Search Documents

By Mark Osborne, Ray D. Peterson, C. Edward Eckert

"The theoretical melting energy requirement for a typical hypoeutectic aluminum-silicon alloy is approximately 520 BTU/lb. It has been demonstrated, however, that even a state of the art secondary processing-automated lost foam casting operation can exceed this value by at least an order of magnitude when the actual thermal energy input from melting to solidification is monitored. Metal transfer and holding operations constitutes over 65% of this expenditure. The authors present relative benchmark energy expenditure information by unit operation for an offsite melting/lost foam casting line with a daily throughput in excess of 100,000 lbs. Efficiency improvements through optimization of the current process, and anticipated energy values at the culmination of a U.S. Department of Energy sponsored project to develop, integrate and demonstrate an advanced melting, transportation, and dispensation system will be cited.IntroductionThe size of the U.S. aluminum remelt pool was approximated to be 14.21 billion kg (31.27 billion pounds) by a recent study?, with the engineered castings (foundry) sector accounting for 3.25 billion kg (7.16 billion pounds) or 23% of that total. This study considered overall process yield and all major contributors to scrap. The values cited, therefore, are more meaningful than simply tabulating annual pounds shipped by sector.The foundry sector consists of Sand Castings, PM Castings and Die Castings categories appearing in Figure 1. All other categories comprise the wrought alloy sector. Wrought alloy production enjoys an energetic benefit from both scale and a relatively continuous operation. Many foundry operations, however, operate in batch mode at less than design metal throughput with characteristically longer melt holding periods. Since any detention of molten metal beyond melting represents an overhead use of energy, melt holding (secondary) energy expenditures can appreciably inflate melting energy requirements in the foundry."

Jan 1, 2009

By Zhigang Liang

Investigation into the mixing of 150t ladle furnace by two-nozzle jetting was performed by a water model simulation of 1:4. The effects of nozzle arrangements including separation angle, radial position and asymmetry as well as tracer adding position on the mixing time were studied. The most favorable mixing is achieved when the two nozzles are symmetrically arranged at half radii in the ladle, with 45o separation angle. The empirical relationship between the mixing time and stirring power intensity has been established for two-nozzle jetting based on the present experimental results. In addition, the swelling above bath surface is also investigated with two-nozzle jetting.

Jan 1, 2009

By Xiang-yang Zhou

Keywords: Low-Grade Dolomite, Low CaO Content, High Specific Surface Area, MgO. A low energy consumption preparation technology of magnesium oxide with low calcium oxide content and high specific surface area from low-grade dolomite has been investigated. The optimum technical conditions for the preparation of magnesium oxide are the followings: dolomite is partially calcined at 750-800° for 2 h; the optimum solid-liquid ratio range in calcined dolomite slurry is 20-30 g?l?1; carbonation temperature, carbon dioxide pressure and end point pH value of carbonation are less than 40°, 0.4-0.6 MPa and 7 respectively during carbonation process; decomposition temperature of Mg(HCO3)2 solution is near 100°; calcination temperature of the precursor (i.e. precipitated basic magnesium carbonate) is less than 850°. More than 90% of magnesium can be extracted by the technology. The MgO product (CaO < 0.38%) with a specific surface area of near 50 m2?g?1 also can be obtained by the technology.

Jan 1, 2005

By Christophe Thiébaut

Keywords: Pyrochemistry, Salts Treatment, Distillation The pyrochemical purification of metal generates spent salts. When this metal is an actinide such as plutonium, the slags cannot be discarded and are thus disposed in nuclear facility. In order to handle with these slags, the decision has been taken to reduce stored quantities. The development of a pyrochemical treatment is in progress in the CEA Valduc centre. The feed salt, typically composed of various Pu and Am species contained into monovalent or divalent chloride matrix, is first oxidized to convert the actinides into oxides. Then the chlorides are separated from the actinide oxides by vacuum distillation. Temperatures higher than 750°C for monochloride salts mixture NaCl/KCl and higher than 1100°C for divalent CaCl2 base salts, are required to produce an industrial flow of vaporization. Inactive qualification of the process for NaCl/KCl base salt has been carried out with lanthanide surrogates. Then, a pilot equipment, called distillator has been designed and built for production-scale distillation of NaCl/KCl and CaCl2 oxidized plutonium salts. Industrial flows of vaporization have been obtained with this pilot equipment : about 4 g/cm²/h for NaCl/KCl at 800?900°C and 1 Pa, and more than 1,5 g/cm²/h for CaCl2 base salts between 1000?1200°C at 0.1 Pa. The last step, now in progress, is the integration of the distillator into a glove box.

Jan 1, 2005

By H. Doostmohammadi

During the tapping of liquid steel from Electric Arc Furnace (EAF), some slag is carried over into the ladle. High levels of FeO and MnO in slag carryover increase the oxygen activity in steel melt leading to oxide inclusion formation during the ladle treatment. The demand on cleaner steels requires minimization of carryover slag. In this work, the effect of EAF slag carryover on ladle slag-steel equilibrium calculations for a hot working tool steel was studied. Steel and slag sampling were done in Uddeholm Tooling AB in Sweden. XRF and OES techniques were used to determine chemical composition of samples. The quantity of slag carryover was calculated based on a mass balance followed by thermodynamic calculations on metal-slag equilibrium using Thermo-Calc software. The agreement between predictions and experimentally determined compositions was good. This leads to the development of a prediction method for optimizing the production of other tool steel grades.

Jan 1, 2009

By Lucas Lopes da Costa

In this work, a natural foam extracted from the Amazon buriti palm tree is investigated as possible substitute for synthetic foams. The basic physical and mechanical properties of this biofoam were evaluated. Its sponge-like structure was characterized by the amount of pores and morphological aspects. It was found that the buriti biofoam displays a very low density of the order of 0.1 g/cm3 with a relatively good compressive strength. This would be suitable for several engineering applications and as a new material with the potential for replacing currently applied synthetic polymeric foams.

Jan 1, 2010

By Sergio N. Monteiro

Polymeric matrix composites with dispersed hard particles are being as wear resistant tools in industrial polishing operations. In the present work, the microstructure of epoxy composites with different amounts of embedded diamond particles, up to 30 wt.%, was investigated for the effect on fracture characteristics. It was found that the introduction of diamond particles promoted an increase the porosity of the epoxy matrix. Moreover, the particle morphology associated with a non-uniform distribution within the matrix was responsible for the nucleation of cracks that caused rupture of the composites.

Jan 1, 2006

By J. Samir

The objective of this study is to simulate the isothermal filling up of moulds by a RTM process when adopting CV/FEM and VOF method and when also taking into account the presence of obstacles coupled to the effect of the thickness and reinforcement layers variation. The codes developed intended to ensure an optimal positioning of the injection points and of the vents and also to determine optimal injection pressures, in order to minimize the cycle times. These codes use a mesh generator proper to the team, allowing a discretization of the domain in triangular unstructured elements, with the possibility of a local refinement and inserts inclusion.

Jan 1, 2009

By Y. Zhoa

The surface morphology of materials is of fundamental importance to many surface related applications, such as wetting, friction, reflection, drag, and adhesion. Various approaches for micro/nano patterning atop polymer surfaces have been proposed in recent years. However, a cost effective technique is still highly in demand. In this paper, we demonstrate a novel but rather simple and generic approach for surface micro/nano patterning using shape memory polymers (SMPs). Different types of novel patterns are realized and their 3-D surface features are quantitatively analyzed by a PLµ Confocal imaging profiler.

Jan 1, 2010

By Vinay Kumar

The present investigation describes R & D studies carried out for recovery of copper from the sulfate solution expected from the leaching of e-wastes in presence of minor constituents such as cadmium, zinc and nickel using solvent extraction process. In order to extract copper in continuous mode in mixer settler unit (MSU), basic studies have been made to optimize the experimental condition using 5%LIX84 in kerosene. Subsequently, the solvent extraction of copper was made in MSU maintaining leach solution flow rate 4.0 L/h and A/O ratio 1. The results showed complete extraction (~97%) of copper in three stages at A/O ratio 1 from the aqueous solution containing 1.98g/L Cu at pH 1.91 in presence of impurities. Loaded metal was completely stripped after scrubbing with 10% sulfuric acid in two stages. The stripped solution could be used for metal/ salt recovery by electrolysis/ crystallization.

Jan 1, 2010

By Yushiro Hirai

Saganoseki smelter & refinery had operated two flash smelting furnaces from 1973, attaining 330,000 mtpy of copper production in 1989. In 1996, however, it carried out a "integration of two flash furnaces". That is, it doubled the feeding capacity to one flash furnace to shut down another furnace while maintaining the same production. Single flash furnace operation has successfully started in March 1996 accomplishing a great reduction of the total production cost. The production had reached to 350,000 mtpy in 1997, and further increased to 450,000 mtpy by executing the expansion program with single flash furnace in 1998. This paper introduces results of the single flash furnace operation and describes about an outline of the expansion.

Jan 1, 1999

By Tianjiao Luo

Some literatures discussed on how to recycle the various reagent, but the discussion on how to reuse the waste liquid directly is very little. How to reuse the waste liquid directly was researched in this paper. Firstly, the waste liquid should be filtrated to remove the impurity; then some quantity of H2O2 solution was dripped into the waste liquid to pretreat it; finally, CuSO4solution was added into the treated waste liquid and the pH was adjusted to about 12, then some HCHO solution was added into the waste liquid, in which the treated carbon fiber can be plated. The morphology and composition of coatings were investigated by means of Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS), the deposition rate was mensurated by the way of dissolution. The results indicated that, the plating effect was basically identical with new plating solution, and the solution is stable, and the plating rate is still about 0.8µm/h, and the copper coating is even and combines closely with carbon fiber. According to this way, the waste liquid can be reuse 5~7 times.

Jan 1, 2006

A molten metal granulator was designed and fabricated at the U.S. Dept. of Energy, Albany Research Center, for granulation of precious metal-bearing alloys and slags. The system was designed to safely granulate a metal alloy at a temperature of up to 1,600°C at a rate of roughly 50 kg of alloy per minute. The primary water jet was supplied by a 18.6-kW, 600 liter per minute pump which provided approximately 600 kg of water per minute through the primary jet. Two 3.7-kW, 150 liter per minute auxiliary pumps provided additional wash water to wet the granulation trough through 4 secondary jets, which were placed at either side of the primary jet. The water supply was closed-loop, including a 37,850-liter supply tank and 22,710-liter recovery tank. Magnetic separators and particulate filters were included for collection of the finest fraction of the granulation product, which cleaned the water sufficiently for continuous recycle.

Jan 1, 2006

By Xiangjun Zuo

This paper firstly reviewed the state of the art in the recycling of used Printed Wiring Boards (PWB), and then presented part of the authors study on the combustion of PWB powders with and without the addition of catalyst. During the combustion of PWB powders without catalyst addition, there were two obvious exothermic reactions, one at 300-380oC, the other at 450-500oC. With the addition of catalyst during PWB combustion, there were no obvious exothermic reactions, indicating that dehalogenation reactions are not exothermic: The results showed that NaHCO3 and CaCO3 were very efficient to control the emission of Br2 and C6H6, lowering 80% compared to the case without catalyst, Na2CO3 can slightly control the emission of Br2 gas but not for C6H6 gas mission, and NaOH has no any effect of the control of both gases.

Jan 1, 2009

A sinter plant baghouse dust has been treated as a hazardous solid waste, and disposed at a very high price. A series of leaching tests were conducted to examine the possibility to produce high grade potassium chloride from the solid waste. It is found that around 40% of the solid wastes can dissolve into water, and a deposit with more than 90% KCl can be produced after simply drying the solution.

Jan 1, 2009

By Junfeng Shen

Geosynthetic clay liner (GCL) is a kind of waterproofing material used widely in engineering. The waterproof mechanism is understood in terms of bentonite particles becoming a water-obstructcolloid layer after they absorb water and swell. The swell stress, however, has not been determined directly till now. In our experiment, the swell stresses of the GCL under saturated and water absorbing conditions are measured directly using a custom-made instrument. The results show that (1) the instrument designed by the authors performed satisfactorily and the test results are reproducible; and, (2) The trend line of swell stress variation with time can be divided into three segments. The first segment is characterized by a quick increase of the swell force in the first 0?50 hours. The swell stress increases by 7.00×10-4?1.00×10-3 Mpa / hour. The second segment shows a slow increase of the swell stress during the 50?1730 hours. The swell force increases by 7.54×10-6?2.02×10-5Mpa / hour. The third segment is characterized by little variation in the swell stress after 1730 hours. In this segment, the average value of the swell stress measurements is 0.0719Mpa and the maximum value is 0.0729Mpa. It is suggested that the swell stress is mainly raised by water entering the pores among montmorillonite particles and the interstitial layers in individual montmorillonite crystals, leading to an increase in volume and manifested as a stress on the surrounding materials.

Jan 1, 2006

By David Norval

Ni, Co, Cu and Pt, mattes are common materials that require granulating and milling of the resultant granules for further processing. This route is acceptable if the material is brittle (friable) which is a property associated with the higher sulphur mattes. For lower sulphur levels, where the matte is less amenable to milling, the costs of the milling increases. This paper will compare water granulation with certain dry granulation processes and the downstream processes required for Hydrometallurgy. It will further introduce and expand on atomisation which offers a further safety benefit in the control of the metal flow into the &apos;wet zone&apos; with the use of a tundish flow control also reducing the conversion from the matte to powder in one fairly straightforward operation.

Jan 1, 2006

By Chen Song

Keywords: Co3O4, Cobalt Compounds, Morphology, Urea, Homogeneous Precipitation Depending on experimental condition, precipitation from cobalt nitrate and chloride solution in the presence of urea yield dispersed cobalt compounds with different chemical compositions and morphologies. The effects of concentration of cobalt solution and urea, agitation, on precipitation morphology were investigated experimentally. Generally in closed systems the particles are identified as cobalt (II) basic carbonate with needle type shape. In open system, spherical and plate-like precipitations of cobalt (II) basic cyanate are formed. The chemical formula of cobalt compounds was confirmed. They are CoII,III(OH)0.83(CO3)0.49 Ay?0.14 H2O (in tightly-capped reactor: A stands for NO3?, Cl?; y[A]molecular weight < 12.9) and CoII,III(OH)0.83(NCO)XAy?0.14 H2O. (in open reactor A stands for: NO3?, Cl?; 42 x + y[A]molecular weight < 44.82). The main reason was that the primary particles had different chemical compositions for the effects of the different kinds of anions and stoichio-chemical compositions of the primary particles. The effect degree of the anions depended on the co-existing anion radius in the reaction solution. According DTA-TG analysis of the cobalt compounds, the latter particles transform to Co3O4 powders on calcining. The shape of the Co3O4 particle with porous character has inheritance with precipitation. In this paper, it concludes that the particle formed by the principle of nucleation-aggregation in aqueous solution. The process of aggregation has played an important role in formation of particles. During calcination, the aggregation would be destroyed partly.

Jan 1, 2005

By C. J. Newman

In January 1999, a redesign of the Kennecott Flash Converting furnace settler was initiated to enhance furnace integrity and extend furnace life. This furnace uses Kennecott-Outokumpu Flash Converting technology to produce copper directly from copper matte. A detailed assessment was made of all technology available around the world before making a decision on the design features to be incorporated in the new design. The new design includes the following: redesign of all sidewall cooling elements to include the latest cooling element technology; redesign of the furnace hearth to include a stadium hearth at the reaction shaft end of the furnace; redesign of the furnace hearth to include a stepped hearth design adjacent to the furnace sidewalls; addition of flat settler roof cooling elements .around the reaction shaft; replacement of reaction shaft transition elements with an improved design and improvements to the furnace cooling element monitoring systems. The Flash Converting furnace was shut down on a planned basis in July 2001 to implement these improvements after 29 months of operation, converting more than 1,000,000 tonnes of matte. During the 30 day shut down, the improvements were successfully completed, with furnace start up in August 2001

Jan 1, 2002

By Tian Sugui

By direct aging treated, creep properties measurement and microstructure observation, the influences of the direct aging treatment on the creep behaviors of Hot Continuous Rolled GH4169 superalloy are investigated. Results show that the creep resistance of Hot Continuous Rolled GH4169 superalloy may be obviously improved by directly aged treatment. Under the applied stress of 700MPa at 660, the creep lifetime of the alloy is enhanced to 126h from 60h. During hot continuous rolling, the deformation features of the alloy are the twinning and the double orientations slipping of the dislocation activated within the twinning regions. After direct aging treated, the alloy displays a smaller grain size, and the finer g² phase is dispersedly precipitated in the matrix of the alloy, which is thought to be a main reason of enhancing creep lifetime of the alloy.

Jan 1, 2010