 2008; Wang et al., 2006; Shanmugama et al., 2005; Banerjee et al., 2010; Pous-Romeroa et al., 2013). The current work has considered this limitation, taking into account the direct effect of niobium in grain growth control during thermal processing. This is done by incorporating the initial austenite grain size Do and the microalloying element niobium in the development of a constitutive equation for grain growth prediction in Nb-containing microalloyed steels."

Jan 1, 2015

By Xinli Wang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng, Byoung-Gon Kim

"The microwave reflection loss (RL) of ferric oxide is studied in the temperature range from 297 to approximately 1400 Kat frequencies of 915 and 2450 MHz. It is shown that the maximum microwave absorption with RL of -38.46 and -35.97 dB can be obtained for ferric oxide having thicknesses of 0.03 and 0.01 m at 915 and 2450 MHz, respectively. The maximum absorption peak with RL below -10 dB is in a 250 K temperature range from 723 to 973 Kat 915 MHz, which shifts to the range between 823 and 1073 K at 2450 MHz. This migration is in good agreement with the variation of the dielectric loss tangent of ferric oxide.IntroductionMicrowave irradiation has distinguishing characteristics such as volumetric and selective heating compared with conventional methods, leading to extremely broad applications in materials heating and processing [1-5].The efficiency of microwave heating was found to be dependent on various factors, such as microwave power [6], frequency [7,8], radiation time [8], applicator geometry [8], sample microwave absorption properties and position as well as dimension [9-11 ], etc. Among these parameters, sample dimension plays an important role but is usually neglected by researchers in microwave processing of materials. In fact, although numerous studies have been directed toward the utilization of microwave energy to assist materials heating and processing, few reports were released on the effect of sample dimension [12,13].This is because all aforementioned factors influencing microwave heating generally exert interactive effects to each other during the heating process, making clarification of the effect of sample dimension difficult. Therefore, it is necessary to propose a parameter or concept for quantifying the effect of absorber dimension on microwave heating, increasing heating efficiency."

Jan 1, 2013

By N. Malakondaiah

Several growth chamber and laboratory experiments were conducted to study the germination behavior of plant species on mine spoils and plant growth responses to nutrients on spoils and topsoils. Experiments were conducted to study the germination potential of some native and introduced species under various conditions. The seeds of green needlegrass, side oats grama, thickspike wheatgrass, crested wheatgrass, birdsfoot trefoil and emerald crownvetch were less tolerant, whereas those of alkali sacaton. durar hard fescue, slender wheatgrass, yellow sweetclover and alfalfa were most tolerant to the sodic mine spoil conditions. Addition of leonardite improved the germination potential of some of the poor genninators. Slender wheatgrass and yellow sweetclover were used as test plants to study the fertility status and productivity potential of stockpiled topsoils and spoils collected from Center. Glenharold and South Beulah of North Dakota. The topsoils were neither saline nor sodic but low in N and P. The spoils were neutral to alkaline with SAIL of 12-32, EC of 1.8-5.5 mmhos/cm, Olsen&apos;s P< µ4g/g, and total N <0.07%. Application of N and P together to the topsoils increased the yield of wheatgrass and sweetclover by 88% and 70% of their respective maximum yields, whereas near maximum yields were obtained for both the species by the same treatments to the spoils. The average yields on topsoils were higher than the yields on spoils. The concentrations of major nutrients were higher in plants grown on topsoil, whereas the opposite was true with the concentrations of Mn, Zn, and Cu. Growth chamber experiments were also conducted to study the growth responses of alfalfa, oats and slender wheat grass by the application of Mn and Zn to a sodic coal mine spoil which was previously used for pot culture experiments. Significant growth responses to Mn and Zn were observed in alfalfa but not in oats or slender wheatgrass. Fertilizing the spoil with Mn along with NPK increased the yield of alfalfa to 85% and with Mn + Zn to 99%. Growth responses and plant composition results of this study confirm that the application of major nutrients to spoils can accentuate Zn and Mn deficiencies in some plants.

Jan 1, 1982

By Yael Miron

This report describes laboratory studies by the U.S. Bureau of Mines to determine the suitability of a static oxygen (OJ adsorption test for evaluating the self-heating tendencies of coals. Reliable minimum self-heating temperature (SHT) values from adiabatic oven tests were used as standards for comparison and evaluation. A suite of six coals was tested in the adiabatic oven and in sealed flasks. In the latter tests, both undried and dried samples, in a range of four particle sizes, were examined. Miniature pressure trans-ducers monitored pressures in the flasks, and gas samples taken at the end of the tests quantified all the gases present. An excellent correlation was found between the minimum SHT&apos;s and amounts of O2 adsorbed over a 7-day period for dried coals, independent of particle size. In addition, a good correlation was obtained between the minimum SHT&apos;s and pressure changes in the flasks at the end of the test for the same coals, also independent of particle size. Based on these results, the sealed flask test can be reliably used to determine the self-heating tendency of a bituminous coal sample.

Jan 1, 1990

By E. C. Morton

The Western Australian School of Mines (WASM) has developed a facility for the static testing of large scale ground support elements. The samples are loaded using a mechanical screw feed jack. Instruments measure the displacement and the load being applied. Methods have been developed for testing of mesh, shotcrete and membranes. Mesh samples are restrained on all sides and loaded centrally. A new large scale punch test method has been developed to evaluate shotcrete and membranes. These products are sprayed on to a sandstone substrate containing a centrally located isolated disc. The sprayed product is loaded by displacing the disk. The different test methods are described in detail. The test program involved two types of mesh, several shotcrete mix designs with different curing times and one membrane product. The force-displacement responses are used to directly compare the products. The implications for implementation of the different ground support products are discussed.

May 1, 2009

By Rómulo Mucho Mamani

El presente trabajo señala el uso de la tecnología existente en INGEMMET para el servicio de los operadores mineros de pequeña escala, orientados fundamentalmente a la explotación del oro. En este sentido, el uso del conocimiento y de los instrumentos informáticos son elementos que facilitan la difusión de la información geológica para este fin, los mismos que al ser interpretados en laboratorio y contrastadas en el campo, ofrecen resultados de relevante utilidad para la toma de decisiones y coadyuvan al proceso formalizador del subsector.

Sep 12, 2005

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.