Search Documents

By In-Hyeok Choi

Currently, spent V2O5–WO3/TiO2 catalysts contribute significant amounts of solid waste following increasing levels of global demand. V2O5–WO3/ TiO2 catalysts usually consist of TiO2 anatase as a supporting oxide, vanadium as a catalytic agent, and other promoters such as tungsten, silicon, and calcium. Although vanadium is the main catalytic agent, a relatively high content of tungsten (WO3, 7–10 wt%) typically exists compared to vanadium (0.5–1.5 wt%). Considering the irreplaceable properties and industrial importance of tungsten, a feasible method for the recycling of spent V2O5–WO3/TiO2 catalyst should be established to utilize it as a secondary source. This paper presents a process to recover tungsten from spent V2O5–WO3/TiO2 catalyst. The processes proposed here involving roasting, decomposition using HCl, ammonia leaching, and crystallization. Within the process, ammonium paratungstate (71 wt% as WO3) is obtained as a final product. The total yield rate of tungsten from feedstock was found to be 96.3%.

By J. H. Corrigan

A series of six papers describing the Falconbridge Dominicana Ferronickel project were presented at the International Laterite Symposium held as a joint project of TMS-AIME in February 1979 at New Orleans. A review of the ore mineralogy, as well as. the processing and environmental practices as they exist today at Falcondo with emphasis on modifications put into practice since 1979 are presented in two papers: Part I.- Mineralogy and Ore Dressing E.W. Lithgow - General Superintendent ? Mines Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, X- ray amorphous materials. Minor constituents are hematite, gibsite, olivine and enstatite. In the Ore Dressing plant, the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock kagments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing. Part II.- Pyrometallurgy, Fuel and Power Generation J.H. Comgan - Manager ? Production Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Falcondo's energy requirements are based on oil which is refined on site to provide distillate to carry out drying and selective reduction of the nickeliferous ore in the shaft furnaces, plus bunker oil to produce electrical power for process melting, refining and ancillary use. The dryer product at 1.68% Ni is briquetted and passed counter current to hot reducing gas in 12 vertical shaft furnaces. The hot calcine discharge is melted in two high power electric furnaces at very high secondary voltage. The crude ferronickel is ladle refined and cast as 15 kg ingots or 125 gm ferrocones.

Jan 1, 1993

By Heikki K. Jalkanen

Thermodynamic properties of copper-iron mattes and slag-matte distribution of copper and some minor matte constituents (Ni, Co, Mo, As, Sb and Bi) are discussed on? the basis of equilibrium measurements: a change from. oxidic to sulfidic solubility as the predominant form of dissolution of copper takes place as matte grade decreases. Distribution coefficients of minor matte constituents are complex functions of sulfur and/or oxygen potentials?. The distribution behaviour of different? metals can be qualitatively derived from their affinities to copper and stabilities. of their sulfides and oxides. The equilibrium results are compared with commercially observed values. from Outokumpu.Oy flash smelting furnace.

Jan 1, 1983

By E. C. T. Chao

Micro-optical and synchrotron radiation-induced X-ray fluorescence (SXRF) techniques have been used to study unoxidized and oxidized samples of Carlintype sedimentar,y rock-hosted disseminated gold ore. In these samples, Where much of the gold is submicroscopic, the SXRF technique, which has a spatial resolution of about 20 ~m and a minimum detection limit (MDL) in the ppm range, is an ideal and necessary tool for precisely locating gold-rich areas in a sample. Gold-rich areas pinpointed by SXRF were later studied in detail by micro-optical methods, principally optical microscopy and scanning electron microscopy with energy-dispersive X-ray analysis (SEM-EDX). In two unoxidized and one oxidized ore samples, SXRF analyses have shown gold to be present predominantly in discrete clay-rich and silicified areas. Gold was not detected by SXRF in association with pyrite or carbonaceous materials. SEM-EDX examination of the gold-bearing areas in the unoxidized samples succeeded in identifying only two free gold particles, 0.2 and 0.5 ~m in size. In the oxidized sample, gold particles appear to be larger (but still submicroscopic) in average size and more evident in micro-optical examination after SXRF location of goldbearing areas. The findings of these studies may help to improve the efficiency of processing and recovery of gold from unoxidized ores.

Jan 1, 1987

By Duclerc Fernandes Parra, Vijaya Kumar Rangari, Washington Luiz Oliani, Danilo Marin Fermino, Ademar Benevolo Lugao, Nilton Lincopan, Luiz Gustavo Hiroki Komatsu

Polyethylene is widely used for packing applications. Different grades of polyethylene, LLDPE and LDPE play a major role in the film blowing industry. The use of nanoclay in polymer matrices (non-polar) requires the use of a compatibilizer agent, ethylene graft maleic anhydride copolymer (PE-g-MA), which acts as a bridge for nanoclay-matrix-interaction. In our study, blown films of LLDPE, LDPE, and their blends were produced using a twin screw extruder. The combination of PEs as matrix, montmorillonite (MMT) and silver nanoparticles (AgNPs) intended to improve mechanical and thermal properties. Nanocomposites films with 1 wt% of montmorillonite and 0.5–1.0 wt% silver nanoparticles were prepared by blow extrusion and evaluated. Nanoclay intercalation/exfoliation degree was investigated by X-ray diffraction spectroscopy (XRD) and scanning electron microscopy (SEM). Mechanical and thermal properties were evaluated. The results showed optimum dispersion at intercalation/exfoliation levels for polyethylene nanocomposite (PENC), slight increasing in mechanical and especially improvement in thermal properties.

Mar 1, 2017

By Yuanbo Zhang, Zhixiong You, Guanghui Li, Peidan Wen, Tao Jiang

Sn-bearing iron ore containing small amount of Zn, Pb and As is one of the typical complex polymetallic ores in China. This kind of ore is not extensively utilized due to the complicated relationships between iron and other associated nonferrous metal minerals. Excessive contents of these elements would adversely affect the metallurgical operation as well as the quality of steel products. In this study, reduction behavior of Sn was detailedly investigated using H2 or mixed H2/CO as reductant. The results revealed Sn volatilization was improved in the presence of H2 than individual CO/CO2 atmosphere. Simultaneous volatilization of these elements was realized by roasting under weak H2/CO reducing potential, and metallization reduction was advantageous for further Zn volitilization. A metallic pellet (DRI) with Fe metallization greater than 90%, residual Sn, Zn, Pb and As content of 0.054%, 0.012%, 0.0045% and 0.09% was prepared via a simulated reducing gas of coal gasification.

Jan 1, 2015

By Laurentiu Nastac, Ruslan Mudryy

"This paper investigates the solidification of cast energetic materials. An active cooling and heating (ACH) technology and a mechanical vibration (MV) technology were applied to achieve unidirectional solidification during casting and to reduce cracks, gas pores, and shrinkage defects. The design parameters of these technologies were developed via Computational Fluid Dynamics (CFD) modeling and thermal stress analysis. Concerning the ACH technology, the number of cooling/heating sections and their temperature profiles and time sequences were optimized based on the thermo-physical properties of the energetic material as well as the riser and mold diameter, thickness and type. The ACH technology will also decrease the thermal stresses during casting of energetic materials and therefore minimize the formation of potential cracks that may form during the casting process. The MV technology will help to remove air entrapped during pouring process and decrease the detrimental gap size between the projectile and the solidified energetic material.IntroductionCasting processes are widely employed in the manufacture of products with intricate shapes and, in particular, in applications where the material of the final product is sensitive to machining. It is especially useful in processing of energetic materials. The cooling conditions applied in the casting process can affect the quality of the final cast in terms of void formation, residual stress distributions, and mold separation. Substantial shrinkage is also observed due to the density change upon solidification [1-3]. Residual stresses are known to be closely related to the formation of cold cracks and hot tears during casting. The formation of a gap between the mold and the cast material is of critical importance due to its deleterious effect on heat removal and on crack formation. In the casting of energetic materials all these defects can significantly impair the detonation velocity, Gurney energy, and insensitive munitions characteristics of the formulation, and lead to catastrophic accidents in explosives handling [ 4-5]. Imposition of carefully controlled cooling condition is thus critical in optimizing the cast quality that could help avoid such destructive effects."

Jan 1, 2013

By Demaerel. J. P.

Arsenic plays a major role during electroreflning of copper. Both the arsenic content in the anode and the arsenic concentration of the electrolyte have, in conjunction with other impurities such as lead, antimony, bismuth and oxygen, a direct influence on the quality of the cathode. The mechanisms are currently slime. inclusion and precipitation of insoluble compounds in the bulk of the electrolyte. Arsenic has also been reported to have a depassivating effect on the anode. An influence on the anode slime adhesion has also been found. A literature survey is given and these data are compared with and completed by our own results based on lab and pilot scale experiments as well as on Olen tank.house practice.

Jan 1, 1987

By Animesh Jha

The carbothermic reduction of chalcopyrite has been studied in the temperature range 1073 to 1273K in presence of lime. The role of lime during the reduction process is explained and the phase equilibria leading to the metallisation of copper and iron are discussed. The effect of coal and carbon monoxide on the reduction process have been studied and the rate governing steps are identified. This investigation also cites examples of possible mechanisms of physical separation of metallic Cu from iron during the reduction process.

Jan 1, 1992

By Samson Adeosun, Sanmbo Balogun, David Esezobor

"Iron and steel making processes give rise to large amounts of usable and unusable materials, the latter generally being termed wastes. It is sometimes difficult to distinguish between re-usable by-products and wastes which cannot be sold or land-filled. Much depends on circumstances such as the local market for the material. This can itself vary from time to time with by-products which cannot be used or sold becoming wastes and vice versa. This paper defines the concept of “waste-free technology”, discusses its development in the steel industry and highlights the benefits of the technology to the manufacturing sector and the environment. The paper also articulates how the “waste-free” technology could be applied in the proposed Ajaokuta integrated steel plant in Nigeria.IntroductionIn the past, nature was considered an inexhaustible store. Its resources were consequently exploited and waste products therefrom were discarded. Today, attitudes have not changed appreciably even as raw materials cost rise by the year to pose a series of socio-economic problems, which, among others, may include the rational and optimum utilization of resources, environmental protection and reduction of waste formation. Consequently, industrialists now face unexpected regulatory pressure in areas of pollution prevention, waste minimization and hazardous waste disposal.Iron and steel making processes give rise to significant amounts of usable and un-usable materials, the latter generally being termed waste. It is sometimes difficult to distinguish between re-usable by-products and wastes which cannot be sold or land-filled. Much depends on circumstances such as the local market for the material. This can itself vary from time to time with by-products which cannot be used or sold becoming wastes and vice versa. In this paper, the term waste refers to those materials that are either irrationally utilized or, land-filled and part of the byproducts that are not utilized. It includes that part of used materials which is not incorporated into the products manufactured during a process stage and which in contrast to reuseable materials, is considered not suitable for any further use, owing to technical or economic factors. In general, these materials are inorganic and parts of them are either utilized or passed to the other processes; the other part should be disposed of using well-established waste disposal practices to avoid any environmental threat.Thus, creative methods must be developed to modify the manufacturing processes to reduce emissions and process wastes by fully utilizing all resources. One method of eliminating the negative effect of waste formation is the use of purification and cleaning structures (pollution control system, PCS). These are, however, quite expensive."

Jan 1, 2008

By Yurniko Nakamura

Hydriding properties and crystal structure of a Ti-V- Mn solid solution alloy have been studied by P-C isotherm measurements and neutron and X-ray powder diffraction. The absorption P-C isotherm at 298K shows two plateau regions at 0.01MPa and 1MPa. The X-ray diffraction data have demonstrated that three phases with a BCC, a pseudo-cubic FCC and an FCC structure form subsequently with increase of the hydrogen content. Crystal structure of the latter two phases has been determined by Rietveld refinement of the neutron diffraction data. The FCC phase is the di-hydride of CaF2 type with hydrogen occupation in the T sites. The pseudo-cubic FCC phase is the mono-hydride of NaCl-type with hydrogen occupation in the 0 sites, which has not been reported so far. The lattice constants of the mono-hydride (Ti1.0V1.1Mn0.9)H_2.7 are a'=0.407 nm for two axes and c'=0.390 nm for the third axis. The a'axis is shorter by 4% than the c'axis. This pseudo-cubic FCC lattice is formed by contraction of 5% of the a axis and expansion of about 30% of the c axis from the original BCC lattice.

Jan 1, 2002

By John A. Clark, Danylo Oryshchyn, Casey Carney, Stephen Gerdemann, Cathy Summers, Thomas Ochs

"Limited analysis of combustion gas streams where carbon capture is not of interest is done mainly to ascertain operation parameters. Stringent regulations on acid gases and particulates promote careful flue gas analysis. Unregulated components are typically not analyzed. Typically not more than four points (two in the boiler, and one each in the flue and the stack) are sampled. A successful oxy-fuel process with carbon capture and compression is anticipated to require as many as 12 sample points with analysis for water, nitrogen, oxygen, argon, NOx, SOx, and carbon monoxide. Carbon dioxide captured for beverages produces a high value product and the cost associated with analysis is warranted. However, carbon capture for disposal must keep all costs to a minimum. This paper will compare alternative approaches for cost-effective sampling and analysis of the carbon dioxide product streams from oxy-fuel combustion, through all stages of production through compression and pipeline/vessel delivery.IntroductionAnalysis of gases in an oxy-combustion process with carbon capture is essential to the operations of the oxy-fired boiler and the subsequent collection, compression, and purification of carbon dioxide. The process is charged with pure oxygen and not-so-pure carbon in the form of coal at the front end, generating a product of mainly carbon dioxide with traces of argon, nitrogen, sulfur compounds, nitrogen compounds, oxygen, hydrogen, and mercury. It is possible that hydrogen chloride and hydrogen sulfide may also be present in trace amounts [1]. The trace components primarily come from impurities contained in coal such as water, sulfur, nitrogen, and volatile organic compounds. Coal also contains a good deal of mineral matter that is transformed into ash during combustion, becoming particulates that can complicate the analysis regimes utilizing standard analytical equipment."

Jan 1, 2010

By B. J. Zhao, F. L. Han, L. E. Wu, M. Chen, Y. H. Chen

Magnesium is the lightest structural metal with a density only two-thirds of aluminium and one-quarter of steel. It can be produced by electrolysis of fused magnesium chloride or high temperature reduction of the oxide. The predominant method for magnesium production is the Pidgeon process which is a batch process starting from calcined dolomite and ferrosilicon. CaF2 is commonly used in the process as the catalyst. Analyses of the slag samples and thermodynamic calculations indicated that liquid phase plays important role in the reduction process. Effects of chemistry, temperature and gas pressure on the production have been discussed and compared with the operating data. Understanding of the reaction mechanisms will provide a fundamental base for alternative processes of the magnesium production.

Mar 1, 2017

By Kathryn A. Mrotek

The textural growth patterns of nodules from two areas in the North Pacific and the South Pacific are characterized by mottled, columnar and compact-type zones. Amorphous material (mainly iron and manganese hydrox-ides) is a botryoidal-forming phase in the mottled and columnar zones. Crystalline material (platy crystals of birnessite and crystallites of todo-rokite) is found primarily in the mottled zones on botryoidal structures or as long-protruding structures growing onto that portion of the nodule in contact with the underlying sediments. The long-protruding mottled zones contain little or no biogenic debris, suggesting that these zones grew un-interruptedly within the underlying sediments. The coalition of spheroidal knobs comprising some of the nodules also suggests a relatively long residing time within the sediments. It appears that crystalline material (the usual host to associated valuable metals) forms in a quiet environment and as a result of direct nodule association with the underlying sediments.

Jan 1, 1982

By LuisW. Pommier

The industrial wastes generated by the plating industry, the circuit board manufacturing industries and other related industries normally contain high concentrations of metals, which make them hazardous. The extraction of the contained metals and their separation may be achieved by both pyro and hydro metallurgical processes. Some of the industrial wastes, those rich in some metals like nickel for instance, are being treated like mine ore concentrates and are being fed to smelting furnaces. The slags from these smelter operations are hazardous. They have, however, special environmental dispensations issued by the regulatory authorities. Hydro-metallurflcal processes have been reported. They also generate a residue which is hazardous because not all the valuable metals are leached out and also, because "non valuable" components, like chromium, are less readily leached. Residues from the plating industry, containing nickel, copper. zinc, iron and chromium as the major constituents and also sodium and calcium, together with cadmium, cobalt, lead. manganese, magnesium, molybdenum, and potassium, have been processed for the extraction of the valuable components. The generation of electrolytic nickel, copper and zinc and also of ferric chloride and chromium oxide is reported. The operation is achieved by a caustic leach for the extraction of zinc, followed by a sulfuric acid leach for the extraction of nickel and copper. This acid leach also extracts the iron and some chromium. The nickel copper and zinc are rendered pure by electrolysis, the iron is oxidized for the production of ferric chloride and the chromium is recovered as an oxide. The leaching operation is performed in two stages, first at a pH of 2.5 to generate an electrolyte for the partial recovery of the metals and then at a pH of 0.5 for the complete extraction of the metals. This leaching operation generates a residue, which although small in volume compared to the initial feed, still contains traces of the valuable metals and a portion of the chromium which makes it hazardous. Additional leaching with hydrochloric acid or nitric acid is required for its complete dissolution. The other minor constituents mentioned are present in concentrations each of less than 0.1% and are handled as impurities in the process. The metals which are soluble at a pH 0.5 and precipitate between 0.5 and 2.0 are bled off. Other impurities will concentrate on the raffinate from the solvent extraction operations from whence they are bled off. These bleeding streams are hazardous and the "impurity metals" are now present in concentrations which would make them valuable, however, the size of these streams is so small that they do not warrant their processing, however they could be marketed to specialized smelters. The extraction of the valuable metals, of the hazardous constituents, the generation of a marketable mixture of minor constituents and the production of a non-hazardous residue for declassification is profitably achieved.

Jan 1, 1998

By Victoria Vaccarezza, Corby Anderson

Due to the demand for rare earth elements for everyday technology and applications, there has been much research initiation into the extraction and recovery of rare earth elements. An otherwise unknown mineral, eudialyte is a zircon silicate consisting of rare earth oxides, specifically the heavy REO yttrium (III), with only trace amounts of thorium and uranium. The first part of this project aimed at finding an efficient way to liberate and upgrade eudialyte to concentrate the REO content. A combination of gravity and magnetic separation techniques were employed, resulting in limited success. The second part looked at the hydrometallurgical processing of eudialyte through various leaching experiments with sulfuric acid. In all, this project will discuss why certain processes were utilized over others, as well as the difficulties that arose during processing.

Mar 1, 2018

By V. Yahorava

Mintek has developed a non-destructive Resin-in-Leach method for the recovery of Rare Earth Elements (REE) from phosphogypsum (PG) waste dumps. However, PG from different sources was found to be highly variable in terms of REE recovery and physical properties. Development of a pre-treatment process was initiated to improve the robustness of the current REE recovery process in order to render it effective for any type of PG. Extensive research into the mineralogy of REE associations with PG revealed that the majority of REE are trapped inside phosphogypsum clusters which inhibits their recovery. Hydrothermal treatment of PG-containing slurry was found to result in re-crystallisation of gypsum with the release of REE phases encapsulated in it. This process was tested on various PG samples and subsequent REE recoveries improved from 5 to 80%. This approach carries a large potential for unlocking value associated with gypsum dumps worldwide.

By Peter Stiaszny, Andrej Samoilov, Yuri Titovets, Gottfried Hribernig, Nikolai Zolotorevskii

"The model has been developed to simultaneously predict both transformation product portions and mean ferrite grain size from the same common · principles as a result of the austenite decomposition during any cooling path of dual phase steels. The transformation products considered are polygonal ferrite, pearlite, bainite and martensite. The model is based on the classical equations of nucleation-growth theory and also contains some empirical parameters. The chemical driving forces for nucleation and composition of elements at the phase interfaces are derived by computation thermodynamics. The empirical parameters related to the model were determined on the basis of a series of austenite transformation dilatometric curves and grain size measurements for continuous and interrupted cooling of several steel types. The model is aimed to predict phase transformation in the complex cooling conditions of the run-out table of the hot strip mill at YOEST-ALPINE STAHL LINZ GmbH as a part of the computer aided system for prediction and on-line controlling of the mechanical properties of hot-rolled strip.IntroductionThe term ""dual phase steels"" is used to refer to a steel consisting essentially of a dispersion of martensite in a fine-grained ferrite matrix. These steels are of increasing technological interest since they provide a better combination of strength and ductility than any other conventional steel sheet material. The strength is important because it offers an opportunity to produce lighter components, while good ductility is needed to permit easy forming of components. It is generally recognized that martensite plays an important role in determining the strength level of dual phase steels. A full understanding of the role played by the phases in determining such characteristics requires investigating in more detail how to optimize the martensite level of such steels, while maintaining good ductility remains the subject of continued research in the industry."

Jan 1, 2000

By K. Yarnaguchi

In the Mitsubishi Continuous Copper Converting Furnace, calcium femte slag is used. Due to its extremely high basicity, the improvement of corrosion resistance of the refractory lining is in need. In order to clarify the corrosion mechanism and to search for a new corrosion resistant material, first, the surface snuctures of bricks corroded in molten slags were observed by EPMA. Second, the dissolution behaviors of sintered MgO-based pellets containing various oxide additives were examined. It was found that the formation and the dissolution of magnesiofemte at the surface of the bricks play an important role in their corrosion and an addition of NiO, Mn02, or Ti02 to MgO is effective in stabilizing the magnesio-femte and improving the corrosion resistance of MgO.

Jan 1, 1994

By Chonghe Li, Pengyue Gao, Xionggang Lu, Juyun Kang, Wajid Ali, Guangyao Chen, Ziwei Qin

A refractory U–Mo associated ore containing jordisite which enclose U, Mo component, and impede penetration, diffusion process of leaching, oxidation agent was investigated through three approaches of focusing on U, Mo extraction. The results indicate flotation beneficiation without followed metallurgical process is not appropriate because of high target metals loss rate via water leaching. H2SO4, H2O2 dosage recommended to oxidation leaching are 10 and 6–8% of ore mass, and U, Mo leaching rate are 92.71 and 52.16% respectively. For the acid pressure leaching, U, Mo leaching rate 93.75 and 76.07% are achieved under optimal temperature 130–140 °C and H2O2 dosage 8% combined with pressure air 0.6 MPa. Fluidized bed furnace roasting parameters include air flow rate 0.64 m/s, air ore ratio 0.3 m 3/kg at roasting temperature 550 °C with U, Mo leaching rate 93.2 and 89.5%, so enhanced metallurgical process effectively destroy wrapper and increase metal recovery rate.

Mar 1, 2018