Search Documents

By F. W. Bowdish

Analysis of data on the equilibrium exchange of sodium ions from salt solutions for calcium ions, from various fractions of an oxidized calcareous iron ore from Lorraine, France, strongly suggests that the calcium may be attached to the solid by only one of its bonds. Nearly equal values were found for the equilibrium expression from data covering concentration ranges of 1000 fold for the salt and 235 fold for the ion-exchangeable calcium. Differences indicated between the exchangeable calcium contents of the slime and the sandy portions of the ore, as well as the equilibrium relationship itself, are of importance in the flotation of the ore. During an experimental program on the flotation of oxidized calcareous iron ores from Lorraine, France, ion-exchangeable calcium was found in the ore. Because this source of calcium ions, if not controlled, could thwart all efforts at flotation, an extensive study was made of the phenomenon. The part of that study reported here was to obtain data on the equilibrium established between ore solids and solutions of sodium chloride, and to analyze the data to try to understand better the physical chemistry of the exchange. The ore contains oolites of goethite and quartz grains embedded in a matrix consisting of calcite and a brown cement believed to be the residue from oxidation of the silicate minerals found in fresh unoxidized ore. When ground, a substantial fraction of the ore becomes a fine slime in which is concentrated more than half of the alumina content of the ore. It is believed that the alumina occurs as unidentified clay minerals with which most of the ion-exchange capacity of the ore is associated. A preliminary experiment on the exchange of ions from the ore for sodium ions from solutions of NaCl showed that calcium was about ten times as abundant as magnesium in the exchange solutions. Thus calcium was the predominant ion in causing difficulties with flotation, and it was the only one for which data was obtained in this study. It is believed that the omission of magnesium ion exchange from consideration does not invalidate the results. It is possible, however, that inclusion of magnesium in the analyses and calculations or its prior elimination from the samples would have improved the consistency of the results. EXPERIMENTAL Data about the equilibrium exchange of sodium from solutions for calcium from the solids were obtained using two different samples of material. The solids

Jan 1, 1963

By M Kozikowski

The primary purpose of these investigations is to determine dewatering requirements and likely impacts associated with mining operations. Standard aquifer testing techniques were carried out at multiple locations within the Ord Range near Pardoo, Western Australia. Aquifer properties of an oxidised haematite orebody were calculated from test pumping data conducted in five fully penetrating test bores. Hydraulic properties of the Ridley magnetite orebody were calculated based on short term constant rate pumping tests, and packer tests. Packer tests were conducted in undeveloped and uncased exploration holes and diamond core holes. The new data sheds light on the hydrogeological properties of this previously unexplored region of Western Australia.Aquifer testing procedures for each bore included a preliminary step test followed by a constant rate test. Recovery data were collected in each bore over a period of four to six hours. Prior to testing, background water levels and water samples were collected in a network of monitoring and exploration bores to establish baseline water levels, gradients and water quality. Water quality within the bedrock of the Ord Range varies from 2000 to 5500 mg/L TDS whereas water quality within the alluvial sequence of the De Grey River is highly variable (400 to 2500 mg/L TDS), but is predominantly brackish with some water of potable quality which is used to supply Port Hedland. Test pumping supports the conceptual hydrogeological model that consists of a pod like orebody (aquifer) surrounded by low permeability waste rock (BIF), with very weak hydraulic connection to the adjacent alluvial systems. Calculated hydraulic conductivity from test pumping data across Pardoo ranged from 0.01 to 59 m/d, depending on deposit tested.A groundwater model was used to simulate dewatering required in proposed pits and to estimate the impact of dewatering on the surrounding shallow alluvial aquifers. Test pumping and numerical groundwater flow modelling indicate the proposed below water table pits can be successfully dewatered utilising in pit dewatering production bores. Yields from individual dewatering bores will reduce with time due to the reduction in saturated aquifer thickness.Based on the numerical groundwater modelling and field investigations the likely impacts to the adjacent De Grey River alluvial aquifer system (within the Priority 1 De Grey River Water Reserve) resulting from mining and dewatering activities is considered minimal. Recalibration of the groundwater model will be undertaken once several months of dewatering data are available.The aim of this paper is to present a range of aquifer parameters derived through standard aquifer testing techniques for an area previously unexplored in terms of hydrogeological characteristics. It is the goal of the authors to provide this comparison data set for future work in similar geologic media.

Jan 1, 2009

By F. D. Wright, H. D. Fara

The solution to the plastic and elastic stresses around a circular shaft in a hydrostatic stress field that has appeared in two editions of a widely used book on rock mechanics1 is in error. Although this is a relatively minor matter, the correct solution was not found by a literature survey, so it appears worthwhile to present it. For a homogeneous, isotropic, rigid plastic-elastic body in plane strain which obeys Tresca's yield criterion the following equations must be satisfied:'," In the plastic zone,

Jan 1, 1963

By Mohammad Nasim

Vertical expansion of existing structures frequently requires foundation retrofitting to enhance the capacity of existing foundations for supporting additional loads. Owing to their small diameter, a variety of suitable drilling methods available for installation, and smaller installation equipment capable of operating under limited headroom conditions, micropiles are often preferred for foundation retrofitting. This paper presents a case history demonstrating application of micropiles to underpin the existing foundation of the Washington D.C. Children?s National Medical Center (CNMC) for its future expansion. Located at 111 Michigan Avenue in northwest Washington, DC, portions of the hospital currently extend five stories above grade and three levels below-grade as parking garages. The hospital intends to expand the surgical wing up to the current build out (five stories) above the remaining portion of the existing parking garage. The original foundations consist of 80-ton Raymond Step-Tapered piles. New loading on the foundations required each Raymond pile to be capable of supporting 150 tons. Results from quick load tests on existing piles indicated that two entire column lines (Column Line A and B) would experience loads beyond their capacity, requiring enhancement of the existing foundation at these locations. The design and construction of the foundation upgrading work was particularly challenging due to various project constraints related to a high groundwater table, micropile installation under limited head room, and ensuring that the parking garage remained fully operational for the entire duration of construction. The paper presents the challenges faced during testing of existing foundations amid a high groundwater table, design developments of underpinning options to support the additional column loads, difficulties and challenges encountered during installation of the micropiles and construction of the micropile pilecaps, and value engineering options developed during various phases of the project. Understanding that micropiles are often a preferred option for foundation retrofitting, the case history is expected to provide a baseline design approach and innovative solutions to typical challenges faced during construction, thereby reducing potential cost overruns during design development and construction of similar future projects.

Jan 1, 2008

By Catherine Aimone-Martin, Mary-Alena Martell

Whole-structure and mid-wall responses of 33 non-traditional structures to surface coal mine blasting were characterized. Eighty-nine blasts were conducted at 11 mine sites throughout the U.S. to measure blastgenerated dynamic response of structures typically found in the proximity of surface coal mining. Structures selected for this study include log-type, manufactured (single- and double-wide trailers), “mine camp”-type, adobe, and stone. Traditional acoustic microphones, t&axial (ground) and single component (structure) velocity transducers were used to record airblast, ground motions, and structures response time histories with a common time base. Wall crack displacement gages were used to record static and dynamic movement of existing drywall cracks. The relative responses of selected “atypical” structures to blast vibrations and nonblasting causes of structural stress, including natural forces, environmental effects, and human habitation, are compared. The purpose of this study is to document and compare vibration characteristics of structures that were not included in previous studies conducted by the U.S. Bureau of Mines and others in establishing the widely adopted safe level blast vibration criteria in the U.S. An important objective of this study is to outline an evaluation process including structure uniqueness relative to cracking susceptibility.

Jan 1, 2002

By Mehrotra G. M, Frohberg M. G

Based on the concepts of statistical thermodynamics of athermal mixtures, an approach is developed which is capable of quantitatively explaining the thermodynamic properties of binary silicate systems. Expressions for the ionic fractions of various anionic linear and nonlinear chain polymers are derived. The developed expressions for free energy of mixing are tested by applying these to the system PbO-SiO2. The ionic fractions of various chain polymers in this system are calculated. The two cases, namely, of linear and nonlinear chain polymers are compared with each other.Limitations of earlier models are pointed out.

Jan 1, 1975

By Beardsmore G. R

Geothermal gradients in the Gippsland Basin commonly exceed 35¦ C/km. Consequently models of thermal maturation may indicate exploration targets with an anomalous age/depth distribution. However regional geothermal models are constrained primarily by observations of surface heat flow. High geothermal gradients may simply reflect the presence of low conductivity coal beds within the basin. Heat flow data are not readily available for the Gippsland Basin. Normally special purpose drill holes are required to provide direct determinations of surface heat flow. These provide core samples for thermal conductivity and allow measurements of a stable geothermal gradient at least one year after drilling. Different indirect procedures are now required to provide estimates for the Gippsland Basin. Bottom hole temperatures can be used with suitable corrections to provide an indication of the regional geothermal gradient. However the corresponding thermal conductivities are more difficult to determine. Geophysical logs can be used to detect the major lithologies but detailed statistical analysis is required for numerical estimates. Complex mixing models are now suggested for geothermal surveys linking physical properties to variations in the mineralogy of each well. Allowing for low conductivity coal measures the data in the Gippsland Basin suggest values for heat flow consistent with regional trends in Australia. Interpretation is complicated by overprinting of transient thermal events with different time scales. Apart from the tectonics of basin evolution geothermal signatures may be complicated by regional ground water migration, the 'hot spot' trace associated with southward younging of Cainozoic volcanism, diagenesis, and basin refraction.

Jan 1, 1992

By John L. Morning

Although faced with a slowdown in the world economy, continued inflation, and rising costs, the mining industry exceeded its 1974 raw mineral production value of $55.1 billion by 13%. The increase was due to value increases in the production of fuels and nonmetals; metals reported a decrease in value. Of 23 metals produced, 14 showed value increases; of 44 non-metals produced, 26 reported value in-creases. Because of increasing costs and depletion of high-grade reserves, the mining industry continued to rely on new technologies to maintain its profit margins. In the surface mining sector, the development of new tools and equipment played a large part in increasing production and maintaining this goal. Some of the types of equipment developed were instrumentation for control of pit slope stability, shovel power transmissions, electric wheel trucks, and single-flight conveyor systems.

Jan 1, 1977

By J. D. Stone

This paper briefly reviews the adequacy of existing management theories and practices and the managerial proficiency or competency in the South African mining industry. The investigation revealed that existing management practices are totally inadequate to enable all employees on all the levels of the mining industry to achieve the results required from them, in all aspects, at all times. As a result, the South African mining industry is gradually losing its long standing reputation as a relative cheap, competitive, and reliable supplier of minerals to the local and global markets. According to some prominent management authors and theorists, an all-inclusive unified management theory does not exist at present. In this paper the authors summarize the main aspects of a newly developed comprehensive, practical, and integrated management method. It is believed that the application of this method would significantly improve the future performance and competitiveness of the South African mining industry

Jan 1, 2010

By Stephen L. Chryssoulis, Daniela Venter, Stamen Dimov

"Comparative surface analysis of floated and rejected free gold grains from a number of full scale benefication plants and from pilot plant testwork, has shown silver (the most common impurity in gold) and sulphur invariably in greater concentration on floated gold grains, implying that they assisted gold flotation (gold activators). Collector loading measurements on individual gold grains from concentrates of staged rougher flotation tests on a cyclone U/F product of a pyritic gold ore, revealed first progressively lower concentrations of the collector monomer on gold from each follow-up concentrate and secondly a direct proportionality between the surface concentration of silver and the collector monomer. These two observations leave no doubt that silver activates gold and that collector monomers play a significant, previously not fully recognized role in gold flotation.INTRODUCTIONGold to some degree is naturally floatable in industrial systems, which means that it can be recovered without collector addition (Marsden and House, 1992). This is due to the adsorption of hydrocarbons and deposition of sulphur, which are dependent on the metallic properties of gold, particularly its high electrical conductivity, which allows surface electrochemical reactions to occur catalytically and selectively. Cyclic voltammetry has shown that gold can be rendered hydrophobic by deposition of a surface layer of sulphur (Sº) from S2- and HS- solutions (Walker et al., 1984). Twenty monolayers of sulphur were required to produce a hydrophobic gold surface.However, no sulphide flotation plant relies solely on the natural floatability of gold for its recovery. Gold hydrophobicity is enhanced by the addition of flotation collectors such as xanthates (X), dithiophosphates (DTP), dithiophosphinates (DTPI), mercaptobenzothiolates (MBC) etc., as used in sulphide mineral flotation (Dekok, 1973: Adams et al., 1986). The mechanism invoked in enhancing the hydrophobicity of pure gold with the aforementioned four groups of collectors is similar to that of pyrite, whereby collector anions are oxidized at the gold surface to form dimers (Groot, 1987; Marsden and House, 1992; Basilio et al., 1992) As an example, xanthate ions are oxidized at the gold surface to form the neutral dimer dixanthogen (X2):"

Jan 1, 2003

By Y. L. Sun

The feasibility of using the ultrasonic wave attenuation method for measuring in-situ stress is examined theoretically and experimentally. The theoretical analyses show that for a given rock type the relation between stress and attenuation coefficient ratio can be approximated closely by second-order polynomials. Combining the elastic and statistical theories, the magnitude and direction of the existing principal stresses can be predicted by using the relations between stress and attenuation coefficient ratio obtained in the calibration of core specimens. Several experiments are conducted in the laboratory on two types of rock. The experimental study consists of two parts: the attenuation-coefficient measurements in core specimens under uniaxial stress and the attenuation coefficient measurements in boreholes drilled through blocks of sandstone and limestone subjected to uniaxial compressional stress. Compressional waves are used exclusively in the measurements.

Jan 1, 1989

By Thomas W. Camm

This study was done to evaluate the costs of various dumping operations at waste and spoil piles. It has been theorized that accidents associated with dumping operations might be reduced by short-dumping rather than edge-dumping, but many operators have been reluctant to use short-dumping because they believe it is not as cost effective as edge-dumping. To evaluate this perception, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health reviewed the costs of various dumping methods at waste and spoil piles. The study found that overall cost differences between the two methods were not significant in most cases. However, while overall cost differences between the two methods appear small, capital costs could be more significant when short-dumping if numerous dump sites are used concurrently. The choice of which method to use should be based on considerations of the safety of dozer and truck operators.

Jan 1, 2000

According to the previous research, it is found that the thickness of cover is mostly less than 100 m for highwall mining system. However, for most of the Chinese surface coal mines, the mining depth is over 150 m; on the other hand, the shovel-truck is the most common mining technology. As a result, a lot of residual coal will be remained around end-walls. Considering these facts, the calculated methodology of highwall mining system under thick cover is presented in this paper. Meanwhile, numerical simulation of highwall mining system under thick cover was carried out. The outcome shows that the calculated methodology for pillar stability of highwall mining system under thick cover presented in this paper is acceptable. In other words, the highwall mining system is feasible to extract the residual coal around end-walls in Chinese surface coal mines. Thus, not only coal recovery ratio can be improved, but also can increase the production life of surface coal mines in China.

Jan 1, 2012

By Michael Valencia, Alonso Marchena, Fredy Arcos, Miguel Chumbe

Cobrepampa es un depósito de cobre ubicado en Acarí (Caravelí-Arequipa). La mineralización se emplaza en pórfidos dioríticos pertenecientes al intrusivo Cobrepampa (Superunidad Linga) y está constituida por bornita, calcosina, covelina y calcopirita y en la zona de oxidación cuprita, crisocola, malaquita y hematita. El magmatismo es calcoalcalino con alto K. El intrusivo Cobrepampa evoluciona por fraccionamiento y contaminación en una corteza más delgada que la superunidad Linga. Petromineralógicamente se tiene epidotización con diseminaciones de calcopirita, pirita y bornita, gangas de cuarzo y calcita con hematita acicular. Las inclusiones fluidas muestran temperaturas de homogenización de 165.5 - 266.43 °C y salinidad 3.5 - 16.8 % eq. peso NaCl de un mesotermal o epitermal, pero que por sus características geomineralógicas sería un mesotermal. Por tanto, Cobrepampa presenta más de un evento de mineralización: una con magnetita y actinolita, y otro mesotermal de vetas de cuarzo con sulfuros.

May 22, 2019

By Oliver Bowles

This paper is the third of a series of reports on asbestos prepared by the Bureau of Mines. The reports already issued contain general information, including descriptions of deposits throughout the world.3/ The present paper deals chiefly with milling and marketing. Many grades of asbestos are marketed, and an important phase of milling is the grading of fiber; these subjects therefore are related so intimately that contiguity in their treatment is fully justified. Although the Bureau of Mines is interested primarily in the mining and preparation of raw materials, the fabrication of asbestos products has attained such importance in the United States that brief reference to processes of manufacture is included. CLASSIFICATION OF FIBER Canadian asbestos fibers are divided into three main groups - crudes, mill fibers, and shorts. The term "crude" is applied to fiber of spinning grade measuring three eighths inch or longer, that is. hand-cobbed and not passed through a mill. Mill fibers are obtained by crushing and beating the fiber-bearing" rock, until the, asbestos is freed and, then removing the fiber from the rock by screening or air separation. Shorts are the lowest grades of mill products.

Jan 1, 1935

Electrostatically charged water droplets efficiently suppress breathable dust produced during open air rock crushing operations, according to recently completed independent tests conducted for the Environmental Protection Agency. Since a primary rock crusher produces very heavy clouds of dust, this application was selected as an appropriate test site to measure the efficiencies of new "charged fogging" equipment in mining and mineral processing operations. EPA's Industrial Environmental Research Laboratory, Research Triangle Park, NC, contracted TRC-Environmental Consultants Inc. of Wethersfield, CT, to conduct a full-scale demonstration of a recently developed electrostatic fogger, designed to project a charged fog spray at distances up to 15.2 m. Test results indicated overall fogger efficiencies of approximately 70%. The Fogger IV* employed in these tests is reportedly the largest charged logger ever made, with an extremely long operating range. The original fogger was designed for indoor dust control; this fourth generation version is designed for fugitive dusts, indoor and outdoor, and has an operating range up to 15.2 in.

Jan 6, 1981

By Dave Minney

The South African mines health and safety regulations require that mine management establish a quality management system for rock support material. Quality control of resin capsules used as a support medium in South Africa is specified under SA National Standards No 1534. Experience has shown that this specification, while addressing the chemical and physical aspects of the products, but does not address the required performance criteria. In order to address this shortcoming, the industry has put a lot of emphasis on short encapsulation pull tests, performed insitu, in the underground workings of the mine. This is also fraught with many shortcomings, particularly as regards site availability, cost and repeatability of results. To try and address these issues, the Department of Mechanical and Aeronautical Engineering at Pretoria University were approached to develop equipment and machinery that could produce reliable, repeatable results in a laboratory environment which reasonably simulates installation practice underground. The test method is based on the ASTM F432-95 Strength Index test, but modified to use push test rather than pull tests. The paper describes development of the test method and the preliminary results and findings of the work.

Jan 1, 2007

By H. J. Uananisa, M. J. Papo, C. W. Siyasiya, W. E. Stumpf

"SynopsisThe need to reduce weight while maintaining good mechanical properties in materials used in the automotive industry has over the years seen an increased exploitation of various steels to meet this new demand. In line with this development, the ferritic stainless steel family has seen a wide application in this industry, with the AISI 436 type increasingly being used for automotive trims and mufflers for exhaust systems, as well as a significant part of this steel’s application being for the manufacture of wheel nuts and wheel nut caps in trucks, mainly through the deep drawing process. However, there have been reports of some poor surface roughening of this material during deep drawing, with tearing and/or cracking also reported in some instances. This has been suspected to possibly be associated with some local differences in localized mechanical properties between grains and grain clusters of the rolled and annealed material.In order to investigate the poor surface roughness exhibited by AISI 436 ferritic stainless steel (FSS) during deep-drawing, Lankford values (R-mean and ?r), grain size, and microtextures of various sheet samples from this steel were studied. The chemical composition range for the samples was 0.013–0.017% C, 17–17.4% Cr, 0.9–1% Mo, and 0.4–0.5% Nb. The steels were subjected to various hot and cold rolling processing routes i.e. involving industrial direct rolling (DR) or intermediate annealing rolling (IR), and the drawability and final surface qualities of the steels were compared. It was found that the DR route gave an average R-mean and ?r value of 1.9 and -1.4 respectively, while the IR route yielded an average Rmean and ?r value of 1.6 and 0.52 respectively. The high ?r value for the DR processing route had a substantial adverse effect on the drawability. IR samples exhibited a smoother surface finish on visual inspection, while clear flow lines were visible on the DR samples, despite the fact that DR is the preferred industrial processing route due to the reduced production costs it offers. This observation was also confirmed through SEM examinations. The difference in the surface quality was attributed to microtexture. However, the mechanism responsible for this difference still needs to be identified."

Jan 1, 2015

A predicted increase in aluminium production and the possibility of a diminishing supply of petroleum coke for anode electrodes in alumina reduction cells makes it desirable to find alternative electrode materials. Browncoal char, with a lower ash content and with an elemental purity similar to petroleum coke, was produced by leaching in hydrochloric acid, washing with water, and charring at 1,150°C. The cost of processing is estimated tobe competitive with petroleum coke.Without further processing the bulk density and real density were undesirably low, but by briquetting the coal before charring and crushing, the bulk density was improved to 92 per cent of the petroleum coke value andthe particle density was improved to 92 per cent of the density of petroleum coke by water displacement or 75 per cent by mercury displacement.Pre-baked electrodes were prepared from the char alone, mixtures of petroleum coke and char, and from petroleum coke alone, all bonded with coal tar pitch.The electrodes were tested for the usual physical properties and were evaluated for performance in a laboratory size alumina reduction cell.Electrodes based on brown coal char alone were found to be inferior in physical properties and performance, but mixtures of the char and petroleum coke, despite poorer density, electrical resistivity, and carbon consumptionon a theoretical basis, in performance tests gave up to 17 per cent better carbon consumption per weight of aluminium produced and 21 per cent better electrical current efficiency than the electrodes based on petroleum,coke alone.It is suggested that larger scale tests are warranted.

Jan 1, 1971

By Jueun Lee, Jong-Hwa Yoon, K. Rider, Bernard J. Martin

Whole body vibration is known to affect movement accuracy [1], however little is known about changes in the organization of movement and movement strategies used to limit the influences of perturbations. The specific aim of this work is to analyze the motion and coordination of upper body segments of seated operators performing reaching tasks under whole-body sinusoidal vibration exposure and simulated vehicle ride motion. The long-term objective is to model reach coordination and predict the dynamic behavior of the upper body motion under vehicle vibration exposure. Method The reach task consisted of pointing with the right hand index finger to targets located on touch screens placed in front of the subject, 45° overhead and 90° to the right in the mockup cabin of an HMMWV placed on a 6 DOF ride motion simulator. The task was performed under stable (no vibration) and vibration (sinusoidal vibration or simulated ride motion) conditions. A motion capture system was used to record kinematic data of reflective markers to recreate body link trajectories. Joint angles (torso, shoulder and elbow; Figure 1) were then computed using quaternions. Coordination between body links was defined as a) the joints angle-versus-angle relationships between the upper arm and lower arm, and b) the joint motion onset relationships between torso, upper arm and lower arm in the time domain. Results Angle–versus-angle relationships. The relationship between upper arm vs. lower arm angle and torso vs. upper arm angle for a far forward reaching movement in the stable (solid lines) and vibration conditions (dotted lines) are illustrated in Figure 2. Fig 2A compares the control condition with a 4 Hz lateral vibration while Fig 2B compares the control condition with a 6 Hz vertical vibration. It appears that under vibration exposure the reduced upper arm extension is compensated by an increase in torso flexion. This effect is seen in the last phase of the movements (encircled areas). In addition, the lower arm extension is delayed under 6 Hz vertical vibration (Fig 2B left panel). Time of joint motion onset. The timing relationship between torso, upper arm and lower arm is largely a function of the target to be reached. Examples of delays between body links are illustrated in Figure 3. The control condition is compared to a 6 Hz vertical vibration for three

Jan 6, 2006